--- /dev/null
+/*
+ *
+ * Copyright (C) 2010 Eric Bénard <eric@eukrea.com>
+ *
+ * based on board-mx51_babbage.c which is
+ * Copyright 2009 Freescale Semiconductor, Inc. All Rights Reserved.
+ * Copyright (C) 2009-2010 Amit Kucheria <amit.kucheria@canonical.com>
+ *
+ * The code contained herein is licensed under the GNU General Public
+ * License. You may obtain a copy of the GNU General Public License
+ * Version 2 or later at the following locations:
+ *
+ * http://www.opensource.org/licenses/gpl-license.html
+ * http://www.gnu.org/copyleft/gpl.html
+ */
+
+#include <linux/init.h>
+#include <linux/platform_device.h>
+#include <linux/i2c.h>
+#include <linux/i2c/tsc2007.h>
+#include <linux/gpio.h>
+#include <linux/delay.h>
+#include <linux/io.h>
+#include <linux/interrupt.h>
+#include <linux/irq.h>
+#include <linux/fsl_devices.h>
+#include <linux/i2c-gpio.h>
+#include <linux/spi/spi.h>
+#include <linux/can/platform/mcp251x.h>
+
+#include <mach/eukrea-baseboards.h>
+#include <mach/common.h>
+#include <mach/hardware.h>
+#include <mach/iomux-mx51.h>
+#include <mach/mxc_ehci.h>
+
+#include <asm/irq.h>
+#include <asm/setup.h>
+#include <asm/mach-types.h>
+#include <asm/mach/arch.h>
+#include <asm/mach/time.h>
+
+#include "devices-imx51.h"
+#include "devices.h"
+
+#define USBH1_RST (1*32 + 28)
+#define ETH_RST (1*32 + 31)
+#define TSC2007_IRQGPIO (2*32 + 12)
+#define CAN_IRQGPIO (0*32 + 1)
+#define CAN_RST (3*32 + 15)
+#define CAN_NCS (3*32 + 24)
+#define CAN_RXOBF (0*32 + 4)
+#define CAN_RX1BF (0*32 + 6)
+#define CAN_TXORTS (0*32 + 7)
+#define CAN_TX1RTS (0*32 + 8)
+#define CAN_TX2RTS (0*32 + 9)
+#define I2C_SCL (3*32 + 16)
+#define I2C_SDA (3*32 + 17)
+
+/* USB_CTRL_1 */
+#define MX51_USB_CTRL_1_OFFSET 0x10
+#define MX51_USB_CTRL_UH1_EXT_CLK_EN (1 << 25)
+
+#define MX51_USB_PLLDIV_12_MHZ 0x00
+#define MX51_USB_PLL_DIV_19_2_MHZ 0x01
+#define MX51_USB_PLL_DIV_24_MHZ 0x02
+
+#define CPUIMX51SD_GPIO_3_12 IOMUX_PAD(0x57C, 0x194, 3, 0x0, 0, \
+ MX51_PAD_CTRL_1 | PAD_CTL_PUS_22K_UP)
+
+static struct pad_desc eukrea_cpuimx51sd_pads[] = {
+ /* UART1 */
+ MX51_PAD_UART1_RXD__UART1_RXD,
+ MX51_PAD_UART1_TXD__UART1_TXD,
+ MX51_PAD_UART1_RTS__UART1_RTS,
+ MX51_PAD_UART1_CTS__UART1_CTS,
+
+ /* USB HOST1 */
+ MX51_PAD_USBH1_CLK__USBH1_CLK,
+ MX51_PAD_USBH1_DIR__USBH1_DIR,
+ MX51_PAD_USBH1_NXT__USBH1_NXT,
+ MX51_PAD_USBH1_DATA0__USBH1_DATA0,
+ MX51_PAD_USBH1_DATA1__USBH1_DATA1,
+ MX51_PAD_USBH1_DATA2__USBH1_DATA2,
+ MX51_PAD_USBH1_DATA3__USBH1_DATA3,
+ MX51_PAD_USBH1_DATA4__USBH1_DATA4,
+ MX51_PAD_USBH1_DATA5__USBH1_DATA5,
+ MX51_PAD_USBH1_DATA6__USBH1_DATA6,
+ MX51_PAD_USBH1_DATA7__USBH1_DATA7,
+ MX51_PAD_USBH1_STP__USBH1_STP,
+ MX51_PAD_EIM_CS3__GPIO_2_28, /* PHY nRESET */
+
+ /* FEC */
+ MX51_PAD_EIM_DTACK__GPIO_2_31, /* PHY nRESET */
+
+ /* HSI2C */
+ MX51_PAD_I2C1_CLK__GPIO_4_16,
+ MX51_PAD_I2C1_DAT__GPIO_4_17,
+
+ /* CAN */
+ MX51_PAD_CSPI1_MOSI__ECSPI1_MOSI,
+ MX51_PAD_CSPI1_MISO__ECSPI1_MISO,
+ MX51_PAD_CSPI1_SCLK__ECSPI1_SCLK,
+ MX51_PAD_CSPI1_SS0__GPIO_4_24, /* nCS */
+ MX51_PAD_CSI2_PIXCLK__GPIO_4_15, /* nReset */
+ MX51_PAD_GPIO_1_1__GPIO_1_1, /* IRQ */
+ MX51_PAD_GPIO_1_4__GPIO_1_4, /* Control signals */
+ MX51_PAD_GPIO_1_6__GPIO_1_6,
+ MX51_PAD_GPIO_1_7__GPIO_1_7,
+ MX51_PAD_GPIO_1_8__GPIO_1_8,
+ MX51_PAD_GPIO_1_9__GPIO_1_9,
+
+ /* Touchscreen */
+ CPUIMX51SD_GPIO_3_12, /* IRQ */
+};
+
+static const struct imxuart_platform_data uart_pdata __initconst = {
+ .flags = IMXUART_HAVE_RTSCTS,
+};
+
+static int ts_get_pendown_state(void)
+{
+ return gpio_get_value(TSC2007_IRQGPIO) ? 0 : 1;
+}
+
+static struct tsc2007_platform_data tsc2007_info = {
+ .model = 2007,
+ .x_plate_ohms = 180,
+ .get_pendown_state = ts_get_pendown_state,
+};
+
+static struct i2c_board_info eukrea_cpuimx51sd_i2c_devices[] = {
+ {
+ I2C_BOARD_INFO("pcf8563", 0x51),
+ }, {
+ I2C_BOARD_INFO("tsc2007", 0x49),
+ .type = "tsc2007",
+ .platform_data = &tsc2007_info,
+ .irq = gpio_to_irq(TSC2007_IRQGPIO),
+ },
+};
+
+static const struct mxc_nand_platform_data
+ eukrea_cpuimx51sd_nand_board_info __initconst = {
+ .width = 1,
+ .hw_ecc = 1,
+ .flash_bbt = 1,
+};
+
+/* This function is board specific as the bit mask for the plldiv will also
+be different for other Freescale SoCs, thus a common bitmask is not
+possible and cannot get place in /plat-mxc/ehci.c.*/
+static int initialize_otg_port(struct platform_device *pdev)
+{
+ u32 v;
+ void __iomem *usb_base;
+ void __iomem *usbother_base;
+
+ usb_base = ioremap(MX51_OTG_BASE_ADDR, SZ_4K);
+ usbother_base = usb_base + MX5_USBOTHER_REGS_OFFSET;
+
+ /* Set the PHY clock to 19.2MHz */
+ v = __raw_readl(usbother_base + MXC_USB_PHY_CTR_FUNC2_OFFSET);
+ v &= ~MX5_USB_UTMI_PHYCTRL1_PLLDIV_MASK;
+ v |= MX51_USB_PLL_DIV_19_2_MHZ;
+ __raw_writel(v, usbother_base + MXC_USB_PHY_CTR_FUNC2_OFFSET);
+ iounmap(usb_base);
+ return 0;
+}
+
+static int initialize_usbh1_port(struct platform_device *pdev)
+{
+ u32 v;
+ void __iomem *usb_base;
+ void __iomem *usbother_base;
+
+ usb_base = ioremap(MX51_OTG_BASE_ADDR, SZ_4K);
+ usbother_base = usb_base + MX5_USBOTHER_REGS_OFFSET;
+
+ /* The clock for the USBH1 ULPI port will come from the PHY. */
+ v = __raw_readl(usbother_base + MX51_USB_CTRL_1_OFFSET);
+ __raw_writel(v | MX51_USB_CTRL_UH1_EXT_CLK_EN,
+ usbother_base + MX51_USB_CTRL_1_OFFSET);
+ iounmap(usb_base);
+ return 0;
+}
+
+static struct mxc_usbh_platform_data dr_utmi_config = {
+ .init = initialize_otg_port,
+ .portsc = MXC_EHCI_UTMI_16BIT,
+ .flags = MXC_EHCI_INTERNAL_PHY,
+};
+
+static struct fsl_usb2_platform_data usb_pdata = {
+ .operating_mode = FSL_USB2_DR_DEVICE,
+ .phy_mode = FSL_USB2_PHY_UTMI_WIDE,
+};
+
+static struct mxc_usbh_platform_data usbh1_config = {
+ .init = initialize_usbh1_port,
+ .portsc = MXC_EHCI_MODE_ULPI,
+ .flags = (MXC_EHCI_POWER_PINS_ENABLED | MXC_EHCI_ITC_NO_THRESHOLD),
+};
+
+static int otg_mode_host;
+
+static int __init eukrea_cpuimx51sd_otg_mode(char *options)
+{
+ if (!strcmp(options, "host"))
+ otg_mode_host = 1;
+ else if (!strcmp(options, "device"))
+ otg_mode_host = 0;
+ else
+ pr_info("otg_mode neither \"host\" nor \"device\". "
+ "Defaulting to device\n");
+ return 0;
+}
+__setup("otg_mode=", eukrea_cpuimx51sd_otg_mode);
+
+static struct i2c_gpio_platform_data pdata = {
+ .sda_pin = I2C_SDA,
+ .sda_is_open_drain = 0,
+ .scl_pin = I2C_SCL,
+ .scl_is_open_drain = 0,
+ .udelay = 2,
+};
+
+static struct platform_device hsi2c_gpio_device = {
+ .name = "i2c-gpio",
+ .id = 0,
+ .dev.platform_data = &pdata,
+};
+
+static struct mcp251x_platform_data mcp251x_info = {
+ .oscillator_frequency = 24E6,
+};
+
+static struct spi_board_info cpuimx51sd_spi_device[] = {
+ {
+ .modalias = "mcp2515",
+ .max_speed_hz = 6500000,
+ .bus_num = 0,
+ .mode = SPI_MODE_0,
+ .chip_select = 0,
+ .platform_data = &mcp251x_info,
+ .irq = gpio_to_irq(0 * 32 + 1)
+ },
+};
+
+static int cpuimx51sd_spi1_cs[] = {
+ CAN_NCS,
+};
+
+static const struct spi_imx_master cpuimx51sd_ecspi1_pdata __initconst = {
+ .chipselect = cpuimx51sd_spi1_cs,
+ .num_chipselect = ARRAY_SIZE(cpuimx51sd_spi1_cs),
+};
+
+static struct platform_device *platform_devices[] __initdata = {
+ &hsi2c_gpio_device,
+};
+
+static void __init eukrea_cpuimx51sd_init(void)
+{
+ mxc_iomux_v3_setup_multiple_pads(eukrea_cpuimx51sd_pads,
+ ARRAY_SIZE(eukrea_cpuimx51sd_pads));
+
+ imx51_add_imx_uart(0, &uart_pdata);
+ imx51_add_mxc_nand(&eukrea_cpuimx51sd_nand_board_info);
+
+ gpio_request(ETH_RST, "eth_rst");
+ gpio_set_value(ETH_RST, 1);
+ imx51_add_fec(NULL);
+
+ gpio_request(CAN_IRQGPIO, "can_irq");
+ gpio_direction_input(CAN_IRQGPIO);
+ gpio_free(CAN_IRQGPIO);
+ gpio_request(CAN_NCS, "can_ncs");
+ gpio_direction_output(CAN_NCS, 1);
+ gpio_free(CAN_NCS);
+ gpio_request(CAN_RST, "can_rst");
+ gpio_direction_output(CAN_RST, 0);
+ msleep(20);
+ gpio_set_value(CAN_RST, 1);
+ imx51_add_ecspi(0, &cpuimx51sd_ecspi1_pdata);
+ spi_register_board_info(cpuimx51sd_spi_device,
+ ARRAY_SIZE(cpuimx51sd_spi_device));
+
+ gpio_request(TSC2007_IRQGPIO, "tsc2007_irq");
+ gpio_direction_input(TSC2007_IRQGPIO);
+ gpio_free(TSC2007_IRQGPIO);
+
+ i2c_register_board_info(0, eukrea_cpuimx51sd_i2c_devices,
+ ARRAY_SIZE(eukrea_cpuimx51sd_i2c_devices));
+ platform_add_devices(platform_devices, ARRAY_SIZE(platform_devices));
+
+ if (otg_mode_host)
+ mxc_register_device(&mxc_usbdr_host_device, &dr_utmi_config);
+ else {
+ initialize_otg_port(NULL);
+ mxc_register_device(&mxc_usbdr_udc_device, &usb_pdata);
+ }
+
+ gpio_request(USBH1_RST, "usb_rst");
+ gpio_direction_output(USBH1_RST, 0);
+ msleep(20);
+ gpio_set_value(USBH1_RST, 1);
+ mxc_register_device(&mxc_usbh1_device, &usbh1_config);
+
+#ifdef CONFIG_MACH_EUKREA_MBIMXSD51_BASEBOARD
+ eukrea_mbimxsd51_baseboard_init();
+#endif
+}
+
+static void __init eukrea_cpuimx51sd_timer_init(void)
+{
+ mx51_clocks_init(32768, 24000000, 22579200, 0);
+}
+
+static struct sys_timer mxc_timer = {
+ .init = eukrea_cpuimx51sd_timer_init,
+};
+
+MACHINE_START(EUKREA_CPUIMX51SD, "Eukrea CPUIMX51SD")
+ /* Maintainer: Eric Bénard <eric@eukrea.com> */
+ .phys_io = MX51_AIPS1_BASE_ADDR,
+ .io_pg_offst = ((MX51_AIPS1_BASE_ADDR_VIRT) >> 18) & 0xfffc,
+ .boot_params = PHYS_OFFSET + 0x100,
+ .map_io = mx51_map_io,
+ .init_irq = mx51_init_irq,
+ .init_machine = eukrea_cpuimx51sd_init,
+ .timer = &mxc_timer,
+MACHINE_END
--- /dev/null
+/*
+ * Copyright (C) 2010 Eric Benard - eric@eukrea.com
+ *
+ * Based on pcm970-baseboard.c which is :
+ * Copyright (C) 2008 Juergen Beisert (kernel@pengutronix.de)
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * as published by the Free Software Foundation; either version 2
+ * of the License, or (at your option) any later version.
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
+ * MA 02110-1301, USA.
+ */
+
+#include <linux/types.h>
+#include <linux/init.h>
+
+#include <linux/gpio.h>
+#include <linux/interrupt.h>
+#include <linux/irq.h>
+#include <linux/leds.h>
+#include <linux/platform_device.h>
+#include <linux/gpio_keys.h>
+#include <linux/input.h>
+#include <linux/i2c.h>
+
+#include <asm/mach-types.h>
+#include <asm/mach/arch.h>
+#include <asm/mach/time.h>
+#include <asm/mach/map.h>
+
+#include <mach/hardware.h>
+#include <mach/common.h>
+#include <mach/imx-uart.h>
+#include <mach/iomux-mx51.h>
+#include <mach/audmux.h>
+
+#include "devices-imx51.h"
+#include "devices.h"
+
+#define MBIMXSD_GPIO_3_31 IOMUX_PAD(0x554, 0x16C, 3, 0x0, 0, \
+ MX51_PAD_CTRL_1 | PAD_CTL_PUS_22K_UP)
+
+static struct pad_desc eukrea_mbimxsd_pads[] = {
+ /* LED */
+ MX51_PAD_NANDF_D10__GPIO_3_30,
+ /* SWITCH */
+ MBIMXSD_GPIO_3_31,
+ /* UART2 */
+ MX51_PAD_UART2_RXD__UART2_RXD,
+ MX51_PAD_UART2_TXD__UART2_TXD,
+ /* UART 3 */
+ MX51_PAD_UART3_RXD__UART3_RXD,
+ MX51_PAD_UART3_TXD__UART3_TXD,
+ MX51_PAD_KEY_COL4__UART3_RTS,
+ MX51_PAD_KEY_COL5__UART3_CTS,
+ /* SD */
+ MX51_PAD_SD1_CMD__SD1_CMD,
+ MX51_PAD_SD1_CLK__SD1_CLK,
+ MX51_PAD_SD1_DATA0__SD1_DATA0,
+ MX51_PAD_SD1_DATA1__SD1_DATA1,
+ MX51_PAD_SD1_DATA2__SD1_DATA2,
+ MX51_PAD_SD1_DATA3__SD1_DATA3,
+};
+
+#define GPIO_LED1 (2 * 32 + 30)
+#define GPIO_SWITCH1 (2 * 32 + 31)
+
+static struct gpio_led eukrea_mbimxsd_leds[] = {
+ {
+ .name = "led1",
+ .default_trigger = "heartbeat",
+ .active_low = 1,
+ .gpio = GPIO_LED1,
+ },
+};
+
+static struct gpio_led_platform_data eukrea_mbimxsd_led_info = {
+ .leds = eukrea_mbimxsd_leds,
+ .num_leds = ARRAY_SIZE(eukrea_mbimxsd_leds),
+};
+
+static struct platform_device eukrea_mbimxsd_leds_gpio = {
+ .name = "leds-gpio",
+ .id = -1,
+ .dev = {
+ .platform_data = &eukrea_mbimxsd_led_info,
+ },
+};
+
+static struct gpio_keys_button eukrea_mbimxsd_gpio_buttons[] = {
+ {
+ .gpio = GPIO_SWITCH1,
+ .code = BTN_0,
+ .desc = "BP1",
+ .active_low = 1,
+ .wakeup = 1,
+ },
+};
+
+static struct gpio_keys_platform_data eukrea_mbimxsd_button_data = {
+ .buttons = eukrea_mbimxsd_gpio_buttons,
+ .nbuttons = ARRAY_SIZE(eukrea_mbimxsd_gpio_buttons),
+};
+
+static struct platform_device eukrea_mbimxsd_button_device = {
+ .name = "gpio-keys",
+ .id = -1,
+ .num_resources = 0,
+ .dev = {
+ .platform_data = &eukrea_mbimxsd_button_data,
+ }
+};
+
+static struct platform_device *platform_devices[] __initdata = {
+ &eukrea_mbimxsd_leds_gpio,
+ &eukrea_mbimxsd_button_device,
+};
+
+static const struct imxuart_platform_data uart_pdata __initconst = {
+ .flags = IMXUART_HAVE_RTSCTS,
+};
+
+static struct i2c_board_info eukrea_mbimxsd_i2c_devices[] = {
+ {
+ I2C_BOARD_INFO("tlv320aic23", 0x1a),
+ },
+};
+
+/*
+ * system init for baseboard usage. Will be called by cpuimx51sd init.
+ *
+ * Add platform devices present on this baseboard and init
+ * them from CPU side as far as required to use them later on
+ */
+void __init eukrea_mbimxsd51_baseboard_init(void)
+{
+ if (mxc_iomux_v3_setup_multiple_pads(eukrea_mbimxsd_pads,
+ ARRAY_SIZE(eukrea_mbimxsd_pads)))
+ printk(KERN_ERR "error setting mbimxsd pads !\n");
+
+ imx51_add_imx_uart(1, NULL);
+ imx51_add_imx_uart(2, &uart_pdata);
+
+ imx51_add_esdhc(0, NULL);
+
+ gpio_request(GPIO_LED1, "LED1");
+ gpio_direction_output(GPIO_LED1, 1);
+ gpio_free(GPIO_LED1);
+
+ gpio_request(GPIO_SWITCH1, "SWITCH1");
+ gpio_direction_input(GPIO_SWITCH1);
+ gpio_free(GPIO_SWITCH1);
+
+ i2c_register_board_info(0, eukrea_mbimxsd_i2c_devices,
+ ARRAY_SIZE(eukrea_mbimxsd_i2c_devices));
+
+ platform_add_devices(platform_devices, ARRAY_SIZE(platform_devices));
+}
projects / mv-sheeva.git / commitdiff