]> git.kernelconcepts.de Git - karo-tx-linux.git/blob - Documentation/devicetree/bindings/spi/spi-davinci.txt
Merge branch 'fixes' of git://ftp.arm.linux.org.uk/~rmk/linux-arm
[karo-tx-linux.git] / Documentation / devicetree / bindings / spi / spi-davinci.txt
1 Davinci SPI controller device bindings
2
3 Links on DM:
4 Keystone 2 - http://www.ti.com/lit/ug/sprugp2a/sprugp2a.pdf
5 dm644x - http://www.ti.com/lit/ug/sprue32a/sprue32a.pdf
6 OMAP-L138/da830 - http://www.ti.com/lit/ug/spruh77a/spruh77a.pdf
7
8 Required properties:
9 - #address-cells: number of cells required to define a chip select
10         address on the SPI bus. Should be set to 1.
11 - #size-cells: should be zero.
12 - compatible:
13         - "ti,dm6441-spi" for SPI used similar to that on DM644x SoC family
14         - "ti,da830-spi" for SPI used similar to that on DA8xx SoC family
15         - "ti,keystone-spi" for SPI used similar to that on Keystone2 SoC
16                 family
17 - reg: Offset and length of SPI controller register space
18 - num-cs: Number of chip selects. This includes internal as well as
19         GPIO chip selects.
20 - ti,davinci-spi-intr-line: interrupt line used to connect the SPI
21         IP to the interrupt controller within the SoC. Possible values
22         are 0 and 1. Manual says one of the two possible interrupt
23         lines can be tied to the interrupt controller. Set this
24         based on a specifc SoC configuration.
25 - interrupts: interrupt number mapped to CPU.
26 - clocks: spi clk phandle
27
28 Optional:
29 - cs-gpios: gpio chip selects
30         For example to have 3 internal CS and 2 GPIO CS, user could define
31         cs-gpios = <0>, <0>, <0>, <&gpio1 30 0>, <&gpio1 31 0>;
32         where first three are internal CS and last two are GPIO CS.
33
34 Optional properties for slave devices:
35 SPI slave nodes can contain the following properties.
36 Not all SPI Peripherals from Texas Instruments support this.
37 Please check SPI peripheral documentation for a device before using these.
38
39 - ti,spi-wdelay : delay between transmission of words
40         (SPIFMTn.WDELAY, SPIDAT1.WDEL) must be specified in number of SPI module
41         clock periods.
42
43         delay = WDELAY * SPI_module_clock_period + 2 * SPI_module_clock_period
44
45 Below is timing diagram which shows functional meaning of
46 "ti,spi-wdelay" parameter.
47
48              +-+ +-+ +-+ +-+ +-+                           +-+ +-+ +-+
49 SPI_CLK      | | | | | | | | | |                           | | | | | |
50   +----------+ +-+ +-+ +-+ +-+ +---------------------------+ +-+ +-+ +-
51
52 SPI_SOMI/SIMO+-----------------+                           +-----------
53   +----------+ word1           +---------------------------+word2
54              +-----------------+                           +-----------
55                                           WDELAY
56                                 <-------------------------->
57
58 Example of a NOR flash slave device (n25q032) connected to DaVinci
59 SPI controller device over the SPI bus.
60
61 spi0:spi@20BF0000 {
62         #address-cells                  = <1>;
63         #size-cells                     = <0>;
64         compatible                      = "ti,dm6446-spi";
65         reg                             = <0x20BF0000 0x1000>;
66         num-cs                          = <4>;
67         ti,davinci-spi-intr-line        = <0>;
68         interrupts                      = <338>;
69         clocks                          = <&clkspi>;
70
71         flash: n25q032@0 {
72                 #address-cells = <1>;
73                 #size-cells = <1>;
74                 compatible = "st,m25p32";
75                 spi-max-frequency = <25000000>;
76                 reg = <0>;
77                 ti,spi-wdelay = <8>;
78
79                 partition@0 {
80                         label = "u-boot-spl";
81                         reg = <0x0 0x80000>;
82                         read-only;
83                 };
84
85                 partition@1 {
86                         label = "test";
87                         reg = <0x80000 0x380000>;
88                 };
89         };
90 };