2 # (C) Copyright 2000 - 2009
3 # Wolfgang Denk, DENX Software Engineering, wd@denx.de.
5 # See file CREDITS for list of people who contributed to this
8 # This program is free software; you can redistribute it and/or
9 # modify it under the terms of the GNU General Public License as
10 # published by the Free Software Foundation; either version 2 of
11 # the License, or (at your option) any later version.
13 # This program is distributed in the hope that it will be useful,
14 # but WITHOUT ANY WARRANTY; without even the implied warranty of
15 # MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
16 # GNU General Public License for more details.
18 # You should have received a copy of the GNU General Public License
19 # along with this program; if not, write to the Free Software
20 # Foundation, Inc., 59 Temple Place, Suite 330, Boston,
27 This directory contains the source code for U-Boot, a boot loader for
28 Embedded boards based on PowerPC, ARM, MIPS and several other
29 processors, which can be installed in a boot ROM and used to
30 initialize and test the hardware or to download and run application
33 The development of U-Boot is closely related to Linux: some parts of
34 the source code originate in the Linux source tree, we have some
35 header files in common, and special provision has been made to
36 support booting of Linux images.
38 Some attention has been paid to make this software easily
39 configurable and extendable. For instance, all monitor commands are
40 implemented with the same call interface, so that it's very easy to
41 add new commands. Also, instead of permanently adding rarely used
42 code (for instance hardware test utilities) to the monitor, you can
43 load and run it dynamically.
49 In general, all boards for which a configuration option exists in the
50 Makefile have been tested to some extent and can be considered
51 "working". In fact, many of them are used in production systems.
53 In case of problems see the CHANGELOG and CREDITS files to find out
54 who contributed the specific port. The MAINTAINERS file lists board
61 In case you have questions about, problems with or contributions for
62 U-Boot you should send a message to the U-Boot mailing list at
63 <u-boot@lists.denx.de>. There is also an archive of previous traffic
64 on the mailing list - please search the archive before asking FAQ's.
65 Please see http://lists.denx.de/pipermail/u-boot and
66 http://dir.gmane.org/gmane.comp.boot-loaders.u-boot
69 Where to get source code:
70 =========================
72 The U-Boot source code is maintained in the git repository at
73 git://www.denx.de/git/u-boot.git ; you can browse it online at
74 http://www.denx.de/cgi-bin/gitweb.cgi?p=u-boot.git;a=summary
76 The "snapshot" links on this page allow you to download tarballs of
77 any version you might be interested in. Official releases are also
78 available for FTP download from the ftp://ftp.denx.de/pub/u-boot/
81 Pre-built (and tested) images are available from
82 ftp://ftp.denx.de/pub/u-boot/images/
88 - start from 8xxrom sources
89 - create PPCBoot project (http://sourceforge.net/projects/ppcboot)
91 - make it easier to add custom boards
92 - make it possible to add other [PowerPC] CPUs
93 - extend functions, especially:
94 * Provide extended interface to Linux boot loader
97 * PCMCIA / CompactFlash / ATA disk / SCSI ... boot
98 - create ARMBoot project (http://sourceforge.net/projects/armboot)
99 - add other CPU families (starting with ARM)
100 - create U-Boot project (http://sourceforge.net/projects/u-boot)
101 - current project page: see http://www.denx.de/wiki/U-Boot
107 The "official" name of this project is "Das U-Boot". The spelling
108 "U-Boot" shall be used in all written text (documentation, comments
109 in source files etc.). Example:
111 This is the README file for the U-Boot project.
113 File names etc. shall be based on the string "u-boot". Examples:
115 include/asm-ppc/u-boot.h
117 #include <asm/u-boot.h>
119 Variable names, preprocessor constants etc. shall be either based on
120 the string "u_boot" or on "U_BOOT". Example:
122 U_BOOT_VERSION u_boot_logo
123 IH_OS_U_BOOT u_boot_hush_start
129 Starting with the release in October 2008, the names of the releases
130 were changed from numerical release numbers without deeper meaning
131 into a time stamp based numbering. Regular releases are identified by
132 names consisting of the calendar year and month of the release date.
133 Additional fields (if present) indicate release candidates or bug fix
134 releases in "stable" maintenance trees.
137 U-Boot v2009.11 - Release November 2009
138 U-Boot v2009.11.1 - Release 1 in version November 2009 stable tree
139 U-Boot v2010.09-rc1 - Release candiate 1 for September 2010 release
145 /arch Architecture specific files
146 /arm Files generic to ARM architecture
147 /cpu CPU specific files
148 /arm720t Files specific to ARM 720 CPUs
149 /arm920t Files specific to ARM 920 CPUs
150 /at91rm9200 Files specific to Atmel AT91RM9200 CPU
151 /imx Files specific to Freescale MC9328 i.MX CPUs
152 /s3c24x0 Files specific to Samsung S3C24X0 CPUs
153 /arm925t Files specific to ARM 925 CPUs
154 /arm926ejs Files specific to ARM 926 CPUs
155 /arm1136 Files specific to ARM 1136 CPUs
156 /ixp Files specific to Intel XScale IXP CPUs
157 /pxa Files specific to Intel XScale PXA CPUs
158 /s3c44b0 Files specific to Samsung S3C44B0 CPUs
159 /sa1100 Files specific to Intel StrongARM SA1100 CPUs
160 /lib Architecture specific library files
161 /avr32 Files generic to AVR32 architecture
162 /cpu CPU specific files
163 /lib Architecture specific library files
164 /blackfin Files generic to Analog Devices Blackfin architecture
165 /cpu CPU specific files
166 /lib Architecture specific library files
167 /x86 Files generic to x86 architecture
168 /cpu CPU specific files
169 /lib Architecture specific library files
170 /m68k Files generic to m68k architecture
171 /cpu CPU specific files
172 /mcf52x2 Files specific to Freescale ColdFire MCF52x2 CPUs
173 /mcf5227x Files specific to Freescale ColdFire MCF5227x CPUs
174 /mcf532x Files specific to Freescale ColdFire MCF5329 CPUs
175 /mcf5445x Files specific to Freescale ColdFire MCF5445x CPUs
176 /mcf547x_8x Files specific to Freescale ColdFire MCF547x_8x CPUs
177 /lib Architecture specific library files
178 /microblaze Files generic to microblaze architecture
179 /cpu CPU specific files
180 /lib Architecture specific library files
181 /mips Files generic to MIPS architecture
182 /cpu CPU specific files
183 /lib Architecture specific library files
184 /nios2 Files generic to Altera NIOS2 architecture
185 /cpu CPU specific files
186 /lib Architecture specific library files
187 /powerpc Files generic to PowerPC architecture
188 /cpu CPU specific files
189 /74xx_7xx Files specific to Freescale MPC74xx and 7xx CPUs
190 /mpc5xx Files specific to Freescale MPC5xx CPUs
191 /mpc5xxx Files specific to Freescale MPC5xxx CPUs
192 /mpc8xx Files specific to Freescale MPC8xx CPUs
193 /mpc8220 Files specific to Freescale MPC8220 CPUs
194 /mpc824x Files specific to Freescale MPC824x CPUs
195 /mpc8260 Files specific to Freescale MPC8260 CPUs
196 /mpc85xx Files specific to Freescale MPC85xx CPUs
197 /ppc4xx Files specific to AMCC PowerPC 4xx CPUs
198 /lib Architecture specific library files
199 /sh Files generic to SH architecture
200 /cpu CPU specific files
201 /sh2 Files specific to sh2 CPUs
202 /sh3 Files specific to sh3 CPUs
203 /sh4 Files specific to sh4 CPUs
204 /lib Architecture specific library files
205 /sparc Files generic to SPARC architecture
206 /cpu CPU specific files
207 /leon2 Files specific to Gaisler LEON2 SPARC CPU
208 /leon3 Files specific to Gaisler LEON3 SPARC CPU
209 /lib Architecture specific library files
210 /api Machine/arch independent API for external apps
211 /board Board dependent files
212 /common Misc architecture independent functions
213 /disk Code for disk drive partition handling
214 /doc Documentation (don't expect too much)
215 /drivers Commonly used device drivers
216 /examples Example code for standalone applications, etc.
217 /fs Filesystem code (cramfs, ext2, jffs2, etc.)
218 /include Header Files
219 /lib Files generic to all architectures
220 /libfdt Library files to support flattened device trees
221 /lzma Library files to support LZMA decompression
222 /lzo Library files to support LZO decompression
224 /post Power On Self Test
225 /rtc Real Time Clock drivers
226 /tools Tools to build S-Record or U-Boot images, etc.
228 Software Configuration:
229 =======================
231 Configuration is usually done using C preprocessor defines; the
232 rationale behind that is to avoid dead code whenever possible.
234 There are two classes of configuration variables:
236 * Configuration _OPTIONS_:
237 These are selectable by the user and have names beginning with
240 * Configuration _SETTINGS_:
241 These depend on the hardware etc. and should not be meddled with if
242 you don't know what you're doing; they have names beginning with
245 Later we will add a configuration tool - probably similar to or even
246 identical to what's used for the Linux kernel. Right now, we have to
247 do the configuration by hand, which means creating some symbolic
248 links and editing some configuration files. We use the TQM8xxL boards
252 Selection of Processor Architecture and Board Type:
253 ---------------------------------------------------
255 For all supported boards there are ready-to-use default
256 configurations available; just type "make <board_name>_config".
258 Example: For a TQM823L module type:
263 For the Cogent platform, you need to specify the CPU type as well;
264 e.g. "make cogent_mpc8xx_config". And also configure the cogent
265 directory according to the instructions in cogent/README.
268 Configuration Options:
269 ----------------------
271 Configuration depends on the combination of board and CPU type; all
272 such information is kept in a configuration file
273 "include/configs/<board_name>.h".
275 Example: For a TQM823L module, all configuration settings are in
276 "include/configs/TQM823L.h".
279 Many of the options are named exactly as the corresponding Linux
280 kernel configuration options. The intention is to make it easier to
281 build a config tool - later.
284 The following options need to be configured:
286 - CPU Type: Define exactly one, e.g. CONFIG_MPC85XX.
288 - Board Type: Define exactly one, e.g. CONFIG_MPC8540ADS.
290 - CPU Daughterboard Type: (if CONFIG_ATSTK1000 is defined)
291 Define exactly one, e.g. CONFIG_ATSTK1002
293 - CPU Module Type: (if CONFIG_COGENT is defined)
294 Define exactly one of
296 --- FIXME --- not tested yet:
297 CONFIG_CMA286_60, CONFIG_CMA286_21, CONFIG_CMA286_60P,
298 CONFIG_CMA287_23, CONFIG_CMA287_50
300 - Motherboard Type: (if CONFIG_COGENT is defined)
301 Define exactly one of
302 CONFIG_CMA101, CONFIG_CMA102
304 - Motherboard I/O Modules: (if CONFIG_COGENT is defined)
305 Define one or more of
308 - Motherboard Options: (if CONFIG_CMA101 or CONFIG_CMA102 are defined)
309 Define one or more of
310 CONFIG_LCD_HEARTBEAT - update a character position on
311 the LCD display every second with
314 - Board flavour: (if CONFIG_MPC8260ADS is defined)
317 CONFIG_SYS_8260ADS - original MPC8260ADS
318 CONFIG_SYS_8266ADS - MPC8266ADS
319 CONFIG_SYS_PQ2FADS - PQ2FADS-ZU or PQ2FADS-VR
320 CONFIG_SYS_8272ADS - MPC8272ADS
322 - Marvell Family Member
323 CONFIG_SYS_MVFS - define it if you want to enable
324 multiple fs option at one time
325 for marvell soc family
327 - MPC824X Family Member (if CONFIG_MPC824X is defined)
328 Define exactly one of
329 CONFIG_MPC8240, CONFIG_MPC8245
331 - 8xx CPU Options: (if using an MPC8xx CPU)
332 CONFIG_8xx_GCLK_FREQ - deprecated: CPU clock if
333 get_gclk_freq() cannot work
334 e.g. if there is no 32KHz
335 reference PIT/RTC clock
336 CONFIG_8xx_OSCLK - PLL input clock (either EXTCLK
339 - 859/866/885 CPU options: (if using a MPC859 or MPC866 or MPC885 CPU):
340 CONFIG_SYS_8xx_CPUCLK_MIN
341 CONFIG_SYS_8xx_CPUCLK_MAX
342 CONFIG_8xx_CPUCLK_DEFAULT
343 See doc/README.MPC866
345 CONFIG_SYS_MEASURE_CPUCLK
347 Define this to measure the actual CPU clock instead
348 of relying on the correctness of the configured
349 values. Mostly useful for board bringup to make sure
350 the PLL is locked at the intended frequency. Note
351 that this requires a (stable) reference clock (32 kHz
352 RTC clock or CONFIG_SYS_8XX_XIN)
354 CONFIG_SYS_DELAYED_ICACHE
356 Define this option if you want to enable the
357 ICache only when Code runs from RAM.
360 CONFIG_SYS_FSL_TBCLK_DIV
362 Defines the core time base clock divider ratio compared to the
363 system clock. On most PQ3 devices this is 8, on newer QorIQ
364 devices it can be 16 or 32. The ratio varies from SoC to Soc.
366 - Intel Monahans options:
367 CONFIG_SYS_MONAHANS_RUN_MODE_OSC_RATIO
369 Defines the Monahans run mode to oscillator
370 ratio. Valid values are 8, 16, 24, 31. The core
371 frequency is this value multiplied by 13 MHz.
373 CONFIG_SYS_MONAHANS_TURBO_RUN_MODE_RATIO
375 Defines the Monahans turbo mode to oscillator
376 ratio. Valid values are 1 (default if undefined) and
377 2. The core frequency as calculated above is multiplied
380 - Linux Kernel Interface:
383 U-Boot stores all clock information in Hz
384 internally. For binary compatibility with older Linux
385 kernels (which expect the clocks passed in the
386 bd_info data to be in MHz) the environment variable
387 "clocks_in_mhz" can be defined so that U-Boot
388 converts clock data to MHZ before passing it to the
390 When CONFIG_CLOCKS_IN_MHZ is defined, a definition of
391 "clocks_in_mhz=1" is automatically included in the
394 CONFIG_MEMSIZE_IN_BYTES [relevant for MIPS only]
396 When transferring memsize parameter to linux, some versions
397 expect it to be in bytes, others in MB.
398 Define CONFIG_MEMSIZE_IN_BYTES to make it in bytes.
402 New kernel versions are expecting firmware settings to be
403 passed using flattened device trees (based on open firmware
407 * New libfdt-based support
408 * Adds the "fdt" command
409 * The bootm command automatically updates the fdt
411 OF_CPU - The proper name of the cpus node (only required for
412 MPC512X and MPC5xxx based boards).
413 OF_SOC - The proper name of the soc node (only required for
414 MPC512X and MPC5xxx based boards).
415 OF_TBCLK - The timebase frequency.
416 OF_STDOUT_PATH - The path to the console device
418 boards with QUICC Engines require OF_QE to set UCC MAC
421 CONFIG_OF_BOARD_SETUP
423 Board code has addition modification that it wants to make
424 to the flat device tree before handing it off to the kernel
428 This define fills in the correct boot CPU in the boot
429 param header, the default value is zero if undefined.
433 U-Boot can detect if an IDE device is present or not.
434 If not, and this new config option is activated, U-Boot
435 removes the ATA node from the DTS before booting Linux,
436 so the Linux IDE driver does not probe the device and
437 crash. This is needed for buggy hardware (uc101) where
438 no pull down resistor is connected to the signal IDE5V_DD7.
440 - vxWorks boot parameters:
442 bootvx constructs a valid bootline using the following
443 environments variables: bootfile, ipaddr, serverip, hostname.
444 It loads the vxWorks image pointed bootfile.
446 CONFIG_SYS_VXWORKS_BOOT_DEVICE - The vxworks device name
447 CONFIG_SYS_VXWORKS_MAC_PTR - Ethernet 6 byte MA -address
448 CONFIG_SYS_VXWORKS_SERVERNAME - Name of the server
449 CONFIG_SYS_VXWORKS_BOOT_ADDR - Address of boot parameters
451 CONFIG_SYS_VXWORKS_ADD_PARAMS
453 Add it at the end of the bootline. E.g "u=username pw=secret"
455 Note: If a "bootargs" environment is defined, it will overwride
456 the defaults discussed just above.
461 Define this if you want support for Amba PrimeCell PL010 UARTs.
465 Define this if you want support for Amba PrimeCell PL011 UARTs.
469 If you have Amba PrimeCell PL011 UARTs, set this variable to
470 the clock speed of the UARTs.
474 If you have Amba PrimeCell PL010 or PL011 UARTs on your board,
475 define this to a list of base addresses for each (supported)
476 port. See e.g. include/configs/versatile.h
480 Depending on board, define exactly one serial port
481 (like CONFIG_8xx_CONS_SMC1, CONFIG_8xx_CONS_SMC2,
482 CONFIG_8xx_CONS_SCC1, ...), or switch off the serial
483 console by defining CONFIG_8xx_CONS_NONE
485 Note: if CONFIG_8xx_CONS_NONE is defined, the serial
486 port routines must be defined elsewhere
487 (i.e. serial_init(), serial_getc(), ...)
490 Enables console device for a color framebuffer. Needs following
491 defines (cf. smiLynxEM, i8042, board/eltec/bab7xx)
492 VIDEO_FB_LITTLE_ENDIAN graphic memory organisation
494 VIDEO_HW_RECTFILL graphic chip supports
497 VIDEO_HW_BITBLT graphic chip supports
498 bit-blit (cf. smiLynxEM)
499 VIDEO_VISIBLE_COLS visible pixel columns
501 VIDEO_VISIBLE_ROWS visible pixel rows
502 VIDEO_PIXEL_SIZE bytes per pixel
503 VIDEO_DATA_FORMAT graphic data format
504 (0-5, cf. cfb_console.c)
505 VIDEO_FB_ADRS framebuffer address
506 VIDEO_KBD_INIT_FCT keyboard int fct
507 (i.e. i8042_kbd_init())
508 VIDEO_TSTC_FCT test char fct
510 VIDEO_GETC_FCT get char fct
512 CONFIG_CONSOLE_CURSOR cursor drawing on/off
513 (requires blink timer
515 CONFIG_SYS_CONSOLE_BLINK_COUNT blink interval (cf. i8042.c)
516 CONFIG_CONSOLE_TIME display time/date info in
518 (requires CONFIG_CMD_DATE)
519 CONFIG_VIDEO_LOGO display Linux logo in
521 CONFIG_VIDEO_BMP_LOGO use bmp_logo.h instead of
522 linux_logo.h for logo.
523 Requires CONFIG_VIDEO_LOGO
524 CONFIG_CONSOLE_EXTRA_INFO
525 additional board info beside
528 When CONFIG_CFB_CONSOLE is defined, video console is
529 default i/o. Serial console can be forced with
530 environment 'console=serial'.
532 When CONFIG_SILENT_CONSOLE is defined, all console
533 messages (by U-Boot and Linux!) can be silenced with
534 the "silent" environment variable. See
535 doc/README.silent for more information.
538 CONFIG_BAUDRATE - in bps
539 Select one of the baudrates listed in
540 CONFIG_SYS_BAUDRATE_TABLE, see below.
541 CONFIG_SYS_BRGCLK_PRESCALE, baudrate prescale
543 - Console Rx buffer length
544 With CONFIG_SYS_SMC_RXBUFLEN it is possible to define
545 the maximum receive buffer length for the SMC.
546 This option is actual only for 82xx and 8xx possible.
547 If using CONFIG_SYS_SMC_RXBUFLEN also CONFIG_SYS_MAXIDLE
548 must be defined, to setup the maximum idle timeout for
551 - Boot Delay: CONFIG_BOOTDELAY - in seconds
552 Delay before automatically booting the default image;
553 set to -1 to disable autoboot.
555 See doc/README.autoboot for these options that
556 work with CONFIG_BOOTDELAY. None are required.
557 CONFIG_BOOT_RETRY_TIME
558 CONFIG_BOOT_RETRY_MIN
559 CONFIG_AUTOBOOT_KEYED
560 CONFIG_AUTOBOOT_PROMPT
561 CONFIG_AUTOBOOT_DELAY_STR
562 CONFIG_AUTOBOOT_STOP_STR
563 CONFIG_AUTOBOOT_DELAY_STR2
564 CONFIG_AUTOBOOT_STOP_STR2
565 CONFIG_ZERO_BOOTDELAY_CHECK
566 CONFIG_RESET_TO_RETRY
570 Only needed when CONFIG_BOOTDELAY is enabled;
571 define a command string that is automatically executed
572 when no character is read on the console interface
573 within "Boot Delay" after reset.
576 This can be used to pass arguments to the bootm
577 command. The value of CONFIG_BOOTARGS goes into the
578 environment value "bootargs".
580 CONFIG_RAMBOOT and CONFIG_NFSBOOT
581 The value of these goes into the environment as
582 "ramboot" and "nfsboot" respectively, and can be used
583 as a convenience, when switching between booting from
589 When this option is #defined, the existence of the
590 environment variable "preboot" will be checked
591 immediately before starting the CONFIG_BOOTDELAY
592 countdown and/or running the auto-boot command resp.
593 entering interactive mode.
595 This feature is especially useful when "preboot" is
596 automatically generated or modified. For an example
597 see the LWMON board specific code: here "preboot" is
598 modified when the user holds down a certain
599 combination of keys on the (special) keyboard when
602 - Serial Download Echo Mode:
604 If defined to 1, all characters received during a
605 serial download (using the "loads" command) are
606 echoed back. This might be needed by some terminal
607 emulations (like "cu"), but may as well just take
608 time on others. This setting #define's the initial
609 value of the "loads_echo" environment variable.
611 - Kgdb Serial Baudrate: (if CONFIG_CMD_KGDB is defined)
613 Select one of the baudrates listed in
614 CONFIG_SYS_BAUDRATE_TABLE, see below.
617 Monitor commands can be included or excluded
618 from the build by using the #include files
619 "config_cmd_all.h" and #undef'ing unwanted
620 commands, or using "config_cmd_default.h"
621 and augmenting with additional #define's
624 The default command configuration includes all commands
625 except those marked below with a "*".
627 CONFIG_CMD_ASKENV * ask for env variable
628 CONFIG_CMD_BDI bdinfo
629 CONFIG_CMD_BEDBUG * Include BedBug Debugger
630 CONFIG_CMD_BMP * BMP support
631 CONFIG_CMD_BSP * Board specific commands
632 CONFIG_CMD_BOOTD bootd
633 CONFIG_CMD_CACHE * icache, dcache
634 CONFIG_CMD_CONSOLE coninfo
635 CONFIG_CMD_CRC32 * crc32
636 CONFIG_CMD_DATE * support for RTC, date/time...
637 CONFIG_CMD_DHCP * DHCP support
638 CONFIG_CMD_DIAG * Diagnostics
639 CONFIG_CMD_DS4510 * ds4510 I2C gpio commands
640 CONFIG_CMD_DS4510_INFO * ds4510 I2C info command
641 CONFIG_CMD_DS4510_MEM * ds4510 I2C eeprom/sram commansd
642 CONFIG_CMD_DS4510_RST * ds4510 I2C rst command
643 CONFIG_CMD_DTT * Digital Therm and Thermostat
644 CONFIG_CMD_ECHO echo arguments
645 CONFIG_CMD_EDITENV edit env variable
646 CONFIG_CMD_EEPROM * EEPROM read/write support
647 CONFIG_CMD_ELF * bootelf, bootvx
648 CONFIG_CMD_EXPORTENV * export the environment
649 CONFIG_CMD_SAVEENV saveenv
650 CONFIG_CMD_FDC * Floppy Disk Support
651 CONFIG_CMD_FAT * FAT partition support
652 CONFIG_CMD_FDOS * Dos diskette Support
653 CONFIG_CMD_FLASH flinfo, erase, protect
654 CONFIG_CMD_FPGA FPGA device initialization support
655 CONFIG_CMD_GO * the 'go' command (exec code)
656 CONFIG_CMD_GREPENV * search environment
657 CONFIG_CMD_HWFLOW * RTS/CTS hw flow control
658 CONFIG_CMD_I2C * I2C serial bus support
659 CONFIG_CMD_IDE * IDE harddisk support
660 CONFIG_CMD_IMI iminfo
661 CONFIG_CMD_IMLS List all found images
662 CONFIG_CMD_IMMAP * IMMR dump support
663 CONFIG_CMD_IMPORTENV * import an environment
664 CONFIG_CMD_IRQ * irqinfo
665 CONFIG_CMD_ITEST Integer/string test of 2 values
666 CONFIG_CMD_JFFS2 * JFFS2 Support
667 CONFIG_CMD_KGDB * kgdb
668 CONFIG_CMD_LDRINFO ldrinfo (display Blackfin loader)
669 CONFIG_CMD_LOADB loadb
670 CONFIG_CMD_LOADS loads
671 CONFIG_CMD_MD5SUM print md5 message digest
672 (requires CONFIG_CMD_MEMORY and CONFIG_MD5)
673 CONFIG_CMD_MEMORY md, mm, nm, mw, cp, cmp, crc, base,
675 CONFIG_CMD_MISC Misc functions like sleep etc
676 CONFIG_CMD_MMC * MMC memory mapped support
677 CONFIG_CMD_MII * MII utility commands
678 CONFIG_CMD_MTDPARTS * MTD partition support
679 CONFIG_CMD_NAND * NAND support
680 CONFIG_CMD_NET bootp, tftpboot, rarpboot
681 CONFIG_CMD_PCA953X * PCA953x I2C gpio commands
682 CONFIG_CMD_PCA953X_INFO * PCA953x I2C gpio info command
683 CONFIG_CMD_PCI * pciinfo
684 CONFIG_CMD_PCMCIA * PCMCIA support
685 CONFIG_CMD_PING * send ICMP ECHO_REQUEST to network
687 CONFIG_CMD_PORTIO * Port I/O
688 CONFIG_CMD_REGINFO * Register dump
689 CONFIG_CMD_RUN run command in env variable
690 CONFIG_CMD_SAVES * save S record dump
691 CONFIG_CMD_SCSI * SCSI Support
692 CONFIG_CMD_SDRAM * print SDRAM configuration information
693 (requires CONFIG_CMD_I2C)
694 CONFIG_CMD_SETGETDCR Support for DCR Register access
696 CONFIG_CMD_SHA1SUM print sha1 memory digest
697 (requires CONFIG_CMD_MEMORY)
698 CONFIG_CMD_SOURCE "source" command Support
699 CONFIG_CMD_SPI * SPI serial bus support
700 CONFIG_CMD_USB * USB support
701 CONFIG_CMD_VFD * VFD support (TRAB)
702 CONFIG_CMD_CDP * Cisco Discover Protocol support
703 CONFIG_CMD_FSL * Microblaze FSL support
706 EXAMPLE: If you want all functions except of network
707 support you can write:
709 #include "config_cmd_all.h"
710 #undef CONFIG_CMD_NET
713 fdt (flattened device tree) command: CONFIG_OF_LIBFDT
715 Note: Don't enable the "icache" and "dcache" commands
716 (configuration option CONFIG_CMD_CACHE) unless you know
717 what you (and your U-Boot users) are doing. Data
718 cache cannot be enabled on systems like the 8xx or
719 8260 (where accesses to the IMMR region must be
720 uncached), and it cannot be disabled on all other
721 systems where we (mis-) use the data cache to hold an
722 initial stack and some data.
725 XXX - this list needs to get updated!
729 If this variable is defined, it enables watchdog
730 support. There must be support in the platform specific
731 code for a watchdog. For the 8xx and 8260 CPUs, the
732 SIU Watchdog feature is enabled in the SYPCR
736 CONFIG_VERSION_VARIABLE
737 If this variable is defined, an environment variable
738 named "ver" is created by U-Boot showing the U-Boot
739 version as printed by the "version" command.
740 This variable is readonly.
744 When CONFIG_CMD_DATE is selected, the type of the RTC
745 has to be selected, too. Define exactly one of the
748 CONFIG_RTC_MPC8xx - use internal RTC of MPC8xx
749 CONFIG_RTC_PCF8563 - use Philips PCF8563 RTC
750 CONFIG_RTC_MC13783 - use MC13783 RTC
751 CONFIG_RTC_MC146818 - use MC146818 RTC
752 CONFIG_RTC_DS1307 - use Maxim, Inc. DS1307 RTC
753 CONFIG_RTC_DS1337 - use Maxim, Inc. DS1337 RTC
754 CONFIG_RTC_DS1338 - use Maxim, Inc. DS1338 RTC
755 CONFIG_RTC_DS164x - use Dallas DS164x RTC
756 CONFIG_RTC_ISL1208 - use Intersil ISL1208 RTC
757 CONFIG_RTC_MAX6900 - use Maxim, Inc. MAX6900 RTC
758 CONFIG_SYS_RTC_DS1337_NOOSC - Turn off the OSC output for DS1337
759 CONFIG_SYS_RV3029_TCR - enable trickle charger on
762 Note that if the RTC uses I2C, then the I2C interface
763 must also be configured. See I2C Support, below.
766 CONFIG_PCA953X - use NXP's PCA953X series I2C GPIO
767 CONFIG_PCA953X_INFO - enable pca953x info command
769 The CONFIG_SYS_I2C_PCA953X_WIDTH option specifies a list of
770 chip-ngpio pairs that tell the PCA953X driver the number of
771 pins supported by a particular chip.
773 Note that if the GPIO device uses I2C, then the I2C interface
774 must also be configured. See I2C Support, below.
778 When CONFIG_TIMESTAMP is selected, the timestamp
779 (date and time) of an image is printed by image
780 commands like bootm or iminfo. This option is
781 automatically enabled when you select CONFIG_CMD_DATE .
784 CONFIG_MAC_PARTITION and/or CONFIG_DOS_PARTITION
785 and/or CONFIG_ISO_PARTITION and/or CONFIG_EFI_PARTITION
787 If IDE or SCSI support is enabled (CONFIG_CMD_IDE or
788 CONFIG_CMD_SCSI) you must configure support for at
789 least one partition type as well.
792 CONFIG_IDE_RESET_ROUTINE - this is defined in several
793 board configurations files but used nowhere!
795 CONFIG_IDE_RESET - is this is defined, IDE Reset will
796 be performed by calling the function
797 ide_set_reset(int reset)
798 which has to be defined in a board specific file
803 Set this to enable ATAPI support.
808 Set this to enable support for disks larger than 137GB
809 Also look at CONFIG_SYS_64BIT_LBA.
810 Whithout these , LBA48 support uses 32bit variables and will 'only'
811 support disks up to 2.1TB.
813 CONFIG_SYS_64BIT_LBA:
814 When enabled, makes the IDE subsystem use 64bit sector addresses.
818 At the moment only there is only support for the
819 SYM53C8XX SCSI controller; define
820 CONFIG_SCSI_SYM53C8XX to enable it.
822 CONFIG_SYS_SCSI_MAX_LUN [8], CONFIG_SYS_SCSI_MAX_SCSI_ID [7] and
823 CONFIG_SYS_SCSI_MAX_DEVICE [CONFIG_SYS_SCSI_MAX_SCSI_ID *
824 CONFIG_SYS_SCSI_MAX_LUN] can be adjusted to define the
825 maximum numbers of LUNs, SCSI ID's and target
827 CONFIG_SYS_SCSI_SYM53C8XX_CCF to fix clock timing (80Mhz)
829 - NETWORK Support (PCI):
831 Support for Intel 8254x gigabit chips.
833 CONFIG_E1000_FALLBACK_MAC
834 default MAC for empty EEPROM after production.
837 Support for Intel 82557/82559/82559ER chips.
838 Optional CONFIG_EEPRO100_SROM_WRITE enables EEPROM
839 write routine for first time initialisation.
842 Support for Digital 2114x chips.
843 Optional CONFIG_TULIP_SELECT_MEDIA for board specific
844 modem chip initialisation (KS8761/QS6611).
847 Support for National dp83815 chips.
850 Support for National dp8382[01] gigabit chips.
852 - NETWORK Support (other):
854 CONFIG_DRIVER_AT91EMAC
855 Support for AT91RM9200 EMAC.
858 Define this to use reduced MII inteface
860 CONFIG_DRIVER_AT91EMAC_QUIET
861 If this defined, the driver is quiet.
862 The driver doen't show link status messages.
864 CONFIG_DRIVER_LAN91C96
865 Support for SMSC's LAN91C96 chips.
868 Define this to hold the physical address
869 of the LAN91C96's I/O space
871 CONFIG_LAN91C96_USE_32_BIT
872 Define this to enable 32 bit addressing
874 CONFIG_DRIVER_SMC91111
875 Support for SMSC's LAN91C111 chip
878 Define this to hold the physical address
879 of the device (I/O space)
881 CONFIG_SMC_USE_32_BIT
882 Define this if data bus is 32 bits
884 CONFIG_SMC_USE_IOFUNCS
885 Define this to use i/o functions instead of macros
886 (some hardware wont work with macros)
889 Support for Faraday's FTGMAC100 Gigabit SoC Ethernet
891 CONFIG_FTGMAC100_EGIGA
892 Define this to use GE link update with gigabit PHY.
893 Define this if FTGMAC100 is connected to gigabit PHY.
894 If your system has 10/100 PHY only, it might not occur
895 wrong behavior. Because PHY usually return timeout or
896 useless data when polling gigabit status and gigabit
897 control registers. This behavior won't affect the
898 correctnessof 10/100 link speed update.
901 Support for SMSC's LAN911x and LAN921x chips
904 Define this to hold the physical address
905 of the device (I/O space)
907 CONFIG_SMC911X_32_BIT
908 Define this if data bus is 32 bits
910 CONFIG_SMC911X_16_BIT
911 Define this if data bus is 16 bits. If your processor
912 automatically converts one 32 bit word to two 16 bit
913 words you may also try CONFIG_SMC911X_32_BIT.
916 Support for Renesas on-chip Ethernet controller
918 CONFIG_SH_ETHER_USE_PORT
919 Define the number of ports to be used
921 CONFIG_SH_ETHER_PHY_ADDR
922 Define the ETH PHY's address
924 CONFIG_SH_ETHER_CACHE_WRITEBACK
925 If this option is set, the driver enables cache flush.
928 At the moment only the UHCI host controller is
929 supported (PIP405, MIP405, MPC5200); define
930 CONFIG_USB_UHCI to enable it.
931 define CONFIG_USB_KEYBOARD to enable the USB Keyboard
932 and define CONFIG_USB_STORAGE to enable the USB
935 Supported are USB Keyboards and USB Floppy drives
937 MPC5200 USB requires additional defines:
939 for 528 MHz Clock: 0x0001bbbb
943 for differential drivers: 0x00001000
944 for single ended drivers: 0x00005000
945 for differential drivers on PSC3: 0x00000100
946 for single ended drivers on PSC3: 0x00004100
947 CONFIG_SYS_USB_EVENT_POLL
948 May be defined to allow interrupt polling
949 instead of using asynchronous interrupts
952 Define the below if you wish to use the USB console.
953 Once firmware is rebuilt from a serial console issue the
954 command "setenv stdin usbtty; setenv stdout usbtty" and
955 attach your USB cable. The Unix command "dmesg" should print
956 it has found a new device. The environment variable usbtty
957 can be set to gserial or cdc_acm to enable your device to
958 appear to a USB host as a Linux gserial device or a
959 Common Device Class Abstract Control Model serial device.
960 If you select usbtty = gserial you should be able to enumerate
962 # modprobe usbserial vendor=0xVendorID product=0xProductID
963 else if using cdc_acm, simply setting the environment
964 variable usbtty to be cdc_acm should suffice. The following
965 might be defined in YourBoardName.h
968 Define this to build a UDC device
971 Define this to have a tty type of device available to
972 talk to the UDC device
974 CONFIG_SYS_CONSOLE_IS_IN_ENV
975 Define this if you want stdin, stdout &/or stderr to
979 CONFIG_SYS_USB_EXTC_CLK 0xBLAH
980 Derive USB clock from external clock "blah"
981 - CONFIG_SYS_USB_EXTC_CLK 0x02
983 CONFIG_SYS_USB_BRG_CLK 0xBLAH
984 Derive USB clock from brgclk
985 - CONFIG_SYS_USB_BRG_CLK 0x04
987 If you have a USB-IF assigned VendorID then you may wish to
988 define your own vendor specific values either in BoardName.h
989 or directly in usbd_vendor_info.h. If you don't define
990 CONFIG_USBD_MANUFACTURER, CONFIG_USBD_PRODUCT_NAME,
991 CONFIG_USBD_VENDORID and CONFIG_USBD_PRODUCTID, then U-Boot
992 should pretend to be a Linux device to it's target host.
994 CONFIG_USBD_MANUFACTURER
995 Define this string as the name of your company for
996 - CONFIG_USBD_MANUFACTURER "my company"
998 CONFIG_USBD_PRODUCT_NAME
999 Define this string as the name of your product
1000 - CONFIG_USBD_PRODUCT_NAME "acme usb device"
1002 CONFIG_USBD_VENDORID
1003 Define this as your assigned Vendor ID from the USB
1004 Implementors Forum. This *must* be a genuine Vendor ID
1005 to avoid polluting the USB namespace.
1006 - CONFIG_USBD_VENDORID 0xFFFF
1008 CONFIG_USBD_PRODUCTID
1009 Define this as the unique Product ID
1011 - CONFIG_USBD_PRODUCTID 0xFFFF
1015 The MMC controller on the Intel PXA is supported. To
1016 enable this define CONFIG_MMC. The MMC can be
1017 accessed from the boot prompt by mapping the device
1018 to physical memory similar to flash. Command line is
1019 enabled with CONFIG_CMD_MMC. The MMC driver also works with
1020 the FAT fs. This is enabled with CONFIG_CMD_FAT.
1022 - Journaling Flash filesystem support:
1023 CONFIG_JFFS2_NAND, CONFIG_JFFS2_NAND_OFF, CONFIG_JFFS2_NAND_SIZE,
1024 CONFIG_JFFS2_NAND_DEV
1025 Define these for a default partition on a NAND device
1027 CONFIG_SYS_JFFS2_FIRST_SECTOR,
1028 CONFIG_SYS_JFFS2_FIRST_BANK, CONFIG_SYS_JFFS2_NUM_BANKS
1029 Define these for a default partition on a NOR device
1031 CONFIG_SYS_JFFS_CUSTOM_PART
1032 Define this to create an own partition. You have to provide a
1033 function struct part_info* jffs2_part_info(int part_num)
1035 If you define only one JFFS2 partition you may also want to
1036 #define CONFIG_SYS_JFFS_SINGLE_PART 1
1037 to disable the command chpart. This is the default when you
1038 have not defined a custom partition
1043 Define this to enable standard (PC-Style) keyboard
1047 Standard PC keyboard driver with US (is default) and
1048 GERMAN key layout (switch via environment 'keymap=de') support.
1049 Export function i8042_kbd_init, i8042_tstc and i8042_getc
1050 for cfb_console. Supports cursor blinking.
1055 Define this to enable video support (for output to
1058 CONFIG_VIDEO_CT69000
1060 Enable Chips & Technologies 69000 Video chip
1062 CONFIG_VIDEO_SMI_LYNXEM
1063 Enable Silicon Motion SMI 712/710/810 Video chip. The
1064 video output is selected via environment 'videoout'
1065 (1 = LCD and 2 = CRT). If videoout is undefined, CRT is
1068 For the CT69000 and SMI_LYNXEM drivers, videomode is
1069 selected via environment 'videomode'. Two different ways
1071 - "videomode=num" 'num' is a standard LiLo mode numbers.
1072 Following standard modes are supported (* is default):
1074 Colors 640x480 800x600 1024x768 1152x864 1280x1024
1075 -------------+---------------------------------------------
1076 8 bits | 0x301* 0x303 0x305 0x161 0x307
1077 15 bits | 0x310 0x313 0x316 0x162 0x319
1078 16 bits | 0x311 0x314 0x317 0x163 0x31A
1079 24 bits | 0x312 0x315 0x318 ? 0x31B
1080 -------------+---------------------------------------------
1081 (i.e. setenv videomode 317; saveenv; reset;)
1083 - "videomode=bootargs" all the video parameters are parsed
1084 from the bootargs. (See drivers/video/videomodes.c)
1087 CONFIG_VIDEO_SED13806
1088 Enable Epson SED13806 driver. This driver supports 8bpp
1089 and 16bpp modes defined by CONFIG_VIDEO_SED13806_8BPP
1090 or CONFIG_VIDEO_SED13806_16BPP
1093 Enable the Freescale DIU video driver. Reference boards for
1094 SOCs that have a DIU should define this macro to enable DIU
1095 support, and should also define these other macros:
1101 CONFIG_VIDEO_SW_CURSOR
1102 CONFIG_VGA_AS_SINGLE_DEVICE
1104 CONFIG_VIDEO_BMP_LOGO
1106 The DIU driver will look for the 'monitor' environment variable,
1107 and if defined, enable the DIU as a console during boot. This
1108 variable should be set to one of these values:
1110 '0' Output video to the DVI connector
1111 '1' Output video to the LVDS connector
1112 '2' Output video to the Dual-Link LVDS connector
1117 Define this to enable a custom keyboard support.
1118 This simply calls drv_keyboard_init() which must be
1119 defined in your board-specific files.
1120 The only board using this so far is RBC823.
1122 - LCD Support: CONFIG_LCD
1124 Define this to enable LCD support (for output to LCD
1125 display); also select one of the supported displays
1126 by defining one of these:
1130 HITACHI TX09D70VM1CCA, 3.5", 240x320.
1132 CONFIG_NEC_NL6448AC33:
1134 NEC NL6448AC33-18. Active, color, single scan.
1136 CONFIG_NEC_NL6448BC20
1138 NEC NL6448BC20-08. 6.5", 640x480.
1139 Active, color, single scan.
1141 CONFIG_NEC_NL6448BC33_54
1143 NEC NL6448BC33-54. 10.4", 640x480.
1144 Active, color, single scan.
1148 Sharp 320x240. Active, color, single scan.
1149 It isn't 16x9, and I am not sure what it is.
1151 CONFIG_SHARP_LQ64D341
1153 Sharp LQ64D341 display, 640x480.
1154 Active, color, single scan.
1158 HLD1045 display, 640x480.
1159 Active, color, single scan.
1163 Optrex CBL50840-2 NF-FW 99 22 M5
1165 Hitachi LMG6912RPFC-00T
1169 320x240. Black & white.
1171 Normally display is black on white background; define
1172 CONFIG_SYS_WHITE_ON_BLACK to get it inverted.
1174 - Splash Screen Support: CONFIG_SPLASH_SCREEN
1176 If this option is set, the environment is checked for
1177 a variable "splashimage". If found, the usual display
1178 of logo, copyright and system information on the LCD
1179 is suppressed and the BMP image at the address
1180 specified in "splashimage" is loaded instead. The
1181 console is redirected to the "nulldev", too. This
1182 allows for a "silent" boot where a splash screen is
1183 loaded very quickly after power-on.
1185 CONFIG_SPLASH_SCREEN_ALIGN
1187 If this option is set the splash image can be freely positioned
1188 on the screen. Environment variable "splashpos" specifies the
1189 position as "x,y". If a positive number is given it is used as
1190 number of pixel from left/top. If a negative number is given it
1191 is used as number of pixel from right/bottom. You can also
1192 specify 'm' for centering the image.
1195 setenv splashpos m,m
1196 => image at center of screen
1198 setenv splashpos 30,20
1199 => image at x = 30 and y = 20
1201 setenv splashpos -10,m
1202 => vertically centered image
1203 at x = dspWidth - bmpWidth - 9
1205 - Gzip compressed BMP image support: CONFIG_VIDEO_BMP_GZIP
1207 If this option is set, additionally to standard BMP
1208 images, gzipped BMP images can be displayed via the
1209 splashscreen support or the bmp command.
1211 - Run length encoded BMP image (RLE8) support: CONFIG_VIDEO_BMP_RLE8
1213 If this option is set, 8-bit RLE compressed BMP images
1214 can be displayed via the splashscreen support or the
1217 - Compression support:
1220 If this option is set, support for bzip2 compressed
1221 images is included. If not, only uncompressed and gzip
1222 compressed images are supported.
1224 NOTE: the bzip2 algorithm requires a lot of RAM, so
1225 the malloc area (as defined by CONFIG_SYS_MALLOC_LEN) should
1230 If this option is set, support for lzma compressed
1233 Note: The LZMA algorithm adds between 2 and 4KB of code and it
1234 requires an amount of dynamic memory that is given by the
1237 (1846 + 768 << (lc + lp)) * sizeof(uint16)
1239 Where lc and lp stand for, respectively, Literal context bits
1240 and Literal pos bits.
1242 This value is upper-bounded by 14MB in the worst case. Anyway,
1243 for a ~4MB large kernel image, we have lc=3 and lp=0 for a
1244 total amount of (1846 + 768 << (3 + 0)) * 2 = ~41KB... that is
1245 a very small buffer.
1247 Use the lzmainfo tool to determinate the lc and lp values and
1248 then calculate the amount of needed dynamic memory (ensuring
1249 the appropriate CONFIG_SYS_MALLOC_LEN value).
1254 The address of PHY on MII bus.
1256 CONFIG_PHY_CLOCK_FREQ (ppc4xx)
1258 The clock frequency of the MII bus
1262 If this option is set, support for speed/duplex
1263 detection of gigabit PHY is included.
1265 CONFIG_PHY_RESET_DELAY
1267 Some PHY like Intel LXT971A need extra delay after
1268 reset before any MII register access is possible.
1269 For such PHY, set this option to the usec delay
1270 required. (minimum 300usec for LXT971A)
1272 CONFIG_PHY_CMD_DELAY (ppc4xx)
1274 Some PHY like Intel LXT971A need extra delay after
1275 command issued before MII status register can be read
1285 Define a default value for Ethernet address to use
1286 for the respective Ethernet interface, in case this
1287 is not determined automatically.
1292 Define a default value for the IP address to use for
1293 the default Ethernet interface, in case this is not
1294 determined through e.g. bootp.
1296 - Server IP address:
1299 Defines a default value for the IP address of a TFTP
1300 server to contact when using the "tftboot" command.
1302 CONFIG_KEEP_SERVERADDR
1304 Keeps the server's MAC address, in the env 'serveraddr'
1305 for passing to bootargs (like Linux's netconsole option)
1307 - Multicast TFTP Mode:
1310 Defines whether you want to support multicast TFTP as per
1311 rfc-2090; for example to work with atftp. Lets lots of targets
1312 tftp down the same boot image concurrently. Note: the Ethernet
1313 driver in use must provide a function: mcast() to join/leave a
1316 CONFIG_BOOTP_RANDOM_DELAY
1317 - BOOTP Recovery Mode:
1318 CONFIG_BOOTP_RANDOM_DELAY
1320 If you have many targets in a network that try to
1321 boot using BOOTP, you may want to avoid that all
1322 systems send out BOOTP requests at precisely the same
1323 moment (which would happen for instance at recovery
1324 from a power failure, when all systems will try to
1325 boot, thus flooding the BOOTP server. Defining
1326 CONFIG_BOOTP_RANDOM_DELAY causes a random delay to be
1327 inserted before sending out BOOTP requests. The
1328 following delays are inserted then:
1330 1st BOOTP request: delay 0 ... 1 sec
1331 2nd BOOTP request: delay 0 ... 2 sec
1332 3rd BOOTP request: delay 0 ... 4 sec
1334 BOOTP requests: delay 0 ... 8 sec
1336 - DHCP Advanced Options:
1337 You can fine tune the DHCP functionality by defining
1338 CONFIG_BOOTP_* symbols:
1340 CONFIG_BOOTP_SUBNETMASK
1341 CONFIG_BOOTP_GATEWAY
1342 CONFIG_BOOTP_HOSTNAME
1343 CONFIG_BOOTP_NISDOMAIN
1344 CONFIG_BOOTP_BOOTPATH
1345 CONFIG_BOOTP_BOOTFILESIZE
1348 CONFIG_BOOTP_SEND_HOSTNAME
1349 CONFIG_BOOTP_NTPSERVER
1350 CONFIG_BOOTP_TIMEOFFSET
1351 CONFIG_BOOTP_VENDOREX
1353 CONFIG_BOOTP_SERVERIP - TFTP server will be the serverip
1354 environment variable, not the BOOTP server.
1356 CONFIG_BOOTP_DNS2 - If a DHCP client requests the DNS
1357 serverip from a DHCP server, it is possible that more
1358 than one DNS serverip is offered to the client.
1359 If CONFIG_BOOTP_DNS2 is enabled, the secondary DNS
1360 serverip will be stored in the additional environment
1361 variable "dnsip2". The first DNS serverip is always
1362 stored in the variable "dnsip", when CONFIG_BOOTP_DNS
1365 CONFIG_BOOTP_SEND_HOSTNAME - Some DHCP servers are capable
1366 to do a dynamic update of a DNS server. To do this, they
1367 need the hostname of the DHCP requester.
1368 If CONFIG_BOOTP_SEND_HOSTNAME is defined, the content
1369 of the "hostname" environment variable is passed as
1370 option 12 to the DHCP server.
1372 CONFIG_BOOTP_DHCP_REQUEST_DELAY
1374 A 32bit value in microseconds for a delay between
1375 receiving a "DHCP Offer" and sending the "DHCP Request".
1376 This fixes a problem with certain DHCP servers that don't
1377 respond 100% of the time to a "DHCP request". E.g. On an
1378 AT91RM9200 processor running at 180MHz, this delay needed
1379 to be *at least* 15,000 usec before a Windows Server 2003
1380 DHCP server would reply 100% of the time. I recommend at
1381 least 50,000 usec to be safe. The alternative is to hope
1382 that one of the retries will be successful but note that
1383 the DHCP timeout and retry process takes a longer than
1387 CONFIG_CDP_DEVICE_ID
1389 The device id used in CDP trigger frames.
1391 CONFIG_CDP_DEVICE_ID_PREFIX
1393 A two character string which is prefixed to the MAC address
1398 A printf format string which contains the ascii name of
1399 the port. Normally is set to "eth%d" which sets
1400 eth0 for the first Ethernet, eth1 for the second etc.
1402 CONFIG_CDP_CAPABILITIES
1404 A 32bit integer which indicates the device capabilities;
1405 0x00000010 for a normal host which does not forwards.
1409 An ascii string containing the version of the software.
1413 An ascii string containing the name of the platform.
1417 A 32bit integer sent on the trigger.
1419 CONFIG_CDP_POWER_CONSUMPTION
1421 A 16bit integer containing the power consumption of the
1422 device in .1 of milliwatts.
1424 CONFIG_CDP_APPLIANCE_VLAN_TYPE
1426 A byte containing the id of the VLAN.
1428 - Status LED: CONFIG_STATUS_LED
1430 Several configurations allow to display the current
1431 status using a LED. For instance, the LED will blink
1432 fast while running U-Boot code, stop blinking as
1433 soon as a reply to a BOOTP request was received, and
1434 start blinking slow once the Linux kernel is running
1435 (supported by a status LED driver in the Linux
1436 kernel). Defining CONFIG_STATUS_LED enables this
1439 - CAN Support: CONFIG_CAN_DRIVER
1441 Defining CONFIG_CAN_DRIVER enables CAN driver support
1442 on those systems that support this (optional)
1443 feature, like the TQM8xxL modules.
1445 - I2C Support: CONFIG_HARD_I2C | CONFIG_SOFT_I2C
1447 These enable I2C serial bus commands. Defining either of
1448 (but not both of) CONFIG_HARD_I2C or CONFIG_SOFT_I2C will
1449 include the appropriate I2C driver for the selected CPU.
1451 This will allow you to use i2c commands at the u-boot
1452 command line (as long as you set CONFIG_CMD_I2C in
1453 CONFIG_COMMANDS) and communicate with i2c based realtime
1454 clock chips. See common/cmd_i2c.c for a description of the
1455 command line interface.
1457 CONFIG_HARD_I2C selects a hardware I2C controller.
1459 CONFIG_SOFT_I2C configures u-boot to use a software (aka
1460 bit-banging) driver instead of CPM or similar hardware
1463 There are several other quantities that must also be
1464 defined when you define CONFIG_HARD_I2C or CONFIG_SOFT_I2C.
1466 In both cases you will need to define CONFIG_SYS_I2C_SPEED
1467 to be the frequency (in Hz) at which you wish your i2c bus
1468 to run and CONFIG_SYS_I2C_SLAVE to be the address of this node (ie
1469 the CPU's i2c node address).
1471 Now, the u-boot i2c code for the mpc8xx
1472 (arch/powerpc/cpu/mpc8xx/i2c.c) sets the CPU up as a master node
1473 and so its address should therefore be cleared to 0 (See,
1474 eg, MPC823e User's Manual p.16-473). So, set
1475 CONFIG_SYS_I2C_SLAVE to 0.
1477 CONFIG_SYS_I2C_INIT_MPC5XXX
1479 When a board is reset during an i2c bus transfer
1480 chips might think that the current transfer is still
1481 in progress. Reset the slave devices by sending start
1482 commands until the slave device responds.
1484 That's all that's required for CONFIG_HARD_I2C.
1486 If you use the software i2c interface (CONFIG_SOFT_I2C)
1487 then the following macros need to be defined (examples are
1488 from include/configs/lwmon.h):
1492 (Optional). Any commands necessary to enable the I2C
1493 controller or configure ports.
1495 eg: #define I2C_INIT (immr->im_cpm.cp_pbdir |= PB_SCL)
1499 (Only for MPC8260 CPU). The I/O port to use (the code
1500 assumes both bits are on the same port). Valid values
1501 are 0..3 for ports A..D.
1505 The code necessary to make the I2C data line active
1506 (driven). If the data line is open collector, this
1509 eg: #define I2C_ACTIVE (immr->im_cpm.cp_pbdir |= PB_SDA)
1513 The code necessary to make the I2C data line tri-stated
1514 (inactive). If the data line is open collector, this
1517 eg: #define I2C_TRISTATE (immr->im_cpm.cp_pbdir &= ~PB_SDA)
1521 Code that returns TRUE if the I2C data line is high,
1524 eg: #define I2C_READ ((immr->im_cpm.cp_pbdat & PB_SDA) != 0)
1528 If <bit> is TRUE, sets the I2C data line high. If it
1529 is FALSE, it clears it (low).
1531 eg: #define I2C_SDA(bit) \
1532 if(bit) immr->im_cpm.cp_pbdat |= PB_SDA; \
1533 else immr->im_cpm.cp_pbdat &= ~PB_SDA
1537 If <bit> is TRUE, sets the I2C clock line high. If it
1538 is FALSE, it clears it (low).
1540 eg: #define I2C_SCL(bit) \
1541 if(bit) immr->im_cpm.cp_pbdat |= PB_SCL; \
1542 else immr->im_cpm.cp_pbdat &= ~PB_SCL
1546 This delay is invoked four times per clock cycle so this
1547 controls the rate of data transfer. The data rate thus
1548 is 1 / (I2C_DELAY * 4). Often defined to be something
1551 #define I2C_DELAY udelay(2)
1553 CONFIG_SOFT_I2C_GPIO_SCL / CONFIG_SOFT_I2C_GPIO_SDA
1555 If your arch supports the generic GPIO framework (asm/gpio.h),
1556 then you may alternatively define the two GPIOs that are to be
1557 used as SCL / SDA. Any of the previous I2C_xxx macros will
1558 have GPIO-based defaults assigned to them as appropriate.
1560 You should define these to the GPIO value as given directly to
1561 the generic GPIO functions.
1563 CONFIG_SYS_I2C_INIT_BOARD
1565 When a board is reset during an i2c bus transfer
1566 chips might think that the current transfer is still
1567 in progress. On some boards it is possible to access
1568 the i2c SCLK line directly, either by using the
1569 processor pin as a GPIO or by having a second pin
1570 connected to the bus. If this option is defined a
1571 custom i2c_init_board() routine in boards/xxx/board.c
1572 is run early in the boot sequence.
1574 CONFIG_SYS_I2C_BOARD_LATE_INIT
1576 An alternative to CONFIG_SYS_I2C_INIT_BOARD. If this option is
1577 defined a custom i2c_board_late_init() routine in
1578 boards/xxx/board.c is run AFTER the operations in i2c_init()
1579 is completed. This callpoint can be used to unreset i2c bus
1580 using CPU i2c controller register accesses for CPUs whose i2c
1581 controller provide such a method. It is called at the end of
1582 i2c_init() to allow i2c_init operations to setup the i2c bus
1583 controller on the CPU (e.g. setting bus speed & slave address).
1585 CONFIG_I2CFAST (PPC405GP|PPC405EP only)
1587 This option enables configuration of bi_iic_fast[] flags
1588 in u-boot bd_info structure based on u-boot environment
1589 variable "i2cfast". (see also i2cfast)
1591 CONFIG_I2C_MULTI_BUS
1593 This option allows the use of multiple I2C buses, each of which
1594 must have a controller. At any point in time, only one bus is
1595 active. To switch to a different bus, use the 'i2c dev' command.
1596 Note that bus numbering is zero-based.
1598 CONFIG_SYS_I2C_NOPROBES
1600 This option specifies a list of I2C devices that will be skipped
1601 when the 'i2c probe' command is issued. If CONFIG_I2C_MULTI_BUS
1602 is set, specify a list of bus-device pairs. Otherwise, specify
1603 a 1D array of device addresses
1606 #undef CONFIG_I2C_MULTI_BUS
1607 #define CONFIG_SYS_I2C_NOPROBES {0x50,0x68}
1609 will skip addresses 0x50 and 0x68 on a board with one I2C bus
1611 #define CONFIG_I2C_MULTI_BUS
1612 #define CONFIG_SYS_I2C_MULTI_NOPROBES {{0,0x50},{0,0x68},{1,0x54}}
1614 will skip addresses 0x50 and 0x68 on bus 0 and address 0x54 on bus 1
1616 CONFIG_SYS_SPD_BUS_NUM
1618 If defined, then this indicates the I2C bus number for DDR SPD.
1619 If not defined, then U-Boot assumes that SPD is on I2C bus 0.
1621 CONFIG_SYS_RTC_BUS_NUM
1623 If defined, then this indicates the I2C bus number for the RTC.
1624 If not defined, then U-Boot assumes that RTC is on I2C bus 0.
1626 CONFIG_SYS_DTT_BUS_NUM
1628 If defined, then this indicates the I2C bus number for the DTT.
1629 If not defined, then U-Boot assumes that DTT is on I2C bus 0.
1631 CONFIG_SYS_I2C_DTT_ADDR:
1633 If defined, specifies the I2C address of the DTT device.
1634 If not defined, then U-Boot uses predefined value for
1635 specified DTT device.
1639 Define this option if you want to use Freescale's I2C driver in
1640 drivers/i2c/fsl_i2c.c.
1644 Define this option if you have I2C devices reached over 1 .. n
1645 I2C Muxes like the pca9544a. This option addes a new I2C
1646 Command "i2c bus [muxtype:muxaddr:muxchannel]" which adds a
1647 new I2C Bus to the existing I2C Busses. If you select the
1648 new Bus with "i2c dev", u-bbot sends first the commandos for
1649 the muxes to activate this new "bus".
1651 CONFIG_I2C_MULTI_BUS must be also defined, to use this
1655 Adding a new I2C Bus reached over 2 pca9544a muxes
1656 The First mux with address 70 and channel 6
1657 The Second mux with address 71 and channel 4
1659 => i2c bus pca9544a:70:6:pca9544a:71:4
1661 Use the "i2c bus" command without parameter, to get a list
1662 of I2C Busses with muxes:
1665 Busses reached over muxes:
1667 reached over Mux(es):
1670 reached over Mux(es):
1675 If you now switch to the new I2C Bus 3 with "i2c dev 3"
1676 u-boot sends First the Commando to the mux@70 to enable
1677 channel 6, and then the Commando to the mux@71 to enable
1680 After that, you can use the "normal" i2c commands as
1681 usual, to communicate with your I2C devices behind
1684 This option is actually implemented for the bitbanging
1685 algorithm in common/soft_i2c.c and for the Hardware I2C
1686 Bus on the MPC8260. But it should be not so difficult
1687 to add this option to other architectures.
1689 CONFIG_SOFT_I2C_READ_REPEATED_START
1691 defining this will force the i2c_read() function in
1692 the soft_i2c driver to perform an I2C repeated start
1693 between writing the address pointer and reading the
1694 data. If this define is omitted the default behaviour
1695 of doing a stop-start sequence will be used. Most I2C
1696 devices can use either method, but some require one or
1699 - SPI Support: CONFIG_SPI
1701 Enables SPI driver (so far only tested with
1702 SPI EEPROM, also an instance works with Crystal A/D and
1703 D/As on the SACSng board)
1707 Enables the driver for SPI controller on SuperH. Currently
1708 only SH7757 is supported.
1712 Enables extended (16-bit) SPI EEPROM addressing.
1713 (symmetrical to CONFIG_I2C_X)
1717 Enables a software (bit-bang) SPI driver rather than
1718 using hardware support. This is a general purpose
1719 driver that only requires three general I/O port pins
1720 (two outputs, one input) to function. If this is
1721 defined, the board configuration must define several
1722 SPI configuration items (port pins to use, etc). For
1723 an example, see include/configs/sacsng.h.
1727 Enables a hardware SPI driver for general-purpose reads
1728 and writes. As with CONFIG_SOFT_SPI, the board configuration
1729 must define a list of chip-select function pointers.
1730 Currently supported on some MPC8xxx processors. For an
1731 example, see include/configs/mpc8349emds.h.
1735 Enables the driver for the SPI controllers on i.MX and MXC
1736 SoCs. Currently only i.MX31 is supported.
1738 - FPGA Support: CONFIG_FPGA
1740 Enables FPGA subsystem.
1742 CONFIG_FPGA_<vendor>
1744 Enables support for specific chip vendors.
1747 CONFIG_FPGA_<family>
1749 Enables support for FPGA family.
1750 (SPARTAN2, SPARTAN3, VIRTEX2, CYCLONE2, ACEX1K, ACEX)
1754 Specify the number of FPGA devices to support.
1756 CONFIG_SYS_FPGA_PROG_FEEDBACK
1758 Enable printing of hash marks during FPGA configuration.
1760 CONFIG_SYS_FPGA_CHECK_BUSY
1762 Enable checks on FPGA configuration interface busy
1763 status by the configuration function. This option
1764 will require a board or device specific function to
1769 If defined, a function that provides delays in the FPGA
1770 configuration driver.
1772 CONFIG_SYS_FPGA_CHECK_CTRLC
1773 Allow Control-C to interrupt FPGA configuration
1775 CONFIG_SYS_FPGA_CHECK_ERROR
1777 Check for configuration errors during FPGA bitfile
1778 loading. For example, abort during Virtex II
1779 configuration if the INIT_B line goes low (which
1780 indicated a CRC error).
1782 CONFIG_SYS_FPGA_WAIT_INIT
1784 Maximum time to wait for the INIT_B line to deassert
1785 after PROB_B has been deasserted during a Virtex II
1786 FPGA configuration sequence. The default time is 500
1789 CONFIG_SYS_FPGA_WAIT_BUSY
1791 Maximum time to wait for BUSY to deassert during
1792 Virtex II FPGA configuration. The default is 5 ms.
1794 CONFIG_SYS_FPGA_WAIT_CONFIG
1796 Time to wait after FPGA configuration. The default is
1799 - Configuration Management:
1802 If defined, this string will be added to the U-Boot
1803 version information (U_BOOT_VERSION)
1805 - Vendor Parameter Protection:
1807 U-Boot considers the values of the environment
1808 variables "serial#" (Board Serial Number) and
1809 "ethaddr" (Ethernet Address) to be parameters that
1810 are set once by the board vendor / manufacturer, and
1811 protects these variables from casual modification by
1812 the user. Once set, these variables are read-only,
1813 and write or delete attempts are rejected. You can
1814 change this behaviour:
1816 If CONFIG_ENV_OVERWRITE is #defined in your config
1817 file, the write protection for vendor parameters is
1818 completely disabled. Anybody can change or delete
1821 Alternatively, if you #define _both_ CONFIG_ETHADDR
1822 _and_ CONFIG_OVERWRITE_ETHADDR_ONCE, a default
1823 Ethernet address is installed in the environment,
1824 which can be changed exactly ONCE by the user. [The
1825 serial# is unaffected by this, i. e. it remains
1831 Define this variable to enable the reservation of
1832 "protected RAM", i. e. RAM which is not overwritten
1833 by U-Boot. Define CONFIG_PRAM to hold the number of
1834 kB you want to reserve for pRAM. You can overwrite
1835 this default value by defining an environment
1836 variable "pram" to the number of kB you want to
1837 reserve. Note that the board info structure will
1838 still show the full amount of RAM. If pRAM is
1839 reserved, a new environment variable "mem" will
1840 automatically be defined to hold the amount of
1841 remaining RAM in a form that can be passed as boot
1842 argument to Linux, for instance like that:
1844 setenv bootargs ... mem=\${mem}
1847 This way you can tell Linux not to use this memory,
1848 either, which results in a memory region that will
1849 not be affected by reboots.
1851 *WARNING* If your board configuration uses automatic
1852 detection of the RAM size, you must make sure that
1853 this memory test is non-destructive. So far, the
1854 following board configurations are known to be
1857 ETX094, IVMS8, IVML24, SPD8xx, TQM8xxL,
1858 HERMES, IP860, RPXlite, LWMON, LANTEC,
1864 Define this variable to stop the system in case of a
1865 fatal error, so that you have to reset it manually.
1866 This is probably NOT a good idea for an embedded
1867 system where you want the system to reboot
1868 automatically as fast as possible, but it may be
1869 useful during development since you can try to debug
1870 the conditions that lead to the situation.
1872 CONFIG_NET_RETRY_COUNT
1874 This variable defines the number of retries for
1875 network operations like ARP, RARP, TFTP, or BOOTP
1876 before giving up the operation. If not defined, a
1877 default value of 5 is used.
1881 Timeout waiting for an ARP reply in milliseconds.
1883 - Command Interpreter:
1884 CONFIG_AUTO_COMPLETE
1886 Enable auto completion of commands using TAB.
1888 Note that this feature has NOT been implemented yet
1889 for the "hush" shell.
1892 CONFIG_SYS_HUSH_PARSER
1894 Define this variable to enable the "hush" shell (from
1895 Busybox) as command line interpreter, thus enabling
1896 powerful command line syntax like
1897 if...then...else...fi conditionals or `&&' and '||'
1898 constructs ("shell scripts").
1900 If undefined, you get the old, much simpler behaviour
1901 with a somewhat smaller memory footprint.
1904 CONFIG_SYS_PROMPT_HUSH_PS2
1906 This defines the secondary prompt string, which is
1907 printed when the command interpreter needs more input
1908 to complete a command. Usually "> ".
1912 In the current implementation, the local variables
1913 space and global environment variables space are
1914 separated. Local variables are those you define by
1915 simply typing `name=value'. To access a local
1916 variable later on, you have write `$name' or
1917 `${name}'; to execute the contents of a variable
1918 directly type `$name' at the command prompt.
1920 Global environment variables are those you use
1921 setenv/printenv to work with. To run a command stored
1922 in such a variable, you need to use the run command,
1923 and you must not use the '$' sign to access them.
1925 To store commands and special characters in a
1926 variable, please use double quotation marks
1927 surrounding the whole text of the variable, instead
1928 of the backslashes before semicolons and special
1931 - Commandline Editing and History:
1932 CONFIG_CMDLINE_EDITING
1934 Enable editing and History functions for interactive
1935 commandline input operations
1937 - Default Environment:
1938 CONFIG_EXTRA_ENV_SETTINGS
1940 Define this to contain any number of null terminated
1941 strings (variable = value pairs) that will be part of
1942 the default environment compiled into the boot image.
1944 For example, place something like this in your
1945 board's config file:
1947 #define CONFIG_EXTRA_ENV_SETTINGS \
1951 Warning: This method is based on knowledge about the
1952 internal format how the environment is stored by the
1953 U-Boot code. This is NOT an official, exported
1954 interface! Although it is unlikely that this format
1955 will change soon, there is no guarantee either.
1956 You better know what you are doing here.
1958 Note: overly (ab)use of the default environment is
1959 discouraged. Make sure to check other ways to preset
1960 the environment like the "source" command or the
1963 - DataFlash Support:
1964 CONFIG_HAS_DATAFLASH
1966 Defining this option enables DataFlash features and
1967 allows to read/write in Dataflash via the standard
1970 - SystemACE Support:
1973 Adding this option adds support for Xilinx SystemACE
1974 chips attached via some sort of local bus. The address
1975 of the chip must also be defined in the
1976 CONFIG_SYS_SYSTEMACE_BASE macro. For example:
1978 #define CONFIG_SYSTEMACE
1979 #define CONFIG_SYS_SYSTEMACE_BASE 0xf0000000
1981 When SystemACE support is added, the "ace" device type
1982 becomes available to the fat commands, i.e. fatls.
1984 - TFTP Fixed UDP Port:
1987 If this is defined, the environment variable tftpsrcp
1988 is used to supply the TFTP UDP source port value.
1989 If tftpsrcp isn't defined, the normal pseudo-random port
1990 number generator is used.
1992 Also, the environment variable tftpdstp is used to supply
1993 the TFTP UDP destination port value. If tftpdstp isn't
1994 defined, the normal port 69 is used.
1996 The purpose for tftpsrcp is to allow a TFTP server to
1997 blindly start the TFTP transfer using the pre-configured
1998 target IP address and UDP port. This has the effect of
1999 "punching through" the (Windows XP) firewall, allowing
2000 the remainder of the TFTP transfer to proceed normally.
2001 A better solution is to properly configure the firewall,
2002 but sometimes that is not allowed.
2004 - Show boot progress:
2005 CONFIG_SHOW_BOOT_PROGRESS
2007 Defining this option allows to add some board-
2008 specific code (calling a user-provided function
2009 "show_boot_progress(int)") that enables you to show
2010 the system's boot progress on some display (for
2011 example, some LED's) on your board. At the moment,
2012 the following checkpoints are implemented:
2014 - Standalone program support:
2015 CONFIG_STANDALONE_LOAD_ADDR
2017 This option allows to define board specific values
2018 for the address where standalone program gets loaded,
2019 thus overwriting the architecutre dependent default
2022 - Frame Buffer Address:
2025 Define CONFIG_FB_ADDR if you want to use specific address for
2027 Then system will reserve the frame buffer address to defined address
2028 instead of lcd_setmem (this function grab the memory for frame buffer
2031 Please see board_init_f function.
2033 If you want this config option then,
2034 please define it at your board config file
2036 Legacy uImage format:
2039 1 common/cmd_bootm.c before attempting to boot an image
2040 -1 common/cmd_bootm.c Image header has bad magic number
2041 2 common/cmd_bootm.c Image header has correct magic number
2042 -2 common/cmd_bootm.c Image header has bad checksum
2043 3 common/cmd_bootm.c Image header has correct checksum
2044 -3 common/cmd_bootm.c Image data has bad checksum
2045 4 common/cmd_bootm.c Image data has correct checksum
2046 -4 common/cmd_bootm.c Image is for unsupported architecture
2047 5 common/cmd_bootm.c Architecture check OK
2048 -5 common/cmd_bootm.c Wrong Image Type (not kernel, multi)
2049 6 common/cmd_bootm.c Image Type check OK
2050 -6 common/cmd_bootm.c gunzip uncompression error
2051 -7 common/cmd_bootm.c Unimplemented compression type
2052 7 common/cmd_bootm.c Uncompression OK
2053 8 common/cmd_bootm.c No uncompress/copy overwrite error
2054 -9 common/cmd_bootm.c Unsupported OS (not Linux, BSD, VxWorks, QNX)
2056 9 common/image.c Start initial ramdisk verification
2057 -10 common/image.c Ramdisk header has bad magic number
2058 -11 common/image.c Ramdisk header has bad checksum
2059 10 common/image.c Ramdisk header is OK
2060 -12 common/image.c Ramdisk data has bad checksum
2061 11 common/image.c Ramdisk data has correct checksum
2062 12 common/image.c Ramdisk verification complete, start loading
2063 -13 common/image.c Wrong Image Type (not PPC Linux ramdisk)
2064 13 common/image.c Start multifile image verification
2065 14 common/image.c No initial ramdisk, no multifile, continue.
2067 15 arch/<arch>/lib/bootm.c All preparation done, transferring control to OS
2069 -30 arch/powerpc/lib/board.c Fatal error, hang the system
2070 -31 post/post.c POST test failed, detected by post_output_backlog()
2071 -32 post/post.c POST test failed, detected by post_run_single()
2073 34 common/cmd_doc.c before loading a Image from a DOC device
2074 -35 common/cmd_doc.c Bad usage of "doc" command
2075 35 common/cmd_doc.c correct usage of "doc" command
2076 -36 common/cmd_doc.c No boot device
2077 36 common/cmd_doc.c correct boot device
2078 -37 common/cmd_doc.c Unknown Chip ID on boot device
2079 37 common/cmd_doc.c correct chip ID found, device available
2080 -38 common/cmd_doc.c Read Error on boot device
2081 38 common/cmd_doc.c reading Image header from DOC device OK
2082 -39 common/cmd_doc.c Image header has bad magic number
2083 39 common/cmd_doc.c Image header has correct magic number
2084 -40 common/cmd_doc.c Error reading Image from DOC device
2085 40 common/cmd_doc.c Image header has correct magic number
2086 41 common/cmd_ide.c before loading a Image from a IDE device
2087 -42 common/cmd_ide.c Bad usage of "ide" command
2088 42 common/cmd_ide.c correct usage of "ide" command
2089 -43 common/cmd_ide.c No boot device
2090 43 common/cmd_ide.c boot device found
2091 -44 common/cmd_ide.c Device not available
2092 44 common/cmd_ide.c Device available
2093 -45 common/cmd_ide.c wrong partition selected
2094 45 common/cmd_ide.c partition selected
2095 -46 common/cmd_ide.c Unknown partition table
2096 46 common/cmd_ide.c valid partition table found
2097 -47 common/cmd_ide.c Invalid partition type
2098 47 common/cmd_ide.c correct partition type
2099 -48 common/cmd_ide.c Error reading Image Header on boot device
2100 48 common/cmd_ide.c reading Image Header from IDE device OK
2101 -49 common/cmd_ide.c Image header has bad magic number
2102 49 common/cmd_ide.c Image header has correct magic number
2103 -50 common/cmd_ide.c Image header has bad checksum
2104 50 common/cmd_ide.c Image header has correct checksum
2105 -51 common/cmd_ide.c Error reading Image from IDE device
2106 51 common/cmd_ide.c reading Image from IDE device OK
2107 52 common/cmd_nand.c before loading a Image from a NAND device
2108 -53 common/cmd_nand.c Bad usage of "nand" command
2109 53 common/cmd_nand.c correct usage of "nand" command
2110 -54 common/cmd_nand.c No boot device
2111 54 common/cmd_nand.c boot device found
2112 -55 common/cmd_nand.c Unknown Chip ID on boot device
2113 55 common/cmd_nand.c correct chip ID found, device available
2114 -56 common/cmd_nand.c Error reading Image Header on boot device
2115 56 common/cmd_nand.c reading Image Header from NAND device OK
2116 -57 common/cmd_nand.c Image header has bad magic number
2117 57 common/cmd_nand.c Image header has correct magic number
2118 -58 common/cmd_nand.c Error reading Image from NAND device
2119 58 common/cmd_nand.c reading Image from NAND device OK
2121 -60 common/env_common.c Environment has a bad CRC, using default
2123 64 net/eth.c starting with Ethernet configuration.
2124 -64 net/eth.c no Ethernet found.
2125 65 net/eth.c Ethernet found.
2127 -80 common/cmd_net.c usage wrong
2128 80 common/cmd_net.c before calling NetLoop()
2129 -81 common/cmd_net.c some error in NetLoop() occurred
2130 81 common/cmd_net.c NetLoop() back without error
2131 -82 common/cmd_net.c size == 0 (File with size 0 loaded)
2132 82 common/cmd_net.c trying automatic boot
2133 83 common/cmd_net.c running "source" command
2134 -83 common/cmd_net.c some error in automatic boot or "source" command
2135 84 common/cmd_net.c end without errors
2140 100 common/cmd_bootm.c Kernel FIT Image has correct format
2141 -100 common/cmd_bootm.c Kernel FIT Image has incorrect format
2142 101 common/cmd_bootm.c No Kernel subimage unit name, using configuration
2143 -101 common/cmd_bootm.c Can't get configuration for kernel subimage
2144 102 common/cmd_bootm.c Kernel unit name specified
2145 -103 common/cmd_bootm.c Can't get kernel subimage node offset
2146 103 common/cmd_bootm.c Found configuration node
2147 104 common/cmd_bootm.c Got kernel subimage node offset
2148 -104 common/cmd_bootm.c Kernel subimage hash verification failed
2149 105 common/cmd_bootm.c Kernel subimage hash verification OK
2150 -105 common/cmd_bootm.c Kernel subimage is for unsupported architecture
2151 106 common/cmd_bootm.c Architecture check OK
2152 -106 common/cmd_bootm.c Kernel subimage has wrong type
2153 107 common/cmd_bootm.c Kernel subimage type OK
2154 -107 common/cmd_bootm.c Can't get kernel subimage data/size
2155 108 common/cmd_bootm.c Got kernel subimage data/size
2156 -108 common/cmd_bootm.c Wrong image type (not legacy, FIT)
2157 -109 common/cmd_bootm.c Can't get kernel subimage type
2158 -110 common/cmd_bootm.c Can't get kernel subimage comp
2159 -111 common/cmd_bootm.c Can't get kernel subimage os
2160 -112 common/cmd_bootm.c Can't get kernel subimage load address
2161 -113 common/cmd_bootm.c Image uncompress/copy overwrite error
2163 120 common/image.c Start initial ramdisk verification
2164 -120 common/image.c Ramdisk FIT image has incorrect format
2165 121 common/image.c Ramdisk FIT image has correct format
2166 122 common/image.c No ramdisk subimage unit name, using configuration
2167 -122 common/image.c Can't get configuration for ramdisk subimage
2168 123 common/image.c Ramdisk unit name specified
2169 -124 common/image.c Can't get ramdisk subimage node offset
2170 125 common/image.c Got ramdisk subimage node offset
2171 -125 common/image.c Ramdisk subimage hash verification failed
2172 126 common/image.c Ramdisk subimage hash verification OK
2173 -126 common/image.c Ramdisk subimage for unsupported architecture
2174 127 common/image.c Architecture check OK
2175 -127 common/image.c Can't get ramdisk subimage data/size
2176 128 common/image.c Got ramdisk subimage data/size
2177 129 common/image.c Can't get ramdisk load address
2178 -129 common/image.c Got ramdisk load address
2180 -130 common/cmd_doc.c Incorrect FIT image format
2181 131 common/cmd_doc.c FIT image format OK
2183 -140 common/cmd_ide.c Incorrect FIT image format
2184 141 common/cmd_ide.c FIT image format OK
2186 -150 common/cmd_nand.c Incorrect FIT image format
2187 151 common/cmd_nand.c FIT image format OK
2189 - Automatic software updates via TFTP server
2191 CONFIG_UPDATE_TFTP_CNT_MAX
2192 CONFIG_UPDATE_TFTP_MSEC_MAX
2194 These options enable and control the auto-update feature;
2195 for a more detailed description refer to doc/README.update.
2197 - MTD Support (mtdparts command, UBI support)
2200 Adds the MTD device infrastructure from the Linux kernel.
2201 Needed for mtdparts command support.
2203 CONFIG_MTD_PARTITIONS
2205 Adds the MTD partitioning infrastructure from the Linux
2206 kernel. Needed for UBI support.
2212 [so far only for SMDK2400 and TRAB boards]
2214 - Modem support enable:
2215 CONFIG_MODEM_SUPPORT
2217 - RTS/CTS Flow control enable:
2220 - Modem debug support:
2221 CONFIG_MODEM_SUPPORT_DEBUG
2223 Enables debugging stuff (char screen[1024], dbg())
2224 for modem support. Useful only with BDI2000.
2226 - Interrupt support (PPC):
2228 There are common interrupt_init() and timer_interrupt()
2229 for all PPC archs. interrupt_init() calls interrupt_init_cpu()
2230 for CPU specific initialization. interrupt_init_cpu()
2231 should set decrementer_count to appropriate value. If
2232 CPU resets decrementer automatically after interrupt
2233 (ppc4xx) it should set decrementer_count to zero.
2234 timer_interrupt() calls timer_interrupt_cpu() for CPU
2235 specific handling. If board has watchdog / status_led
2236 / other_activity_monitor it works automatically from
2237 general timer_interrupt().
2241 In the target system modem support is enabled when a
2242 specific key (key combination) is pressed during
2243 power-on. Otherwise U-Boot will boot normally
2244 (autoboot). The key_pressed() function is called from
2245 board_init(). Currently key_pressed() is a dummy
2246 function, returning 1 and thus enabling modem
2249 If there are no modem init strings in the
2250 environment, U-Boot proceed to autoboot; the
2251 previous output (banner, info printfs) will be
2254 See also: doc/README.Modem
2257 Configuration Settings:
2258 -----------------------
2260 - CONFIG_SYS_LONGHELP: Defined when you want long help messages included;
2261 undefine this when you're short of memory.
2263 - CONFIG_SYS_HELP_CMD_WIDTH: Defined when you want to override the default
2264 width of the commands listed in the 'help' command output.
2266 - CONFIG_SYS_PROMPT: This is what U-Boot prints on the console to
2267 prompt for user input.
2269 - CONFIG_SYS_CBSIZE: Buffer size for input from the Console
2271 - CONFIG_SYS_PBSIZE: Buffer size for Console output
2273 - CONFIG_SYS_MAXARGS: max. Number of arguments accepted for monitor commands
2275 - CONFIG_SYS_BARGSIZE: Buffer size for Boot Arguments which are passed to
2276 the application (usually a Linux kernel) when it is
2279 - CONFIG_SYS_BAUDRATE_TABLE:
2280 List of legal baudrate settings for this board.
2282 - CONFIG_SYS_CONSOLE_INFO_QUIET
2283 Suppress display of console information at boot.
2285 - CONFIG_SYS_CONSOLE_IS_IN_ENV
2286 If the board specific function
2287 extern int overwrite_console (void);
2288 returns 1, the stdin, stderr and stdout are switched to the
2289 serial port, else the settings in the environment are used.
2291 - CONFIG_SYS_CONSOLE_OVERWRITE_ROUTINE
2292 Enable the call to overwrite_console().
2294 - CONFIG_SYS_CONSOLE_ENV_OVERWRITE
2295 Enable overwrite of previous console environment settings.
2297 - CONFIG_SYS_MEMTEST_START, CONFIG_SYS_MEMTEST_END:
2298 Begin and End addresses of the area used by the
2301 - CONFIG_SYS_ALT_MEMTEST:
2302 Enable an alternate, more extensive memory test.
2304 - CONFIG_SYS_MEMTEST_SCRATCH:
2305 Scratch address used by the alternate memory test
2306 You only need to set this if address zero isn't writeable
2308 - CONFIG_SYS_MEM_TOP_HIDE (PPC only):
2309 If CONFIG_SYS_MEM_TOP_HIDE is defined in the board config header,
2310 this specified memory area will get subtracted from the top
2311 (end) of RAM and won't get "touched" at all by U-Boot. By
2312 fixing up gd->ram_size the Linux kernel should gets passed
2313 the now "corrected" memory size and won't touch it either.
2314 This should work for arch/ppc and arch/powerpc. Only Linux
2315 board ports in arch/powerpc with bootwrapper support that
2316 recalculate the memory size from the SDRAM controller setup
2317 will have to get fixed in Linux additionally.
2319 This option can be used as a workaround for the 440EPx/GRx
2320 CHIP 11 errata where the last 256 bytes in SDRAM shouldn't
2323 WARNING: Please make sure that this value is a multiple of
2324 the Linux page size (normally 4k). If this is not the case,
2325 then the end address of the Linux memory will be located at a
2326 non page size aligned address and this could cause major
2329 - CONFIG_SYS_TFTP_LOADADDR:
2330 Default load address for network file downloads
2332 - CONFIG_SYS_LOADS_BAUD_CHANGE:
2333 Enable temporary baudrate change while serial download
2335 - CONFIG_SYS_SDRAM_BASE:
2336 Physical start address of SDRAM. _Must_ be 0 here.
2338 - CONFIG_SYS_MBIO_BASE:
2339 Physical start address of Motherboard I/O (if using a
2342 - CONFIG_SYS_FLASH_BASE:
2343 Physical start address of Flash memory.
2345 - CONFIG_SYS_MONITOR_BASE:
2346 Physical start address of boot monitor code (set by
2347 make config files to be same as the text base address
2348 (CONFIG_SYS_TEXT_BASE) used when linking) - same as
2349 CONFIG_SYS_FLASH_BASE when booting from flash.
2351 - CONFIG_SYS_MONITOR_LEN:
2352 Size of memory reserved for monitor code, used to
2353 determine _at_compile_time_ (!) if the environment is
2354 embedded within the U-Boot image, or in a separate
2357 - CONFIG_SYS_MALLOC_LEN:
2358 Size of DRAM reserved for malloc() use.
2360 - CONFIG_SYS_BOOTM_LEN:
2361 Normally compressed uImages are limited to an
2362 uncompressed size of 8 MBytes. If this is not enough,
2363 you can define CONFIG_SYS_BOOTM_LEN in your board config file
2364 to adjust this setting to your needs.
2366 - CONFIG_SYS_BOOTMAPSZ:
2367 Maximum size of memory mapped by the startup code of
2368 the Linux kernel; all data that must be processed by
2369 the Linux kernel (bd_info, boot arguments, FDT blob if
2370 used) must be put below this limit, unless "bootm_low"
2371 enviroment variable is defined and non-zero. In such case
2372 all data for the Linux kernel must be between "bootm_low"
2373 and "bootm_low" + CONFIG_SYS_BOOTMAPSZ. The environment
2374 variable "bootm_mapsize" will override the value of
2375 CONFIG_SYS_BOOTMAPSZ. If CONFIG_SYS_BOOTMAPSZ is undefined,
2376 then the value in "bootm_size" will be used instead.
2378 - CONFIG_SYS_BOOT_RAMDISK_HIGH:
2379 Enable initrd_high functionality. If defined then the
2380 initrd_high feature is enabled and the bootm ramdisk subcommand
2383 - CONFIG_SYS_BOOT_GET_CMDLINE:
2384 Enables allocating and saving kernel cmdline in space between
2385 "bootm_low" and "bootm_low" + BOOTMAPSZ.
2387 - CONFIG_SYS_BOOT_GET_KBD:
2388 Enables allocating and saving a kernel copy of the bd_info in
2389 space between "bootm_low" and "bootm_low" + BOOTMAPSZ.
2391 - CONFIG_SYS_MAX_FLASH_BANKS:
2392 Max number of Flash memory banks
2394 - CONFIG_SYS_MAX_FLASH_SECT:
2395 Max number of sectors on a Flash chip
2397 - CONFIG_SYS_FLASH_ERASE_TOUT:
2398 Timeout for Flash erase operations (in ms)
2400 - CONFIG_SYS_FLASH_WRITE_TOUT:
2401 Timeout for Flash write operations (in ms)
2403 - CONFIG_SYS_FLASH_LOCK_TOUT
2404 Timeout for Flash set sector lock bit operation (in ms)
2406 - CONFIG_SYS_FLASH_UNLOCK_TOUT
2407 Timeout for Flash clear lock bits operation (in ms)
2409 - CONFIG_SYS_FLASH_PROTECTION
2410 If defined, hardware flash sectors protection is used
2411 instead of U-Boot software protection.
2413 - CONFIG_SYS_DIRECT_FLASH_TFTP:
2415 Enable TFTP transfers directly to flash memory;
2416 without this option such a download has to be
2417 performed in two steps: (1) download to RAM, and (2)
2418 copy from RAM to flash.
2420 The two-step approach is usually more reliable, since
2421 you can check if the download worked before you erase
2422 the flash, but in some situations (when system RAM is
2423 too limited to allow for a temporary copy of the
2424 downloaded image) this option may be very useful.
2426 - CONFIG_SYS_FLASH_CFI:
2427 Define if the flash driver uses extra elements in the
2428 common flash structure for storing flash geometry.
2430 - CONFIG_FLASH_CFI_DRIVER
2431 This option also enables the building of the cfi_flash driver
2432 in the drivers directory
2434 - CONFIG_FLASH_CFI_MTD
2435 This option enables the building of the cfi_mtd driver
2436 in the drivers directory. The driver exports CFI flash
2439 - CONFIG_SYS_FLASH_USE_BUFFER_WRITE
2440 Use buffered writes to flash.
2442 - CONFIG_FLASH_SPANSION_S29WS_N
2443 s29ws-n MirrorBit flash has non-standard addresses for buffered
2446 - CONFIG_SYS_FLASH_QUIET_TEST
2447 If this option is defined, the common CFI flash doesn't
2448 print it's warning upon not recognized FLASH banks. This
2449 is useful, if some of the configured banks are only
2450 optionally available.
2452 - CONFIG_FLASH_SHOW_PROGRESS
2453 If defined (must be an integer), print out countdown
2454 digits and dots. Recommended value: 45 (9..1) for 80
2455 column displays, 15 (3..1) for 40 column displays.
2457 - CONFIG_SYS_RX_ETH_BUFFER:
2458 Defines the number of Ethernet receive buffers. On some
2459 Ethernet controllers it is recommended to set this value
2460 to 8 or even higher (EEPRO100 or 405 EMAC), since all
2461 buffers can be full shortly after enabling the interface
2462 on high Ethernet traffic.
2463 Defaults to 4 if not defined.
2465 - CONFIG_ENV_MAX_ENTRIES
2467 Maximum number of entries in the hash table that is used
2468 internally to store the environment settings. The default
2469 setting is supposed to be generous and should work in most
2470 cases. This setting can be used to tune behaviour; see
2471 lib/hashtable.c for details.
2473 The following definitions that deal with the placement and management
2474 of environment data (variable area); in general, we support the
2475 following configurations:
2477 - CONFIG_ENV_IS_IN_FLASH:
2479 Define this if the environment is in flash memory.
2481 a) The environment occupies one whole flash sector, which is
2482 "embedded" in the text segment with the U-Boot code. This
2483 happens usually with "bottom boot sector" or "top boot
2484 sector" type flash chips, which have several smaller
2485 sectors at the start or the end. For instance, such a
2486 layout can have sector sizes of 8, 2x4, 16, Nx32 kB. In
2487 such a case you would place the environment in one of the
2488 4 kB sectors - with U-Boot code before and after it. With
2489 "top boot sector" type flash chips, you would put the
2490 environment in one of the last sectors, leaving a gap
2491 between U-Boot and the environment.
2493 - CONFIG_ENV_OFFSET:
2495 Offset of environment data (variable area) to the
2496 beginning of flash memory; for instance, with bottom boot
2497 type flash chips the second sector can be used: the offset
2498 for this sector is given here.
2500 CONFIG_ENV_OFFSET is used relative to CONFIG_SYS_FLASH_BASE.
2504 This is just another way to specify the start address of
2505 the flash sector containing the environment (instead of
2508 - CONFIG_ENV_SECT_SIZE:
2510 Size of the sector containing the environment.
2513 b) Sometimes flash chips have few, equal sized, BIG sectors.
2514 In such a case you don't want to spend a whole sector for
2519 If you use this in combination with CONFIG_ENV_IS_IN_FLASH
2520 and CONFIG_ENV_SECT_SIZE, you can specify to use only a part
2521 of this flash sector for the environment. This saves
2522 memory for the RAM copy of the environment.
2524 It may also save flash memory if you decide to use this
2525 when your environment is "embedded" within U-Boot code,
2526 since then the remainder of the flash sector could be used
2527 for U-Boot code. It should be pointed out that this is
2528 STRONGLY DISCOURAGED from a robustness point of view:
2529 updating the environment in flash makes it always
2530 necessary to erase the WHOLE sector. If something goes
2531 wrong before the contents has been restored from a copy in
2532 RAM, your target system will be dead.
2534 - CONFIG_ENV_ADDR_REDUND
2535 CONFIG_ENV_SIZE_REDUND
2537 These settings describe a second storage area used to hold
2538 a redundant copy of the environment data, so that there is
2539 a valid backup copy in case there is a power failure during
2540 a "saveenv" operation.
2542 BE CAREFUL! Any changes to the flash layout, and some changes to the
2543 source code will make it necessary to adapt <board>/u-boot.lds*
2547 - CONFIG_ENV_IS_IN_NVRAM:
2549 Define this if you have some non-volatile memory device
2550 (NVRAM, battery buffered SRAM) which you want to use for the
2556 These two #defines are used to determine the memory area you
2557 want to use for environment. It is assumed that this memory
2558 can just be read and written to, without any special
2561 BE CAREFUL! The first access to the environment happens quite early
2562 in U-Boot initalization (when we try to get the setting of for the
2563 console baudrate). You *MUST* have mapped your NVRAM area then, or
2566 Please note that even with NVRAM we still use a copy of the
2567 environment in RAM: we could work on NVRAM directly, but we want to
2568 keep settings there always unmodified except somebody uses "saveenv"
2569 to save the current settings.
2572 - CONFIG_ENV_IS_IN_EEPROM:
2574 Use this if you have an EEPROM or similar serial access
2575 device and a driver for it.
2577 - CONFIG_ENV_OFFSET:
2580 These two #defines specify the offset and size of the
2581 environment area within the total memory of your EEPROM.
2583 - CONFIG_SYS_I2C_EEPROM_ADDR:
2584 If defined, specified the chip address of the EEPROM device.
2585 The default address is zero.
2587 - CONFIG_SYS_EEPROM_PAGE_WRITE_BITS:
2588 If defined, the number of bits used to address bytes in a
2589 single page in the EEPROM device. A 64 byte page, for example
2590 would require six bits.
2592 - CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS:
2593 If defined, the number of milliseconds to delay between
2594 page writes. The default is zero milliseconds.
2596 - CONFIG_SYS_I2C_EEPROM_ADDR_LEN:
2597 The length in bytes of the EEPROM memory array address. Note
2598 that this is NOT the chip address length!
2600 - CONFIG_SYS_I2C_EEPROM_ADDR_OVERFLOW:
2601 EEPROM chips that implement "address overflow" are ones
2602 like Catalyst 24WC04/08/16 which has 9/10/11 bits of
2603 address and the extra bits end up in the "chip address" bit
2604 slots. This makes a 24WC08 (1Kbyte) chip look like four 256
2607 Note that we consider the length of the address field to
2608 still be one byte because the extra address bits are hidden
2609 in the chip address.
2611 - CONFIG_SYS_EEPROM_SIZE:
2612 The size in bytes of the EEPROM device.
2614 - CONFIG_ENV_EEPROM_IS_ON_I2C
2615 define this, if you have I2C and SPI activated, and your
2616 EEPROM, which holds the environment, is on the I2C bus.
2618 - CONFIG_I2C_ENV_EEPROM_BUS
2619 if you have an Environment on an EEPROM reached over
2620 I2C muxes, you can define here, how to reach this
2621 EEPROM. For example:
2623 #define CONFIG_I2C_ENV_EEPROM_BUS "pca9547:70:d\0"
2625 EEPROM which holds the environment, is reached over
2626 a pca9547 i2c mux with address 0x70, channel 3.
2628 - CONFIG_ENV_IS_IN_DATAFLASH:
2630 Define this if you have a DataFlash memory device which you
2631 want to use for the environment.
2633 - CONFIG_ENV_OFFSET:
2637 These three #defines specify the offset and size of the
2638 environment area within the total memory of your DataFlash placed
2639 at the specified address.
2641 - CONFIG_ENV_IS_IN_NAND:
2643 Define this if you have a NAND device which you want to use
2644 for the environment.
2646 - CONFIG_ENV_OFFSET:
2649 These two #defines specify the offset and size of the environment
2650 area within the first NAND device. CONFIG_ENV_OFFSET must be
2651 aligned to an erase block boundary.
2653 - CONFIG_ENV_OFFSET_REDUND (optional):
2655 This setting describes a second storage area of CONFIG_ENV_SIZE
2656 size used to hold a redundant copy of the environment data, so
2657 that there is a valid backup copy in case there is a power failure
2658 during a "saveenv" operation. CONFIG_ENV_OFFSET_RENDUND must be
2659 aligned to an erase block boundary.
2661 - CONFIG_ENV_RANGE (optional):
2663 Specifies the length of the region in which the environment
2664 can be written. This should be a multiple of the NAND device's
2665 block size. Specifying a range with more erase blocks than
2666 are needed to hold CONFIG_ENV_SIZE allows bad blocks within
2667 the range to be avoided.
2669 - CONFIG_ENV_OFFSET_OOB (optional):
2671 Enables support for dynamically retrieving the offset of the
2672 environment from block zero's out-of-band data. The
2673 "nand env.oob" command can be used to record this offset.
2674 Currently, CONFIG_ENV_OFFSET_REDUND is not supported when
2675 using CONFIG_ENV_OFFSET_OOB.
2677 - CONFIG_NAND_ENV_DST
2679 Defines address in RAM to which the nand_spl code should copy the
2680 environment. If redundant environment is used, it will be copied to
2681 CONFIG_NAND_ENV_DST + CONFIG_ENV_SIZE.
2683 - CONFIG_SYS_SPI_INIT_OFFSET
2685 Defines offset to the initial SPI buffer area in DPRAM. The
2686 area is used at an early stage (ROM part) if the environment
2687 is configured to reside in the SPI EEPROM: We need a 520 byte
2688 scratch DPRAM area. It is used between the two initialization
2689 calls (spi_init_f() and spi_init_r()). A value of 0xB00 seems
2690 to be a good choice since it makes it far enough from the
2691 start of the data area as well as from the stack pointer.
2693 Please note that the environment is read-only until the monitor
2694 has been relocated to RAM and a RAM copy of the environment has been
2695 created; also, when using EEPROM you will have to use getenv_f()
2696 until then to read environment variables.
2698 The environment is protected by a CRC32 checksum. Before the monitor
2699 is relocated into RAM, as a result of a bad CRC you will be working
2700 with the compiled-in default environment - *silently*!!! [This is
2701 necessary, because the first environment variable we need is the
2702 "baudrate" setting for the console - if we have a bad CRC, we don't
2703 have any device yet where we could complain.]
2705 Note: once the monitor has been relocated, then it will complain if
2706 the default environment is used; a new CRC is computed as soon as you
2707 use the "saveenv" command to store a valid environment.
2709 - CONFIG_SYS_FAULT_ECHO_LINK_DOWN:
2710 Echo the inverted Ethernet link state to the fault LED.
2712 Note: If this option is active, then CONFIG_SYS_FAULT_MII_ADDR
2713 also needs to be defined.
2715 - CONFIG_SYS_FAULT_MII_ADDR:
2716 MII address of the PHY to check for the Ethernet link state.
2718 - CONFIG_NS16550_MIN_FUNCTIONS:
2719 Define this if you desire to only have use of the NS16550_init
2720 and NS16550_putc functions for the serial driver located at
2721 drivers/serial/ns16550.c. This option is useful for saving
2722 space for already greatly restricted images, including but not
2723 limited to NAND_SPL configurations.
2725 Low Level (hardware related) configuration options:
2726 ---------------------------------------------------
2728 - CONFIG_SYS_CACHELINE_SIZE:
2729 Cache Line Size of the CPU.
2731 - CONFIG_SYS_DEFAULT_IMMR:
2732 Default address of the IMMR after system reset.
2734 Needed on some 8260 systems (MPC8260ADS, PQ2FADS-ZU,
2735 and RPXsuper) to be able to adjust the position of
2736 the IMMR register after a reset.
2738 - Floppy Disk Support:
2739 CONFIG_SYS_FDC_DRIVE_NUMBER
2741 the default drive number (default value 0)
2743 CONFIG_SYS_ISA_IO_STRIDE
2745 defines the spacing between FDC chipset registers
2748 CONFIG_SYS_ISA_IO_OFFSET
2750 defines the offset of register from address. It
2751 depends on which part of the data bus is connected to
2752 the FDC chipset. (default value 0)
2754 If CONFIG_SYS_ISA_IO_STRIDE CONFIG_SYS_ISA_IO_OFFSET and
2755 CONFIG_SYS_FDC_DRIVE_NUMBER are undefined, they take their
2758 if CONFIG_SYS_FDC_HW_INIT is defined, then the function
2759 fdc_hw_init() is called at the beginning of the FDC
2760 setup. fdc_hw_init() must be provided by the board
2761 source code. It is used to make hardware dependant
2764 - CONFIG_SYS_IMMR: Physical address of the Internal Memory.
2765 DO NOT CHANGE unless you know exactly what you're
2766 doing! (11-4) [MPC8xx/82xx systems only]
2768 - CONFIG_SYS_INIT_RAM_ADDR:
2770 Start address of memory area that can be used for
2771 initial data and stack; please note that this must be
2772 writable memory that is working WITHOUT special
2773 initialization, i. e. you CANNOT use normal RAM which
2774 will become available only after programming the
2775 memory controller and running certain initialization
2778 U-Boot uses the following memory types:
2779 - MPC8xx and MPC8260: IMMR (internal memory of the CPU)
2780 - MPC824X: data cache
2781 - PPC4xx: data cache
2783 - CONFIG_SYS_GBL_DATA_OFFSET:
2785 Offset of the initial data structure in the memory
2786 area defined by CONFIG_SYS_INIT_RAM_ADDR. Usually
2787 CONFIG_SYS_GBL_DATA_OFFSET is chosen such that the initial
2788 data is located at the end of the available space
2789 (sometimes written as (CONFIG_SYS_INIT_RAM_SIZE -
2790 CONFIG_SYS_INIT_DATA_SIZE), and the initial stack is just
2791 below that area (growing from (CONFIG_SYS_INIT_RAM_ADDR +
2792 CONFIG_SYS_GBL_DATA_OFFSET) downward.
2795 On the MPC824X (or other systems that use the data
2796 cache for initial memory) the address chosen for
2797 CONFIG_SYS_INIT_RAM_ADDR is basically arbitrary - it must
2798 point to an otherwise UNUSED address space between
2799 the top of RAM and the start of the PCI space.
2801 - CONFIG_SYS_SIUMCR: SIU Module Configuration (11-6)
2803 - CONFIG_SYS_SYPCR: System Protection Control (11-9)
2805 - CONFIG_SYS_TBSCR: Time Base Status and Control (11-26)
2807 - CONFIG_SYS_PISCR: Periodic Interrupt Status and Control (11-31)
2809 - CONFIG_SYS_PLPRCR: PLL, Low-Power, and Reset Control Register (15-30)
2811 - CONFIG_SYS_SCCR: System Clock and reset Control Register (15-27)
2813 - CONFIG_SYS_OR_TIMING_SDRAM:
2816 - CONFIG_SYS_MAMR_PTA:
2817 periodic timer for refresh
2819 - CONFIG_SYS_DER: Debug Event Register (37-47)
2821 - FLASH_BASE0_PRELIM, FLASH_BASE1_PRELIM, CONFIG_SYS_REMAP_OR_AM,
2822 CONFIG_SYS_PRELIM_OR_AM, CONFIG_SYS_OR_TIMING_FLASH, CONFIG_SYS_OR0_REMAP,
2823 CONFIG_SYS_OR0_PRELIM, CONFIG_SYS_BR0_PRELIM, CONFIG_SYS_OR1_REMAP, CONFIG_SYS_OR1_PRELIM,
2824 CONFIG_SYS_BR1_PRELIM:
2825 Memory Controller Definitions: BR0/1 and OR0/1 (FLASH)
2827 - SDRAM_BASE2_PRELIM, SDRAM_BASE3_PRELIM, SDRAM_MAX_SIZE,
2828 CONFIG_SYS_OR_TIMING_SDRAM, CONFIG_SYS_OR2_PRELIM, CONFIG_SYS_BR2_PRELIM,
2829 CONFIG_SYS_OR3_PRELIM, CONFIG_SYS_BR3_PRELIM:
2830 Memory Controller Definitions: BR2/3 and OR2/3 (SDRAM)
2832 - CONFIG_SYS_MAMR_PTA, CONFIG_SYS_MPTPR_2BK_4K, CONFIG_SYS_MPTPR_1BK_4K, CONFIG_SYS_MPTPR_2BK_8K,
2833 CONFIG_SYS_MPTPR_1BK_8K, CONFIG_SYS_MAMR_8COL, CONFIG_SYS_MAMR_9COL:
2834 Machine Mode Register and Memory Periodic Timer
2835 Prescaler definitions (SDRAM timing)
2837 - CONFIG_SYS_I2C_UCODE_PATCH, CONFIG_SYS_I2C_DPMEM_OFFSET [0x1FC0]:
2838 enable I2C microcode relocation patch (MPC8xx);
2839 define relocation offset in DPRAM [DSP2]
2841 - CONFIG_SYS_SMC_UCODE_PATCH, CONFIG_SYS_SMC_DPMEM_OFFSET [0x1FC0]:
2842 enable SMC microcode relocation patch (MPC8xx);
2843 define relocation offset in DPRAM [SMC1]
2845 - CONFIG_SYS_SPI_UCODE_PATCH, CONFIG_SYS_SPI_DPMEM_OFFSET [0x1FC0]:
2846 enable SPI microcode relocation patch (MPC8xx);
2847 define relocation offset in DPRAM [SCC4]
2849 - CONFIG_SYS_USE_OSCCLK:
2850 Use OSCM clock mode on MBX8xx board. Be careful,
2851 wrong setting might damage your board. Read
2852 doc/README.MBX before setting this variable!
2854 - CONFIG_SYS_CPM_POST_WORD_ADDR: (MPC8xx, MPC8260 only)
2855 Offset of the bootmode word in DPRAM used by post
2856 (Power On Self Tests). This definition overrides
2857 #define'd default value in commproc.h resp.
2860 - CONFIG_SYS_PCI_SLV_MEM_LOCAL, CONFIG_SYS_PCI_SLV_MEM_BUS, CONFIG_SYS_PICMR0_MASK_ATTRIB,
2861 CONFIG_SYS_PCI_MSTR0_LOCAL, CONFIG_SYS_PCIMSK0_MASK, CONFIG_SYS_PCI_MSTR1_LOCAL,
2862 CONFIG_SYS_PCIMSK1_MASK, CONFIG_SYS_PCI_MSTR_MEM_LOCAL, CONFIG_SYS_PCI_MSTR_MEM_BUS,
2863 CONFIG_SYS_CPU_PCI_MEM_START, CONFIG_SYS_PCI_MSTR_MEM_SIZE, CONFIG_SYS_POCMR0_MASK_ATTRIB,
2864 CONFIG_SYS_PCI_MSTR_MEMIO_LOCAL, CONFIG_SYS_PCI_MSTR_MEMIO_BUS, CPU_PCI_MEMIO_START,
2865 CONFIG_SYS_PCI_MSTR_MEMIO_SIZE, CONFIG_SYS_POCMR1_MASK_ATTRIB, CONFIG_SYS_PCI_MSTR_IO_LOCAL,
2866 CONFIG_SYS_PCI_MSTR_IO_BUS, CONFIG_SYS_CPU_PCI_IO_START, CONFIG_SYS_PCI_MSTR_IO_SIZE,
2867 CONFIG_SYS_POCMR2_MASK_ATTRIB: (MPC826x only)
2868 Overrides the default PCI memory map in arch/powerpc/cpu/mpc8260/pci.c if set.
2870 - CONFIG_PCI_DISABLE_PCIE:
2871 Disable PCI-Express on systems where it is supported but not
2875 Chip has SRIO or not
2878 Board has SRIO 1 port available
2881 Board has SRIO 2 port available
2883 - CONFIG_SYS_SRIOn_MEM_VIRT:
2884 Virtual Address of SRIO port 'n' memory region
2886 - CONFIG_SYS_SRIOn_MEM_PHYS:
2887 Physical Address of SRIO port 'n' memory region
2889 - CONFIG_SYS_SRIOn_MEM_SIZE:
2890 Size of SRIO port 'n' memory region
2893 Get DDR timing information from an I2C EEPROM. Common
2894 with pluggable memory modules such as SODIMMs
2897 I2C address of the SPD EEPROM
2899 - CONFIG_SYS_SPD_BUS_NUM
2900 If SPD EEPROM is on an I2C bus other than the first
2901 one, specify here. Note that the value must resolve
2902 to something your driver can deal with.
2904 - CONFIG_SYS_83XX_DDR_USES_CS0
2905 Only for 83xx systems. If specified, then DDR should
2906 be configured using CS0 and CS1 instead of CS2 and CS3.
2908 - CONFIG_ETHER_ON_FEC[12]
2909 Define to enable FEC[12] on a 8xx series processor.
2911 - CONFIG_FEC[12]_PHY
2912 Define to the hardcoded PHY address which corresponds
2913 to the given FEC; i. e.
2914 #define CONFIG_FEC1_PHY 4
2915 means that the PHY with address 4 is connected to FEC1
2917 When set to -1, means to probe for first available.
2919 - CONFIG_FEC[12]_PHY_NORXERR
2920 The PHY does not have a RXERR line (RMII only).
2921 (so program the FEC to ignore it).
2924 Enable RMII mode for all FECs.
2925 Note that this is a global option, we can't
2926 have one FEC in standard MII mode and another in RMII mode.
2928 - CONFIG_CRC32_VERIFY
2929 Add a verify option to the crc32 command.
2932 => crc32 -v <address> <count> <crc32>
2934 Where address/count indicate a memory area
2935 and crc32 is the correct crc32 which the
2939 Add the "loopw" memory command. This only takes effect if
2940 the memory commands are activated globally (CONFIG_CMD_MEM).
2943 Add the "mdc" and "mwc" memory commands. These are cyclic
2948 This command will print 4 bytes (10,11,12,13) each 500 ms.
2950 => mwc.l 100 12345678 10
2951 This command will write 12345678 to address 100 all 10 ms.
2953 This only takes effect if the memory commands are activated
2954 globally (CONFIG_CMD_MEM).
2956 - CONFIG_SKIP_LOWLEVEL_INIT
2957 [ARM only] If this variable is defined, then certain
2958 low level initializations (like setting up the memory
2959 controller) are omitted and/or U-Boot does not
2960 relocate itself into RAM.
2962 Normally this variable MUST NOT be defined. The only
2963 exception is when U-Boot is loaded (to RAM) by some
2964 other boot loader or by a debugger which performs
2965 these initializations itself.
2968 Modifies the behaviour of start.S when compiling a loader
2969 that is executed before the actual U-Boot. E.g. when
2970 compiling a NAND SPL.
2972 - CONFIG_USE_ARCH_MEMCPY
2973 CONFIG_USE_ARCH_MEMSET
2974 If these options are used a optimized version of memcpy/memset will
2975 be used if available. These functions may be faster under some
2976 conditions but may increase the binary size.
2978 Building the Software:
2979 ======================
2981 Building U-Boot has been tested in several native build environments
2982 and in many different cross environments. Of course we cannot support
2983 all possibly existing versions of cross development tools in all
2984 (potentially obsolete) versions. In case of tool chain problems we
2985 recommend to use the ELDK (see http://www.denx.de/wiki/DULG/ELDK)
2986 which is extensively used to build and test U-Boot.
2988 If you are not using a native environment, it is assumed that you
2989 have GNU cross compiling tools available in your path. In this case,
2990 you must set the environment variable CROSS_COMPILE in your shell.
2991 Note that no changes to the Makefile or any other source files are
2992 necessary. For example using the ELDK on a 4xx CPU, please enter:
2994 $ CROSS_COMPILE=ppc_4xx-
2995 $ export CROSS_COMPILE
2997 Note: If you wish to generate Windows versions of the utilities in
2998 the tools directory you can use the MinGW toolchain
2999 (http://www.mingw.org). Set your HOST tools to the MinGW
3000 toolchain and execute 'make tools'. For example:
3002 $ make HOSTCC=i586-mingw32msvc-gcc HOSTSTRIP=i586-mingw32msvc-strip tools
3004 Binaries such as tools/mkimage.exe will be created which can
3005 be executed on computers running Windows.
3007 U-Boot is intended to be simple to build. After installing the
3008 sources you must configure U-Boot for one specific board type. This
3013 where "NAME_config" is the name of one of the existing configu-
3014 rations; see the main Makefile for supported names.
3016 Note: for some board special configuration names may exist; check if
3017 additional information is available from the board vendor; for
3018 instance, the TQM823L systems are available without (standard)
3019 or with LCD support. You can select such additional "features"
3020 when choosing the configuration, i. e.
3023 - will configure for a plain TQM823L, i. e. no LCD support
3025 make TQM823L_LCD_config
3026 - will configure for a TQM823L with U-Boot console on LCD
3031 Finally, type "make all", and you should get some working U-Boot
3032 images ready for download to / installation on your system:
3034 - "u-boot.bin" is a raw binary image
3035 - "u-boot" is an image in ELF binary format
3036 - "u-boot.srec" is in Motorola S-Record format
3038 By default the build is performed locally and the objects are saved
3039 in the source directory. One of the two methods can be used to change
3040 this behavior and build U-Boot to some external directory:
3042 1. Add O= to the make command line invocations:
3044 make O=/tmp/build distclean
3045 make O=/tmp/build NAME_config
3046 make O=/tmp/build all
3048 2. Set environment variable BUILD_DIR to point to the desired location:
3050 export BUILD_DIR=/tmp/build
3055 Note that the command line "O=" setting overrides the BUILD_DIR environment
3059 Please be aware that the Makefiles assume you are using GNU make, so
3060 for instance on NetBSD you might need to use "gmake" instead of
3064 If the system board that you have is not listed, then you will need
3065 to port U-Boot to your hardware platform. To do this, follow these
3068 1. Add a new configuration option for your board to the toplevel
3069 "Makefile" and to the "MAKEALL" script, using the existing
3070 entries as examples. Note that here and at many other places
3071 boards and other names are listed in alphabetical sort order. Please
3073 2. Create a new directory to hold your board specific code. Add any
3074 files you need. In your board directory, you will need at least
3075 the "Makefile", a "<board>.c", "flash.c" and "u-boot.lds".
3076 3. Create a new configuration file "include/configs/<board>.h" for
3078 3. If you're porting U-Boot to a new CPU, then also create a new
3079 directory to hold your CPU specific code. Add any files you need.
3080 4. Run "make <board>_config" with your new name.
3081 5. Type "make", and you should get a working "u-boot.srec" file
3082 to be installed on your target system.
3083 6. Debug and solve any problems that might arise.
3084 [Of course, this last step is much harder than it sounds.]
3087 Testing of U-Boot Modifications, Ports to New Hardware, etc.:
3088 ==============================================================
3090 If you have modified U-Boot sources (for instance added a new board
3091 or support for new devices, a new CPU, etc.) you are expected to
3092 provide feedback to the other developers. The feedback normally takes
3093 the form of a "patch", i. e. a context diff against a certain (latest
3094 official or latest in the git repository) version of U-Boot sources.
3096 But before you submit such a patch, please verify that your modifi-
3097 cation did not break existing code. At least make sure that *ALL* of
3098 the supported boards compile WITHOUT ANY compiler warnings. To do so,
3099 just run the "MAKEALL" script, which will configure and build U-Boot
3100 for ALL supported system. Be warned, this will take a while. You can
3101 select which (cross) compiler to use by passing a `CROSS_COMPILE'
3102 environment variable to the script, i. e. to use the ELDK cross tools
3105 CROSS_COMPILE=ppc_8xx- MAKEALL
3107 or to build on a native PowerPC system you can type
3109 CROSS_COMPILE=' ' MAKEALL
3111 When using the MAKEALL script, the default behaviour is to build
3112 U-Boot in the source directory. This location can be changed by
3113 setting the BUILD_DIR environment variable. Also, for each target
3114 built, the MAKEALL script saves two log files (<target>.ERR and
3115 <target>.MAKEALL) in the <source dir>/LOG directory. This default
3116 location can be changed by setting the MAKEALL_LOGDIR environment
3117 variable. For example:
3119 export BUILD_DIR=/tmp/build
3120 export MAKEALL_LOGDIR=/tmp/log
3121 CROSS_COMPILE=ppc_8xx- MAKEALL
3123 With the above settings build objects are saved in the /tmp/build,
3124 log files are saved in the /tmp/log and the source tree remains clean
3125 during the whole build process.
3128 See also "U-Boot Porting Guide" below.
3131 Monitor Commands - Overview:
3132 ============================
3134 go - start application at address 'addr'
3135 run - run commands in an environment variable
3136 bootm - boot application image from memory
3137 bootp - boot image via network using BootP/TFTP protocol
3138 tftpboot- boot image via network using TFTP protocol
3139 and env variables "ipaddr" and "serverip"
3140 (and eventually "gatewayip")
3141 rarpboot- boot image via network using RARP/TFTP protocol
3142 diskboot- boot from IDE devicebootd - boot default, i.e., run 'bootcmd'
3143 loads - load S-Record file over serial line
3144 loadb - load binary file over serial line (kermit mode)
3146 mm - memory modify (auto-incrementing)
3147 nm - memory modify (constant address)
3148 mw - memory write (fill)
3150 cmp - memory compare
3151 crc32 - checksum calculation
3152 i2c - I2C sub-system
3153 sspi - SPI utility commands
3154 base - print or set address offset
3155 printenv- print environment variables
3156 setenv - set environment variables
3157 saveenv - save environment variables to persistent storage
3158 protect - enable or disable FLASH write protection
3159 erase - erase FLASH memory
3160 flinfo - print FLASH memory information
3161 bdinfo - print Board Info structure
3162 iminfo - print header information for application image
3163 coninfo - print console devices and informations
3164 ide - IDE sub-system
3165 loop - infinite loop on address range
3166 loopw - infinite write loop on address range
3167 mtest - simple RAM test
3168 icache - enable or disable instruction cache
3169 dcache - enable or disable data cache
3170 reset - Perform RESET of the CPU
3171 echo - echo args to console
3172 version - print monitor version
3173 help - print online help
3174 ? - alias for 'help'
3177 Monitor Commands - Detailed Description:
3178 ========================================
3182 For now: just type "help <command>".
3185 Environment Variables:
3186 ======================
3188 U-Boot supports user configuration using Environment Variables which
3189 can be made persistent by saving to Flash memory.
3191 Environment Variables are set using "setenv", printed using
3192 "printenv", and saved to Flash using "saveenv". Using "setenv"
3193 without a value can be used to delete a variable from the
3194 environment. As long as you don't save the environment you are
3195 working with an in-memory copy. In case the Flash area containing the
3196 environment is erased by accident, a default environment is provided.
3198 Some configuration options can be set using Environment Variables.
3200 List of environment variables (most likely not complete):
3202 baudrate - see CONFIG_BAUDRATE
3204 bootdelay - see CONFIG_BOOTDELAY
3206 bootcmd - see CONFIG_BOOTCOMMAND
3208 bootargs - Boot arguments when booting an RTOS image
3210 bootfile - Name of the image to load with TFTP
3212 bootm_low - Memory range available for image processing in the bootm
3213 command can be restricted. This variable is given as
3214 a hexadecimal number and defines lowest address allowed
3215 for use by the bootm command. See also "bootm_size"
3216 environment variable. Address defined by "bootm_low" is
3217 also the base of the initial memory mapping for the Linux
3218 kernel -- see the description of CONFIG_SYS_BOOTMAPSZ and
3221 bootm_mapsize - Size of the initial memory mapping for the Linux kernel.
3222 This variable is given as a hexadecimal number and it
3223 defines the size of the memory region starting at base
3224 address bootm_low that is accessible by the Linux kernel
3225 during early boot. If unset, CONFIG_SYS_BOOTMAPSZ is used
3226 as the default value if it is defined, and bootm_size is
3229 bootm_size - Memory range available for image processing in the bootm
3230 command can be restricted. This variable is given as
3231 a hexadecimal number and defines the size of the region
3232 allowed for use by the bootm command. See also "bootm_low"
3233 environment variable.
3235 updatefile - Location of the software update file on a TFTP server, used
3236 by the automatic software update feature. Please refer to
3237 documentation in doc/README.update for more details.
3239 autoload - if set to "no" (any string beginning with 'n'),
3240 "bootp" will just load perform a lookup of the
3241 configuration from the BOOTP server, but not try to
3242 load any image using TFTP
3244 autostart - if set to "yes", an image loaded using the "bootp",
3245 "rarpboot", "tftpboot" or "diskboot" commands will
3246 be automatically started (by internally calling
3249 If set to "no", a standalone image passed to the
3250 "bootm" command will be copied to the load address
3251 (and eventually uncompressed), but NOT be started.
3252 This can be used to load and uncompress arbitrary
3255 i2cfast - (PPC405GP|PPC405EP only)
3256 if set to 'y' configures Linux I2C driver for fast
3257 mode (400kHZ). This environment variable is used in
3258 initialization code. So, for changes to be effective
3259 it must be saved and board must be reset.
3261 initrd_high - restrict positioning of initrd images:
3262 If this variable is not set, initrd images will be
3263 copied to the highest possible address in RAM; this
3264 is usually what you want since it allows for
3265 maximum initrd size. If for some reason you want to
3266 make sure that the initrd image is loaded below the
3267 CONFIG_SYS_BOOTMAPSZ limit, you can set this environment
3268 variable to a value of "no" or "off" or "0".
3269 Alternatively, you can set it to a maximum upper
3270 address to use (U-Boot will still check that it
3271 does not overwrite the U-Boot stack and data).
3273 For instance, when you have a system with 16 MB
3274 RAM, and want to reserve 4 MB from use by Linux,
3275 you can do this by adding "mem=12M" to the value of
3276 the "bootargs" variable. However, now you must make
3277 sure that the initrd image is placed in the first
3278 12 MB as well - this can be done with
3280 setenv initrd_high 00c00000
3282 If you set initrd_high to 0xFFFFFFFF, this is an
3283 indication to U-Boot that all addresses are legal
3284 for the Linux kernel, including addresses in flash
3285 memory. In this case U-Boot will NOT COPY the
3286 ramdisk at all. This may be useful to reduce the
3287 boot time on your system, but requires that this
3288 feature is supported by your Linux kernel.
3290 ipaddr - IP address; needed for tftpboot command
3292 loadaddr - Default load address for commands like "bootp",
3293 "rarpboot", "tftpboot", "loadb" or "diskboot"
3295 loads_echo - see CONFIG_LOADS_ECHO
3297 serverip - TFTP server IP address; needed for tftpboot command
3299 bootretry - see CONFIG_BOOT_RETRY_TIME
3301 bootdelaykey - see CONFIG_AUTOBOOT_DELAY_STR
3303 bootstopkey - see CONFIG_AUTOBOOT_STOP_STR
3305 ethprime - When CONFIG_NET_MULTI is enabled controls which
3306 interface is used first.
3308 ethact - When CONFIG_NET_MULTI is enabled controls which
3309 interface is currently active. For example you
3310 can do the following
3312 => setenv ethact FEC
3313 => ping 192.168.0.1 # traffic sent on FEC
3314 => setenv ethact SCC
3315 => ping 10.0.0.1 # traffic sent on SCC
3317 ethrotate - When set to "no" U-Boot does not go through all
3318 available network interfaces.
3319 It just stays at the currently selected interface.
3321 netretry - When set to "no" each network operation will
3322 either succeed or fail without retrying.
3323 When set to "once" the network operation will
3324 fail when all the available network interfaces
3325 are tried once without success.
3326 Useful on scripts which control the retry operation
3329 npe_ucode - set load address for the NPE microcode
3331 tftpsrcport - If this is set, the value is used for TFTP's
3334 tftpdstport - If this is set, the value is used for TFTP's UDP
3335 destination port instead of the Well Know Port 69.
3337 tftpblocksize - Block size to use for TFTP transfers; if not set,
3338 we use the TFTP server's default block size
3340 tftptimeout - Retransmission timeout for TFTP packets (in milli-
3341 seconds, minimum value is 1000 = 1 second). Defines
3342 when a packet is considered to be lost so it has to
3343 be retransmitted. The default is 5000 = 5 seconds.
3344 Lowering this value may make downloads succeed
3345 faster in networks with high packet loss rates or
3346 with unreliable TFTP servers.
3348 vlan - When set to a value < 4095 the traffic over
3349 Ethernet is encapsulated/received over 802.1q
3352 The following environment variables may be used and automatically
3353 updated by the network boot commands ("bootp" and "rarpboot"),
3354 depending the information provided by your boot server:
3356 bootfile - see above
3357 dnsip - IP address of your Domain Name Server
3358 dnsip2 - IP address of your secondary Domain Name Server
3359 gatewayip - IP address of the Gateway (Router) to use
3360 hostname - Target hostname
3362 netmask - Subnet Mask
3363 rootpath - Pathname of the root filesystem on the NFS server
3364 serverip - see above
3367 There are two special Environment Variables:
3369 serial# - contains hardware identification information such
3370 as type string and/or serial number
3371 ethaddr - Ethernet address
3373 These variables can be set only once (usually during manufacturing of
3374 the board). U-Boot refuses to delete or overwrite these variables
3375 once they have been set once.
3378 Further special Environment Variables:
3380 ver - Contains the U-Boot version string as printed
3381 with the "version" command. This variable is
3382 readonly (see CONFIG_VERSION_VARIABLE).
3385 Please note that changes to some configuration parameters may take
3386 only effect after the next boot (yes, that's just like Windoze :-).
3389 Command Line Parsing:
3390 =====================
3392 There are two different command line parsers available with U-Boot:
3393 the old "simple" one, and the much more powerful "hush" shell:
3395 Old, simple command line parser:
3396 --------------------------------
3398 - supports environment variables (through setenv / saveenv commands)
3399 - several commands on one line, separated by ';'
3400 - variable substitution using "... ${name} ..." syntax
3401 - special characters ('$', ';') can be escaped by prefixing with '\',
3403 setenv bootcmd bootm \${address}
3404 - You can also escape text by enclosing in single apostrophes, for example:
3405 setenv addip 'setenv bootargs $bootargs ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname::off'
3410 - similar to Bourne shell, with control structures like
3411 if...then...else...fi, for...do...done; while...do...done,
3412 until...do...done, ...
3413 - supports environment ("global") variables (through setenv / saveenv
3414 commands) and local shell variables (through standard shell syntax
3415 "name=value"); only environment variables can be used with "run"
3421 (1) If a command line (or an environment variable executed by a "run"
3422 command) contains several commands separated by semicolon, and
3423 one of these commands fails, then the remaining commands will be
3426 (2) If you execute several variables with one call to run (i. e.
3427 calling run with a list of variables as arguments), any failing
3428 command will cause "run" to terminate, i. e. the remaining
3429 variables are not executed.
3431 Note for Redundant Ethernet Interfaces:
3432 =======================================
3434 Some boards come with redundant Ethernet interfaces; U-Boot supports
3435 such configurations and is capable of automatic selection of a
3436 "working" interface when needed. MAC assignment works as follows:
3438 Network interfaces are numbered eth0, eth1, eth2, ... Corresponding
3439 MAC addresses can be stored in the environment as "ethaddr" (=>eth0),
3440 "eth1addr" (=>eth1), "eth2addr", ...
3442 If the network interface stores some valid MAC address (for instance
3443 in SROM), this is used as default address if there is NO correspon-
3444 ding setting in the environment; if the corresponding environment
3445 variable is set, this overrides the settings in the card; that means:
3447 o If the SROM has a valid MAC address, and there is no address in the
3448 environment, the SROM's address is used.
3450 o If there is no valid address in the SROM, and a definition in the
3451 environment exists, then the value from the environment variable is
3454 o If both the SROM and the environment contain a MAC address, and
3455 both addresses are the same, this MAC address is used.
3457 o If both the SROM and the environment contain a MAC address, and the
3458 addresses differ, the value from the environment is used and a
3461 o If neither SROM nor the environment contain a MAC address, an error
3464 If Ethernet drivers implement the 'write_hwaddr' function, valid MAC addresses
3465 will be programmed into hardware as part of the initialization process. This
3466 may be skipped by setting the appropriate 'ethmacskip' environment variable.
3467 The naming convention is as follows:
3468 "ethmacskip" (=>eth0), "eth1macskip" (=>eth1) etc.
3473 U-Boot is capable of booting (and performing other auxiliary operations on)
3474 images in two formats:
3476 New uImage format (FIT)
3477 -----------------------
3479 Flexible and powerful format based on Flattened Image Tree -- FIT (similar
3480 to Flattened Device Tree). It allows the use of images with multiple
3481 components (several kernels, ramdisks, etc.), with contents protected by
3482 SHA1, MD5 or CRC32. More details are found in the doc/uImage.FIT directory.
3488 Old image format is based on binary files which can be basically anything,
3489 preceded by a special header; see the definitions in include/image.h for
3490 details; basically, the header defines the following image properties:
3492 * Target Operating System (Provisions for OpenBSD, NetBSD, FreeBSD,
3493 4.4BSD, Linux, SVR4, Esix, Solaris, Irix, SCO, Dell, NCR, VxWorks,
3494 LynxOS, pSOS, QNX, RTEMS, INTEGRITY;
3495 Currently supported: Linux, NetBSD, VxWorks, QNX, RTEMS, LynxOS,
3497 * Target CPU Architecture (Provisions for Alpha, ARM, AVR32, Intel x86,
3498 IA64, MIPS, Nios II, PowerPC, IBM S390, SuperH, Sparc, Sparc 64 Bit;
3499 Currently supported: ARM, AVR32, Intel x86, MIPS, Nios II, PowerPC).
3500 * Compression Type (uncompressed, gzip, bzip2)
3506 The header is marked by a special Magic Number, and both the header
3507 and the data portions of the image are secured against corruption by
3514 Although U-Boot should support any OS or standalone application
3515 easily, the main focus has always been on Linux during the design of
3518 U-Boot includes many features that so far have been part of some
3519 special "boot loader" code within the Linux kernel. Also, any
3520 "initrd" images to be used are no longer part of one big Linux image;
3521 instead, kernel and "initrd" are separate images. This implementation
3522 serves several purposes:
3524 - the same features can be used for other OS or standalone
3525 applications (for instance: using compressed images to reduce the
3526 Flash memory footprint)
3528 - it becomes much easier to port new Linux kernel versions because
3529 lots of low-level, hardware dependent stuff are done by U-Boot
3531 - the same Linux kernel image can now be used with different "initrd"
3532 images; of course this also means that different kernel images can
3533 be run with the same "initrd". This makes testing easier (you don't
3534 have to build a new "zImage.initrd" Linux image when you just
3535 change a file in your "initrd"). Also, a field-upgrade of the
3536 software is easier now.
3542 Porting Linux to U-Boot based systems:
3543 ---------------------------------------
3545 U-Boot cannot save you from doing all the necessary modifications to
3546 configure the Linux device drivers for use with your target hardware
3547 (no, we don't intend to provide a full virtual machine interface to
3550 But now you can ignore ALL boot loader code (in arch/powerpc/mbxboot).
3552 Just make sure your machine specific header file (for instance
3553 include/asm-ppc/tqm8xx.h) includes the same definition of the Board
3554 Information structure as we define in include/asm-<arch>/u-boot.h,
3555 and make sure that your definition of IMAP_ADDR uses the same value
3556 as your U-Boot configuration in CONFIG_SYS_IMMR.
3559 Configuring the Linux kernel:
3560 -----------------------------
3562 No specific requirements for U-Boot. Make sure you have some root
3563 device (initial ramdisk, NFS) for your target system.
3566 Building a Linux Image:
3567 -----------------------
3569 With U-Boot, "normal" build targets like "zImage" or "bzImage" are
3570 not used. If you use recent kernel source, a new build target
3571 "uImage" will exist which automatically builds an image usable by
3572 U-Boot. Most older kernels also have support for a "pImage" target,
3573 which was introduced for our predecessor project PPCBoot and uses a
3574 100% compatible format.
3583 The "uImage" build target uses a special tool (in 'tools/mkimage') to
3584 encapsulate a compressed Linux kernel image with header information,
3585 CRC32 checksum etc. for use with U-Boot. This is what we are doing:
3587 * build a standard "vmlinux" kernel image (in ELF binary format):
3589 * convert the kernel into a raw binary image:
3591 ${CROSS_COMPILE}-objcopy -O binary \
3592 -R .note -R .comment \
3593 -S vmlinux linux.bin
3595 * compress the binary image:
3599 * package compressed binary image for U-Boot:
3601 mkimage -A ppc -O linux -T kernel -C gzip \
3602 -a 0 -e 0 -n "Linux Kernel Image" \
3603 -d linux.bin.gz uImage
3606 The "mkimage" tool can also be used to create ramdisk images for use
3607 with U-Boot, either separated from the Linux kernel image, or
3608 combined into one file. "mkimage" encapsulates the images with a 64
3609 byte header containing information about target architecture,
3610 operating system, image type, compression method, entry points, time
3611 stamp, CRC32 checksums, etc.
3613 "mkimage" can be called in two ways: to verify existing images and
3614 print the header information, or to build new images.
3616 In the first form (with "-l" option) mkimage lists the information
3617 contained in the header of an existing U-Boot image; this includes
3618 checksum verification:
3620 tools/mkimage -l image
3621 -l ==> list image header information
3623 The second form (with "-d" option) is used to build a U-Boot image
3624 from a "data file" which is used as image payload:
3626 tools/mkimage -A arch -O os -T type -C comp -a addr -e ep \
3627 -n name -d data_file image
3628 -A ==> set architecture to 'arch'
3629 -O ==> set operating system to 'os'
3630 -T ==> set image type to 'type'
3631 -C ==> set compression type 'comp'
3632 -a ==> set load address to 'addr' (hex)
3633 -e ==> set entry point to 'ep' (hex)
3634 -n ==> set image name to 'name'
3635 -d ==> use image data from 'datafile'
3637 Right now, all Linux kernels for PowerPC systems use the same load
3638 address (0x00000000), but the entry point address depends on the
3641 - 2.2.x kernels have the entry point at 0x0000000C,
3642 - 2.3.x and later kernels have the entry point at 0x00000000.
3644 So a typical call to build a U-Boot image would read:
3646 -> tools/mkimage -n '2.4.4 kernel for TQM850L' \
3647 > -A ppc -O linux -T kernel -C gzip -a 0 -e 0 \
3648 > -d /opt/elsk/ppc_8xx/usr/src/linux-2.4.4/arch/powerpc/coffboot/vmlinux.gz \
3649 > examples/uImage.TQM850L
3650 Image Name: 2.4.4 kernel for TQM850L
3651 Created: Wed Jul 19 02:34:59 2000
3652 Image Type: PowerPC Linux Kernel Image (gzip compressed)
3653 Data Size: 335725 Bytes = 327.86 kB = 0.32 MB
3654 Load Address: 0x00000000
3655 Entry Point: 0x00000000
3657 To verify the contents of the image (or check for corruption):
3659 -> tools/mkimage -l examples/uImage.TQM850L
3660 Image Name: 2.4.4 kernel for TQM850L
3661 Created: Wed Jul 19 02:34:59 2000
3662 Image Type: PowerPC Linux Kernel Image (gzip compressed)
3663 Data Size: 335725 Bytes = 327.86 kB = 0.32 MB
3664 Load Address: 0x00000000
3665 Entry Point: 0x00000000
3667 NOTE: for embedded systems where boot time is critical you can trade
3668 speed for memory and install an UNCOMPRESSED image instead: this
3669 needs more space in Flash, but boots much faster since it does not
3670 need to be uncompressed:
3672 -> gunzip /opt/elsk/ppc_8xx/usr/src/linux-2.4.4/arch/powerpc/coffboot/vmlinux.gz
3673 -> tools/mkimage -n '2.4.4 kernel for TQM850L' \
3674 > -A ppc -O linux -T kernel -C none -a 0 -e 0 \
3675 > -d /opt/elsk/ppc_8xx/usr/src/linux-2.4.4/arch/powerpc/coffboot/vmlinux \
3676 > examples/uImage.TQM850L-uncompressed
3677 Image Name: 2.4.4 kernel for TQM850L
3678 Created: Wed Jul 19 02:34:59 2000
3679 Image Type: PowerPC Linux Kernel Image (uncompressed)
3680 Data Size: 792160 Bytes = 773.59 kB = 0.76 MB
3681 Load Address: 0x00000000
3682 Entry Point: 0x00000000
3685 Similar you can build U-Boot images from a 'ramdisk.image.gz' file
3686 when your kernel is intended to use an initial ramdisk:
3688 -> tools/mkimage -n 'Simple Ramdisk Image' \
3689 > -A ppc -O linux -T ramdisk -C gzip \
3690 > -d /LinuxPPC/images/SIMPLE-ramdisk.image.gz examples/simple-initrd
3691 Image Name: Simple Ramdisk Image
3692 Created: Wed Jan 12 14:01:50 2000
3693 Image Type: PowerPC Linux RAMDisk Image (gzip compressed)
3694 Data Size: 566530 Bytes = 553.25 kB = 0.54 MB
3695 Load Address: 0x00000000
3696 Entry Point: 0x00000000
3699 Installing a Linux Image:
3700 -------------------------
3702 To downloading a U-Boot image over the serial (console) interface,
3703 you must convert the image to S-Record format:
3705 objcopy -I binary -O srec examples/image examples/image.srec
3707 The 'objcopy' does not understand the information in the U-Boot
3708 image header, so the resulting S-Record file will be relative to
3709 address 0x00000000. To load it to a given address, you need to
3710 specify the target address as 'offset' parameter with the 'loads'
3713 Example: install the image to address 0x40100000 (which on the
3714 TQM8xxL is in the first Flash bank):
3716 => erase 40100000 401FFFFF
3722 ## Ready for S-Record download ...
3723 ~>examples/image.srec
3724 1 2 3 4 5 6 7 8 9 10 11 12 13 ...
3726 15989 15990 15991 15992
3727 [file transfer complete]
3729 ## Start Addr = 0x00000000
3732 You can check the success of the download using the 'iminfo' command;
3733 this includes a checksum verification so you can be sure no data
3734 corruption happened:
3738 ## Checking Image at 40100000 ...
3739 Image Name: 2.2.13 for initrd on TQM850L
3740 Image Type: PowerPC Linux Kernel Image (gzip compressed)
3741 Data Size: 335725 Bytes = 327 kB = 0 MB
3742 Load Address: 00000000
3743 Entry Point: 0000000c
3744 Verifying Checksum ... OK
3750 The "bootm" command is used to boot an application that is stored in
3751 memory (RAM or Flash). In case of a Linux kernel image, the contents
3752 of the "bootargs" environment variable is passed to the kernel as
3753 parameters. You can check and modify this variable using the
3754 "printenv" and "setenv" commands:
3757 => printenv bootargs
3758 bootargs=root=/dev/ram
3760 => setenv bootargs root=/dev/nfs rw nfsroot=10.0.0.2:/LinuxPPC nfsaddrs=10.0.0.99:10.0.0.2
3762 => printenv bootargs
3763 bootargs=root=/dev/nfs rw nfsroot=10.0.0.2:/LinuxPPC nfsaddrs=10.0.0.99:10.0.0.2
3766 ## Booting Linux kernel at 40020000 ...
3767 Image Name: 2.2.13 for NFS on TQM850L
3768 Image Type: PowerPC Linux Kernel Image (gzip compressed)
3769 Data Size: 381681 Bytes = 372 kB = 0 MB
3770 Load Address: 00000000
3771 Entry Point: 0000000c
3772 Verifying Checksum ... OK
3773 Uncompressing Kernel Image ... OK
3774 Linux version 2.2.13 (wd@denx.local.net) (gcc version 2.95.2 19991024 (release)) #1 Wed Jul 19 02:35:17 MEST 2000
3775 Boot arguments: root=/dev/nfs rw nfsroot=10.0.0.2:/LinuxPPC nfsaddrs=10.0.0.99:10.0.0.2
3776 time_init: decrementer frequency = 187500000/60
3777 Calibrating delay loop... 49.77 BogoMIPS
3778 Memory: 15208k available (700k kernel code, 444k data, 32k init) [c0000000,c1000000]
3781 If you want to boot a Linux kernel with initial RAM disk, you pass
3782 the memory addresses of both the kernel and the initrd image (PPBCOOT
3783 format!) to the "bootm" command:
3785 => imi 40100000 40200000
3787 ## Checking Image at 40100000 ...
3788 Image Name: 2.2.13 for initrd on TQM850L
3789 Image Type: PowerPC Linux Kernel Image (gzip compressed)
3790 Data Size: 335725 Bytes = 327 kB = 0 MB
3791 Load Address: 00000000
3792 Entry Point: 0000000c
3793 Verifying Checksum ... OK
3795 ## Checking Image at 40200000 ...
3796 Image Name: Simple Ramdisk Image
3797 Image Type: PowerPC Linux RAMDisk Image (gzip compressed)
3798 Data Size: 566530 Bytes = 553 kB = 0 MB
3799 Load Address: 00000000
3800 Entry Point: 00000000
3801 Verifying Checksum ... OK
3803 => bootm 40100000 40200000
3804 ## Booting Linux kernel at 40100000 ...
3805 Image Name: 2.2.13 for initrd on TQM850L
3806 Image Type: PowerPC Linux Kernel Image (gzip compressed)
3807 Data Size: 335725 Bytes = 327 kB = 0 MB
3808 Load Address: 00000000
3809 Entry Point: 0000000c
3810 Verifying Checksum ... OK
3811 Uncompressing Kernel Image ... OK
3812 ## Loading RAMDisk Image at 40200000 ...
3813 Image Name: Simple Ramdisk Image
3814 Image Type: PowerPC Linux RAMDisk Image (gzip compressed)
3815 Data Size: 566530 Bytes = 553 kB = 0 MB
3816 Load Address: 00000000
3817 Entry Point: 00000000
3818 Verifying Checksum ... OK
3819 Loading Ramdisk ... OK
3820 Linux version 2.2.13 (wd@denx.local.net) (gcc version 2.95.2 19991024 (release)) #1 Wed Jul 19 02:32:08 MEST 2000
3821 Boot arguments: root=/dev/ram
3822 time_init: decrementer frequency = 187500000/60
3823 Calibrating delay loop... 49.77 BogoMIPS
3825 RAMDISK: Compressed image found at block 0
3826 VFS: Mounted root (ext2 filesystem).
3830 Boot Linux and pass a flat device tree:
3833 First, U-Boot must be compiled with the appropriate defines. See the section
3834 titled "Linux Kernel Interface" above for a more in depth explanation. The
3835 following is an example of how to start a kernel and pass an updated
3841 oft=oftrees/mpc8540ads.dtb
3842 => tftp $oftaddr $oft
3843 Speed: 1000, full duplex
3845 TFTP from server 192.168.1.1; our IP address is 192.168.1.101
3846 Filename 'oftrees/mpc8540ads.dtb'.
3847 Load address: 0x300000
3850 Bytes transferred = 4106 (100a hex)
3851 => tftp $loadaddr $bootfile
3852 Speed: 1000, full duplex
3854 TFTP from server 192.168.1.1; our IP address is 192.168.1.2
3856 Load address: 0x200000
3857 Loading:############
3859 Bytes transferred = 1029407 (fb51f hex)
3864 => bootm $loadaddr - $oftaddr
3865 ## Booting image at 00200000 ...
3866 Image Name: Linux-2.6.17-dirty
3867 Image Type: PowerPC Linux Kernel Image (gzip compressed)
3868 Data Size: 1029343 Bytes = 1005.2 kB
3869 Load Address: 00000000
3870 Entry Point: 00000000
3871 Verifying Checksum ... OK
3872 Uncompressing Kernel Image ... OK
3873 Booting using flat device tree at 0x300000
3874 Using MPC85xx ADS machine description
3875 Memory CAM mapping: CAM0=256Mb, CAM1=256Mb, CAM2=0Mb residual: 0Mb
3879 More About U-Boot Image Types:
3880 ------------------------------
3882 U-Boot supports the following image types:
3884 "Standalone Programs" are directly runnable in the environment
3885 provided by U-Boot; it is expected that (if they behave
3886 well) you can continue to work in U-Boot after return from
3887 the Standalone Program.
3888 "OS Kernel Images" are usually images of some Embedded OS which
3889 will take over control completely. Usually these programs
3890 will install their own set of exception handlers, device
3891 drivers, set up the MMU, etc. - this means, that you cannot
3892 expect to re-enter U-Boot except by resetting the CPU.
3893 "RAMDisk Images" are more or less just data blocks, and their
3894 parameters (address, size) are passed to an OS kernel that is
3896 "Multi-File Images" contain several images, typically an OS
3897 (Linux) kernel image and one or more data images like
3898 RAMDisks. This construct is useful for instance when you want
3899 to boot over the network using BOOTP etc., where the boot
3900 server provides just a single image file, but you want to get
3901 for instance an OS kernel and a RAMDisk image.
3903 "Multi-File Images" start with a list of image sizes, each
3904 image size (in bytes) specified by an "uint32_t" in network
3905 byte order. This list is terminated by an "(uint32_t)0".
3906 Immediately after the terminating 0 follow the images, one by
3907 one, all aligned on "uint32_t" boundaries (size rounded up to
3908 a multiple of 4 bytes).
3910 "Firmware Images" are binary images containing firmware (like
3911 U-Boot or FPGA images) which usually will be programmed to
3914 "Script files" are command sequences that will be executed by
3915 U-Boot's command interpreter; this feature is especially
3916 useful when you configure U-Boot to use a real shell (hush)
3917 as command interpreter.
3923 One of the features of U-Boot is that you can dynamically load and
3924 run "standalone" applications, which can use some resources of
3925 U-Boot like console I/O functions or interrupt services.
3927 Two simple examples are included with the sources:
3932 'examples/hello_world.c' contains a small "Hello World" Demo
3933 application; it is automatically compiled when you build U-Boot.
3934 It's configured to run at address 0x00040004, so you can play with it
3938 ## Ready for S-Record download ...
3939 ~>examples/hello_world.srec
3940 1 2 3 4 5 6 7 8 9 10 11 ...
3941 [file transfer complete]
3943 ## Start Addr = 0x00040004
3945 => go 40004 Hello World! This is a test.
3946 ## Starting application at 0x00040004 ...
3957 Hit any key to exit ...
3959 ## Application terminated, rc = 0x0
3961 Another example, which demonstrates how to register a CPM interrupt
3962 handler with the U-Boot code, can be found in 'examples/timer.c'.
3963 Here, a CPM timer is set up to generate an interrupt every second.
3964 The interrupt service routine is trivial, just printing a '.'
3965 character, but this is just a demo program. The application can be
3966 controlled by the following keys:
3968 ? - print current values og the CPM Timer registers
3969 b - enable interrupts and start timer
3970 e - stop timer and disable interrupts
3971 q - quit application
3974 ## Ready for S-Record download ...
3975 ~>examples/timer.srec
3976 1 2 3 4 5 6 7 8 9 10 11 ...
3977 [file transfer complete]
3979 ## Start Addr = 0x00040004
3982 ## Starting application at 0x00040004 ...
3985 tgcr @ 0xfff00980, tmr @ 0xfff00990, trr @ 0xfff00994, tcr @ 0xfff00998, tcn @ 0xfff0099c, ter @ 0xfff009b0
3988 [q, b, e, ?] Set interval 1000000 us
3991 [q, b, e, ?] ........
3992 tgcr=0x1, tmr=0xff1c, trr=0x3d09, tcr=0x0, tcn=0xef6, ter=0x0
3995 tgcr=0x1, tmr=0xff1c, trr=0x3d09, tcr=0x0, tcn=0x2ad4, ter=0x0
3998 tgcr=0x1, tmr=0xff1c, trr=0x3d09, tcr=0x0, tcn=0x1efc, ter=0x0
4001 tgcr=0x1, tmr=0xff1c, trr=0x3d09, tcr=0x0, tcn=0x169d, ter=0x0
4003 [q, b, e, ?] ...Stopping timer
4005 [q, b, e, ?] ## Application terminated, rc = 0x0
4011 Over time, many people have reported problems when trying to use the
4012 "minicom" terminal emulation program for serial download. I (wd)
4013 consider minicom to be broken, and recommend not to use it. Under
4014 Unix, I recommend to use C-Kermit for general purpose use (and
4015 especially for kermit binary protocol download ("loadb" command), and
4016 use "cu" for S-Record download ("loads" command).
4018 Nevertheless, if you absolutely want to use it try adding this
4019 configuration to your "File transfer protocols" section:
4021 Name Program Name U/D FullScr IO-Red. Multi
4022 X kermit /usr/bin/kermit -i -l %l -s Y U Y N N
4023 Y kermit /usr/bin/kermit -i -l %l -r N D Y N N
4029 Starting at version 0.9.2, U-Boot supports NetBSD both as host
4030 (build U-Boot) and target system (boots NetBSD/mpc8xx).
4032 Building requires a cross environment; it is known to work on
4033 NetBSD/i386 with the cross-powerpc-netbsd-1.3 package (you will also
4034 need gmake since the Makefiles are not compatible with BSD make).
4035 Note that the cross-powerpc package does not install include files;
4036 attempting to build U-Boot will fail because <machine/ansi.h> is
4037 missing. This file has to be installed and patched manually:
4039 # cd /usr/pkg/cross/powerpc-netbsd/include
4041 # ln -s powerpc machine
4042 # cp /usr/src/sys/arch/powerpc/include/ansi.h powerpc/ansi.h
4043 # ${EDIT} powerpc/ansi.h ## must remove __va_list, _BSD_VA_LIST
4045 Native builds *don't* work due to incompatibilities between native
4046 and U-Boot include files.
4048 Booting assumes that (the first part of) the image booted is a
4049 stage-2 loader which in turn loads and then invokes the kernel
4050 proper. Loader sources will eventually appear in the NetBSD source
4051 tree (probably in sys/arc/mpc8xx/stand/u-boot_stage2/); in the
4052 meantime, see ftp://ftp.denx.de/pub/u-boot/ppcboot_stage2.tar.gz
4055 Implementation Internals:
4056 =========================
4058 The following is not intended to be a complete description of every
4059 implementation detail. However, it should help to understand the
4060 inner workings of U-Boot and make it easier to port it to custom
4064 Initial Stack, Global Data:
4065 ---------------------------
4067 The implementation of U-Boot is complicated by the fact that U-Boot
4068 starts running out of ROM (flash memory), usually without access to
4069 system RAM (because the memory controller is not initialized yet).
4070 This means that we don't have writable Data or BSS segments, and BSS
4071 is not initialized as zero. To be able to get a C environment working
4072 at all, we have to allocate at least a minimal stack. Implementation
4073 options for this are defined and restricted by the CPU used: Some CPU
4074 models provide on-chip memory (like the IMMR area on MPC8xx and
4075 MPC826x processors), on others (parts of) the data cache can be
4076 locked as (mis-) used as memory, etc.
4078 Chris Hallinan posted a good summary of these issues to the
4079 U-Boot mailing list:
4081 Subject: RE: [U-Boot-Users] RE: More On Memory Bank x (nothingness)?
4082 From: "Chris Hallinan" <clh@net1plus.com>
4083 Date: Mon, 10 Feb 2003 16:43:46 -0500 (22:43 MET)
4086 Correct me if I'm wrong, folks, but the way I understand it
4087 is this: Using DCACHE as initial RAM for Stack, etc, does not
4088 require any physical RAM backing up the cache. The cleverness
4089 is that the cache is being used as a temporary supply of
4090 necessary storage before the SDRAM controller is setup. It's
4091 beyond the scope of this list to explain the details, but you
4092 can see how this works by studying the cache architecture and
4093 operation in the architecture and processor-specific manuals.
4095 OCM is On Chip Memory, which I believe the 405GP has 4K. It
4096 is another option for the system designer to use as an
4097 initial stack/RAM area prior to SDRAM being available. Either
4098 option should work for you. Using CS 4 should be fine if your
4099 board designers haven't used it for something that would
4100 cause you grief during the initial boot! It is frequently not
4103 CONFIG_SYS_INIT_RAM_ADDR should be somewhere that won't interfere
4104 with your processor/board/system design. The default value
4105 you will find in any recent u-boot distribution in
4106 walnut.h should work for you. I'd set it to a value larger
4107 than your SDRAM module. If you have a 64MB SDRAM module, set
4108 it above 400_0000. Just make sure your board has no resources
4109 that are supposed to respond to that address! That code in
4110 start.S has been around a while and should work as is when
4111 you get the config right.
4116 It is essential to remember this, since it has some impact on the C
4117 code for the initialization procedures:
4119 * Initialized global data (data segment) is read-only. Do not attempt
4122 * Do not use any uninitialized global data (or implicitely initialized
4123 as zero data - BSS segment) at all - this is undefined, initiali-
4124 zation is performed later (when relocating to RAM).
4126 * Stack space is very limited. Avoid big data buffers or things like
4129 Having only the stack as writable memory limits means we cannot use
4130 normal global data to share information beween the code. But it
4131 turned out that the implementation of U-Boot can be greatly
4132 simplified by making a global data structure (gd_t) available to all
4133 functions. We could pass a pointer to this data as argument to _all_
4134 functions, but this would bloat the code. Instead we use a feature of
4135 the GCC compiler (Global Register Variables) to share the data: we
4136 place a pointer (gd) to the global data into a register which we
4137 reserve for this purpose.
4139 When choosing a register for such a purpose we are restricted by the
4140 relevant (E)ABI specifications for the current architecture, and by
4141 GCC's implementation.
4143 For PowerPC, the following registers have specific use:
4145 R2: reserved for system use
4146 R3-R4: parameter passing and return values
4147 R5-R10: parameter passing
4148 R13: small data area pointer
4152 (U-Boot also uses R12 as internal GOT pointer. r12
4153 is a volatile register so r12 needs to be reset when
4154 going back and forth between asm and C)
4156 ==> U-Boot will use R2 to hold a pointer to the global data
4158 Note: on PPC, we could use a static initializer (since the
4159 address of the global data structure is known at compile time),
4160 but it turned out that reserving a register results in somewhat
4161 smaller code - although the code savings are not that big (on
4162 average for all boards 752 bytes for the whole U-Boot image,
4163 624 text + 127 data).
4165 On Blackfin, the normal C ABI (except for P3) is followed as documented here:
4166 http://docs.blackfin.uclinux.org/doku.php?id=application_binary_interface
4168 ==> U-Boot will use P3 to hold a pointer to the global data
4170 On ARM, the following registers are used:
4172 R0: function argument word/integer result
4173 R1-R3: function argument word
4175 R10: stack limit (used only if stack checking if enabled)
4176 R11: argument (frame) pointer
4177 R12: temporary workspace
4180 R15: program counter
4182 ==> U-Boot will use R8 to hold a pointer to the global data
4184 On Nios II, the ABI is documented here:
4185 http://www.altera.com/literature/hb/nios2/n2cpu_nii51016.pdf
4187 ==> U-Boot will use gp to hold a pointer to the global data
4189 Note: on Nios II, we give "-G0" option to gcc and don't use gp
4190 to access small data sections, so gp is free.
4192 NOTE: DECLARE_GLOBAL_DATA_PTR must be used with file-global scope,
4193 or current versions of GCC may "optimize" the code too much.
4198 U-Boot runs in system state and uses physical addresses, i.e. the
4199 MMU is not used either for address mapping nor for memory protection.
4201 The available memory is mapped to fixed addresses using the memory
4202 controller. In this process, a contiguous block is formed for each
4203 memory type (Flash, SDRAM, SRAM), even when it consists of several
4204 physical memory banks.
4206 U-Boot is installed in the first 128 kB of the first Flash bank (on
4207 TQM8xxL modules this is the range 0x40000000 ... 0x4001FFFF). After
4208 booting and sizing and initializing DRAM, the code relocates itself
4209 to the upper end of DRAM. Immediately below the U-Boot code some
4210 memory is reserved for use by malloc() [see CONFIG_SYS_MALLOC_LEN
4211 configuration setting]. Below that, a structure with global Board
4212 Info data is placed, followed by the stack (growing downward).
4214 Additionally, some exception handler code is copied to the low 8 kB
4215 of DRAM (0x00000000 ... 0x00001FFF).
4217 So a typical memory configuration with 16 MB of DRAM could look like
4220 0x0000 0000 Exception Vector code
4223 0x0000 2000 Free for Application Use
4229 0x00FB FF20 Monitor Stack (Growing downward)
4230 0x00FB FFAC Board Info Data and permanent copy of global data
4231 0x00FC 0000 Malloc Arena
4234 0x00FE 0000 RAM Copy of Monitor Code
4235 ... eventually: LCD or video framebuffer
4236 ... eventually: pRAM (Protected RAM - unchanged by reset)
4237 0x00FF FFFF [End of RAM]
4240 System Initialization:
4241 ----------------------
4243 In the reset configuration, U-Boot starts at the reset entry point
4244 (on most PowerPC systems at address 0x00000100). Because of the reset
4245 configuration for CS0# this is a mirror of the onboard Flash memory.
4246 To be able to re-map memory U-Boot then jumps to its link address.
4247 To be able to implement the initialization code in C, a (small!)
4248 initial stack is set up in the internal Dual Ported RAM (in case CPUs
4249 which provide such a feature like MPC8xx or MPC8260), or in a locked
4250 part of the data cache. After that, U-Boot initializes the CPU core,
4251 the caches and the SIU.
4253 Next, all (potentially) available memory banks are mapped using a
4254 preliminary mapping. For example, we put them on 512 MB boundaries
4255 (multiples of 0x20000000: SDRAM on 0x00000000 and 0x20000000, Flash
4256 on 0x40000000 and 0x60000000, SRAM on 0x80000000). Then UPM A is
4257 programmed for SDRAM access. Using the temporary configuration, a
4258 simple memory test is run that determines the size of the SDRAM
4261 When there is more than one SDRAM bank, and the banks are of
4262 different size, the largest is mapped first. For equal size, the first
4263 bank (CS2#) is mapped first. The first mapping is always for address
4264 0x00000000, with any additional banks following immediately to create
4265 contiguous memory starting from 0.
4267 Then, the monitor installs itself at the upper end of the SDRAM area
4268 and allocates memory for use by malloc() and for the global Board
4269 Info data; also, the exception vector code is copied to the low RAM
4270 pages, and the final stack is set up.
4272 Only after this relocation will you have a "normal" C environment;
4273 until that you are restricted in several ways, mostly because you are
4274 running from ROM, and because the code will have to be relocated to a
4278 U-Boot Porting Guide:
4279 ----------------------
4281 [Based on messages by Jerry Van Baren in the U-Boot-Users mailing
4285 int main(int argc, char *argv[])
4287 sighandler_t no_more_time;
4289 signal(SIGALRM, no_more_time);
4290 alarm(PROJECT_DEADLINE - toSec (3 * WEEK));
4292 if (available_money > available_manpower) {
4293 Pay consultant to port U-Boot;
4297 Download latest U-Boot source;
4299 Subscribe to u-boot mailing list;
4302 email("Hi, I am new to U-Boot, how do I get started?");
4305 Read the README file in the top level directory;
4306 Read http://www.denx.de/twiki/bin/view/DULG/Manual;
4307 Read applicable doc/*.README;
4308 Read the source, Luke;
4309 /* find . -name "*.[chS]" | xargs grep -i <keyword> */
4312 if (available_money > toLocalCurrency ($2500))
4315 Add a lot of aggravation and time;
4317 if (a similar board exists) { /* hopefully... */
4318 cp -a board/<similar> board/<myboard>
4319 cp include/configs/<similar>.h include/configs/<myboard>.h
4321 Create your own board support subdirectory;
4322 Create your own board include/configs/<myboard>.h file;
4324 Edit new board/<myboard> files
4325 Edit new include/configs/<myboard>.h
4330 Add / modify source code;
4334 email("Hi, I am having problems...");
4336 Send patch file to the U-Boot email list;
4337 if (reasonable critiques)
4338 Incorporate improvements from email list code review;
4340 Defend code as written;
4346 void no_more_time (int sig)
4355 All contributions to U-Boot should conform to the Linux kernel
4356 coding style; see the file "Documentation/CodingStyle" and the script
4357 "scripts/Lindent" in your Linux kernel source directory. In sources
4358 originating from U-Boot a style corresponding to "Lindent -pcs" (adding
4359 spaces before parameters to function calls) is actually used.
4361 Source files originating from a different project (for example the
4362 MTD subsystem) are generally exempt from these guidelines and are not
4363 reformated to ease subsequent migration to newer versions of those
4366 Please note that U-Boot is implemented in C (and to some small parts in
4367 Assembler); no C++ is used, so please do not use C++ style comments (//)
4370 Please also stick to the following formatting rules:
4371 - remove any trailing white space
4372 - use TAB characters for indentation, not spaces
4373 - make sure NOT to use DOS '\r\n' line feeds
4374 - do not add more than 2 empty lines to source files
4375 - do not add trailing empty lines to source files
4377 Submissions which do not conform to the standards may be returned
4378 with a request to reformat the changes.
4384 Since the number of patches for U-Boot is growing, we need to
4385 establish some rules. Submissions which do not conform to these rules
4386 may be rejected, even when they contain important and valuable stuff.
4388 Please see http://www.denx.de/wiki/U-Boot/Patches for details.
4390 Patches shall be sent to the u-boot mailing list <u-boot@lists.denx.de>;
4391 see http://lists.denx.de/mailman/listinfo/u-boot
4393 When you send a patch, please include the following information with
4396 * For bug fixes: a description of the bug and how your patch fixes
4397 this bug. Please try to include a way of demonstrating that the
4398 patch actually fixes something.
4400 * For new features: a description of the feature and your
4403 * A CHANGELOG entry as plaintext (separate from the patch)
4405 * For major contributions, your entry to the CREDITS file
4407 * When you add support for a new board, don't forget to add this
4408 board to the MAKEALL script, too.
4410 * If your patch adds new configuration options, don't forget to
4411 document these in the README file.
4413 * The patch itself. If you are using git (which is *strongly*
4414 recommended) you can easily generate the patch using the
4415 "git-format-patch". If you then use "git-send-email" to send it to
4416 the U-Boot mailing list, you will avoid most of the common problems
4417 with some other mail clients.
4419 If you cannot use git, use "diff -purN OLD NEW". If your version of
4420 diff does not support these options, then get the latest version of
4423 The current directory when running this command shall be the parent
4424 directory of the U-Boot source tree (i. e. please make sure that
4425 your patch includes sufficient directory information for the
4428 We prefer patches as plain text. MIME attachments are discouraged,
4429 and compressed attachments must not be used.
4431 * If one logical set of modifications affects or creates several
4432 files, all these changes shall be submitted in a SINGLE patch file.
4434 * Changesets that contain different, unrelated modifications shall be
4435 submitted as SEPARATE patches, one patch per changeset.
4440 * Before sending the patch, run the MAKEALL script on your patched
4441 source tree and make sure that no errors or warnings are reported
4442 for any of the boards.
4444 * Keep your modifications to the necessary minimum: A patch
4445 containing several unrelated changes or arbitrary reformats will be
4446 returned with a request to re-formatting / split it.
4448 * If you modify existing code, make sure that your new code does not
4449 add to the memory footprint of the code ;-) Small is beautiful!
4450 When adding new features, these should compile conditionally only
4451 (using #ifdef), and the resulting code with the new feature
4452 disabled must not need more memory than the old code without your
4455 * Remember that there is a size limit of 100 kB per message on the
4456 u-boot mailing list. Bigger patches will be moderated. If they are
4457 reasonable and not too big, they will be acknowledged. But patches
4458 bigger than the size limit should be avoided.