drivers/media/i2c/s5k6aa.c

   1 /*
   2  * Driver for Samsung S5K6AAFX SXGA 1/6" 1.3M CMOS Image Sensor
   3  * with embedded SoC ISP.
   4  *
   5  * Copyright (C) 2011, Samsung Electronics Co., Ltd.
   6  * Sylwester Nawrocki <s.nawrocki@samsung.com>
   7  *
   8  * Based on a driver authored by Dongsoo Nathaniel Kim.
   9  * Copyright (C) 2009, Dongsoo Nathaniel Kim <dongsoo45.kim@samsung.com>
  10  *
  11  * This program is free software; you can redistribute it and/or modify
  12  * it under the terms of the GNU General Public License as published by
  13  * the Free Software Foundation; either version 2 of the License, or
  14  * (at your option) any later version.
  15  */
  16
  17 #include <linux/clk.h>
  18 #include <linux/delay.h>
  19 #include <linux/gpio.h>
  20 #include <linux/i2c.h>
  21 #include <linux/media.h>
  22 #include <linux/module.h>
  23 #include <linux/regulator/consumer.h>
  24 #include <linux/slab.h>
  25
  26 #include <media/media-entity.h>
  27 #include <media/v4l2-ctrls.h>
  28 #include <media/v4l2-device.h>
  29 #include <media/v4l2-subdev.h>
  30 #include <media/v4l2-mediabus.h>
  31 #include <media/s5k6aa.h>
  32
  33 static int debug;
  34 module_param(debug, int, 0644);
  35
  36 #define DRIVER_NAME                     "S5K6AA"
  37
  38 /* The token to indicate array termination */
  39 #define S5K6AA_TERM                     0xffff
  40 #define S5K6AA_OUT_WIDTH_DEF            640
  41 #define S5K6AA_OUT_HEIGHT_DEF           480
  42 #define S5K6AA_WIN_WIDTH_MAX            1280
  43 #define S5K6AA_WIN_HEIGHT_MAX           1024
  44 #define S5K6AA_WIN_WIDTH_MIN            8
  45 #define S5K6AA_WIN_HEIGHT_MIN           8
  46
  47 /*
  48  * H/W register Interface (0xD0000000 - 0xD0000FFF)
  49  */
  50 #define AHB_MSB_ADDR_PTR                0xfcfc
  51 #define GEN_REG_OFFSH                   0xd000
  52 #define REG_CMDWR_ADDRH                 0x0028
  53 #define REG_CMDWR_ADDRL                 0x002a
  54 #define REG_CMDRD_ADDRH                 0x002c
  55 #define REG_CMDRD_ADDRL                 0x002e
  56 #define REG_CMDBUF0_ADDR                0x0f12
  57 #define REG_CMDBUF1_ADDR                0x0f10
  58
  59 /*
  60  * Host S/W Register interface (0x70000000 - 0x70002000)
  61  * The value of the two most significant address bytes is 0x7000,
  62  * (HOST_SWIF_OFFS_H). The register addresses below specify 2 LSBs.
  63  */
  64 #define HOST_SWIF_OFFSH                 0x7000
  65
  66 /* Initialization parameters */
  67 /* Master clock frequency in KHz */
  68 #define REG_I_INCLK_FREQ_L              0x01b8
  69 #define REG_I_INCLK_FREQ_H              0x01ba
  70 #define  MIN_MCLK_FREQ_KHZ              6000U
  71 #define  MAX_MCLK_FREQ_KHZ              27000U
  72 #define REG_I_USE_NPVI_CLOCKS           0x01c6
  73 #define REG_I_USE_NMIPI_CLOCKS          0x01c8
  74
  75 /* Clock configurations, n = 0..2. REG_I_* frequency unit is 4 kHz. */
  76 #define REG_I_OPCLK_4KHZ(n)             ((n) * 6 + 0x01cc)
  77 #define REG_I_MIN_OUTRATE_4KHZ(n)       ((n) * 6 + 0x01ce)
  78 #define REG_I_MAX_OUTRATE_4KHZ(n)       ((n) * 6 + 0x01d0)
  79 #define  SYS_PLL_OUT_FREQ               (48000000 / 4000)
  80 #define  PCLK_FREQ_MIN                  (24000000 / 4000)
  81 #define  PCLK_FREQ_MAX                  (48000000 / 4000)
  82 #define REG_I_INIT_PARAMS_UPDATED       0x01e0
  83 #define REG_I_ERROR_INFO                0x01e2
  84
  85 /* General purpose parameters */
  86 #define REG_USER_BRIGHTNESS             0x01e4
  87 #define REG_USER_CONTRAST               0x01e6
  88 #define REG_USER_SATURATION             0x01e8
  89 #define REG_USER_SHARPBLUR              0x01ea
  90
  91 #define REG_G_SPEC_EFFECTS              0x01ee
  92 #define REG_G_ENABLE_PREV               0x01f0
  93 #define REG_G_ENABLE_PREV_CHG           0x01f2
  94 #define REG_G_NEW_CFG_SYNC              0x01f8
  95 #define REG_G_PREVZOOM_IN_WIDTH         0x020a
  96 #define REG_G_PREVZOOM_IN_HEIGHT        0x020c
  97 #define REG_G_PREVZOOM_IN_XOFFS         0x020e
  98 #define REG_G_PREVZOOM_IN_YOFFS         0x0210
  99 #define REG_G_INPUTS_CHANGE_REQ         0x021a
 100 #define REG_G_ACTIVE_PREV_CFG           0x021c
 101 #define REG_G_PREV_CFG_CHG              0x021e
 102 #define REG_G_PREV_OPEN_AFTER_CH        0x0220
 103 #define REG_G_PREV_CFG_ERROR            0x0222
 104
 105 /* Preview control section. n = 0...4. */
 106 #define PREG(n, x)                      ((n) * 0x26 + x)
 107 #define REG_P_OUT_WIDTH(n)              PREG(n, 0x0242)
 108 #define REG_P_OUT_HEIGHT(n)             PREG(n, 0x0244)
 109 #define REG_P_FMT(n)                    PREG(n, 0x0246)
 110 #define REG_P_MAX_OUT_RATE(n)           PREG(n, 0x0248)
 111 #define REG_P_MIN_OUT_RATE(n)           PREG(n, 0x024a)
 112 #define REG_P_PVI_MASK(n)               PREG(n, 0x024c)
 113 #define REG_P_CLK_INDEX(n)              PREG(n, 0x024e)
 114 #define REG_P_FR_RATE_TYPE(n)           PREG(n, 0x0250)
 115 #define  FR_RATE_DYNAMIC                0
 116 #define  FR_RATE_FIXED                  1
 117 #define  FR_RATE_FIXED_ACCURATE         2
 118 #define REG_P_FR_RATE_Q_TYPE(n)         PREG(n, 0x0252)
 119 #define  FR_RATE_Q_BEST_FRRATE          1 /* Binning enabled */
 120 #define  FR_RATE_Q_BEST_QUALITY         2 /* Binning disabled */
 121 /* Frame period in 0.1 ms units */
 122 #define REG_P_MAX_FR_TIME(n)            PREG(n, 0x0254)
 123 #define REG_P_MIN_FR_TIME(n)            PREG(n, 0x0256)
 124 /* Conversion to REG_P_[MAX/MIN]_FR_TIME value; __t: time in us */
 125 #define  US_TO_FR_TIME(__t)             ((__t) / 100)
 126 #define  S5K6AA_MIN_FR_TIME             33300  /* us */
 127 #define  S5K6AA_MAX_FR_TIME             650000 /* us */
 128 #define  S5K6AA_MAX_HIGHRES_FR_TIME     666    /* x100 us */
 129 /* The below 5 registers are for "device correction" values */
 130 #define REG_P_COLORTEMP(n)              PREG(n, 0x025e)
 131 #define REG_P_PREV_MIRROR(n)            PREG(n, 0x0262)
 132
 133 /* Extended image property controls */
 134 /* Exposure time in 10 us units */
 135 #define REG_SF_USR_EXPOSURE_L           0x03c6
 136 #define REG_SF_USR_EXPOSURE_H           0x03c8
 137 #define REG_SF_USR_EXPOSURE_CHG         0x03ca
 138 #define REG_SF_USR_TOT_GAIN             0x03cc
 139 #define REG_SF_USR_TOT_GAIN_CHG         0x03ce
 140 #define REG_SF_RGAIN                    0x03d0
 141 #define REG_SF_RGAIN_CHG                0x03d2
 142 #define REG_SF_GGAIN                    0x03d4
 143 #define REG_SF_GGAIN_CHG                0x03d6
 144 #define REG_SF_BGAIN                    0x03d8
 145 #define REG_SF_BGAIN_CHG                0x03da
 146 #define REG_SF_FLICKER_QUANT            0x03dc
 147 #define REG_SF_FLICKER_QUANT_CHG        0x03de
 148
 149 /* Output interface (parallel/MIPI) setup */
 150 #define REG_OIF_EN_MIPI_LANES           0x03fa
 151 #define REG_OIF_EN_PACKETS              0x03fc
 152 #define REG_OIF_CFG_CHG                 0x03fe
 153
 154 /* Auto-algorithms enable mask */
 155 #define REG_DBG_AUTOALG_EN              0x0400
 156 #define  AALG_ALL_EN_MASK               (1 << 0)
 157 #define  AALG_AE_EN_MASK                (1 << 1)
 158 #define  AALG_DIVLEI_EN_MASK            (1 << 2)
 159 #define  AALG_WB_EN_MASK                (1 << 3)
 160 #define  AALG_FLICKER_EN_MASK           (1 << 5)
 161 #define  AALG_FIT_EN_MASK               (1 << 6)
 162 #define  AALG_WRHW_EN_MASK              (1 << 7)
 163
 164 /* Firmware revision information */
 165 #define REG_FW_APIVER                   0x012e
 166 #define  S5K6AAFX_FW_APIVER             0x0001
 167 #define REG_FW_REVISION                 0x0130
 168
 169 /* For now we use only one user configuration register set */
 170 #define S5K6AA_MAX_PRESETS              1
 171
 172 static const char * const s5k6aa_supply_names[] = {
 173         "vdd_core",     /* Digital core supply 1.5V (1.4V to 1.6V) */
 174         "vdda",         /* Analog power supply 2.8V (2.6V to 3.0V) */
 175         "vdd_reg",      /* Regulator input power 1.8V (1.7V to 1.9V)
 176                            or 2.8V (2.6V to 3.0) */
 177         "vddio",        /* I/O supply 1.8V (1.65V to 1.95V)
 178                            or 2.8V (2.5V to 3.1V) */
 179 };
 180 #define S5K6AA_NUM_SUPPLIES ARRAY_SIZE(s5k6aa_supply_names)
 181
 182 enum s5k6aa_gpio_id {
 183         STBY,
 184         RST,
 185         GPIO_NUM,
 186 };
 187
 188 struct s5k6aa_regval {
 189         u16 addr;
 190         u16 val;
 191 };
 192
 193 struct s5k6aa_pixfmt {
 194         enum v4l2_mbus_pixelcode code;
 195         u32 colorspace;
 196         /* REG_P_FMT(x) register value */
 197         u16 reg_p_fmt;
 198 };
 199
 200 struct s5k6aa_preset {
 201         /* output pixel format and resolution */
 202         struct v4l2_mbus_framefmt mbus_fmt;
 203         u8 clk_id;
 204         u8 index;
 205 };
 206
 207 struct s5k6aa_ctrls {
 208         struct v4l2_ctrl_handler handler;
 209         /* Auto / manual white balance cluster */
 210         struct v4l2_ctrl *awb;
 211         struct v4l2_ctrl *gain_red;
 212         struct v4l2_ctrl *gain_blue;
 213         struct v4l2_ctrl *gain_green;
 214         /* Mirror cluster */
 215         struct v4l2_ctrl *hflip;
 216         struct v4l2_ctrl *vflip;
 217         /* Auto exposure / manual exposure and gain cluster */
 218         struct v4l2_ctrl *auto_exp;
 219         struct v4l2_ctrl *exposure;
 220         struct v4l2_ctrl *gain;
 221 };
 222
 223 struct s5k6aa_interval {
 224         u16 reg_fr_time;
 225         struct v4l2_fract interval;
 226         /* Maximum rectangle for the interval */
 227         struct v4l2_frmsize_discrete size;
 228 };
 229
 230 struct s5k6aa {
 231         struct v4l2_subdev sd;
 232         struct media_pad pad;
 233
 234         enum v4l2_mbus_type bus_type;
 235         u8 mipi_lanes;
 236
 237         int (*s_power)(int enable);
 238         struct regulator_bulk_data supplies[S5K6AA_NUM_SUPPLIES];
 239         struct s5k6aa_gpio gpio[GPIO_NUM];
 240
 241         /* external master clock frequency */
 242         unsigned long mclk_frequency;
 243         /* ISP internal master clock frequency */
 244         u16 clk_fop;
 245         /* output pixel clock frequency range */
 246         u16 pclk_fmin;
 247         u16 pclk_fmax;
 248
 249         unsigned int inv_hflip:1;
 250         unsigned int inv_vflip:1;
 251
 252         /* protects the struct members below */
 253         struct mutex lock;
 254
 255         /* sensor matrix scan window */
 256         struct v4l2_rect ccd_rect;
 257
 258         struct s5k6aa_ctrls ctrls;
 259         struct s5k6aa_preset presets[S5K6AA_MAX_PRESETS];
 260         struct s5k6aa_preset *preset;
 261         const struct s5k6aa_interval *fiv;
 262
 263         unsigned int streaming:1;
 264         unsigned int apply_cfg:1;
 265         unsigned int apply_crop:1;
 266         unsigned int power;
 267 };
 268
 269 static struct s5k6aa_regval s5k6aa_analog_config[] = {
 270         /* Analog settings */
 271         { 0x112a, 0x0000 }, { 0x1132, 0x0000 },
 272         { 0x113e, 0x0000 }, { 0x115c, 0x0000 },
 273         { 0x1164, 0x0000 }, { 0x1174, 0x0000 },
 274         { 0x1178, 0x0000 }, { 0x077a, 0x0000 },
 275         { 0x077c, 0x0000 }, { 0x077e, 0x0000 },
 276         { 0x0780, 0x0000 }, { 0x0782, 0x0000 },
 277         { 0x0784, 0x0000 }, { 0x0786, 0x0000 },
 278         { 0x0788, 0x0000 }, { 0x07a2, 0x0000 },
 279         { 0x07a4, 0x0000 }, { 0x07a6, 0x0000 },
 280         { 0x07a8, 0x0000 }, { 0x07b6, 0x0000 },
 281         { 0x07b8, 0x0002 }, { 0x07ba, 0x0004 },
 282         { 0x07bc, 0x0004 }, { 0x07be, 0x0005 },
 283         { 0x07c0, 0x0005 }, { S5K6AA_TERM, 0 },
 284 };
 285
 286 /* TODO: Add RGB888 and Bayer format */
 287 static const struct s5k6aa_pixfmt s5k6aa_formats[] = {
 288         { V4L2_MBUS_FMT_YUYV8_2X8,      V4L2_COLORSPACE_JPEG,   5 },
 289         /* range 16-240 */
 290         { V4L2_MBUS_FMT_YUYV8_2X8,      V4L2_COLORSPACE_REC709, 6 },
 291         { V4L2_MBUS_FMT_RGB565_2X8_BE,  V4L2_COLORSPACE_JPEG,   0 },
 292 };
 293
 294 static const struct s5k6aa_interval s5k6aa_intervals[] = {
 295         { 1000, {10000, 1000000}, {1280, 1024} }, /* 10 fps */
 296         { 666,  {15000, 1000000}, {1280, 1024} }, /* 15 fps */
 297         { 500,  {20000, 1000000}, {1280, 720} },  /* 20 fps */
 298         { 400,  {25000, 1000000}, {640, 480} },   /* 25 fps */
 299         { 333,  {33300, 1000000}, {640, 480} },   /* 30 fps */
 300 };
 301
 302 #define S5K6AA_INTERVAL_DEF_INDEX 1 /* 15 fps */
 303
 304 static inline struct v4l2_subdev *ctrl_to_sd(struct v4l2_ctrl *ctrl)
 305 {
 306         return &container_of(ctrl->handler, struct s5k6aa, ctrls.handler)->sd;
 307 }
 308
 309 static inline struct s5k6aa *to_s5k6aa(struct v4l2_subdev *sd)
 310 {
 311         return container_of(sd, struct s5k6aa, sd);
 312 }
 313
 314 /* Set initial values for all preview presets */
 315 static void s5k6aa_presets_data_init(struct s5k6aa *s5k6aa)
 316 {
 317         struct s5k6aa_preset *preset = &s5k6aa->presets[0];
 318         int i;
 319
 320         for (i = 0; i < S5K6AA_MAX_PRESETS; i++) {
 321                 preset->mbus_fmt.width  = S5K6AA_OUT_WIDTH_DEF;
 322                 preset->mbus_fmt.height = S5K6AA_OUT_HEIGHT_DEF;
 323                 preset->mbus_fmt.code   = s5k6aa_formats[0].code;
 324                 preset->index           = i;
 325                 preset->clk_id          = 0;
 326                 preset++;
 327         }
 328
 329         s5k6aa->fiv = &s5k6aa_intervals[S5K6AA_INTERVAL_DEF_INDEX];
 330         s5k6aa->preset = &s5k6aa->presets[0];
 331 }
 332
 333 static int s5k6aa_i2c_read(struct i2c_client *client, u16 addr, u16 *val)
 334 {
 335         u8 wbuf[2] = {addr >> 8, addr & 0xFF};
 336         struct i2c_msg msg[2];
 337         u8 rbuf[2];
 338         int ret;
 339
 340         msg[0].addr = client->addr;
 341         msg[0].flags = 0;
 342         msg[0].len = 2;
 343         msg[0].buf = wbuf;
 344
 345         msg[1].addr = client->addr;
 346         msg[1].flags = I2C_M_RD;
 347         msg[1].len = 2;
 348         msg[1].buf = rbuf;
 349
 350         ret = i2c_transfer(client->adapter, msg, 2);
 351         *val = be16_to_cpu(*((u16 *)rbuf));
 352
 353         v4l2_dbg(3, debug, client, "i2c_read: 0x%04X : 0x%04x\n", addr, *val);
 354
 355         return ret == 2 ? 0 : ret;
 356 }
 357
 358 static int s5k6aa_i2c_write(struct i2c_client *client, u16 addr, u16 val)
 359 {
 360         u8 buf[4] = {addr >> 8, addr & 0xFF, val >> 8, val & 0xFF};
 361
 362         int ret = i2c_master_send(client, buf, 4);
 363         v4l2_dbg(3, debug, client, "i2c_write: 0x%04X : 0x%04x\n", addr, val);
 364
 365         return ret == 4 ? 0 : ret;
 366 }
 367
 368 /* The command register write, assumes Command_Wr_addH = 0x7000. */
 369 static int s5k6aa_write(struct i2c_client *c, u16 addr, u16 val)
 370 {
 371         int ret = s5k6aa_i2c_write(c, REG_CMDWR_ADDRL, addr);
 372         if (ret)
 373                 return ret;
 374         return s5k6aa_i2c_write(c, REG_CMDBUF0_ADDR, val);
 375 }
 376
 377 /* The command register read, assumes Command_Rd_addH = 0x7000. */
 378 static int s5k6aa_read(struct i2c_client *client, u16 addr, u16 *val)
 379 {
 380         int ret = s5k6aa_i2c_write(client, REG_CMDRD_ADDRL, addr);
 381         if (ret)
 382                 return ret;
 383         return s5k6aa_i2c_read(client, REG_CMDBUF0_ADDR, val);
 384 }
 385
 386 static int s5k6aa_write_array(struct v4l2_subdev *sd,
 387                               const struct s5k6aa_regval *msg)
 388 {
 389         struct i2c_client *client = v4l2_get_subdevdata(sd);
 390         u16 addr_incr = 0;
 391         int ret = 0;
 392
 393         while (msg->addr != S5K6AA_TERM) {
 394                 if (addr_incr != 2)
 395                         ret = s5k6aa_i2c_write(client, REG_CMDWR_ADDRL,
 396                                                msg->addr);
 397                 if (ret)
 398                         break;
 399                 ret = s5k6aa_i2c_write(client, REG_CMDBUF0_ADDR, msg->val);
 400                 if (ret)
 401                         break;
 402                 /* Assume that msg->addr is always less than 0xfffc */
 403                 addr_incr = (msg + 1)->addr - msg->addr;
 404                 msg++;
 405         }
 406
 407         return ret;
 408 }
 409
 410 /* Configure the AHB high address bytes for GTG registers access */
 411 static int s5k6aa_set_ahb_address(struct i2c_client *client)
 412 {
 413         int ret = s5k6aa_i2c_write(client, AHB_MSB_ADDR_PTR, GEN_REG_OFFSH);
 414         if (ret)
 415                 return ret;
 416         ret = s5k6aa_i2c_write(client, REG_CMDRD_ADDRH, HOST_SWIF_OFFSH);
 417         if (ret)
 418                 return ret;
 419         return s5k6aa_i2c_write(client, REG_CMDWR_ADDRH, HOST_SWIF_OFFSH);
 420 }
 421
 422 /**
 423  * s5k6aa_configure_pixel_clock - apply ISP main clock/PLL configuration
 424  *
 425  * Configure the internal ISP PLL for the required output frequency.
 426  * Locking: called with s5k6aa.lock mutex held.
 427  */
 428 static int s5k6aa_configure_pixel_clocks(struct s5k6aa *s5k6aa)
 429 {
 430         struct i2c_client *c = v4l2_get_subdevdata(&s5k6aa->sd);
 431         unsigned long fmclk = s5k6aa->mclk_frequency / 1000;
 432         u16 status;
 433         int ret;
 434
 435         if (WARN(fmclk < MIN_MCLK_FREQ_KHZ || fmclk > MAX_MCLK_FREQ_KHZ,
 436                  "Invalid clock frequency: %ld\n", fmclk))
 437                 return -EINVAL;
 438
 439         s5k6aa->pclk_fmin = PCLK_FREQ_MIN;
 440         s5k6aa->pclk_fmax = PCLK_FREQ_MAX;
 441         s5k6aa->clk_fop = SYS_PLL_OUT_FREQ;
 442
 443         /* External input clock frequency in kHz */
 444         ret = s5k6aa_write(c, REG_I_INCLK_FREQ_H, fmclk >> 16);
 445         if (!ret)
 446                 ret = s5k6aa_write(c, REG_I_INCLK_FREQ_L, fmclk & 0xFFFF);
 447         if (!ret)
 448                 ret = s5k6aa_write(c, REG_I_USE_NPVI_CLOCKS, 1);
 449         /* Internal PLL frequency */
 450         if (!ret)
 451                 ret = s5k6aa_write(c, REG_I_OPCLK_4KHZ(0), s5k6aa->clk_fop);
 452         if (!ret)
 453                 ret = s5k6aa_write(c, REG_I_MIN_OUTRATE_4KHZ(0),
 454                                    s5k6aa->pclk_fmin);
 455         if (!ret)
 456                 ret = s5k6aa_write(c, REG_I_MAX_OUTRATE_4KHZ(0),
 457                                    s5k6aa->pclk_fmax);
 458         if (!ret)
 459                 ret = s5k6aa_write(c, REG_I_INIT_PARAMS_UPDATED, 1);
 460         if (!ret)
 461                 ret = s5k6aa_read(c, REG_I_ERROR_INFO, &status);
 462
 463         return ret ? ret : (status ? -EINVAL : 0);
 464 }
 465
 466 /* Set horizontal and vertical image flipping */
 467 static int s5k6aa_set_mirror(struct s5k6aa *s5k6aa, int horiz_flip)
 468 {
 469         struct i2c_client *client = v4l2_get_subdevdata(&s5k6aa->sd);
 470         int index = s5k6aa->preset->index;
 471
 472         unsigned int vflip = s5k6aa->ctrls.vflip->val ^ s5k6aa->inv_vflip;
 473         unsigned int flip = (horiz_flip ^ s5k6aa->inv_hflip) | (vflip << 1);
 474
 475         return s5k6aa_write(client, REG_P_PREV_MIRROR(index), flip);
 476 }
 477
 478 /* Configure auto/manual white balance and R/G/B gains */
 479 static int s5k6aa_set_awb(struct s5k6aa *s5k6aa, int awb)
 480 {
 481         struct i2c_client *c = v4l2_get_subdevdata(&s5k6aa->sd);
 482         struct s5k6aa_ctrls *ctrls = &s5k6aa->ctrls;
 483         u16 reg;
 484
 485         int ret = s5k6aa_read(c, REG_DBG_AUTOALG_EN, &reg);
 486
 487         if (!ret && !awb) {
 488                 ret = s5k6aa_write(c, REG_SF_RGAIN, ctrls->gain_red->val);
 489                 if (!ret)
 490                         ret = s5k6aa_write(c, REG_SF_RGAIN_CHG, 1);
 491                 if (ret)
 492                         return ret;
 493
 494                 ret = s5k6aa_write(c, REG_SF_GGAIN, ctrls->gain_green->val);
 495                 if (!ret)
 496                         ret = s5k6aa_write(c, REG_SF_GGAIN_CHG, 1);
 497                 if (ret)
 498                         return ret;
 499
 500                 ret = s5k6aa_write(c, REG_SF_BGAIN, ctrls->gain_blue->val);
 501                 if (!ret)
 502                         ret = s5k6aa_write(c, REG_SF_BGAIN_CHG, 1);
 503         }
 504         if (!ret) {
 505                 reg = awb ? reg | AALG_WB_EN_MASK : reg & ~AALG_WB_EN_MASK;
 506                 ret = s5k6aa_write(c, REG_DBG_AUTOALG_EN, reg);
 507         }
 508
 509         return ret;
 510 }
 511
 512 /* Program FW with exposure time, 'exposure' in us units */
 513 static int s5k6aa_set_user_exposure(struct i2c_client *client, int exposure)
 514 {
 515         unsigned int time = exposure / 10;
 516
 517         int ret = s5k6aa_write(client, REG_SF_USR_EXPOSURE_L, time & 0xffff);
 518         if (!ret)
 519                 ret = s5k6aa_write(client, REG_SF_USR_EXPOSURE_H, time >> 16);
 520         if (ret)
 521                 return ret;
 522         return s5k6aa_write(client, REG_SF_USR_EXPOSURE_CHG, 1);
 523 }
 524
 525 static int s5k6aa_set_user_gain(struct i2c_client *client, int gain)
 526 {
 527         int ret = s5k6aa_write(client, REG_SF_USR_TOT_GAIN, gain);
 528         if (ret)
 529                 return ret;
 530         return s5k6aa_write(client, REG_SF_USR_TOT_GAIN_CHG, 1);
 531 }
 532
 533 /* Set auto/manual exposure and total gain */
 534 static int s5k6aa_set_auto_exposure(struct s5k6aa *s5k6aa, int value)
 535 {
 536         struct i2c_client *c = v4l2_get_subdevdata(&s5k6aa->sd);
 537         unsigned int exp_time = s5k6aa->ctrls.exposure->val;
 538         u16 auto_alg;
 539
 540         int ret = s5k6aa_read(c, REG_DBG_AUTOALG_EN, &auto_alg);
 541         if (ret)
 542                 return ret;
 543
 544         v4l2_dbg(1, debug, c, "man_exp: %d, auto_exp: %d, a_alg: 0x%x\n",
 545                  exp_time, value, auto_alg);
 546
 547         if (value == V4L2_EXPOSURE_AUTO) {
 548                 auto_alg |= AALG_AE_EN_MASK | AALG_DIVLEI_EN_MASK;
 549         } else {
 550                 ret = s5k6aa_set_user_exposure(c, exp_time);
 551                 if (ret)
 552                         return ret;
 553                 ret = s5k6aa_set_user_gain(c, s5k6aa->ctrls.gain->val);
 554                 if (ret)
 555                         return ret;
 556                 auto_alg &= ~(AALG_AE_EN_MASK | AALG_DIVLEI_EN_MASK);
 557         }
 558
 559         return s5k6aa_write(c, REG_DBG_AUTOALG_EN, auto_alg);
 560 }
 561
 562 static int s5k6aa_set_anti_flicker(struct s5k6aa *s5k6aa, int value)
 563 {
 564         struct i2c_client *client = v4l2_get_subdevdata(&s5k6aa->sd);
 565         u16 auto_alg;
 566         int ret;
 567
 568         ret = s5k6aa_read(client, REG_DBG_AUTOALG_EN, &auto_alg);
 569         if (ret)
 570                 return ret;
 571
 572         if (value == V4L2_CID_POWER_LINE_FREQUENCY_AUTO) {
 573                 auto_alg |= AALG_FLICKER_EN_MASK;
 574         } else {
 575                 auto_alg &= ~AALG_FLICKER_EN_MASK;
 576                 /* The V4L2_CID_LINE_FREQUENCY control values match
 577                  * the register values */
 578                 ret = s5k6aa_write(client, REG_SF_FLICKER_QUANT, value);
 579                 if (ret)
 580                         return ret;
 581                 ret = s5k6aa_write(client, REG_SF_FLICKER_QUANT_CHG, 1);
 582                 if (ret)
 583                         return ret;
 584         }
 585
 586         return s5k6aa_write(client, REG_DBG_AUTOALG_EN, auto_alg);
 587 }
 588
 589 static int s5k6aa_set_colorfx(struct s5k6aa *s5k6aa, int val)
 590 {
 591         struct i2c_client *client = v4l2_get_subdevdata(&s5k6aa->sd);
 592         static const struct v4l2_control colorfx[] = {
 593                 { V4L2_COLORFX_NONE,     0 },
 594                 { V4L2_COLORFX_BW,       1 },
 595                 { V4L2_COLORFX_NEGATIVE, 2 },
 596                 { V4L2_COLORFX_SEPIA,    3 },
 597                 { V4L2_COLORFX_SKY_BLUE, 4 },
 598                 { V4L2_COLORFX_SKETCH,   5 },
 599         };
 600         int i;
 601
 602         for (i = 0; i < ARRAY_SIZE(colorfx); i++) {
 603                 if (colorfx[i].id == val)
 604                         return s5k6aa_write(client, REG_G_SPEC_EFFECTS,
 605                                             colorfx[i].value);
 606         }
 607         return -EINVAL;
 608 }
 609
 610 static int s5k6aa_preview_config_status(struct i2c_client *client)
 611 {
 612         u16 error = 0;
 613         int ret = s5k6aa_read(client, REG_G_PREV_CFG_ERROR, &error);
 614
 615         v4l2_dbg(1, debug, client, "error: 0x%x (%d)\n", error, ret);
 616         return ret ? ret : (error ? -EINVAL : 0);
 617 }
 618
 619 static int s5k6aa_get_pixfmt_index(struct s5k6aa *s5k6aa,
 620                                    struct v4l2_mbus_framefmt *mf)
 621 {
 622         unsigned int i;
 623
 624         for (i = 0; i < ARRAY_SIZE(s5k6aa_formats); i++)
 625                 if (mf->colorspace == s5k6aa_formats[i].colorspace &&
 626                     mf->code == s5k6aa_formats[i].code)
 627                         return i;
 628         return 0;
 629 }
 630
 631 static int s5k6aa_set_output_framefmt(struct s5k6aa *s5k6aa,
 632                                       struct s5k6aa_preset *preset)
 633 {
 634         struct i2c_client *client = v4l2_get_subdevdata(&s5k6aa->sd);
 635         int fmt_index = s5k6aa_get_pixfmt_index(s5k6aa, &preset->mbus_fmt);
 636         int ret;
 637
 638         ret = s5k6aa_write(client, REG_P_OUT_WIDTH(preset->index),
 639                            preset->mbus_fmt.width);
 640         if (!ret)
 641                 ret = s5k6aa_write(client, REG_P_OUT_HEIGHT(preset->index),
 642                                    preset->mbus_fmt.height);
 643         if (!ret)
 644                 ret = s5k6aa_write(client, REG_P_FMT(preset->index),
 645                                    s5k6aa_formats[fmt_index].reg_p_fmt);
 646         return ret;
 647 }
 648
 649 static int s5k6aa_set_input_params(struct s5k6aa *s5k6aa)
 650 {
 651         struct i2c_client *c = v4l2_get_subdevdata(&s5k6aa->sd);
 652         struct v4l2_rect *r = &s5k6aa->ccd_rect;
 653         int ret;
 654
 655         ret = s5k6aa_write(c, REG_G_PREVZOOM_IN_WIDTH, r->width);
 656         if (!ret)
 657                 ret = s5k6aa_write(c, REG_G_PREVZOOM_IN_HEIGHT, r->height);
 658         if (!ret)
 659                 ret = s5k6aa_write(c, REG_G_PREVZOOM_IN_XOFFS, r->left);
 660         if (!ret)
 661                 ret = s5k6aa_write(c, REG_G_PREVZOOM_IN_YOFFS, r->top);
 662         if (!ret)
 663                 ret = s5k6aa_write(c, REG_G_INPUTS_CHANGE_REQ, 1);
 664         if (!ret)
 665                 s5k6aa->apply_crop = 0;
 666
 667         return ret;
 668 }
 669
 670 /**
 671  * s5k6aa_configure_video_bus - configure the video output interface
 672  * @bus_type: video bus type: parallel or MIPI-CSI
 673  * @nlanes: number of MIPI lanes to be used (MIPI-CSI only)
 674  *
 675  * Note: Only parallel bus operation has been tested.
 676  */
 677 static int s5k6aa_configure_video_bus(struct s5k6aa *s5k6aa,
 678                                       enum v4l2_mbus_type bus_type, int nlanes)
 679 {
 680         struct i2c_client *client = v4l2_get_subdevdata(&s5k6aa->sd);
 681         u16 cfg = 0;
 682         int ret;
 683
 684         /*
 685          * TODO: The sensor is supposed to support BT.601 and BT.656
 686          * but there is nothing indicating how to switch between both
 687          * in the datasheet. For now default BT.601 interface is assumed.
 688          */
 689         if (bus_type == V4L2_MBUS_CSI2)
 690                 cfg = nlanes;
 691         else if (bus_type != V4L2_MBUS_PARALLEL)
 692                 return -EINVAL;
 693
 694         ret = s5k6aa_write(client, REG_OIF_EN_MIPI_LANES, cfg);
 695         if (ret)
 696                 return ret;
 697         return s5k6aa_write(client, REG_OIF_CFG_CHG, 1);
 698 }
 699
 700 /* This function should be called when switching to new user configuration set*/
 701 static int s5k6aa_new_config_sync(struct i2c_client *client, int timeout,
 702                                   int cid)
 703 {
 704         unsigned long end = jiffies + msecs_to_jiffies(timeout);
 705         u16 reg = 1;
 706         int ret;
 707
 708         ret = s5k6aa_write(client, REG_G_ACTIVE_PREV_CFG, cid);
 709         if (!ret)
 710                 ret = s5k6aa_write(client, REG_G_PREV_CFG_CHG, 1);
 711         if (!ret)
 712                 ret = s5k6aa_write(client, REG_G_NEW_CFG_SYNC, 1);
 713         if (timeout == 0)
 714                 return ret;
 715
 716         while (ret >= 0 && time_is_after_jiffies(end)) {
 717                 ret = s5k6aa_read(client, REG_G_NEW_CFG_SYNC, &reg);
 718                 if (!reg)
 719                         return 0;
 720                 usleep_range(1000, 5000);
 721         }
 722         return ret ? ret : -ETIMEDOUT;
 723 }
 724
 725 /**
 726  * s5k6aa_set_prev_config - write user preview register set
 727  *
 728  * Configure output resolution and color fromat, pixel clock
 729  * frequency range, device frame rate type and frame period range.
 730  */
 731 static int s5k6aa_set_prev_config(struct s5k6aa *s5k6aa,
 732                                   struct s5k6aa_preset *preset)
 733 {
 734         struct i2c_client *client = v4l2_get_subdevdata(&s5k6aa->sd);
 735         int idx = preset->index;
 736         u16 frame_rate_q;
 737         int ret;
 738
 739         if (s5k6aa->fiv->reg_fr_time >= S5K6AA_MAX_HIGHRES_FR_TIME)
 740                 frame_rate_q = FR_RATE_Q_BEST_FRRATE;
 741         else
 742                 frame_rate_q = FR_RATE_Q_BEST_QUALITY;
 743
 744         ret = s5k6aa_set_output_framefmt(s5k6aa, preset);
 745         if (!ret)
 746                 ret = s5k6aa_write(client, REG_P_MAX_OUT_RATE(idx),
 747                                    s5k6aa->pclk_fmax);
 748         if (!ret)
 749                 ret = s5k6aa_write(client, REG_P_MIN_OUT_RATE(idx),
 750                                    s5k6aa->pclk_fmin);
 751         if (!ret)
 752                 ret = s5k6aa_write(client, REG_P_CLK_INDEX(idx),
 753                                    preset->clk_id);
 754         if (!ret)
 755                 ret = s5k6aa_write(client, REG_P_FR_RATE_TYPE(idx),
 756                                    FR_RATE_DYNAMIC);
 757         if (!ret)
 758                 ret = s5k6aa_write(client, REG_P_FR_RATE_Q_TYPE(idx),
 759                                    frame_rate_q);
 760         if (!ret)
 761                 ret = s5k6aa_write(client, REG_P_MAX_FR_TIME(idx),
 762                                    s5k6aa->fiv->reg_fr_time + 33);
 763         if (!ret)
 764                 ret = s5k6aa_write(client, REG_P_MIN_FR_TIME(idx),
 765                                    s5k6aa->fiv->reg_fr_time - 33);
 766         if (!ret)
 767                 ret = s5k6aa_new_config_sync(client, 250, idx);
 768         if (!ret)
 769                 ret = s5k6aa_preview_config_status(client);
 770         if (!ret)
 771                 s5k6aa->apply_cfg = 0;
 772
 773         v4l2_dbg(1, debug, client, "Frame interval: %d +/- 3.3ms. (%d)\n",
 774                  s5k6aa->fiv->reg_fr_time, ret);
 775         return ret;
 776 }
 777
 778 /**
 779  * s5k6aa_initialize_isp - basic ISP MCU initialization
 780  *
 781  * Configure AHB addresses for registers read/write; configure PLLs for
 782  * required output pixel clock. The ISP power supply needs to be already
 783  * enabled, with an optional H/W reset.
 784  * Locking: called with s5k6aa.lock mutex held.
 785  */
 786 static int s5k6aa_initialize_isp(struct v4l2_subdev *sd)
 787 {
 788         struct i2c_client *client = v4l2_get_subdevdata(sd);
 789         struct s5k6aa *s5k6aa = to_s5k6aa(sd);
 790         int ret;
 791
 792         s5k6aa->apply_crop = 1;
 793         s5k6aa->apply_cfg = 1;
 794         msleep(100);
 795
 796         ret = s5k6aa_set_ahb_address(client);
 797         if (ret)
 798                 return ret;
 799         ret = s5k6aa_configure_video_bus(s5k6aa, s5k6aa->bus_type,
 800                                          s5k6aa->mipi_lanes);
 801         if (ret)
 802                 return ret;
 803         ret = s5k6aa_write_array(sd, s5k6aa_analog_config);
 804         if (ret)
 805                 return ret;
 806         msleep(20);
 807
 808         return s5k6aa_configure_pixel_clocks(s5k6aa);
 809 }
 810
 811 static int s5k6aa_gpio_set_value(struct s5k6aa *priv, int id, u32 val)
 812 {
 813         if (!gpio_is_valid(priv->gpio[id].gpio))
 814                 return 0;
 815         gpio_set_value(priv->gpio[id].gpio, !!val);
 816         return 1;
 817 }
 818
 819 static int s5k6aa_gpio_assert(struct s5k6aa *priv, int id)
 820 {
 821         return s5k6aa_gpio_set_value(priv, id, priv->gpio[id].level);
 822 }
 823
 824 static int s5k6aa_gpio_deassert(struct s5k6aa *priv, int id)
 825 {
 826         return s5k6aa_gpio_set_value(priv, id, !priv->gpio[id].level);
 827 }
 828
 829 static int __s5k6aa_power_on(struct s5k6aa *s5k6aa)
 830 {
 831         int ret;
 832
 833         ret = regulator_bulk_enable(S5K6AA_NUM_SUPPLIES, s5k6aa->supplies);
 834         if (ret)
 835                 return ret;
 836         if (s5k6aa_gpio_deassert(s5k6aa, STBY))
 837                 usleep_range(150, 200);
 838
 839         if (s5k6aa->s_power)
 840                 ret = s5k6aa->s_power(1);
 841         usleep_range(4000, 4000);
 842
 843         if (s5k6aa_gpio_deassert(s5k6aa, RST))
 844                 msleep(20);
 845
 846         return ret;
 847 }
 848
 849 static int __s5k6aa_power_off(struct s5k6aa *s5k6aa)
 850 {
 851         int ret;
 852
 853         if (s5k6aa_gpio_assert(s5k6aa, RST))
 854                 usleep_range(100, 150);
 855
 856         if (s5k6aa->s_power) {
 857                 ret = s5k6aa->s_power(0);
 858                 if (ret)
 859                         return ret;
 860         }
 861         if (s5k6aa_gpio_assert(s5k6aa, STBY))
 862                 usleep_range(50, 100);
 863         s5k6aa->streaming = 0;
 864
 865         return regulator_bulk_disable(S5K6AA_NUM_SUPPLIES, s5k6aa->supplies);
 866 }
 867
 868 /*
 869  * V4L2 subdev core and video operations
 870  */
 871 static int s5k6aa_set_power(struct v4l2_subdev *sd, int on)
 872 {
 873         struct s5k6aa *s5k6aa = to_s5k6aa(sd);
 874         int ret = 0;
 875
 876         mutex_lock(&s5k6aa->lock);
 877
 878         if (!on == s5k6aa->power) {
 879                 if (on) {
 880                         ret = __s5k6aa_power_on(s5k6aa);
 881                         if (!ret)
 882                                 ret = s5k6aa_initialize_isp(sd);
 883                 } else {
 884                         ret = __s5k6aa_power_off(s5k6aa);
 885                 }
 886
 887                 if (!ret)
 888                         s5k6aa->power += on ? 1 : -1;
 889         }
 890
 891         mutex_unlock(&s5k6aa->lock);
 892
 893         if (!on || ret || s5k6aa->power != 1)
 894                 return ret;
 895
 896         return v4l2_ctrl_handler_setup(sd->ctrl_handler);
 897 }
 898
 899 static int __s5k6aa_stream(struct s5k6aa *s5k6aa, int enable)
 900 {
 901         struct i2c_client *client = v4l2_get_subdevdata(&s5k6aa->sd);
 902         int ret = 0;
 903
 904         ret = s5k6aa_write(client, REG_G_ENABLE_PREV, enable);
 905         if (!ret)
 906                 ret = s5k6aa_write(client, REG_G_ENABLE_PREV_CHG, 1);
 907         if (!ret)
 908                 s5k6aa->streaming = enable;
 909
 910         return ret;
 911 }
 912
 913 static int s5k6aa_s_stream(struct v4l2_subdev *sd, int on)
 914 {
 915         struct s5k6aa *s5k6aa = to_s5k6aa(sd);
 916         int ret = 0;
 917
 918         mutex_lock(&s5k6aa->lock);
 919
 920         if (s5k6aa->streaming == !on) {
 921                 if (!ret && s5k6aa->apply_cfg)
 922                         ret = s5k6aa_set_prev_config(s5k6aa, s5k6aa->preset);
 923                 if (s5k6aa->apply_crop)
 924                         ret = s5k6aa_set_input_params(s5k6aa);
 925                 if (!ret)
 926                         ret = __s5k6aa_stream(s5k6aa, !!on);
 927         }
 928         mutex_unlock(&s5k6aa->lock);
 929
 930         return ret;
 931 }
 932
 933 static int s5k6aa_g_frame_interval(struct v4l2_subdev *sd,
 934                                    struct v4l2_subdev_frame_interval *fi)
 935 {
 936         struct s5k6aa *s5k6aa = to_s5k6aa(sd);
 937
 938         mutex_lock(&s5k6aa->lock);
 939         fi->interval = s5k6aa->fiv->interval;
 940         mutex_unlock(&s5k6aa->lock);
 941
 942         return 0;
 943 }
 944
 945 static int __s5k6aa_set_frame_interval(struct s5k6aa *s5k6aa,
 946                                        struct v4l2_subdev_frame_interval *fi)
 947 {
 948         struct v4l2_mbus_framefmt *mbus_fmt = &s5k6aa->preset->mbus_fmt;
 949         const struct s5k6aa_interval *fiv = &s5k6aa_intervals[0];
 950         unsigned int err, min_err = UINT_MAX;
 951         unsigned int i, fr_time;
 952
 953         if (fi->interval.denominator == 0)
 954                 return -EINVAL;
 955
 956         fr_time = fi->interval.numerator * 10000 / fi->interval.denominator;
 957
 958         for (i = 0; i < ARRAY_SIZE(s5k6aa_intervals); i++) {
 959                 const struct s5k6aa_interval *iv = &s5k6aa_intervals[i];
 960
 961                 if (mbus_fmt->width > iv->size.width ||
 962                     mbus_fmt->height > iv->size.height)
 963                         continue;
 964
 965                 err = abs(iv->reg_fr_time - fr_time);
 966                 if (err < min_err) {
 967                         fiv = iv;
 968                         min_err = err;
 969                 }
 970         }
 971         s5k6aa->fiv = fiv;
 972
 973         v4l2_dbg(1, debug, &s5k6aa->sd, "Changed frame interval to %d us\n",
 974                  fiv->reg_fr_time * 100);
 975         return 0;
 976 }
 977
 978 static int s5k6aa_s_frame_interval(struct v4l2_subdev *sd,
 979                                    struct v4l2_subdev_frame_interval *fi)
 980 {
 981         struct s5k6aa *s5k6aa = to_s5k6aa(sd);
 982         int ret;
 983
 984         v4l2_dbg(1, debug, sd, "Setting %d/%d frame interval\n",
 985                  fi->interval.numerator, fi->interval.denominator);
 986
 987         mutex_lock(&s5k6aa->lock);
 988         ret = __s5k6aa_set_frame_interval(s5k6aa, fi);
 989         s5k6aa->apply_cfg = 1;
 990
 991         mutex_unlock(&s5k6aa->lock);
 992         return ret;
 993 }
 994
 995 /*
 996  * V4L2 subdev pad level and video operations
 997  */
 998 static int s5k6aa_enum_frame_interval(struct v4l2_subdev *sd,
 999                               struct v4l2_subdev_fh *fh,
1000                               struct v4l2_subdev_frame_interval_enum *fie)
1001 {
1002         struct s5k6aa *s5k6aa = to_s5k6aa(sd);
1003         const struct s5k6aa_interval *fi;
1004         int ret = 0;
1005
1006         if (fie->index > ARRAY_SIZE(s5k6aa_intervals))
1007                 return -EINVAL;
1008
1009         v4l_bound_align_image(&fie->width, S5K6AA_WIN_WIDTH_MIN,
1010                               S5K6AA_WIN_WIDTH_MAX, 1,
1011                               &fie->height, S5K6AA_WIN_HEIGHT_MIN,
1012                               S5K6AA_WIN_HEIGHT_MAX, 1, 0);
1013
1014         mutex_lock(&s5k6aa->lock);
1015         fi = &s5k6aa_intervals[fie->index];
1016         if (fie->width > fi->size.width || fie->height > fi->size.height)
1017                 ret = -EINVAL;
1018         else
1019                 fie->interval = fi->interval;
1020         mutex_unlock(&s5k6aa->lock);
1021
1022         return ret;
1023 }
1024
1025 static int s5k6aa_enum_mbus_code(struct v4l2_subdev *sd,
1026                                  struct v4l2_subdev_fh *fh,
1027                                  struct v4l2_subdev_mbus_code_enum *code)
1028 {
1029         if (code->index >= ARRAY_SIZE(s5k6aa_formats))
1030                 return -EINVAL;
1031
1032         code->code = s5k6aa_formats[code->index].code;
1033         return 0;
1034 }
1035
1036 static int s5k6aa_enum_frame_size(struct v4l2_subdev *sd,
1037                                   struct v4l2_subdev_fh *fh,
1038                                   struct v4l2_subdev_frame_size_enum *fse)
1039 {
1040         int i = ARRAY_SIZE(s5k6aa_formats);
1041
1042         if (fse->index > 0)
1043                 return -EINVAL;
1044
1045         while (--i)
1046                 if (fse->code == s5k6aa_formats[i].code)
1047                         break;
1048
1049         fse->code = s5k6aa_formats[i].code;
1050         fse->min_width  = S5K6AA_WIN_WIDTH_MIN;
1051         fse->max_width  = S5K6AA_WIN_WIDTH_MAX;
1052         fse->max_height = S5K6AA_WIN_HEIGHT_MIN;
1053         fse->min_height = S5K6AA_WIN_HEIGHT_MAX;
1054
1055         return 0;
1056 }
1057
1058 static struct v4l2_rect *
1059 __s5k6aa_get_crop_rect(struct s5k6aa *s5k6aa, struct v4l2_subdev_fh *fh,
1060                        enum v4l2_subdev_format_whence which)
1061 {
1062         if (which == V4L2_SUBDEV_FORMAT_ACTIVE)
1063                 return &s5k6aa->ccd_rect;
1064
1065         WARN_ON(which != V4L2_SUBDEV_FORMAT_TRY);
1066         return v4l2_subdev_get_try_crop(fh, 0);
1067 }
1068
1069 static void s5k6aa_try_format(struct s5k6aa *s5k6aa,
1070                               struct v4l2_mbus_framefmt *mf)
1071 {
1072         unsigned int index;
1073
1074         v4l_bound_align_image(&mf->width, S5K6AA_WIN_WIDTH_MIN,
1075                               S5K6AA_WIN_WIDTH_MAX, 1,
1076                               &mf->height, S5K6AA_WIN_HEIGHT_MIN,
1077                               S5K6AA_WIN_HEIGHT_MAX, 1, 0);
1078
1079         if (mf->colorspace != V4L2_COLORSPACE_JPEG &&
1080             mf->colorspace != V4L2_COLORSPACE_REC709)
1081                 mf->colorspace = V4L2_COLORSPACE_JPEG;
1082
1083         index = s5k6aa_get_pixfmt_index(s5k6aa, mf);
1084
1085         mf->colorspace  = s5k6aa_formats[index].colorspace;
1086         mf->code        = s5k6aa_formats[index].code;
1087         mf->field       = V4L2_FIELD_NONE;
1088 }
1089
1090 static int s5k6aa_get_fmt(struct v4l2_subdev *sd, struct v4l2_subdev_fh *fh,
1091                           struct v4l2_subdev_format *fmt)
1092 {
1093         struct s5k6aa *s5k6aa = to_s5k6aa(sd);
1094         struct v4l2_mbus_framefmt *mf;
1095
1096         memset(fmt->reserved, 0, sizeof(fmt->reserved));
1097
1098         if (fmt->which == V4L2_SUBDEV_FORMAT_TRY) {
1099                 mf = v4l2_subdev_get_try_format(fh, 0);
1100                 fmt->format = *mf;
1101                 return 0;
1102         }
1103
1104         mutex_lock(&s5k6aa->lock);
1105         fmt->format = s5k6aa->preset->mbus_fmt;
1106         mutex_unlock(&s5k6aa->lock);
1107
1108         return 0;
1109 }
1110
1111 static int s5k6aa_set_fmt(struct v4l2_subdev *sd, struct v4l2_subdev_fh *fh,
1112                           struct v4l2_subdev_format *fmt)
1113 {
1114         struct s5k6aa *s5k6aa = to_s5k6aa(sd);
1115         struct s5k6aa_preset *preset = s5k6aa->preset;
1116         struct v4l2_mbus_framefmt *mf;
1117         struct v4l2_rect *crop;
1118         int ret = 0;
1119
1120         mutex_lock(&s5k6aa->lock);
1121         s5k6aa_try_format(s5k6aa, &fmt->format);
1122
1123         if (fmt->which == V4L2_SUBDEV_FORMAT_TRY) {
1124                 mf = v4l2_subdev_get_try_format(fh, fmt->pad);
1125                 crop = v4l2_subdev_get_try_crop(fh, 0);
1126         } else {
1127                 if (s5k6aa->streaming) {
1128                         ret = -EBUSY;
1129                 } else {
1130                         mf = &preset->mbus_fmt;
1131                         crop = &s5k6aa->ccd_rect;
1132                         s5k6aa->apply_cfg = 1;
1133                 }
1134         }
1135
1136         if (ret == 0) {
1137                 struct v4l2_subdev_frame_interval fiv = {
1138                         .interval = {0, 1}
1139                 };
1140
1141                 *mf = fmt->format;
1142                 /*
1143                  * Make sure the crop window is valid, i.e. its size is
1144                  * greater than the output window, as the ISP supports
1145                  * only down-scaling.
1146                  */
1147                 crop->width = clamp_t(unsigned int, crop->width, mf->width,
1148                                       S5K6AA_WIN_WIDTH_MAX);
1149                 crop->height = clamp_t(unsigned int, crop->height, mf->height,
1150                                        S5K6AA_WIN_HEIGHT_MAX);
1151                 crop->left = clamp_t(unsigned int, crop->left, 0,
1152                                      S5K6AA_WIN_WIDTH_MAX - crop->width);
1153                 crop->top  = clamp_t(unsigned int, crop->top, 0,
1154                                      S5K6AA_WIN_HEIGHT_MAX - crop->height);
1155
1156                 /* Reset to minimum possible frame interval */
1157                 ret = __s5k6aa_set_frame_interval(s5k6aa, &fiv);
1158         }
1159         mutex_unlock(&s5k6aa->lock);
1160
1161         return ret;
1162 }
1163
1164 static int s5k6aa_get_crop(struct v4l2_subdev *sd, struct v4l2_subdev_fh *fh,
1165                            struct v4l2_subdev_crop *crop)
1166 {
1167         struct s5k6aa *s5k6aa = to_s5k6aa(sd);
1168         struct v4l2_rect *rect;
1169
1170         memset(crop->reserved, 0, sizeof(crop->reserved));
1171
1172         mutex_lock(&s5k6aa->lock);
1173         rect = __s5k6aa_get_crop_rect(s5k6aa, fh, crop->which);
1174         crop->rect = *rect;
1175         mutex_unlock(&s5k6aa->lock);
1176
1177         v4l2_dbg(1, debug, sd, "Current crop rectangle: (%d,%d)/%dx%d\n",
1178                  rect->left, rect->top, rect->width, rect->height);
1179
1180         return 0;
1181 }
1182
1183 static int s5k6aa_set_crop(struct v4l2_subdev *sd, struct v4l2_subdev_fh *fh,
1184                            struct v4l2_subdev_crop *crop)
1185 {
1186         struct s5k6aa *s5k6aa = to_s5k6aa(sd);
1187         struct v4l2_mbus_framefmt *mf;
1188         unsigned int max_x, max_y;
1189         struct v4l2_rect *crop_r;
1190
1191         mutex_lock(&s5k6aa->lock);
1192         crop_r = __s5k6aa_get_crop_rect(s5k6aa, fh, crop->which);
1193
1194         if (crop->which == V4L2_SUBDEV_FORMAT_ACTIVE) {
1195                 mf = &s5k6aa->preset->mbus_fmt;
1196                 s5k6aa->apply_crop = 1;
1197         } else {
1198                 mf = v4l2_subdev_get_try_format(fh, 0);
1199         }
1200         v4l_bound_align_image(&crop->rect.width, mf->width,
1201                               S5K6AA_WIN_WIDTH_MAX, 1,
1202                               &crop->rect.height, mf->height,
1203                               S5K6AA_WIN_HEIGHT_MAX, 1, 0);
1204
1205         max_x = (S5K6AA_WIN_WIDTH_MAX - crop->rect.width) & ~1;
1206         max_y = (S5K6AA_WIN_HEIGHT_MAX - crop->rect.height) & ~1;
1207
1208         crop->rect.left = clamp_t(unsigned int, crop->rect.left, 0, max_x);
1209         crop->rect.top  = clamp_t(unsigned int, crop->rect.top, 0, max_y);
1210
1211         *crop_r = crop->rect;
1212
1213         mutex_unlock(&s5k6aa->lock);
1214
1215         v4l2_dbg(1, debug, sd, "Set crop rectangle: (%d,%d)/%dx%d\n",
1216                  crop_r->left, crop_r->top, crop_r->width, crop_r->height);
1217
1218         return 0;
1219 }
1220
1221 static const struct v4l2_subdev_pad_ops s5k6aa_pad_ops = {
1222         .enum_mbus_code         = s5k6aa_enum_mbus_code,
1223         .enum_frame_size        = s5k6aa_enum_frame_size,
1224         .enum_frame_interval    = s5k6aa_enum_frame_interval,
1225         .get_fmt                = s5k6aa_get_fmt,
1226         .set_fmt                = s5k6aa_set_fmt,
1227         .get_crop               = s5k6aa_get_crop,
1228         .set_crop               = s5k6aa_set_crop,
1229 };
1230
1231 static const struct v4l2_subdev_video_ops s5k6aa_video_ops = {
1232         .g_frame_interval       = s5k6aa_g_frame_interval,
1233         .s_frame_interval       = s5k6aa_s_frame_interval,
1234         .s_stream               = s5k6aa_s_stream,
1235 };
1236
1237 /*
1238  * V4L2 subdev controls
1239  */
1240
1241 static int s5k6aa_s_ctrl(struct v4l2_ctrl *ctrl)
1242 {
1243         struct v4l2_subdev *sd = ctrl_to_sd(ctrl);
1244         struct i2c_client *client = v4l2_get_subdevdata(sd);
1245         struct s5k6aa *s5k6aa = to_s5k6aa(sd);
1246         int idx, err = 0;
1247
1248         v4l2_dbg(1, debug, sd, "ctrl: 0x%x, value: %d\n", ctrl->id, ctrl->val);
1249
1250         mutex_lock(&s5k6aa->lock);
1251         /*
1252          * If the device is not powered up by the host driver do
1253          * not apply any controls to H/W at this time. Instead
1254          * the controls will be restored right after power-up.
1255          */
1256         if (s5k6aa->power == 0)
1257                 goto unlock;
1258         idx = s5k6aa->preset->index;
1259
1260         switch (ctrl->id) {
1261         case V4L2_CID_AUTO_WHITE_BALANCE:
1262                 err = s5k6aa_set_awb(s5k6aa, ctrl->val);
1263                 break;
1264
1265         case V4L2_CID_BRIGHTNESS:
1266                 err = s5k6aa_write(client, REG_USER_BRIGHTNESS, ctrl->val);
1267                 break;
1268
1269         case V4L2_CID_COLORFX:
1270                 err = s5k6aa_set_colorfx(s5k6aa, ctrl->val);
1271                 break;
1272
1273         case V4L2_CID_CONTRAST:
1274                 err = s5k6aa_write(client, REG_USER_CONTRAST, ctrl->val);
1275                 break;
1276
1277         case V4L2_CID_EXPOSURE_AUTO:
1278                 err = s5k6aa_set_auto_exposure(s5k6aa, ctrl->val);
1279                 break;
1280
1281         case V4L2_CID_HFLIP:
1282                 err = s5k6aa_set_mirror(s5k6aa, ctrl->val);
1283                 if (err)
1284                         break;
1285                 err = s5k6aa_write(client, REG_G_PREV_CFG_CHG, 1);
1286                 break;
1287
1288         case V4L2_CID_POWER_LINE_FREQUENCY:
1289                 err = s5k6aa_set_anti_flicker(s5k6aa, ctrl->val);
1290                 break;
1291
1292         case V4L2_CID_SATURATION:
1293                 err = s5k6aa_write(client, REG_USER_SATURATION, ctrl->val);
1294                 break;
1295
1296         case V4L2_CID_SHARPNESS:
1297                 err = s5k6aa_write(client, REG_USER_SHARPBLUR, ctrl->val);
1298                 break;
1299
1300         case V4L2_CID_WHITE_BALANCE_TEMPERATURE:
1301                 err = s5k6aa_write(client, REG_P_COLORTEMP(idx), ctrl->val);
1302                 if (err)
1303                         break;
1304                 err = s5k6aa_write(client, REG_G_PREV_CFG_CHG, 1);
1305                 break;
1306         }
1307 unlock:
1308         mutex_unlock(&s5k6aa->lock);
1309         return err;
1310 }
1311
1312 static const struct v4l2_ctrl_ops s5k6aa_ctrl_ops = {
1313         .s_ctrl = s5k6aa_s_ctrl,
1314 };
1315
1316 static int s5k6aa_log_status(struct v4l2_subdev *sd)
1317 {
1318         v4l2_ctrl_handler_log_status(sd->ctrl_handler, sd->name);
1319         return 0;
1320 }
1321
1322 #define V4L2_CID_RED_GAIN       (V4L2_CTRL_CLASS_CAMERA | 0x1001)
1323 #define V4L2_CID_GREEN_GAIN     (V4L2_CTRL_CLASS_CAMERA | 0x1002)
1324 #define V4L2_CID_BLUE_GAIN      (V4L2_CTRL_CLASS_CAMERA | 0x1003)
1325
1326 static const struct v4l2_ctrl_config s5k6aa_ctrls[] = {
1327         {
1328                 .ops    = &s5k6aa_ctrl_ops,
1329                 .id     = V4L2_CID_RED_GAIN,
1330                 .type   = V4L2_CTRL_TYPE_INTEGER,
1331                 .name   = "Gain, Red",
1332                 .min    = 0,
1333                 .max    = 256,
1334                 .def    = 127,
1335                 .step   = 1,
1336         }, {
1337                 .ops    = &s5k6aa_ctrl_ops,
1338                 .id     = V4L2_CID_GREEN_GAIN,
1339                 .type   = V4L2_CTRL_TYPE_INTEGER,
1340                 .name   = "Gain, Green",
1341                 .min    = 0,
1342                 .max    = 256,
1343                 .def    = 127,
1344                 .step   = 1,
1345         }, {
1346                 .ops    = &s5k6aa_ctrl_ops,
1347                 .id     = V4L2_CID_BLUE_GAIN,
1348                 .type   = V4L2_CTRL_TYPE_INTEGER,
1349                 .name   = "Gain, Blue",
1350                 .min    = 0,
1351                 .max    = 256,
1352                 .def    = 127,
1353                 .step   = 1,
1354         },
1355 };
1356
1357 static int s5k6aa_initialize_ctrls(struct s5k6aa *s5k6aa)
1358 {
1359         const struct v4l2_ctrl_ops *ops = &s5k6aa_ctrl_ops;
1360         struct s5k6aa_ctrls *ctrls = &s5k6aa->ctrls;
1361         struct v4l2_ctrl_handler *hdl = &ctrls->handler;
1362
1363         int ret = v4l2_ctrl_handler_init(hdl, 16);
1364         if (ret)
1365                 return ret;
1366         /* Auto white balance cluster */
1367         ctrls->awb = v4l2_ctrl_new_std(hdl, ops, V4L2_CID_AUTO_WHITE_BALANCE,
1368                                        0, 1, 1, 1);
1369         ctrls->gain_red = v4l2_ctrl_new_custom(hdl, &s5k6aa_ctrls[0], NULL);
1370         ctrls->gain_green = v4l2_ctrl_new_custom(hdl, &s5k6aa_ctrls[1], NULL);
1371         ctrls->gain_blue = v4l2_ctrl_new_custom(hdl, &s5k6aa_ctrls[2], NULL);
1372         v4l2_ctrl_auto_cluster(4, &ctrls->awb, 0, false);
1373
1374         ctrls->hflip = v4l2_ctrl_new_std(hdl, ops, V4L2_CID_HFLIP, 0, 1, 1, 0);
1375         ctrls->vflip = v4l2_ctrl_new_std(hdl, ops, V4L2_CID_VFLIP, 0, 1, 1, 0);
1376         v4l2_ctrl_cluster(2, &ctrls->hflip);
1377
1378         ctrls->auto_exp = v4l2_ctrl_new_std_menu(hdl, ops,
1379                                 V4L2_CID_EXPOSURE_AUTO,
1380                                 V4L2_EXPOSURE_MANUAL, 0, V4L2_EXPOSURE_AUTO);
1381         /* Exposure time: x 1 us */
1382         ctrls->exposure = v4l2_ctrl_new_std(hdl, ops, V4L2_CID_EXPOSURE,
1383                                             0, 6000000U, 1, 100000U);
1384         /* Total gain: 256 <=> 1x */
1385         ctrls->gain = v4l2_ctrl_new_std(hdl, ops, V4L2_CID_GAIN,
1386                                         0, 256, 1, 256);
1387         v4l2_ctrl_auto_cluster(3, &ctrls->auto_exp, 0, false);
1388
1389         v4l2_ctrl_new_std_menu(hdl, ops, V4L2_CID_POWER_LINE_FREQUENCY,
1390                                V4L2_CID_POWER_LINE_FREQUENCY_AUTO, 0,
1391                                V4L2_CID_POWER_LINE_FREQUENCY_AUTO);
1392
1393         v4l2_ctrl_new_std_menu(hdl, ops, V4L2_CID_COLORFX,
1394                                V4L2_COLORFX_SKY_BLUE, ~0x6f, V4L2_COLORFX_NONE);
1395
1396         v4l2_ctrl_new_std(hdl, ops, V4L2_CID_WHITE_BALANCE_TEMPERATURE,
1397                           0, 256, 1, 0);
1398
1399         v4l2_ctrl_new_std(hdl, ops, V4L2_CID_SATURATION, -127, 127, 1, 0);
1400         v4l2_ctrl_new_std(hdl, ops, V4L2_CID_BRIGHTNESS, -127, 127, 1, 0);
1401         v4l2_ctrl_new_std(hdl, ops, V4L2_CID_CONTRAST, -127, 127, 1, 0);
1402         v4l2_ctrl_new_std(hdl, ops, V4L2_CID_SHARPNESS, -127, 127, 1, 0);
1403
1404         if (hdl->error) {
1405                 ret = hdl->error;
1406                 v4l2_ctrl_handler_free(hdl);
1407                 return ret;
1408         }
1409
1410         s5k6aa->sd.ctrl_handler = hdl;
1411         return 0;
1412 }
1413
1414 /*
1415  * V4L2 subdev internal operations
1416  */
1417 static int s5k6aa_open(struct v4l2_subdev *sd, struct v4l2_subdev_fh *fh)
1418 {
1419         struct v4l2_mbus_framefmt *format = v4l2_subdev_get_try_format(fh, 0);
1420         struct v4l2_rect *crop = v4l2_subdev_get_try_crop(fh, 0);
1421
1422         format->colorspace = s5k6aa_formats[0].colorspace;
1423         format->code = s5k6aa_formats[0].code;
1424         format->width = S5K6AA_OUT_WIDTH_DEF;
1425         format->height = S5K6AA_OUT_HEIGHT_DEF;
1426         format->field = V4L2_FIELD_NONE;
1427
1428         crop->width = S5K6AA_WIN_WIDTH_MAX;
1429         crop->height = S5K6AA_WIN_HEIGHT_MAX;
1430         crop->left = 0;
1431         crop->top = 0;
1432
1433         return 0;
1434 }
1435
1436 static int s5k6aa_check_fw_revision(struct s5k6aa *s5k6aa)
1437 {
1438         struct i2c_client *client = v4l2_get_subdevdata(&s5k6aa->sd);
1439         u16 api_ver = 0, fw_rev = 0;
1440
1441         int ret = s5k6aa_set_ahb_address(client);
1442
1443         if (!ret)
1444                 ret = s5k6aa_read(client, REG_FW_APIVER, &api_ver);
1445         if (!ret)
1446                 ret = s5k6aa_read(client, REG_FW_REVISION, &fw_rev);
1447         if (ret) {
1448                 v4l2_err(&s5k6aa->sd, "FW revision check failed!\n");
1449                 return ret;
1450         }
1451
1452         v4l2_info(&s5k6aa->sd, "FW API ver.: 0x%X, FW rev.: 0x%X\n",
1453                   api_ver, fw_rev);
1454
1455         return api_ver == S5K6AAFX_FW_APIVER ? 0 : -ENODEV;
1456 }
1457
1458 static int s5k6aa_registered(struct v4l2_subdev *sd)
1459 {
1460         struct s5k6aa *s5k6aa = to_s5k6aa(sd);
1461         int ret;
1462
1463         mutex_lock(&s5k6aa->lock);
1464         ret = __s5k6aa_power_on(s5k6aa);
1465         if (!ret) {
1466                 msleep(100);
1467                 ret = s5k6aa_check_fw_revision(s5k6aa);
1468                 __s5k6aa_power_off(s5k6aa);
1469         }
1470         mutex_unlock(&s5k6aa->lock);
1471
1472         return ret;
1473 }
1474
1475 static const struct v4l2_subdev_internal_ops s5k6aa_subdev_internal_ops = {
1476         .registered = s5k6aa_registered,
1477         .open = s5k6aa_open,
1478 };
1479
1480 static const struct v4l2_subdev_core_ops s5k6aa_core_ops = {
1481         .s_power = s5k6aa_set_power,
1482         .log_status = s5k6aa_log_status,
1483 };
1484
1485 static const struct v4l2_subdev_ops s5k6aa_subdev_ops = {
1486         .core = &s5k6aa_core_ops,
1487         .pad = &s5k6aa_pad_ops,
1488         .video = &s5k6aa_video_ops,
1489 };
1490
1491 /*
1492  * GPIO setup
1493  */
1494
1495 static int s5k6aa_configure_gpios(struct s5k6aa *s5k6aa,
1496                                   const struct s5k6aa_platform_data *pdata)
1497 {
1498         struct i2c_client *client = v4l2_get_subdevdata(&s5k6aa->sd);
1499         const struct s5k6aa_gpio *gpio;
1500         unsigned long flags;
1501         int ret;
1502
1503         s5k6aa->gpio[STBY].gpio = -EINVAL;
1504         s5k6aa->gpio[RST].gpio  = -EINVAL;
1505
1506         gpio = &pdata->gpio_stby;
1507         if (gpio_is_valid(gpio->gpio)) {
1508                 flags = (gpio->level ? GPIOF_OUT_INIT_HIGH : GPIOF_OUT_INIT_LOW)
1509                       | GPIOF_EXPORT;
1510                 ret = devm_gpio_request_one(&client->dev, gpio->gpio, flags,
1511                                             "S5K6AA_STBY");
1512                 if (ret < 0)
1513                         return ret;
1514
1515                 s5k6aa->gpio[STBY] = *gpio;
1516         }
1517
1518         gpio = &pdata->gpio_reset;
1519         if (gpio_is_valid(gpio->gpio)) {
1520                 flags = (gpio->level ? GPIOF_OUT_INIT_HIGH : GPIOF_OUT_INIT_LOW)
1521                       | GPIOF_EXPORT;
1522                 ret = devm_gpio_request_one(&client->dev, gpio->gpio, flags,
1523                                             "S5K6AA_RST");
1524                 if (ret < 0)
1525                         return ret;
1526
1527                 s5k6aa->gpio[RST] = *gpio;
1528         }
1529
1530         return 0;
1531 }
1532
1533 static int s5k6aa_probe(struct i2c_client *client,
1534                         const struct i2c_device_id *id)
1535 {
1536         const struct s5k6aa_platform_data *pdata = client->dev.platform_data;
1537         struct v4l2_subdev *sd;
1538         struct s5k6aa *s5k6aa;
1539         int i, ret;
1540
1541         if (pdata == NULL) {
1542                 dev_err(&client->dev, "Platform data not specified\n");
1543                 return -EINVAL;
1544         }
1545
1546         if (pdata->mclk_frequency == 0) {
1547                 dev_err(&client->dev, "MCLK frequency not specified\n");
1548                 return -EINVAL;
1549         }
1550
1551         s5k6aa = devm_kzalloc(&client->dev, sizeof(*s5k6aa), GFP_KERNEL);
1552         if (!s5k6aa)
1553                 return -ENOMEM;
1554
1555         mutex_init(&s5k6aa->lock);
1556
1557         s5k6aa->mclk_frequency = pdata->mclk_frequency;
1558         s5k6aa->bus_type = pdata->bus_type;
1559         s5k6aa->mipi_lanes = pdata->nlanes;
1560         s5k6aa->s_power = pdata->set_power;
1561         s5k6aa->inv_hflip = pdata->horiz_flip;
1562         s5k6aa->inv_vflip = pdata->vert_flip;
1563
1564         sd = &s5k6aa->sd;
1565         v4l2_i2c_subdev_init(sd, client, &s5k6aa_subdev_ops);
1566         strlcpy(sd->name, DRIVER_NAME, sizeof(sd->name));
1567
1568         sd->internal_ops = &s5k6aa_subdev_internal_ops;
1569         sd->flags |= V4L2_SUBDEV_FL_HAS_DEVNODE;
1570
1571         s5k6aa->pad.flags = MEDIA_PAD_FL_SOURCE;
1572         sd->entity.type = MEDIA_ENT_T_V4L2_SUBDEV_SENSOR;
1573         ret = media_entity_init(&sd->entity, 1, &s5k6aa->pad, 0);
1574         if (ret)
1575                 return ret;
1576
1577         ret = s5k6aa_configure_gpios(s5k6aa, pdata);
1578         if (ret)
1579                 goto out_err;
1580
1581         for (i = 0; i < S5K6AA_NUM_SUPPLIES; i++)
1582                 s5k6aa->supplies[i].supply = s5k6aa_supply_names[i];
1583
1584         ret = devm_regulator_bulk_get(&client->dev, S5K6AA_NUM_SUPPLIES,
1585                                  s5k6aa->supplies);
1586         if (ret) {
1587                 dev_err(&client->dev, "Failed to get regulators\n");
1588                 goto out_err;
1589         }
1590
1591         ret = s5k6aa_initialize_ctrls(s5k6aa);
1592         if (ret)
1593                 goto out_err;
1594
1595         s5k6aa_presets_data_init(s5k6aa);
1596
1597         s5k6aa->ccd_rect.width = S5K6AA_WIN_WIDTH_MAX;
1598         s5k6aa->ccd_rect.height = S5K6AA_WIN_HEIGHT_MAX;
1599         s5k6aa->ccd_rect.left = 0;
1600         s5k6aa->ccd_rect.top = 0;
1601
1602         return 0;
1603
1604 out_err:
1605         media_entity_cleanup(&s5k6aa->sd.entity);
1606         return ret;
1607 }
1608
1609 static int s5k6aa_remove(struct i2c_client *client)
1610 {
1611         struct v4l2_subdev *sd = i2c_get_clientdata(client);
1612
1613         v4l2_device_unregister_subdev(sd);
1614         v4l2_ctrl_handler_free(sd->ctrl_handler);
1615         media_entity_cleanup(&sd->entity);
1616
1617         return 0;
1618 }
1619
1620 static const struct i2c_device_id s5k6aa_id[] = {
1621         { DRIVER_NAME, 0 },
1622         { },
1623 };
1624 MODULE_DEVICE_TABLE(i2c, s5k6aa_id);
1625
1626
1627 static struct i2c_driver s5k6aa_i2c_driver = {
1628         .driver = {
1629                 .name = DRIVER_NAME
1630         },
1631         .probe          = s5k6aa_probe,
1632         .remove         = s5k6aa_remove,
1633         .id_table       = s5k6aa_id,
1634 };
1635
1636 module_i2c_driver(s5k6aa_i2c_driver);
1637
1638 MODULE_DESCRIPTION("Samsung S5K6AA(FX) SXGA camera driver");
1639 MODULE_AUTHOR("Sylwester Nawrocki <s.nawrocki@samsung.com>");
1640 MODULE_LICENSE("GPL");