Currently is_16bit_nand() is a per SoC function and it decides the bus nand
width by reading some boot related registers.
This method works when NAND is the boot medium, but does not work if another
boot medium is used. For example: booting from a SD card and then using NAND
to store the environment variables, would lead to the following error:
NAND bus width 16 instead 8 bit
No NAND device found!!!
0 MiB
Use CONFIG_SYS_NAND_BUSWIDTH_16BIT symbol to decide the bus width.
If it is defined in the board file, then consider 16-bit NAND bus-width,
otherwise assume 8-bit NAND is used.
This also aligns with Documentation/devicetree/bindings/mtd/nand.txt, which
states:
nand-bus-width : 8 or 16 bus width if not present 8
Joe Hershberger [Mon, 8 Apr 2013 10:32:50 +0000 (10:32 +0000)]
mtd: Make mtdparts work with pre-reloc env
The env in UBI needs to look up the mtd partition as part of relocation,
which happens before relocation. Make the mtdparts code capable of
working on the default env to start with.
The code tries to set values in the env as well, but again, the env
isn't there yet, so add a check to setenv to not allow sets before the
env is relocated.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Jon Hunter [Tue, 9 Apr 2013 21:41:32 +0000 (16:41 -0500)]
omap5912-osk: Increase flash partition for u-boot
The current u-boot binary needs more than 128KB of flash space and so
move the u-boot environment from an offset of 128KB to 256KB in flash
to ensure the enviroment does not overlap with u-boot.
Jon Hunter [Tue, 9 Apr 2013 21:41:31 +0000 (16:41 -0500)]
omap5912-osk: Fix device initialisation
In the current u-boot, the device pin multiplexing and clock
initialisation needs to be early during the boot process and before
board_init() is called. U-boot is currently crashing on this board
because this is not being done early enough. Therefore, add a s_init()
function for the omap5912-osk board to do this.
Also fix the stack pointer so that it is pointing to the end of the
internal RAM and not the beginning as this was also causing the device
to crash.
Jon Hunter [Tue, 9 Apr 2013 21:41:30 +0000 (16:41 -0500)]
omap5912-osk: Fix booting from NOR flash
The omap5912-osk board is using a RAM based address as the linker
location for code. This is causing several problems when attempting
to run the latest u-boot code base on this board from flash. Update
the default linker location for code to be in NOR flash at address
0x00000000.
The omap5912-osk board only has 32MB of RAM and so fix the comment
in the omap5912-osk config.mk file as well.
Jon Hunter [Tue, 9 Apr 2013 21:41:29 +0000 (16:41 -0500)]
omap5912-osk: Fix DRAM initialisation
The size of the DRAM for the omap5912-osk board is getting setup in the
dram_init() function. However, for the current u-boot release this is
too late and needs to be done in dram_init_banksize(). Therefore, add
a dram_init_banksize() function for the omap5912-osk board and setup the
DRAM size there.
The omap4460_volts struct was incorrectly referencing tps62361
instead of twl6030 as PMIC for the core and mm voltages (the
tps is used for mpu supply only). This shall lead to bad OPP
settings while booting kernel. Fixing it.
powerpc/lib: fix unsafe register handling in wait_ticks
If watchdog is enabled, the arch/powerpc/lib/ticks.S::wait_ticks() function
calls the function specified by the WATCHDOG_RESET macro.
The wait_ticks function depends on the registers r0, r6 and r7 being
preserved however that is not guaranteed, e.g. if the reset function is a
C function this will probably overwrite r0 and cause an endless loop.
The following patch changes to using r14+r15 instead of r6+r7 (to resemble
what would have been generated by a C compiler) and saves all necessary
registers on the stack.
The patch has been tested on a custom MPC5125 based machine using the 512x
powerpc architecture.
Signed-off-by: Mats Karrman <mats.karrman@tritech.se> Cc: Wolfgang Denk <wd@denx.de> Acked-by: Joakim Tjernlund <joakim.tjernlund@transmode.se> Tested-by: Stefan Roese <sr@denx.de>
ramneek mehresh [Sun, 17 Feb 2013 18:23:32 +0000 (18:23 +0000)]
powerpc/usb: Fix usb device-tree fix-up
Fix USB device-tree fixup to properly handle device-tree fixup and
print appropriate message when wrong/junk "dr_mode" or "phy_type"
are mentioned in hwconfig string
am335x_evm: Enable DFU for NAND and MMC, provide example alt_infos
- Add CONFIG_DFU_NAND, CONFIG_DFU_MMC
- Set dfu_alt_info_nand, dfu_alt_info_emmc and dfu_alt_info_mmc to show
working examples for those cases.
- Increase CONFIG_SYS_MAXARGS due to hush parsing bugs that would
otherwise disallow 'setenv dfu_alt_info ${dfu_alt_info_nand}'.
- Enable CONFIG_FAT_WRITE to allow updating on MMC
Signed-off-by: Pantelis Antoniou <panto@antoniou-consulting.com> Signed-off-by: Tom Rini <trini@ti.com>
Tom Rini [Thu, 14 Mar 2013 05:32:50 +0000 (05:32 +0000)]
nand: Extend nand_(read|write)_skip_bad with *actual and limit parameters
We make these two functions take a size_t pointer to how much space
was used on NAND to read or write the buffer (when reads/writes happen)
so that bad blocks can be accounted for. We also make them take an
loff_t limit on how much data can be read or written. This means that
we can now catch the case of when writing to a partition would exceed
the partition size due to bad blocks. To do this we also need to make
check_skip_len count not just complete blocks used but partial ones as
well. All callers of nand_(read|write)_skip_bad are adjusted to call
these with the most sensible limits available.
The changes were started by Pantelis and finished by Tom.
Signed-off-by: Pantelis Antoniou <panto@antoniou-consulting.com> Signed-off-by: Tom Rini <trini@ti.com>
Previously we didn't support upload/download larger than available
memory. This is pretty bad when you have to update your root filesystem
for example.
This patch removes that limitation (and the crashes when you transfered
any file larger than 4MB) by making raw image writes be done in chunks
and making file maximum size be configurable.
The sequence number is a 16 bit counter; make sure we handle rollover
correctly. This fixes the wrong transfers for large (> 256MB) images.
Also utilize a variable to handle initialization, so that we don't rely
on just the counter sent by the host.
Signed-off-by: Pantelis Antoniou <panto@antoniou-consulting.com> Signed-off-by: Tom Rini <trini@ti.com>
Simon Glass [Tue, 26 Mar 2013 13:09:44 +0000 (13:09 +0000)]
patman: Add Series-process-log tag to sort/uniq change logs
For some series with lots of changes it is annoying that duplicate change
log items are not caught. It is also helpful sometimes to sort the change
logs.
Add a Series-process-log tag to enable this, which can be placed in a
commit to control this.
The change to the Cc: line is to fix a checkpatch warning.
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Doug Anderson <dianders@chromium.org>
Simon Glass [Tue, 26 Mar 2013 13:09:43 +0000 (13:09 +0000)]
patman: Add -a option to refrain from test-applying the patches
Especially with the Linux kernel, it takes a long time (a minute or more)
to test-apply the patches, so patman becomes significantly less useful.
The only real problem that is found with this apply step is trailing spaces.
Provide a -a option to skip this step, for those working with clean patches.
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Doug Anderson <dianders@chromium.org>
Doug Anderson [Fri, 1 Mar 2013 11:11:07 +0000 (11:11 +0000)]
patman: Don't barf if the word 'commit' starts a line
Patman's regular expression for detecting the start of a
commit in a git log was a little simplistic and could be
confused if the git log itself had the word "commit" as
the start of a line (as this commit does). Make patman
a little more robust.
Signed-off-by: Doug Anderson <dianders@chromium.org> Acked-by: Simon Glass <sjg@chromium.org>
Simon Glass [Tue, 26 Mar 2013 13:09:42 +0000 (13:09 +0000)]
patman: Provide option to ignore bad aliases
Often it happens that patches include tags which don't have aliases. It
is annoying that patman fails in this case, and provides no option to
continue other than adding empty tags to the .patman file.
Correct this by adding a '-t' option to ignore tags that don't exist.
Print a warning instead.
Since running the tests is not a common operation, move this to --test
instead, to reserve -t for this new option.
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Doug Anderson <dianders@chromium.org>
Mingkai Hu [Sun, 7 Apr 2013 22:13:32 +0000 (22:13 +0000)]
cmd_sf: include header file common.h before div64.h
The header file div64.h includes <asm/types.h> which defines
the phys_addr_t according to the macro CONFIG_PHYS_64BIT, while
the macro CONFIG_PHYS_64BIT is included in common.h which comes
after div64.h, so in order to get consistent type definition for
phys_addr_t, common.h should be included before div64.h, Or else,
the parameters of phys_addr_t type will be passed wrongly when
CONFIG_PHYS_64BIT is defined.
Signed-off-by: Mingkai Hu <Mingkai.Hu@freescale.com>
introduced cleanup of ext4write semantics to be consistent with other
filesystem's writing commands (e.g. fatwrite).
This commit provides correct ext4write command generation at DFU eMMC
code.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Tom Rini [Fri, 5 Apr 2013 06:21:45 +0000 (06:21 +0000)]
omap5_uevm.h: Move uEVM-specific choices to omap5_uevm.h
The omap5_uevm platform has eMMC, and it makes sense to say that our
default env storage shall reside there. Other platforms may not, so
move this choice to the EVM config. In addition, we should provide some
way to partition the flash for later usage, so take advantage of the GPT
partition table support code and allow that to be setup with some
reasonable defaults.
Cc: Sricharan R <r.sricharan@ti.com> Signed-off-by: Tom Rini <trini@ti.com>
Tom Rini [Fri, 5 Apr 2013 06:21:44 +0000 (06:21 +0000)]
OMAP3/4/5/AM33xx: Correct logic for checking FAT or RAW MMC
In the case of booting from certain peripherals, such as UART, we must
not see what the device descriptor says for RAW or FAT mode because in
addition to being nonsensical, it leads to a hang. This is why we have
a test currently for the boot mode being within range. The problem
however is that on some platforms we get MMC2_2 as the boot mode and not
the defined value for MMC2, and in others we get the value for MMC2_2.
This is required to fix eMMC booting on omap5_uevm.
Tested on am335x_evm (UART, NAND, SD), omap3_beagle (NAND, SD on
classic, SD only on xM rev C5) and omap5_uevm (SD, eMMC).
Commit "8602114 omap: emif: configure emif only when required"
breaks SDRAM_AUTO_DETECTION.
The issue is dmm_init() depends on emif_sizes[](SDRAM Auto detection)
done in do_sdram_init(). The above commit moves dmm_init() above
do_sdram_init() because of which dmm_init() uses uninitialized
emif_sizes[].
So instead of using global emif_sizes[], get sdram details locally
and calculate emif sizes.
Reported-by: Michael Cashwell <mboards@prograde.net> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
SRICHARAN R [Thu, 4 Apr 2013 23:39:47 +0000 (23:39 +0000)]
ARM: OMAP4/5: Make bootz as the default boot command
So with OMAP added to multi platform kernel,
the uImage no more contains a valid load address.
With the uboot already supporting zImage,
change the default boot command to bootz
instead.
SRICHARAN R [Thu, 4 Apr 2013 23:39:27 +0000 (23:39 +0000)]
ARM: OMAP4/5: Change the default boot command to work with device tree
Now with kernel moving to all device tree, the default
boot command is changed to pass the device tree blob.
Also, adding the findfdt command to get the dt-blob
based on the board.
Thanks to Tom Rini <trini@ti.com> for suggesting this.
For production systems it is better to use script images since
they are protected by checksums and carry valuable information
like name and timestamp. Also, you can't validate the content
passed to env import.
But for development, it is easier to use the env import command and
plain text files instead of script-images.
Since both OMAP5evm/uevm boards are used primarily for development,
we allow U-Boot to load env var from a text file in case that an
boot.scr script-image is not present.
The variable uenvcmd (if existent) will be executed (using run) after
uEnv.txt was loaded. If uenvcmd doesn't exist the default boot sequence
will be started.
SRICHARAN R [Mon, 1 Apr 2013 05:52:39 +0000 (05:52 +0000)]
ARM: OMAP5: Set fdt_high to enable booting with Device tree
While booting with dt blob, if fdt_high is not set to
0xffffffff, the dt blob gets relocated to a high ram address,
which the kernel is not able to use without HIGHMEM.
Hunter, Jon [Wed, 3 Apr 2013 09:35:34 +0000 (09:35 +0000)]
omap2420-h4: Fix booting from NOR flash
The omap2420-h4 board is using a RAM based address as the linker
location for code. This is causing several problems when attempting
to run the latest u-boot code base on this board from flash. Update
the default linker location for code to be in NOR flash. Please note
that OMAP maps the NOR flash to address 0x08000000 by default and so
use this as the default address for the NOR flash.
Also remove legacy code that attempts to calculate where in flash the
sdata structure, that holds the memory interface configuration data,
is located. By changing the default linker location for code to flash
this is no longer necessary.
Hunter, Jon [Wed, 3 Apr 2013 09:35:33 +0000 (09:35 +0000)]
omap2420-h4: Fix DRAM initialisation
The size of the DRAM for the omap2420-h4 board is getting setup in the
dram_init() function. However, for the current u-boot release this is
too late and needs to be done in dram_init_banksize(). Therefore, add
a dram_init_banksize() function for the omap2420-h4 board and setup the
DRAM size there.
tricorder: enable hw assisted BCH8 in SPL and u-boot
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com> Cc: Tom Rini <trini@ti.com> Cc: Thomas Weber <weber@corscience.de> Cc: Ilya Yanok <ilya.yanok@cogentembedded.com> Cc: Scott Wood <scottwood@freescale.com>
---8<---
The OMAP3 GPMC hardware BCH engine computes remainder polynomials, it does not
provide automatic error location and correction: this step is implemented using
the BCH library.
--->8---
And we do so in u-boot.
This implementation uses the same layout for BCH8 but it is fix. The current
provided layout does only work with 64 Byte OOB.
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com> Cc: Tom Rini <trini@ti.com> Cc: Ilya Yanok <ilya.yanok@cogentembedded.com> Cc: Scott Wood <scottwood@freescale.com> Cc: Mansoor Ahamed <mansoor.ahamed@ti.com> Cc: Thomas Weber <thomas.weber.linux@googlemail.com>
With uppcoming BCH support on OMAP devices we need to decide between differnt
algorithms when switching the ECC engine. Currently we support 1-bit hammign
and 8-bit BCH on HW backend.
In order to switch between differnet ECC algorithms we need to change the
interface of omap_nand_switch_ecc() also.
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com> Cc: Tom Rini <trini@ti.com> Cc: Thomas Weber <thomas.weber.linux@googlemail.com>
omap3/omap_gpmc.h: add ooblayout for BCH8 as in kernel
This patch adds BCH8 ooblayout for NAND as provided by 0e618ef0a6a33cf7ef96c2c824402088dd8ef48c in linux kernel. This Layout is
currently only provided for 64 byte OOB.
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com> Cc: Tom Rini <trini@ti.com> Cc: Ilya Yanok <ilya.yanok@cogentembedded.com> Cc: Scott Wood <scottwood@freescale.com> Reviewed-by: Tom Rini <trini@ti.com>
arch/arm/include/asm/arch-am33xx/omap_gpmc.h and
arch/arm/include/asm/arch-omap3/omap_gpmc.h are almost the same, consolidate
the common parts into a new header.
Introduce a new asm/omap_gpmc.h which defines the command part and pulls in
the architecture specific one.
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com> Cc: Tom Rini <trini@ti.com> Reviewed-by: Tom Rini <trini@ti.com>
This patch adds the BCH result registers to register mapping for OMAP3 gpmc.
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com> Cc: Tom Rini <trini@ti.com> Cc: Ilya Yanok <ilya.yanok@cogentembedded.com> Cc: Scott Wood <scottwood@freescale.com> Reviewed-by: Tom Rini <trini@ti.com>
Manfred Huber [Fri, 29 Mar 2013 02:52:36 +0000 (02:52 +0000)]
omap3_beagle: Flush UART3 xmit on enable if TEMT is broken
Flush UART3 xmit on enable if TEMT is broken
On some OMAP3 devices when UART3 is configured for boot mode before SPL starts
only THRE bit is set. We have to empty the transmitter before initialization
starts. This patch avoids the use of CONFIG_SYS_NS16550_BROKEN_TEMT.
Signed-off-by: Manfred Huber <man.huber@arcor.de> Tested-by: Javier Martinez Canillas <javier@dowhile0.org> Tested-by: Andreas Bießmann <andreas.devel@googlemail.com>
Bin Liu [Thu, 21 Mar 2013 05:27:48 +0000 (05:27 +0000)]
musb: am335x: disable bulk split-combine feature
On TI AM335x devices, MUSB has bulk split/combine feature enabled
in the ConfigData register, but the current MUSB driver does not
support it yet. Therefore, disable the feature for now, until the
driver adds the support.
One usecase which is broken because of this feature is that Ether
gadget stops working in Fullspeed mode (by un-defining
CONFIG_USB_GADGET_DUALSPEED)
After desabled this feature, MUSB driver send packets in proper size
(no more than 64 bytes) in Fullspeed mode.
This has been validated with Ether gadget in Fullspeed mode on AM335x
EVM.
Simon Glass [Wed, 3 Apr 2013 11:07:16 +0000 (11:07 +0000)]
buildman - U-Boot multi-threaded builder and summary tool
This tool handles building U-Boot to check that you have not broken it
with your patch series. It can build each individual commit and report
which boards fail on which commits, and which errors come up. It also
shows differences in image sizes due to particular commits.
Buildman aims to make full use of multi-processor machines.
Documentation and caveats are in tools/buildman/README.
Simon Glass [Tue, 26 Mar 2013 13:09:40 +0000 (13:09 +0000)]
patman: Don't allow spaces in tags
At present something like:
Revert "arm: Add cache operations"
will try to use
Revert "arm
as a tag. Clearly this is wrong, so fix it.
If the revert is intended to be tagged, then the tag can come before
the revert, perhaps. Alternatively the 'Cc' tag can be used in the commit
messages.
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Doug Anderson <dianders@chromium.org>
Simon Glass [Tue, 26 Mar 2013 13:09:39 +0000 (13:09 +0000)]
patman: Fix up checkpatch parsing to deal with 'CHECK' lines
checkpatch has a new type of warning, a 'CHECK'. At present patman fails
with these, which makes it less than useful.
Add support for checks, making it backwards compatible with the old
checkpatch.
At the same time, clean up formatting of the CheckPatches() output,
fix erroneous "internal error" if multiple patches have warnings and
be more robust to new types of problems.
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Doug Anderson <dianders@chromium.org>
Simon Glass [Wed, 20 Mar 2013 16:43:00 +0000 (16:43 +0000)]
patman: Add Cover-letter-cc tag to Cc cover letter to people
The cover letter is sent to everyone who is on the Cc list for any of
the patches in the series. Sometimes it is useful to send just the cover
letter to additional people, so that they are aware of the series, but
don't need to wade through all the individual patches.
Add a new Cover-letter-cc tag for this purpose.
Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Doug Anderson <dianders@chromium.org>
Doug Anderson [Fri, 15 Mar 2013 13:24:05 +0000 (13:24 +0000)]
patman: Make "Reviewed-by" an important tag
Although "Reviewed-by:" is a tag that gerrit adds, it's also a tag
used by upstream. Stripping it is undesirable. In fact, we should
treat it as important.
Signed-off-by: Doug Anderson <dianders@chromium.org> Reviewed-by: Otavio Salvador <otavio@ossystems.com.br> Acked-by: Simon Glass <sjg@chromium.org>
Simon Glass [Sat, 15 Dec 2012 10:42:06 +0000 (10:42 +0000)]
patman: Allow reading metadata from a list of commits
We normally read from the current branch, but buildman will need to look
at commits from another branch. Allow the metadata to be read from any
list of commits, to provide this flexibility.
Simon Glass [Sat, 15 Dec 2012 10:42:05 +0000 (10:42 +0000)]
patman: Allow commands to raise on error, or not
Make raise_on_error a parameter so that we can control which commands
raise and which do not. If we get an error reading the alias file, just
continue.
Simon Glass [Sat, 15 Dec 2012 10:42:04 +0000 (10:42 +0000)]
patman: Make command methods return a CommandResult
Rather than returning a list of things, return an object. That makes it
easier to access the returned items, and easier to extend the return
value later.
Simon Glass [Sat, 15 Dec 2012 10:42:03 +0000 (10:42 +0000)]
patman: Add cros_subprocess library to manage subprocesses
This adds a new library on top of subprocess which permits access to
the subprocess output as it is being generated. We can therefore
give the illusion that a process is running independently, but still
monitor its output so that we know what is going on.
It is possible to display output on a terminal as it is generated
(a little like tee). The supplied output function is called with all
stdout/stderr data as it arrives.
Simon Glass [Sat, 15 Dec 2012 10:42:01 +0000 (10:42 +0000)]
patman: Use ANSI colours only when outputting to a terminal
It is easy to detect whether or not the process is connected to a terminal,
or piped to a file. Disable ANSI colours automatically when output is
not to a terminal.
Dirk Behme [Wed, 20 Mar 2013 22:03:44 +0000 (22:03 +0000)]
spi: mxc_spi: Fix ECSPI reset handling
Reviewing the ECSPI reset handling shows two issues:
1. For the enable/reset bit (MXC_CSPICTRL_EN) in the control reg
(ECSPIx_CONGREG) the i.MX6 technical reference manual states:
-- cut --
ECSPIx_CONREG[0]: EN: Writing zero to this bit disables the block
and resets the internal logic with the exception of the ECSPI_CONREG.
-- cut --
Note the exception mentioned: The CONREG itself isn't reset.
Fix this by manually writing the reset value 0 to the whole register.
This sets the EN bit to zero, too (i.e. includes the old
~MXC_CSPICTRL_EN).
2. We want to reset the whole SPI block here. So it makes no sense
to first read the old value of the CONREG and write it back, later.
This will give us the old (historic/random) value of the CONREG back.
And doesn't reset the CONREG.
To get a clean CONREG after the reset of the block, too, don't use
the old (historic/random) value of the CONREG while doing the reset.
And read the clean CONREG after the reset.
This was found while working on a SPI boot device where the i.MX6 boot
ROM has already initialized the SPI block. The initialization by the
boot ROM might be different to what the U-Boot driver wants to configure.
I.e. we need a clean reset of SPI block, including the CONREG.
Stefan Roese [Wed, 3 Apr 2013 00:47:46 +0000 (02:47 +0200)]
cfi_flash: Use uintptr_t for casts from u32 to void *
This fixes this build warning:
Configuring for qemu_mips64 - Board: qemu-mips64, Options: SYS_BIG_ENDIAN
text data bss dec hex filename
215344 13082 218720 447146 6d2aa qemu_mips64/u-boot
cfi_flash.c: In function 'flash_map':
cfi_flash.c:217:9: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
Signed-off-by: Stefan Roese <sr@denx.de> Cc: Tom Rini <trini@ti.com>
i.MX6: mx6qsabrelite: README: don't pass chip-select to sf probe command
board/freescale/mx6qsabrelite/README explain a procedure to
update the SPI-NOR on the SabreLite board without Freescale
manufacturing tool but following this procedure leads to both
"sf erase" and "sf write" failing on a mx6qsabrelite board:
MX6QSABRELITE U-Boot > sf probe 1
MX6QSABRELITE U-Boot > sf erase 0 0x40000
SPI flash erase failed
MX6QSABRELITE U-Boot > sf write 0x10800000 0 0x40000
SPI flash write failed
This is because the chip-select 1 is wrong and the correct
value is 0x7300.
Since commit c1173bd0 ("sf command: allow default bus and chip selects")
the chip-select and bus arguments for the sf probe command are optional
so let's just remove it and use "sf probe" instead.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
projects / karo-tx-uboot.git / log