2 * linux/arch/arm/mach-omap2/board-omap3logic.c
4 * Copyright (C) 2010 Li-Pro.Net
5 * Stephan Linz <linz@li-pro.net>
7 * Copyright (C) 2010-2012 Logic Product Development, Inc.
8 * Peter Barada <peter.barada@logicpd.com>
9 * Ashwin BIhari <ashwin.bihari@logicpd.com>
11 * Modified from Beagle, EVM, and RX51
13 * This program is free software; you can redistribute it and/or modify
14 * it under the terms of the GNU General Public License version 2 as
15 * published by the Free Software Foundation.
18 #include <linux/kernel.h>
19 #include <linux/init.h>
20 #include <linux/platform_device.h>
21 #include <linux/delay.h>
22 #include <linux/err.h>
23 #include <linux/clk.h>
25 #include <linux/gpio.h>
27 #include <linux/regulator/fixed.h>
28 #include <linux/regulator/machine.h>
30 #include <linux/i2c/twl.h>
31 #include <linux/mmc/host.h>
33 #include <mach/hardware.h>
34 #include <asm/mach-types.h>
35 #include <asm/mach/arch.h>
36 #include <asm/mach/map.h>
41 #include "common-board-devices.h"
44 #include <plat/board.h>
46 #include <plat/gpmc-smsc911x.h>
47 #include <plat/gpmc.h>
48 #include <plat/sdrc.h>
51 #define OMAP3LOGIC_SMSC911X_CS 1
53 #define OMAP3530_LV_SOM_MMC_GPIO_CD 110
54 #define OMAP3530_LV_SOM_MMC_GPIO_WP 126
55 #define OMAP3530_LV_SOM_SMSC911X_GPIO_IRQ 152
57 #define OMAP3_TORPEDO_MMC_GPIO_CD 127
58 #define OMAP3_TORPEDO_SMSC911X_GPIO_IRQ 129
60 static struct regulator_consumer_supply omap3logic_vmmc1_supply[] = {
61 REGULATOR_SUPPLY("vmmc", "omap_hsmmc.0"),
64 /* VMMC1 for MMC1 pins CMD, CLK, DAT0..DAT3 (20 mA, plus card == max 220 mA) */
65 static struct regulator_init_data omap3logic_vmmc1 = {
70 .valid_modes_mask = REGULATOR_MODE_NORMAL
71 | REGULATOR_MODE_STANDBY,
72 .valid_ops_mask = REGULATOR_CHANGE_VOLTAGE
73 | REGULATOR_CHANGE_MODE
74 | REGULATOR_CHANGE_STATUS,
76 .num_consumer_supplies = ARRAY_SIZE(omap3logic_vmmc1_supply),
77 .consumer_supplies = omap3logic_vmmc1_supply,
80 static struct twl4030_gpio_platform_data omap3logic_gpio_data = {
81 .gpio_base = OMAP_MAX_GPIO_LINES,
82 .irq_base = TWL4030_GPIO_IRQ_BASE,
83 .irq_end = TWL4030_GPIO_IRQ_END,
86 .pulldowns = BIT(2) | BIT(6) | BIT(7) | BIT(8)
87 | BIT(13) | BIT(15) | BIT(16) | BIT(17),
90 static struct twl4030_usb_data omap3logic_usb_data = {
91 .usb_mode = T2_USB_MODE_ULPI,
95 static struct twl4030_platform_data omap3logic_twldata = {
96 .irq_base = TWL4030_IRQ_BASE,
97 .irq_end = TWL4030_IRQ_END,
99 /* platform_data for children goes here */
100 .gpio = &omap3logic_gpio_data,
101 .vmmc1 = &omap3logic_vmmc1,
102 .usb = &omap3logic_usb_data,
105 static int __init omap3logic_i2c_init(void)
107 omap3_pmic_init("twl4030", &omap3logic_twldata);
111 static struct omap2_hsmmc_info __initdata board_mmc_info[] = {
115 .caps = MMC_CAP_4_BIT_DATA,
122 static void __init board_mmc_init(void)
124 if (machine_is_omap3530_lv_som()) {
125 /* OMAP3530 LV SOM board */
126 board_mmc_info[0].gpio_cd = OMAP3530_LV_SOM_MMC_GPIO_CD;
127 board_mmc_info[0].gpio_wp = OMAP3530_LV_SOM_MMC_GPIO_WP;
128 omap_mux_init_signal("gpio_110", OMAP_PIN_OUTPUT);
129 omap_mux_init_signal("gpio_126", OMAP_PIN_OUTPUT);
130 } else if (machine_is_omap3_torpedo()) {
131 /* OMAP3 Torpedo board */
132 board_mmc_info[0].gpio_cd = OMAP3_TORPEDO_MMC_GPIO_CD;
133 omap_mux_init_signal("gpio_127", OMAP_PIN_OUTPUT);
135 /* unsupported board */
136 printk(KERN_ERR "%s(): unknown machine type\n", __func__);
140 omap_hsmmc_init(board_mmc_info);
143 static struct omap_smsc911x_platform_data __initdata board_smsc911x_data = {
144 .cs = OMAP3LOGIC_SMSC911X_CS,
146 .gpio_reset = -EINVAL,
149 /* TODO/FIXME (comment by Peter Barada, LogicPD):
150 * Fix the PBIAS voltage for Torpedo MMC1 pins that
151 * are used for other needs (IRQs, etc). */
152 static void omap3torpedo_fix_pbias_voltage(void)
154 u16 control_pbias_offset = OMAP343X_CONTROL_PBIAS_LITE;
157 if (machine_is_omap3_torpedo())
159 /* Set the bias for the pin */
160 reg = omap_ctrl_readl(control_pbias_offset);
162 reg &= ~OMAP343X_PBIASLITEPWRDNZ1;
163 omap_ctrl_writel(reg, control_pbias_offset);
165 /* 100ms delay required for PBIAS configuration */
168 reg |= OMAP343X_PBIASLITEVMODE1;
169 reg |= OMAP343X_PBIASLITEPWRDNZ1;
170 omap_ctrl_writel(reg | 0x300, control_pbias_offset);
174 static inline void __init board_smsc911x_init(void)
176 if (machine_is_omap3530_lv_som()) {
177 /* OMAP3530 LV SOM board */
178 board_smsc911x_data.gpio_irq =
179 OMAP3530_LV_SOM_SMSC911X_GPIO_IRQ;
180 omap_mux_init_signal("gpio_152", OMAP_PIN_INPUT);
181 } else if (machine_is_omap3_torpedo()) {
182 /* OMAP3 Torpedo board */
183 board_smsc911x_data.gpio_irq = OMAP3_TORPEDO_SMSC911X_GPIO_IRQ;
184 omap_mux_init_signal("gpio_129", OMAP_PIN_INPUT);
186 /* unsupported board */
187 printk(KERN_ERR "%s(): unknown machine type\n", __func__);
191 gpmc_smsc911x_init(&board_smsc911x_data);
194 #ifdef CONFIG_OMAP_MUX
195 static struct omap_board_mux board_mux[] __initdata = {
197 OMAP3_MUX(HSUSB0_CLK, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
198 OMAP3_MUX(HSUSB0_STP, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
199 OMAP3_MUX(HSUSB0_DIR, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
200 OMAP3_MUX(HSUSB0_NXT, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
201 OMAP3_MUX(HSUSB0_DATA0, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
202 OMAP3_MUX(HSUSB0_DATA1, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
203 OMAP3_MUX(HSUSB0_DATA2, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
204 OMAP3_MUX(HSUSB0_DATA3, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
205 OMAP3_MUX(HSUSB0_DATA4, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
206 OMAP3_MUX(HSUSB0_DATA5, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
207 OMAP3_MUX(HSUSB0_DATA6, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
208 OMAP3_MUX(HSUSB0_DATA7, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
210 { .reg_offset = OMAP_MUX_TERMINATOR },
214 static struct regulator_consumer_supply dummy_supplies[] = {
215 REGULATOR_SUPPLY("vddvario", "smsc911x.0"),
216 REGULATOR_SUPPLY("vdd33a", "smsc911x.0"),
219 static void __init omap3logic_init(void)
221 regulator_register_fixed(0, dummy_supplies, ARRAY_SIZE(dummy_supplies));
222 omap3_mux_init(board_mux, OMAP_PACKAGE_CBB);
223 omap3torpedo_fix_pbias_voltage();
224 omap3logic_i2c_init();
226 omap_sdrc_init(NULL, NULL);
228 board_smsc911x_init();
232 /* Ensure SDRC pins are mux'd for self-refresh */
233 omap_mux_init_signal("sdrc_cke0", OMAP_PIN_OUTPUT);
234 omap_mux_init_signal("sdrc_cke1", OMAP_PIN_OUTPUT);
237 MACHINE_START(OMAP3_TORPEDO, "Logic OMAP3 Torpedo board")
238 .atag_offset = 0x100,
239 .reserve = omap_reserve,
240 .map_io = omap3_map_io,
241 .init_early = omap35xx_init_early,
242 .init_irq = omap3_init_irq,
243 .handle_irq = omap3_intc_handle_irq,
244 .init_machine = omap3logic_init,
245 .init_late = omap35xx_init_late,
246 .timer = &omap3_timer,
247 .restart = omap_prcm_restart,
250 MACHINE_START(OMAP3530_LV_SOM, "OMAP Logic 3530 LV SOM board")
251 .atag_offset = 0x100,
252 .reserve = omap_reserve,
253 .map_io = omap3_map_io,
254 .init_early = omap35xx_init_early,
255 .init_irq = omap3_init_irq,
256 .handle_irq = omap3_intc_handle_irq,
257 .init_machine = omap3logic_init,
258 .init_late = omap35xx_init_late,
259 .timer = &omap3_timer,
260 .restart = omap_prcm_restart,