#endif
/*
- * Assember start up done, start code proper.
+ * Assembler start up done, start code proper.
*/
jsr start_kernel /* start Linux kernel */
/***************************************************************************/
/*
- * Some 5272 based boards have the FEC ethernet diectly connected to
+ * Some 5272 based boards have the FEC ethernet directly connected to
* an ethernet switch. In this case we need to use the fixed phy type,
* and we need to declare it early in boot.
*/
/*
* We need to be carefull probing on bus 0 (directly connected to host
- * bridge). We should only acccess the well defined possible devices in
+ * bridge). We should only access the well defined possible devices in
* use, ignore aliases and the like.
*/
static unsigned char mcf_host_slot2sid[32] = {
xdnrm_sd:
mov.l %a1,-(%sp)
tst.b LOCAL_EX(%a0) # is denorm pos or neg?
- smi.b %d1 # set d0 accodingly
+ smi.b %d1 # set d0 accordingly
bsr.l unf_sub
mov.l (%sp)+,%a1
xdnrm_exit:
# routines where an instruction is selected by an index into
# a large jump table corresponding to a given instruction which
# has been decoded. Flow continues here where we now decode
-# further accoding to the source operand type.
+# further according to the source operand type.
#
global fsinh
#
# 1. Branch on the sign of the adjusted exponent.
# 2p.(positive exp)
-# 2. Check M16 and the digits in lwords 2 and 3 in decending order.
+# 2. Check M16 and the digits in lwords 2 and 3 in descending order.
# 3. Add one for each zero encountered until a non-zero digit.
# 4. Subtract the count from the exp.
# 5. Check if the exp has crossed zero in #3 above; make the exp abs
# and set SE.
# 6. Multiply the mantissa by 10**count.
# 2n.(negative exp)
-# 2. Check the digits in lwords 3 and 2 in decending order.
+# 2. Check the digits in lwords 3 and 2 in descending order.
# 3. Add one for each zero encountered until a non-zero digit.
# 4. Add the count to the exp.
# 5. Check if the exp has crossed zero in #3 above; clear SE.
#
# 1. Branch on the sign of the adjusted exponent.
# 2p.(positive exp)
-# 2. Check M16 and the digits in lwords 2 and 3 in decending order.
+# 2. Check M16 and the digits in lwords 2 and 3 in descending order.
# 3. Add one for each zero encountered until a non-zero digit.
# 4. Subtract the count from the exp.
# 5. Check if the exp has crossed zero in #3 above; make the exp abs
# and set SE.
# 6. Multiply the mantissa by 10**count.
# 2n.(negative exp)
-# 2. Check the digits in lwords 3 and 2 in decending order.
+# 2. Check the digits in lwords 3 and 2 in descending order.
# 3. Add one for each zero encountered until a non-zero digit.
# 4. Add the count to the exp.
# 5. Check if the exp has crossed zero in #3 above; clear SE.
* AUG/22/2000 : added support for 32-bit Dual-Address-Mode (K) 2000
* Oliver Kamphenkel (O.Kamphenkel@tu-bs.de)
*
- * AUG/25/2000 : addad support for 8, 16 and 32-bit Single-Address-Mode (K)2000
+ * AUG/25/2000 : added support for 8, 16 and 32-bit Single-Address-Mode (K)2000
* Oliver Kamphenkel (O.Kamphenkel@tu-bs.de)
*
* APR/18/2002 : added proper support for MCF5272 DMA controller.
/*
* I2C module.
*/
-#define MCFI2C_BASE0 (MCF_MBAR + 0x280) /* Base addreess I2C0 */
+#define MCFI2C_BASE0 (MCF_MBAR + 0x280) /* Base address I2C0 */
#define MCFI2C_SIZE0 0x20 /* Register set size */
-#define MCFI2C_BASE1 (MCF_MBAR2 + 0x440) /* Base addreess I2C1 */
+#define MCFI2C_BASE1 (MCF_MBAR2 + 0x440) /* Base address I2C1 */
#define MCFI2C_SIZE1 0x20 /* Register set size */
/*
/*
* MMU Operation register.
*/
-#define MMUOR_UAA 0x00000001 /* Update allocatiom address */
+#define MMUOR_UAA 0x00000001 /* Update allocation address */
#define MMUOR_ACC 0x00000002 /* TLB access */
#define MMUOR_RD 0x00000004 /* TLB access read */
#define MMUOR_WR 0x00000000 /* TLB access write */
/*
* Q40 master Chip Control
- * RTC stuff merged for compactnes..
+ * RTC stuff merged for compactness.
*/
#ifndef _Q40_MASTER_H
*
* The host talks to the IOPs using a rather simple message-passing scheme via
* a shared memory area in the IOP RAM. Each IOP has seven "channels"; each
- * channel is conneced to a specific software driver on the IOP. For example
+ * channel is connected to a specific software driver on the IOP. For example
* on the SCC IOP there is one channel for each serial port. Each channel has
* an incoming and and outgoing message queue with a depth of one.
*
bfextu %d2{#13,#3},%d0
.endm
-| decode the 8bit diplacement from the brief extension word
+| decode the 8bit displacement from the brief extension word
.macro fp_decode_disp8
move.b %d2,%d0
ext.w %d0
projects / karo-tx-linux.git / commitdiff