drivers/i2c/busses/i2c-exynos5.c

   1 /**
   2  * i2c-exynos5.c - Samsung Exynos5 I2C Controller Driver
   3  *
   4  * Copyright (C) 2013 Samsung Electronics Co., Ltd.
   5  *
   6  * This program is free software; you can redistribute it and/or modify
   7  * it under the terms of the GNU General Public License version 2 as
   8  * published by the Free Software Foundation.
   9 */
  10
  11 #include <linux/kernel.h>
  12 #include <linux/module.h>
  13
  14 #include <linux/i2c.h>
  15 #include <linux/time.h>
  16 #include <linux/interrupt.h>
  17 #include <linux/delay.h>
  18 #include <linux/errno.h>
  19 #include <linux/err.h>
  20 #include <linux/platform_device.h>
  21 #include <linux/clk.h>
  22 #include <linux/slab.h>
  23 #include <linux/io.h>
  24 #include <linux/of_address.h>
  25 #include <linux/of_irq.h>
  26 #include <linux/spinlock.h>
  27
  28 /*
  29  * HSI2C controller from Samsung supports 2 modes of operation
  30  * 1. Auto mode: Where in master automatically controls the whole transaction
  31  * 2. Manual mode: Software controls the transaction by issuing commands
  32  *    START, READ, WRITE, STOP, RESTART in I2C_MANUAL_CMD register.
  33  *
  34  * Operation mode can be selected by setting AUTO_MODE bit in I2C_CONF register
  35  *
  36  * Special bits are available for both modes of operation to set commands
  37  * and for checking transfer status
  38  */
  39
  40 /* Register Map */
  41 #define HSI2C_CTL               0x00
  42 #define HSI2C_FIFO_CTL          0x04
  43 #define HSI2C_TRAILIG_CTL       0x08
  44 #define HSI2C_CLK_CTL           0x0C
  45 #define HSI2C_CLK_SLOT          0x10
  46 #define HSI2C_INT_ENABLE        0x20
  47 #define HSI2C_INT_STATUS        0x24
  48 #define HSI2C_ERR_STATUS        0x2C
  49 #define HSI2C_FIFO_STATUS       0x30
  50 #define HSI2C_TX_DATA           0x34
  51 #define HSI2C_RX_DATA           0x38
  52 #define HSI2C_CONF              0x40
  53 #define HSI2C_AUTO_CONF         0x44
  54 #define HSI2C_TIMEOUT           0x48
  55 #define HSI2C_MANUAL_CMD        0x4C
  56 #define HSI2C_TRANS_STATUS      0x50
  57 #define HSI2C_TIMING_HS1        0x54
  58 #define HSI2C_TIMING_HS2        0x58
  59 #define HSI2C_TIMING_HS3        0x5C
  60 #define HSI2C_TIMING_FS1        0x60
  61 #define HSI2C_TIMING_FS2        0x64
  62 #define HSI2C_TIMING_FS3        0x68
  63 #define HSI2C_TIMING_SLA        0x6C
  64 #define HSI2C_ADDR              0x70
  65
  66 /* I2C_CTL Register bits */
  67 #define HSI2C_FUNC_MODE_I2C                     (1u << 0)
  68 #define HSI2C_MASTER                            (1u << 3)
  69 #define HSI2C_RXCHON                            (1u << 6)
  70 #define HSI2C_TXCHON                            (1u << 7)
  71 #define HSI2C_SW_RST                            (1u << 31)
  72
  73 /* I2C_FIFO_CTL Register bits */
  74 #define HSI2C_RXFIFO_EN                         (1u << 0)
  75 #define HSI2C_TXFIFO_EN                         (1u << 1)
  76 #define HSI2C_RXFIFO_TRIGGER_LEVEL(x)           ((x) << 4)
  77 #define HSI2C_TXFIFO_TRIGGER_LEVEL(x)           ((x) << 16)
  78
  79 /* I2C_TRAILING_CTL Register bits */
  80 #define HSI2C_TRAILING_COUNT                    (0xf)
  81
  82 /* I2C_INT_EN Register bits */
  83 #define HSI2C_INT_TX_ALMOSTEMPTY_EN             (1u << 0)
  84 #define HSI2C_INT_RX_ALMOSTFULL_EN              (1u << 1)
  85 #define HSI2C_INT_TRAILING_EN                   (1u << 6)
  86
  87 /* I2C_INT_STAT Register bits */
  88 #define HSI2C_INT_TX_ALMOSTEMPTY                (1u << 0)
  89 #define HSI2C_INT_RX_ALMOSTFULL                 (1u << 1)
  90 #define HSI2C_INT_TX_UNDERRUN                   (1u << 2)
  91 #define HSI2C_INT_TX_OVERRUN                    (1u << 3)
  92 #define HSI2C_INT_RX_UNDERRUN                   (1u << 4)
  93 #define HSI2C_INT_RX_OVERRUN                    (1u << 5)
  94 #define HSI2C_INT_TRAILING                      (1u << 6)
  95 #define HSI2C_INT_I2C                           (1u << 9)
  96
  97 #define HSI2C_INT_TRANS_DONE                    (1u << 7)
  98 #define HSI2C_INT_TRANS_ABORT                   (1u << 8)
  99 #define HSI2C_INT_NO_DEV_ACK                    (1u << 9)
 100 #define HSI2C_INT_NO_DEV                        (1u << 10)
 101 #define HSI2C_INT_TIMEOUT                       (1u << 11)
 102 #define HSI2C_INT_I2C_TRANS                     (HSI2C_INT_TRANS_DONE | \
 103                                                 HSI2C_INT_TRANS_ABORT | \
 104                                                 HSI2C_INT_NO_DEV_ACK |  \
 105                                                 HSI2C_INT_NO_DEV |      \
 106                                                 HSI2C_INT_TIMEOUT)
 107
 108 /* I2C_FIFO_STAT Register bits */
 109 #define HSI2C_RX_FIFO_EMPTY                     (1u << 24)
 110 #define HSI2C_RX_FIFO_FULL                      (1u << 23)
 111 #define HSI2C_RX_FIFO_LVL(x)                    ((x >> 16) & 0x7f)
 112 #define HSI2C_TX_FIFO_EMPTY                     (1u << 8)
 113 #define HSI2C_TX_FIFO_FULL                      (1u << 7)
 114 #define HSI2C_TX_FIFO_LVL(x)                    ((x >> 0) & 0x7f)
 115
 116 /* I2C_CONF Register bits */
 117 #define HSI2C_AUTO_MODE                         (1u << 31)
 118 #define HSI2C_10BIT_ADDR_MODE                   (1u << 30)
 119 #define HSI2C_HS_MODE                           (1u << 29)
 120
 121 /* I2C_AUTO_CONF Register bits */
 122 #define HSI2C_READ_WRITE                        (1u << 16)
 123 #define HSI2C_STOP_AFTER_TRANS                  (1u << 17)
 124 #define HSI2C_MASTER_RUN                        (1u << 31)
 125
 126 /* I2C_TIMEOUT Register bits */
 127 #define HSI2C_TIMEOUT_EN                        (1u << 31)
 128 #define HSI2C_TIMEOUT_MASK                      0xff
 129
 130 /* I2C_TRANS_STATUS register bits */
 131 #define HSI2C_MASTER_BUSY                       (1u << 17)
 132 #define HSI2C_SLAVE_BUSY                        (1u << 16)
 133
 134 /* I2C_TRANS_STATUS register bits for Exynos5 variant */
 135 #define HSI2C_TIMEOUT_AUTO                      (1u << 4)
 136 #define HSI2C_NO_DEV                            (1u << 3)
 137 #define HSI2C_NO_DEV_ACK                        (1u << 2)
 138 #define HSI2C_TRANS_ABORT                       (1u << 1)
 139 #define HSI2C_TRANS_DONE                        (1u << 0)
 140
 141 /* I2C_TRANS_STATUS register bits for Exynos7 variant */
 142 #define HSI2C_MASTER_ST_MASK                    0xf
 143 #define HSI2C_MASTER_ST_IDLE                    0x0
 144 #define HSI2C_MASTER_ST_START                   0x1
 145 #define HSI2C_MASTER_ST_RESTART                 0x2
 146 #define HSI2C_MASTER_ST_STOP                    0x3
 147 #define HSI2C_MASTER_ST_MASTER_ID               0x4
 148 #define HSI2C_MASTER_ST_ADDR0                   0x5
 149 #define HSI2C_MASTER_ST_ADDR1                   0x6
 150 #define HSI2C_MASTER_ST_ADDR2                   0x7
 151 #define HSI2C_MASTER_ST_ADDR_SR                 0x8
 152 #define HSI2C_MASTER_ST_READ                    0x9
 153 #define HSI2C_MASTER_ST_WRITE                   0xa
 154 #define HSI2C_MASTER_ST_NO_ACK                  0xb
 155 #define HSI2C_MASTER_ST_LOSE                    0xc
 156 #define HSI2C_MASTER_ST_WAIT                    0xd
 157 #define HSI2C_MASTER_ST_WAIT_CMD                0xe
 158
 159 /* I2C_ADDR register bits */
 160 #define HSI2C_SLV_ADDR_SLV(x)                   ((x & 0x3ff) << 0)
 161 #define HSI2C_SLV_ADDR_MAS(x)                   ((x & 0x3ff) << 10)
 162 #define HSI2C_MASTER_ID(x)                      ((x & 0xff) << 24)
 163 #define MASTER_ID(x)                            ((x & 0x7) + 0x08)
 164
 165 /*
 166  * Controller operating frequency, timing values for operation
 167  * are calculated against this frequency
 168  */
 169 #define HSI2C_HS_TX_CLOCK       1000000
 170 #define HSI2C_FS_TX_CLOCK       100000
 171 #define HSI2C_HIGH_SPD          1
 172 #define HSI2C_FAST_SPD          0
 173
 174 #define EXYNOS5_I2C_TIMEOUT (msecs_to_jiffies(1000))
 175
 176 #define HSI2C_EXYNOS7   BIT(0)
 177
 178 struct exynos5_i2c {
 179         struct i2c_adapter      adap;
 180         unsigned int            suspended:1;
 181
 182         struct i2c_msg          *msg;
 183         struct completion       msg_complete;
 184         unsigned int            msg_ptr;
 185
 186         unsigned int            irq;
 187
 188         void __iomem            *regs;
 189         struct clk              *clk;
 190         struct device           *dev;
 191         int                     state;
 192
 193         spinlock_t              lock;           /* IRQ synchronization */
 194
 195         /*
 196          * Since the TRANS_DONE bit is cleared on read, and we may read it
 197          * either during an IRQ or after a transaction, keep track of its
 198          * state here.
 199          */
 200         int                     trans_done;
 201
 202         /* Controller operating frequency */
 203         unsigned int            fs_clock;
 204         unsigned int            hs_clock;
 205
 206         /*
 207          * HSI2C Controller can operate in
 208          * 1. High speed upto 3.4Mbps
 209          * 2. Fast speed upto 1Mbps
 210          */
 211         int                     speed_mode;
 212
 213         /* Version of HS-I2C Hardware */
 214         struct exynos_hsi2c_variant     *variant;
 215 };
 216
 217 /**
 218  * struct exynos_hsi2c_variant - platform specific HSI2C driver data
 219  * @fifo_depth: the fifo depth supported by the HSI2C module
 220  *
 221  * Specifies platform specific configuration of HSI2C module.
 222  * Note: A structure for driver specific platform data is used for future
 223  * expansion of its usage.
 224  */
 225 struct exynos_hsi2c_variant {
 226         unsigned int    fifo_depth;
 227         unsigned int    hw;
 228 };
 229
 230 static const struct exynos_hsi2c_variant exynos5250_hsi2c_data = {
 231         .fifo_depth     = 64,
 232 };
 233
 234 static const struct exynos_hsi2c_variant exynos5260_hsi2c_data = {
 235         .fifo_depth     = 16,
 236 };
 237
 238 static const struct exynos_hsi2c_variant exynos7_hsi2c_data = {
 239         .fifo_depth     = 16,
 240         .hw             = HSI2C_EXYNOS7,
 241 };
 242
 243 static const struct of_device_id exynos5_i2c_match[] = {
 244         {
 245                 .compatible = "samsung,exynos5-hsi2c",
 246                 .data = &exynos5250_hsi2c_data
 247         }, {
 248                 .compatible = "samsung,exynos5250-hsi2c",
 249                 .data = &exynos5250_hsi2c_data
 250         }, {
 251                 .compatible = "samsung,exynos5260-hsi2c",
 252                 .data = &exynos5260_hsi2c_data
 253         }, {
 254                 .compatible = "samsung,exynos7-hsi2c",
 255                 .data = &exynos7_hsi2c_data
 256         }, {},
 257 };
 258 MODULE_DEVICE_TABLE(of, exynos5_i2c_match);
 259
 260 static inline struct exynos_hsi2c_variant *exynos5_i2c_get_variant
 261                                         (struct platform_device *pdev)
 262 {
 263         const struct of_device_id *match;
 264
 265         match = of_match_node(exynos5_i2c_match, pdev->dev.of_node);
 266         return (struct exynos_hsi2c_variant *)match->data;
 267 }
 268
 269 static void exynos5_i2c_clr_pend_irq(struct exynos5_i2c *i2c)
 270 {
 271         writel(readl(i2c->regs + HSI2C_INT_STATUS),
 272                                 i2c->regs + HSI2C_INT_STATUS);
 273 }
 274
 275 /*
 276  * exynos5_i2c_set_timing: updates the registers with appropriate
 277  * timing values calculated
 278  *
 279  * Returns 0 on success, -EINVAL if the cycle length cannot
 280  * be calculated.
 281  */
 282 static int exynos5_i2c_set_timing(struct exynos5_i2c *i2c, int mode)
 283 {
 284         u32 i2c_timing_s1;
 285         u32 i2c_timing_s2;
 286         u32 i2c_timing_s3;
 287         u32 i2c_timing_sla;
 288         unsigned int t_start_su, t_start_hd;
 289         unsigned int t_stop_su;
 290         unsigned int t_data_su, t_data_hd;
 291         unsigned int t_scl_l, t_scl_h;
 292         unsigned int t_sr_release;
 293         unsigned int t_ftl_cycle;
 294         unsigned int clkin = clk_get_rate(i2c->clk);
 295         unsigned int div, utemp0 = 0, utemp1 = 0, clk_cycle;
 296         unsigned int op_clk = (mode == HSI2C_HIGH_SPD) ?
 297                                 i2c->hs_clock : i2c->fs_clock;
 298
 299         /*
 300          * In case of HSI2C controller in Exynos5 series
 301          * FPCLK / FI2C =
 302          * (CLK_DIV + 1) * (TSCLK_L + TSCLK_H + 2) + 8 + 2 * FLT_CYCLE
 303          *
 304          * In case of HSI2C controllers in Exynos7 series
 305          * FPCLK / FI2C =
 306          * (CLK_DIV + 1) * (TSCLK_L + TSCLK_H + 2) + 8 + FLT_CYCLE
 307          *
 308          * utemp0 = (CLK_DIV + 1) * (TSCLK_L + TSCLK_H + 2)
 309          * utemp1 = (TSCLK_L + TSCLK_H + 2)
 310          */
 311         t_ftl_cycle = (readl(i2c->regs + HSI2C_CONF) >> 16) & 0x7;
 312         utemp0 = (clkin / op_clk) - 8;
 313
 314         if (i2c->variant->hw == HSI2C_EXYNOS7)
 315                 utemp0 -= t_ftl_cycle;
 316         else
 317                 utemp0 -= 2 * t_ftl_cycle;
 318
 319         /* CLK_DIV max is 256 */
 320         for (div = 0; div < 256; div++) {
 321                 utemp1 = utemp0 / (div + 1);
 322
 323                 /*
 324                  * SCL_L and SCL_H each has max value of 255
 325                  * Hence, For the clk_cycle to the have right value
 326                  * utemp1 has to be less then 512 and more than 4.
 327                  */
 328                 if ((utemp1 < 512) && (utemp1 > 4)) {
 329                         clk_cycle = utemp1 - 2;
 330                         break;
 331                 } else if (div == 255) {
 332                         dev_warn(i2c->dev, "Failed to calculate divisor");
 333                         return -EINVAL;
 334                 }
 335         }
 336
 337         t_scl_l = clk_cycle / 2;
 338         t_scl_h = clk_cycle / 2;
 339         t_start_su = t_scl_l;
 340         t_start_hd = t_scl_l;
 341         t_stop_su = t_scl_l;
 342         t_data_su = t_scl_l / 2;
 343         t_data_hd = t_scl_l / 2;
 344         t_sr_release = clk_cycle;
 345
 346         i2c_timing_s1 = t_start_su << 24 | t_start_hd << 16 | t_stop_su << 8;
 347         i2c_timing_s2 = t_data_su << 24 | t_scl_l << 8 | t_scl_h << 0;
 348         i2c_timing_s3 = div << 16 | t_sr_release << 0;
 349         i2c_timing_sla = t_data_hd << 0;
 350
 351         dev_dbg(i2c->dev, "tSTART_SU: %X, tSTART_HD: %X, tSTOP_SU: %X\n",
 352                 t_start_su, t_start_hd, t_stop_su);
 353         dev_dbg(i2c->dev, "tDATA_SU: %X, tSCL_L: %X, tSCL_H: %X\n",
 354                 t_data_su, t_scl_l, t_scl_h);
 355         dev_dbg(i2c->dev, "nClkDiv: %X, tSR_RELEASE: %X\n",
 356                 div, t_sr_release);
 357         dev_dbg(i2c->dev, "tDATA_HD: %X\n", t_data_hd);
 358
 359         if (mode == HSI2C_HIGH_SPD) {
 360                 writel(i2c_timing_s1, i2c->regs + HSI2C_TIMING_HS1);
 361                 writel(i2c_timing_s2, i2c->regs + HSI2C_TIMING_HS2);
 362                 writel(i2c_timing_s3, i2c->regs + HSI2C_TIMING_HS3);
 363         } else {
 364                 writel(i2c_timing_s1, i2c->regs + HSI2C_TIMING_FS1);
 365                 writel(i2c_timing_s2, i2c->regs + HSI2C_TIMING_FS2);
 366                 writel(i2c_timing_s3, i2c->regs + HSI2C_TIMING_FS3);
 367         }
 368         writel(i2c_timing_sla, i2c->regs + HSI2C_TIMING_SLA);
 369
 370         return 0;
 371 }
 372
 373 static int exynos5_hsi2c_clock_setup(struct exynos5_i2c *i2c)
 374 {
 375         /*
 376          * Configure the Fast speed timing values
 377          * Even the High Speed mode initially starts with Fast mode
 378          */
 379         if (exynos5_i2c_set_timing(i2c, HSI2C_FAST_SPD)) {
 380                 dev_err(i2c->dev, "HSI2C FS Clock set up failed\n");
 381                 return -EINVAL;
 382         }
 383
 384         /* configure the High speed timing values */
 385         if (i2c->speed_mode == HSI2C_HIGH_SPD) {
 386                 if (exynos5_i2c_set_timing(i2c, HSI2C_HIGH_SPD)) {
 387                         dev_err(i2c->dev, "HSI2C HS Clock set up failed\n");
 388                         return -EINVAL;
 389                 }
 390         }
 391
 392         return 0;
 393 }
 394
 395 /*
 396  * exynos5_i2c_init: configures the controller for I2C functionality
 397  * Programs I2C controller for Master mode operation
 398  */
 399 static void exynos5_i2c_init(struct exynos5_i2c *i2c)
 400 {
 401         u32 i2c_conf = readl(i2c->regs + HSI2C_CONF);
 402         u32 i2c_timeout = readl(i2c->regs + HSI2C_TIMEOUT);
 403
 404         /* Clear to disable Timeout */
 405         i2c_timeout &= ~HSI2C_TIMEOUT_EN;
 406         writel(i2c_timeout, i2c->regs + HSI2C_TIMEOUT);
 407
 408         writel((HSI2C_FUNC_MODE_I2C | HSI2C_MASTER),
 409                                         i2c->regs + HSI2C_CTL);
 410         writel(HSI2C_TRAILING_COUNT, i2c->regs + HSI2C_TRAILIG_CTL);
 411
 412         if (i2c->speed_mode == HSI2C_HIGH_SPD) {
 413                 writel(HSI2C_MASTER_ID(MASTER_ID(i2c->adap.nr)),
 414                                         i2c->regs + HSI2C_ADDR);
 415                 i2c_conf |= HSI2C_HS_MODE;
 416         }
 417
 418         writel(i2c_conf | HSI2C_AUTO_MODE, i2c->regs + HSI2C_CONF);
 419 }
 420
 421 static void exynos5_i2c_reset(struct exynos5_i2c *i2c)
 422 {
 423         u32 i2c_ctl;
 424
 425         /* Set and clear the bit for reset */
 426         i2c_ctl = readl(i2c->regs + HSI2C_CTL);
 427         i2c_ctl |= HSI2C_SW_RST;
 428         writel(i2c_ctl, i2c->regs + HSI2C_CTL);
 429
 430         i2c_ctl = readl(i2c->regs + HSI2C_CTL);
 431         i2c_ctl &= ~HSI2C_SW_RST;
 432         writel(i2c_ctl, i2c->regs + HSI2C_CTL);
 433
 434         /* We don't expect calculations to fail during the run */
 435         exynos5_hsi2c_clock_setup(i2c);
 436         /* Initialize the configure registers */
 437         exynos5_i2c_init(i2c);
 438 }
 439
 440 /*
 441  * exynos5_i2c_irq: top level IRQ servicing routine
 442  *
 443  * INT_STATUS registers gives the interrupt details. Further,
 444  * FIFO_STATUS or TRANS_STATUS registers are to be check for detailed
 445  * state of the bus.
 446  */
 447 static irqreturn_t exynos5_i2c_irq(int irqno, void *dev_id)
 448 {
 449         struct exynos5_i2c *i2c = dev_id;
 450         u32 fifo_level, int_status, fifo_status, trans_status;
 451         unsigned char byte;
 452         int len = 0;
 453
 454         i2c->state = -EINVAL;
 455
 456         spin_lock(&i2c->lock);
 457
 458         int_status = readl(i2c->regs + HSI2C_INT_STATUS);
 459         writel(int_status, i2c->regs + HSI2C_INT_STATUS);
 460         trans_status = readl(i2c->regs + HSI2C_TRANS_STATUS);
 461
 462         /* handle interrupt related to the transfer status */
 463         if (i2c->variant->hw == HSI2C_EXYNOS7) {
 464                 if (int_status & HSI2C_INT_TRANS_DONE) {
 465                         i2c->trans_done = 1;
 466                         i2c->state = 0;
 467                 } else if (int_status & HSI2C_INT_TRANS_ABORT) {
 468                         dev_dbg(i2c->dev, "Deal with arbitration lose\n");
 469                         i2c->state = -EAGAIN;
 470                         goto stop;
 471                 } else if (int_status & HSI2C_INT_NO_DEV_ACK) {
 472                         dev_dbg(i2c->dev, "No ACK from device\n");
 473                         i2c->state = -ENXIO;
 474                         goto stop;
 475                 } else if (int_status & HSI2C_INT_NO_DEV) {
 476                         dev_dbg(i2c->dev, "No device\n");
 477                         i2c->state = -ENXIO;
 478                         goto stop;
 479                 } else if (int_status & HSI2C_INT_TIMEOUT) {
 480                         dev_dbg(i2c->dev, "Accessing device timed out\n");
 481                         i2c->state = -ETIMEDOUT;
 482                         goto stop;
 483                 }
 484
 485                 if ((trans_status & HSI2C_MASTER_ST_MASK) == HSI2C_MASTER_ST_LOSE) {
 486                         i2c->state = -EAGAIN;
 487                         goto stop;
 488                 }
 489         } else if (int_status & HSI2C_INT_I2C) {
 490                 if (trans_status & HSI2C_NO_DEV_ACK) {
 491                         dev_dbg(i2c->dev, "No ACK from device\n");
 492                         i2c->state = -ENXIO;
 493                         goto stop;
 494                 } else if (trans_status & HSI2C_NO_DEV) {
 495                         dev_dbg(i2c->dev, "No device\n");
 496                         i2c->state = -ENXIO;
 497                         goto stop;
 498                 } else if (trans_status & HSI2C_TRANS_ABORT) {
 499                         dev_dbg(i2c->dev, "Deal with arbitration lose\n");
 500                         i2c->state = -EAGAIN;
 501                         goto stop;
 502                 } else if (trans_status & HSI2C_TIMEOUT_AUTO) {
 503                         dev_dbg(i2c->dev, "Accessing device timed out\n");
 504                         i2c->state = -ETIMEDOUT;
 505                         goto stop;
 506                 } else if (trans_status & HSI2C_TRANS_DONE) {
 507                         i2c->trans_done = 1;
 508                         i2c->state = 0;
 509                 }
 510         }
 511
 512         if ((i2c->msg->flags & I2C_M_RD) && (int_status &
 513                         (HSI2C_INT_TRAILING | HSI2C_INT_RX_ALMOSTFULL))) {
 514                 fifo_status = readl(i2c->regs + HSI2C_FIFO_STATUS);
 515                 fifo_level = HSI2C_RX_FIFO_LVL(fifo_status);
 516                 len = min(fifo_level, i2c->msg->len - i2c->msg_ptr);
 517
 518                 while (len > 0) {
 519                         byte = (unsigned char)
 520                                 readl(i2c->regs + HSI2C_RX_DATA);
 521                         i2c->msg->buf[i2c->msg_ptr++] = byte;
 522                         len--;
 523                 }
 524                 i2c->state = 0;
 525         } else if (int_status & HSI2C_INT_TX_ALMOSTEMPTY) {
 526                 fifo_status = readl(i2c->regs + HSI2C_FIFO_STATUS);
 527                 fifo_level = HSI2C_TX_FIFO_LVL(fifo_status);
 528
 529                 len = i2c->variant->fifo_depth - fifo_level;
 530                 if (len > (i2c->msg->len - i2c->msg_ptr)) {
 531                         u32 int_en = readl(i2c->regs + HSI2C_INT_ENABLE);
 532
 533                         int_en &= ~HSI2C_INT_TX_ALMOSTEMPTY_EN;
 534                         writel(int_en, i2c->regs + HSI2C_INT_ENABLE);
 535                         len = i2c->msg->len - i2c->msg_ptr;
 536                 }
 537
 538                 while (len > 0) {
 539                         byte = i2c->msg->buf[i2c->msg_ptr++];
 540                         writel(byte, i2c->regs + HSI2C_TX_DATA);
 541                         len--;
 542                 }
 543                 i2c->state = 0;
 544         }
 545
 546  stop:
 547         if ((i2c->trans_done && (i2c->msg->len == i2c->msg_ptr)) ||
 548             (i2c->state < 0)) {
 549                 writel(0, i2c->regs + HSI2C_INT_ENABLE);
 550                 exynos5_i2c_clr_pend_irq(i2c);
 551                 complete(&i2c->msg_complete);
 552         }
 553
 554         spin_unlock(&i2c->lock);
 555
 556         return IRQ_HANDLED;
 557 }
 558
 559 /*
 560  * exynos5_i2c_wait_bus_idle
 561  *
 562  * Wait for the bus to go idle, indicated by the MASTER_BUSY bit being
 563  * cleared.
 564  *
 565  * Returns -EBUSY if the bus cannot be bought to idle
 566  */
 567 static int exynos5_i2c_wait_bus_idle(struct exynos5_i2c *i2c)
 568 {
 569         unsigned long stop_time;
 570         u32 trans_status;
 571
 572         /* wait for 100 milli seconds for the bus to be idle */
 573         stop_time = jiffies + msecs_to_jiffies(100) + 1;
 574         do {
 575                 trans_status = readl(i2c->regs + HSI2C_TRANS_STATUS);
 576                 if (!(trans_status & HSI2C_MASTER_BUSY))
 577                         return 0;
 578
 579                 usleep_range(50, 200);
 580         } while (time_before(jiffies, stop_time));
 581
 582         return -EBUSY;
 583 }
 584
 585 /*
 586  * exynos5_i2c_message_start: Configures the bus and starts the xfer
 587  * i2c: struct exynos5_i2c pointer for the current bus
 588  * stop: Enables stop after transfer if set. Set for last transfer of
 589  *       in the list of messages.
 590  *
 591  * Configures the bus for read/write function
 592  * Sets chip address to talk to, message length to be sent.
 593  * Enables appropriate interrupts and sends start xfer command.
 594  */
 595 static void exynos5_i2c_message_start(struct exynos5_i2c *i2c, int stop)
 596 {
 597         u32 i2c_ctl;
 598         u32 int_en = 0;
 599         u32 i2c_auto_conf = 0;
 600         u32 fifo_ctl;
 601         unsigned long flags;
 602         unsigned short trig_lvl;
 603
 604         if (i2c->variant->hw == HSI2C_EXYNOS7)
 605                 int_en |= HSI2C_INT_I2C_TRANS;
 606         else
 607                 int_en |= HSI2C_INT_I2C;
 608
 609         i2c_ctl = readl(i2c->regs + HSI2C_CTL);
 610         i2c_ctl &= ~(HSI2C_TXCHON | HSI2C_RXCHON);
 611         fifo_ctl = HSI2C_RXFIFO_EN | HSI2C_TXFIFO_EN;
 612
 613         if (i2c->msg->flags & I2C_M_RD) {
 614                 i2c_ctl |= HSI2C_RXCHON;
 615
 616                 i2c_auto_conf |= HSI2C_READ_WRITE;
 617
 618                 trig_lvl = (i2c->msg->len > i2c->variant->fifo_depth) ?
 619                         (i2c->variant->fifo_depth * 3 / 4) : i2c->msg->len;
 620                 fifo_ctl |= HSI2C_RXFIFO_TRIGGER_LEVEL(trig_lvl);
 621
 622                 int_en |= (HSI2C_INT_RX_ALMOSTFULL_EN |
 623                         HSI2C_INT_TRAILING_EN);
 624         } else {
 625                 i2c_ctl |= HSI2C_TXCHON;
 626
 627                 trig_lvl = (i2c->msg->len > i2c->variant->fifo_depth) ?
 628                         (i2c->variant->fifo_depth * 1 / 4) : i2c->msg->len;
 629                 fifo_ctl |= HSI2C_TXFIFO_TRIGGER_LEVEL(trig_lvl);
 630
 631                 int_en |= HSI2C_INT_TX_ALMOSTEMPTY_EN;
 632         }
 633
 634         writel(HSI2C_SLV_ADDR_MAS(i2c->msg->addr), i2c->regs + HSI2C_ADDR);
 635
 636         writel(fifo_ctl, i2c->regs + HSI2C_FIFO_CTL);
 637         writel(i2c_ctl, i2c->regs + HSI2C_CTL);
 638
 639         /*
 640          * Enable interrupts before starting the transfer so that we don't
 641          * miss any INT_I2C interrupts.
 642          */
 643         spin_lock_irqsave(&i2c->lock, flags);
 644         writel(int_en, i2c->regs + HSI2C_INT_ENABLE);
 645
 646         if (stop == 1)
 647                 i2c_auto_conf |= HSI2C_STOP_AFTER_TRANS;
 648         i2c_auto_conf |= i2c->msg->len;
 649         i2c_auto_conf |= HSI2C_MASTER_RUN;
 650         writel(i2c_auto_conf, i2c->regs + HSI2C_AUTO_CONF);
 651         spin_unlock_irqrestore(&i2c->lock, flags);
 652 }
 653
 654 static int exynos5_i2c_xfer_msg(struct exynos5_i2c *i2c,
 655                               struct i2c_msg *msgs, int stop)
 656 {
 657         unsigned long timeout;
 658         int ret;
 659
 660         i2c->msg = msgs;
 661         i2c->msg_ptr = 0;
 662         i2c->trans_done = 0;
 663
 664         reinit_completion(&i2c->msg_complete);
 665
 666         exynos5_i2c_message_start(i2c, stop);
 667
 668         timeout = wait_for_completion_timeout(&i2c->msg_complete,
 669                                               EXYNOS5_I2C_TIMEOUT);
 670         if (timeout == 0)
 671                 ret = -ETIMEDOUT;
 672         else
 673                 ret = i2c->state;
 674
 675         /*
 676          * If this is the last message to be transfered (stop == 1)
 677          * Then check if the bus can be brought back to idle.
 678          */
 679         if (ret == 0 && stop)
 680                 ret = exynos5_i2c_wait_bus_idle(i2c);
 681
 682         if (ret < 0) {
 683                 exynos5_i2c_reset(i2c);
 684                 if (ret == -ETIMEDOUT)
 685                         dev_warn(i2c->dev, "%s timeout\n",
 686                                  (msgs->flags & I2C_M_RD) ? "rx" : "tx");
 687         }
 688
 689         /* Return the state as in interrupt routine */
 690         return ret;
 691 }
 692
 693 static int exynos5_i2c_xfer(struct i2c_adapter *adap,
 694                         struct i2c_msg *msgs, int num)
 695 {
 696         struct exynos5_i2c *i2c = adap->algo_data;
 697         int i = 0, ret = 0, stop = 0;
 698
 699         if (i2c->suspended) {
 700                 dev_err(i2c->dev, "HS-I2C is not initialized.\n");
 701                 return -EIO;
 702         }
 703
 704         ret = clk_enable(i2c->clk);
 705         if (ret)
 706                 return ret;
 707
 708         for (i = 0; i < num; i++, msgs++) {
 709                 stop = (i == num - 1);
 710
 711                 ret = exynos5_i2c_xfer_msg(i2c, msgs, stop);
 712
 713                 if (ret < 0)
 714                         goto out;
 715         }
 716
 717         if (i == num) {
 718                 ret = num;
 719         } else {
 720                 /* Only one message, cannot access the device */
 721                 if (i == 1)
 722                         ret = -EREMOTEIO;
 723                 else
 724                         ret = i;
 725
 726                 dev_warn(i2c->dev, "xfer message failed\n");
 727         }
 728
 729  out:
 730         clk_disable(i2c->clk);
 731         return ret;
 732 }
 733
 734 static u32 exynos5_i2c_func(struct i2c_adapter *adap)
 735 {
 736         return I2C_FUNC_I2C | (I2C_FUNC_SMBUS_EMUL & ~I2C_FUNC_SMBUS_QUICK);
 737 }
 738
 739 static const struct i2c_algorithm exynos5_i2c_algorithm = {
 740         .master_xfer            = exynos5_i2c_xfer,
 741         .functionality          = exynos5_i2c_func,
 742 };
 743
 744 static int exynos5_i2c_probe(struct platform_device *pdev)
 745 {
 746         struct device_node *np = pdev->dev.of_node;
 747         struct exynos5_i2c *i2c;
 748         struct resource *mem;
 749         unsigned int op_clock;
 750         int ret;
 751
 752         i2c = devm_kzalloc(&pdev->dev, sizeof(struct exynos5_i2c), GFP_KERNEL);
 753         if (!i2c)
 754                 return -ENOMEM;
 755
 756         if (of_property_read_u32(np, "clock-frequency", &op_clock)) {
 757                 i2c->speed_mode = HSI2C_FAST_SPD;
 758                 i2c->fs_clock = HSI2C_FS_TX_CLOCK;
 759         } else {
 760                 if (op_clock >= HSI2C_HS_TX_CLOCK) {
 761                         i2c->speed_mode = HSI2C_HIGH_SPD;
 762                         i2c->fs_clock = HSI2C_FS_TX_CLOCK;
 763                         i2c->hs_clock = op_clock;
 764                 } else {
 765                         i2c->speed_mode = HSI2C_FAST_SPD;
 766                         i2c->fs_clock = op_clock;
 767                 }
 768         }
 769
 770         strlcpy(i2c->adap.name, "exynos5-i2c", sizeof(i2c->adap.name));
 771         i2c->adap.owner   = THIS_MODULE;
 772         i2c->adap.algo    = &exynos5_i2c_algorithm;
 773         i2c->adap.retries = 3;
 774
 775         i2c->dev = &pdev->dev;
 776         i2c->clk = devm_clk_get(&pdev->dev, "hsi2c");
 777         if (IS_ERR(i2c->clk)) {
 778                 dev_err(&pdev->dev, "cannot get clock\n");
 779                 return -ENOENT;
 780         }
 781
 782         ret = clk_prepare_enable(i2c->clk);
 783         if (ret)
 784                 return ret;
 785
 786         mem = platform_get_resource(pdev, IORESOURCE_MEM, 0);
 787         i2c->regs = devm_ioremap_resource(&pdev->dev, mem);
 788         if (IS_ERR(i2c->regs)) {
 789                 ret = PTR_ERR(i2c->regs);
 790                 goto err_clk;
 791         }
 792
 793         i2c->adap.dev.of_node = np;
 794         i2c->adap.algo_data = i2c;
 795         i2c->adap.dev.parent = &pdev->dev;
 796
 797         /* Clear pending interrupts from u-boot or misc causes */
 798         exynos5_i2c_clr_pend_irq(i2c);
 799
 800         spin_lock_init(&i2c->lock);
 801         init_completion(&i2c->msg_complete);
 802
 803         i2c->irq = ret = platform_get_irq(pdev, 0);
 804         if (ret <= 0) {
 805                 dev_err(&pdev->dev, "cannot find HS-I2C IRQ\n");
 806                 ret = -EINVAL;
 807                 goto err_clk;
 808         }
 809
 810         ret = devm_request_irq(&pdev->dev, i2c->irq, exynos5_i2c_irq,
 811                                 IRQF_NO_SUSPEND | IRQF_ONESHOT,
 812                                 dev_name(&pdev->dev), i2c);
 813
 814         if (ret != 0) {
 815                 dev_err(&pdev->dev, "cannot request HS-I2C IRQ %d\n", i2c->irq);
 816                 goto err_clk;
 817         }
 818
 819         /* Need to check the variant before setting up. */
 820         i2c->variant = exynos5_i2c_get_variant(pdev);
 821
 822         ret = exynos5_hsi2c_clock_setup(i2c);
 823         if (ret)
 824                 goto err_clk;
 825
 826         exynos5_i2c_reset(i2c);
 827
 828         ret = i2c_add_adapter(&i2c->adap);
 829         if (ret < 0)
 830                 goto err_clk;
 831
 832         platform_set_drvdata(pdev, i2c);
 833
 834         clk_disable(i2c->clk);
 835
 836         return 0;
 837
 838  err_clk:
 839         clk_disable_unprepare(i2c->clk);
 840         return ret;
 841 }
 842
 843 static int exynos5_i2c_remove(struct platform_device *pdev)
 844 {
 845         struct exynos5_i2c *i2c = platform_get_drvdata(pdev);
 846
 847         i2c_del_adapter(&i2c->adap);
 848
 849         clk_unprepare(i2c->clk);
 850
 851         return 0;
 852 }
 853
 854 #ifdef CONFIG_PM_SLEEP
 855 static int exynos5_i2c_suspend_noirq(struct device *dev)
 856 {
 857         struct platform_device *pdev = to_platform_device(dev);
 858         struct exynos5_i2c *i2c = platform_get_drvdata(pdev);
 859
 860         i2c->suspended = 1;
 861
 862         clk_unprepare(i2c->clk);
 863
 864         return 0;
 865 }
 866
 867 static int exynos5_i2c_resume_noirq(struct device *dev)
 868 {
 869         struct platform_device *pdev = to_platform_device(dev);
 870         struct exynos5_i2c *i2c = platform_get_drvdata(pdev);
 871         int ret = 0;
 872
 873         ret = clk_prepare_enable(i2c->clk);
 874         if (ret)
 875                 return ret;
 876
 877         ret = exynos5_hsi2c_clock_setup(i2c);
 878         if (ret) {
 879                 clk_disable_unprepare(i2c->clk);
 880                 return ret;
 881         }
 882
 883         exynos5_i2c_init(i2c);
 884         clk_disable(i2c->clk);
 885         i2c->suspended = 0;
 886
 887         return 0;
 888 }
 889 #endif
 890
 891 static const struct dev_pm_ops exynos5_i2c_dev_pm_ops = {
 892         SET_NOIRQ_SYSTEM_SLEEP_PM_OPS(exynos5_i2c_suspend_noirq,
 893                                       exynos5_i2c_resume_noirq)
 894 };
 895
 896 static struct platform_driver exynos5_i2c_driver = {
 897         .probe          = exynos5_i2c_probe,
 898         .remove         = exynos5_i2c_remove,
 899         .driver         = {
 900                 .name   = "exynos5-hsi2c",
 901                 .pm     = &exynos5_i2c_dev_pm_ops,
 902                 .of_match_table = exynos5_i2c_match,
 903         },
 904 };
 905
 906 module_platform_driver(exynos5_i2c_driver);
 907
 908 MODULE_DESCRIPTION("Exynos5 HS-I2C Bus driver");
 909 MODULE_AUTHOR("Naveen Krishna Chatradhi, <ch.naveen@samsung.com>");
 910 MODULE_AUTHOR("Taekgyun Ko, <taeggyun.ko@samsung.com>");
 911 MODULE_LICENSE("GPL v2");