+++ /dev/null
-<!-- Copyright (C) 2003 Red Hat, Inc. -->
-<!-- This material may be distributed only subject to the terms -->
-<!-- and conditions set forth in the Open Publication License, v1.0 -->
-<!-- or later (the latest version is presently available at -->
-<!-- http://www.opencontent.org/openpub/). -->
-<!-- Distribution of the work or derivative of the work in any -->
-<!-- standard (paper) book form is prohibited unless prior -->
-<!-- permission is obtained from the copyright holder. -->
-<HTML
-><HEAD
-><TITLE
->Cirrus Logic ARM CL-PS7111 Evaluation Board Hardware Setup</TITLE
-><meta name="MSSmartTagsPreventParsing" content="TRUE">
-<META
-NAME="GENERATOR"
-CONTENT="Modular DocBook HTML Stylesheet Version 1.76b+
-"><LINK
-REL="HOME"
-TITLE="eCos User Guide"
-HREF="ecos-user-guide.html"><LINK
-REL="UP"
-TITLE="Target Setup"
-HREF="appendix-target-setup.html"><LINK
-REL="PREVIOUS"
-TITLE="Cirrus Logic ARM EP7209 Development Board Hardware Setup"
-HREF="setup-arm-ep7209.html"><LINK
-REL="NEXT"
-TITLE="StrongARM EBSA-285 Hardware Setup"
-HREF="setup-arm-ebsa285.html"></HEAD
-><BODY
-CLASS="SECT1"
-BGCOLOR="#FFFFFF"
-TEXT="#000000"
-LINK="#0000FF"
-VLINK="#840084"
-ALINK="#0000FF"
-><DIV
-CLASS="NAVHEADER"
-><TABLE
-SUMMARY="Header navigation table"
-WIDTH="100%"
-BORDER="0"
-CELLPADDING="0"
-CELLSPACING="0"
-><TR
-><TH
-COLSPAN="3"
-ALIGN="center"
->eCos User Guide</TH
-></TR
-><TR
-><TD
-WIDTH="10%"
-ALIGN="left"
-VALIGN="bottom"
-><A
-HREF="setup-arm-ep7209.html"
-ACCESSKEY="P"
->Prev</A
-></TD
-><TD
-WIDTH="80%"
-ALIGN="center"
-VALIGN="bottom"
->Appendix A. Target Setup</TD
-><TD
-WIDTH="10%"
-ALIGN="right"
-VALIGN="bottom"
-><A
-HREF="setup-arm-ebsa285.html"
-ACCESSKEY="N"
->Next</A
-></TD
-></TR
-></TABLE
-><HR
-ALIGN="LEFT"
-WIDTH="100%"></DIV
-><DIV
-CLASS="SECT1"
-><H1
-CLASS="SECT1"
-><A
-NAME="SETUP-ARM-CLPS7111">Cirrus Logic ARM CL-PS7111 Evaluation Board Hardware Setup</H1
-><P
->The implementation of the port of eCos to the Cirrus Logic
-ARM CL-PS7111 Evaluation Board (also known as EB7111) is based on
-the EP7211 Development Board port.</P
-><P
->For that reason, the setup required is identical to the EP7211
-Development Board as described above, with the following exceptions:</P
-><P
-></P
-><UL
-><LI
-><P
->The Cygmon ROM monitor is not supported</P
-></LI
-><LI
-><P
->The ARM Multi-ICE is not supported</P
-></LI
-><LI
-><P
->Pre-built GDB stubs are provided in the
-directory loaders/arm-eb7111 relative to the root of your
-eCos installation</P
-></LI
-><LI
-><P
->If rebuilding the GDB stub ROM image, change the "Cirrus
-Logic processor variant" option (CYGHWR_HAL_ARM_EDB7XXX_VARIANT)
-from the EP7211 to the CL_PS7111. This can be selected
-in the
-<SPAN
-CLASS="emphasis"
-><I
-CLASS="EMPHASIS"
->eCos Configuration Tool</I
-></SPAN
->
-, or if using ecosconfig, can be set by uncommenting the user_value
-property of this option in ecos.ecc and setting it to "CL_PS7111"</P
-></LI
-></UL
-><P
->All remote serial communication is done with the serial I/O
-connector</P
-><TABLE
-BORDER="5"
-BGCOLOR="#E0E0F0"
-WIDTH="70%"
-><TR
-><TD
-><PRE
-CLASS="PROGRAMLISTING"
->/misc
-% slow_cat.tcl < [path]/gdb_module.srec > /dev/ttyS0</PRE
-></TD
-></TR
-></TABLE
-><P
->Power off the board, and change it to boot the GDB stubs in
-big-endian mode by setting the switches like this:</P
-><P
->SW1: 00000000 (all levers down)
-SW2: 10001010</P
-><P
->The GDB stubs allow communication with GDB using the serial
-port at connector PJ7A (lower connector). The communication parameters
-are fixed at 38400 baud, 8 data bits, no parity bit and 1 stop
-bit (8-N-1). No flow control is employed. Connection to the host
-computer should be made using a straight through serial cable.</P
-></DIV
-><DIV
-CLASS="NAVFOOTER"
-><HR
-ALIGN="LEFT"
-WIDTH="100%"><TABLE
-SUMMARY="Footer navigation table"
-WIDTH="100%"
-BORDER="0"
-CELLPADDING="0"
-CELLSPACING="0"
-><TR
-><TD
-WIDTH="33%"
-ALIGN="left"
-VALIGN="top"
-><A
-HREF="setup-arm-ep7209.html"
-ACCESSKEY="P"
->Prev</A
-></TD
-><TD
-WIDTH="34%"
-ALIGN="center"
-VALIGN="top"
-><A
-HREF="ecos-user-guide.html"
-ACCESSKEY="H"
->Home</A
-></TD
-><TD
-WIDTH="33%"
-ALIGN="right"
-VALIGN="top"
-><A
-HREF="setup-arm-ebsa285.html"
-ACCESSKEY="N"
->Next</A
-></TD
-></TR
-><TR
-><TD
-WIDTH="33%"
-ALIGN="left"
-VALIGN="top"
->Cirrus Logic ARM EP7209 Development Board Hardware Setup</TD
-><TD
-WIDTH="34%"
-ALIGN="center"
-VALIGN="top"
-><A
-HREF="appendix-target-setup.html"
-ACCESSKEY="U"
->Up</A
-></TD
-><TD
-WIDTH="33%"
-ALIGN="right"
-VALIGN="top"
->StrongARM EBSA-285 Hardware Setup</TD
-></TR
-></TABLE
-></DIV
-></BODY
-></HTML
->
\ No newline at end of file
projects / karo-tx-redboot.git / blobdiff