4 select ARCH_HAVE_CUSTOM_GPIO_H
6 select HAVE_DMA_API_DEBUG
7 select HAVE_IDE if PCI || ISA || PCMCIA
9 select HAVE_DMA_CONTIGUOUS if MMU
12 select SYS_SUPPORTS_APM_EMULATION
13 select GENERIC_ATOMIC64 if (CPU_V6 || !CPU_32v6K || !AEABI)
14 select ARCH_HAS_ATOMIC64_DEC_IF_POSITIVE
15 select HAVE_OPROFILE if (HAVE_PERF_EVENTS)
16 select HAVE_ARCH_JUMP_LABEL if !XIP_KERNEL
18 select HAVE_ARCH_TRACEHOOK
19 select HAVE_SYSCALL_TRACEPOINTS
20 select HAVE_KPROBES if !XIP_KERNEL
21 select HAVE_KRETPROBES if (HAVE_KPROBES)
22 select HAVE_FUNCTION_TRACER if (!XIP_KERNEL)
23 select HAVE_FTRACE_MCOUNT_RECORD if (!XIP_KERNEL)
24 select HAVE_DYNAMIC_FTRACE if (!XIP_KERNEL)
25 select HAVE_FUNCTION_GRAPH_TRACER if (!THUMB2_KERNEL)
26 select ARCH_BINFMT_ELF_RANDOMIZE_PIE
27 select HAVE_GENERIC_DMA_COHERENT
28 select HAVE_KERNEL_GZIP
29 select HAVE_KERNEL_LZO
30 select HAVE_KERNEL_LZMA
33 select HAVE_PERF_EVENTS
34 select PERF_USE_VMALLOC
35 select HAVE_REGS_AND_STACK_ACCESS_API
36 select HAVE_HW_BREAKPOINT if (PERF_EVENTS && (CPU_V6 || CPU_V6K || CPU_V7))
37 select HAVE_C_RECORDMCOUNT
38 select HAVE_GENERIC_HARDIRQS
39 select HARDIRQS_SW_RESEND
40 select GENERIC_IRQ_PROBE
41 select GENERIC_IRQ_SHOW
42 select ARCH_WANT_IPC_PARSE_VERSION
43 select HARDIRQS_SW_RESEND
44 select CPU_PM if (SUSPEND || CPU_IDLE)
45 select GENERIC_PCI_IOMAP
47 select GENERIC_SMP_IDLE_THREAD
49 select GENERIC_CLOCKEVENTS_BROADCAST if SMP
50 select GENERIC_STRNCPY_FROM_USER
51 select GENERIC_STRNLEN_USER
52 select DCACHE_WORD_ACCESS if (CPU_V6 || CPU_V6K || CPU_V7) && !CPU_BIG_ENDIAN
53 select HAVE_MOD_ARCH_SPECIFIC if ARM_UNWIND
54 select MODULES_USE_ELF_REL
55 select GENERIC_KERNEL_THREAD
57 The ARM series is a line of low-power-consumption RISC chip designs
58 licensed by ARM Ltd and targeted at embedded applications and
59 handhelds such as the Compaq IPAQ. ARM-based PCs are no longer
60 manufactured, but legacy ARM-based PC hardware remains popular in
61 Europe. There is an ARM Linux project with a web page at
62 <http://www.arm.linux.org.uk/>.
64 config ARM_HAS_SG_CHAIN
67 config NEED_SG_DMA_LENGTH
70 config ARM_DMA_USE_IOMMU
71 select NEED_SG_DMA_LENGTH
72 select ARM_HAS_SG_CHAIN
81 config SYS_SUPPORTS_APM_EMULATION
89 select GENERIC_ALLOCATOR
100 The Extended Industry Standard Architecture (EISA) bus was
101 developed as an open alternative to the IBM MicroChannel bus.
103 The EISA bus provided some of the features of the IBM MicroChannel
104 bus while maintaining backward compatibility with cards made for
105 the older ISA bus. The EISA bus saw limited use between 1988 and
106 1995 when it was made obsolete by the PCI bus.
108 Say Y here if you are building a kernel for an EISA-based machine.
115 config STACKTRACE_SUPPORT
119 config HAVE_LATENCYTOP_SUPPORT
124 config LOCKDEP_SUPPORT
128 config TRACE_IRQFLAGS_SUPPORT
132 config RWSEM_GENERIC_SPINLOCK
136 config RWSEM_XCHGADD_ALGORITHM
139 config ARCH_HAS_ILOG2_U32
142 config ARCH_HAS_ILOG2_U64
145 config ARCH_HAS_CPUFREQ
148 Internal node to signify that the ARCH has CPUFREQ support
149 and that the relevant menu configurations are displayed for
152 config GENERIC_HWEIGHT
156 config GENERIC_CALIBRATE_DELAY
160 config ARCH_MAY_HAVE_PC_FDC
166 config NEED_DMA_MAP_STATE
169 config ARCH_HAS_DMA_SET_COHERENT_MASK
172 config GENERIC_ISA_DMA
178 config NEED_RET_TO_USER
186 default 0xffff0000 if MMU || CPU_HIGH_VECTOR
187 default DRAM_BASE if REMAP_VECTORS_TO_RAM
190 The base address of exception vectors.
192 config ARM_PATCH_PHYS_VIRT
193 bool "Patch physical to virtual translations at runtime" if EMBEDDED
195 depends on !XIP_KERNEL && MMU
196 depends on !ARCH_REALVIEW || !SPARSEMEM
198 Patch phys-to-virt and virt-to-phys translation functions at
199 boot and module load time according to the position of the
200 kernel in system memory.
202 This can only be used with non-XIP MMU kernels where the base
203 of physical memory is at a 16MB boundary.
205 Only disable this option if you know that you do not require
206 this feature (eg, building a kernel for a single machine) and
207 you need to shrink the kernel to the minimal size.
209 config NEED_MACH_GPIO_H
212 Select this when mach/gpio.h is required to provide special
213 definitions for this platform. The need for mach/gpio.h should
214 be avoided when possible.
216 config NEED_MACH_IO_H
219 Select this when mach/io.h is required to provide special
220 definitions for this platform. The need for mach/io.h should
221 be avoided when possible.
223 config NEED_MACH_MEMORY_H
226 Select this when mach/memory.h is required to provide special
227 definitions for this platform. The need for mach/memory.h should
228 be avoided when possible.
231 hex "Physical address of main memory" if MMU
232 depends on !ARM_PATCH_PHYS_VIRT && !NEED_MACH_MEMORY_H
233 default DRAM_BASE if !MMU
235 Please provide the physical address corresponding to the
236 location of main memory in your system.
242 source "init/Kconfig"
244 source "kernel/Kconfig.freezer"
249 bool "MMU-based Paged Memory Management Support"
252 Select if you want MMU-based virtualised addressing space
253 support by paged memory management. If unsure, say 'Y'.
256 # The "ARM system type" choice list is ordered alphabetically by option
257 # text. Please add new entries in the option alphabetic order.
260 prompt "ARM system type"
261 default ARCH_MULTIPLATFORM
263 config ARCH_MULTIPLATFORM
264 bool "Allow multiple platforms to be selected"
265 select ARM_PATCH_PHYS_VIRT
268 select MULTI_IRQ_HANDLER
273 config ARCH_INTEGRATOR
274 bool "ARM Ltd. Integrator family"
276 select ARCH_HAS_CPUFREQ
278 select COMMON_CLK_VERSATILE
281 select GENERIC_CLOCKEVENTS
282 select PLAT_VERSATILE
283 select PLAT_VERSATILE_FPGA_IRQ
284 select NEED_MACH_MEMORY_H
286 select MULTI_IRQ_HANDLER
288 Support for ARM's Integrator platform.
291 bool "ARM Ltd. RealView family"
294 select COMMON_CLK_VERSATILE
296 select GENERIC_CLOCKEVENTS
297 select ARCH_WANT_OPTIONAL_GPIOLIB
298 select PLAT_VERSATILE
299 select PLAT_VERSATILE_CLCD
300 select ARM_TIMER_SP804
301 select GPIO_PL061 if GPIOLIB
302 select NEED_MACH_MEMORY_H
304 This enables support for ARM Ltd RealView boards.
306 config ARCH_VERSATILE
307 bool "ARM Ltd. Versatile family"
311 select HAVE_MACH_CLKDEV
313 select GENERIC_CLOCKEVENTS
314 select ARCH_WANT_OPTIONAL_GPIOLIB
315 select PLAT_VERSATILE
316 select PLAT_VERSATILE_CLOCK
317 select PLAT_VERSATILE_CLCD
318 select PLAT_VERSATILE_FPGA_IRQ
319 select ARM_TIMER_SP804
321 This enables support for ARM Ltd Versatile board.
325 select ARCH_REQUIRE_GPIOLIB
329 select NEED_MACH_GPIO_H
330 select NEED_MACH_IO_H if PCCARD
332 This enables support for systems based on Atmel
333 AT91RM9200 and AT91SAM9* processors.
336 bool "Broadcom BCM2835 family"
337 select ARCH_WANT_OPTIONAL_GPIOLIB
339 select ARM_ERRATA_411920
340 select ARM_TIMER_SP804
344 select GENERIC_CLOCKEVENTS
345 select MULTI_IRQ_HANDLER
349 This enables support for the Broadcom BCM2835 SoC. This SoC is
350 use in the Raspberry Pi, and Roku 2 devices.
353 bool "Cirrus Logic CLPS711x/EP721x/EP731x-based"
355 select ARCH_USES_GETTIMEOFFSET
358 select NEED_MACH_MEMORY_H
360 Support for Cirrus Logic 711x/721x/731x based boards.
363 bool "Cavium Networks CNS3XXX family"
365 select GENERIC_CLOCKEVENTS
367 select MIGHT_HAVE_CACHE_L2X0
368 select MIGHT_HAVE_PCI
369 select PCI_DOMAINS if PCI
371 Support for Cavium Networks CNS3XXX platform.
374 bool "Cortina Systems Gemini"
376 select ARCH_REQUIRE_GPIOLIB
377 select ARCH_USES_GETTIMEOFFSET
379 Support for the Cortina Systems Gemini family SoCs
384 select ARCH_REQUIRE_GPIOLIB
385 select GENERIC_CLOCKEVENTS
387 select GENERIC_IRQ_CHIP
388 select MIGHT_HAVE_CACHE_L2X0
393 Support for CSR SiRFprimaII/Marco/Polo platforms
400 select ARCH_USES_GETTIMEOFFSET
401 select NEED_MACH_IO_H
402 select NEED_MACH_MEMORY_H
404 This is an evaluation board for the StrongARM processor available
405 from Digital. It has limited hardware on-board, including an
406 Ethernet interface, two PCMCIA sockets, two serial ports and a
415 select ARCH_REQUIRE_GPIOLIB
416 select ARCH_HAS_HOLES_MEMORYMODEL
417 select ARCH_USES_GETTIMEOFFSET
418 select NEED_MACH_MEMORY_H
420 This enables support for the Cirrus EP93xx series of CPUs.
422 config ARCH_FOOTBRIDGE
426 select GENERIC_CLOCKEVENTS
428 select NEED_MACH_IO_H if !MMU
429 select NEED_MACH_MEMORY_H
431 Support for systems based on the DC21285 companion chip
432 ("FootBridge"), such as the Simtec CATS and the Rebel NetWinder.
435 bool "Freescale MXC/iMX-based"
436 select GENERIC_CLOCKEVENTS
437 select ARCH_REQUIRE_GPIOLIB
440 select GENERIC_IRQ_CHIP
441 select MULTI_IRQ_HANDLER
445 Support for Freescale MXC/iMX-based family of processors
448 bool "Freescale MXS-based"
449 select GENERIC_CLOCKEVENTS
450 select ARCH_REQUIRE_GPIOLIB
454 select HAVE_CLK_PREPARE
455 select MULTI_IRQ_HANDLER
460 Support for Freescale MXS-based family of processors
463 bool "Hilscher NetX based"
467 select GENERIC_CLOCKEVENTS
469 This enables support for systems based on the Hilscher NetX Soc
472 bool "Hynix HMS720x-based"
475 select ARCH_USES_GETTIMEOFFSET
477 This enables support for systems based on the Hynix HMS720x
485 select ARCH_SUPPORTS_MSI
487 select NEED_MACH_MEMORY_H
488 select NEED_RET_TO_USER
490 Support for Intel's IOP13XX (XScale) family of processors.
496 select NEED_MACH_GPIO_H
497 select NEED_RET_TO_USER
500 select ARCH_REQUIRE_GPIOLIB
502 Support for Intel's 80219 and IOP32X (XScale) family of
509 select NEED_MACH_GPIO_H
510 select NEED_RET_TO_USER
513 select ARCH_REQUIRE_GPIOLIB
515 Support for Intel's IOP33X (XScale) family of processors.
520 select ARCH_HAS_DMA_SET_COHERENT_MASK
523 select ARCH_REQUIRE_GPIOLIB
524 select GENERIC_CLOCKEVENTS
525 select MIGHT_HAVE_PCI
526 select NEED_MACH_IO_H
527 select DMABOUNCE if PCI
529 Support for Intel's IXP4XX (XScale) family of processors.
534 select ARCH_REQUIRE_GPIOLIB
535 select GENERIC_CLOCKEVENTS
536 select MIGHT_HAVE_PCI
537 select PLAT_ORION_LEGACY
538 select USB_ARCH_HAS_EHCI
540 Support for the Marvell Dove SoC 88AP510
543 bool "Marvell Kirkwood"
546 select ARCH_REQUIRE_GPIOLIB
547 select GENERIC_CLOCKEVENTS
548 select PLAT_ORION_LEGACY
550 Support for the following Marvell Kirkwood series SoCs:
551 88F6180, 88F6192 and 88F6281.
557 select ARCH_REQUIRE_GPIOLIB
560 select USB_ARCH_HAS_OHCI
562 select GENERIC_CLOCKEVENTS
566 Support for the NXP LPC32XX family of processors
569 bool "Marvell MV78xx0"
572 select ARCH_REQUIRE_GPIOLIB
573 select GENERIC_CLOCKEVENTS
574 select PLAT_ORION_LEGACY
576 Support for the following Marvell MV78xx0 series SoCs:
584 select ARCH_REQUIRE_GPIOLIB
585 select GENERIC_CLOCKEVENTS
586 select PLAT_ORION_LEGACY
588 Support for the following Marvell Orion 5x series SoCs:
589 Orion-1 (5181), Orion-VoIP (5181L), Orion-NAS (5182),
590 Orion-2 (5281), Orion-1-90 (6183).
593 bool "Marvell PXA168/910/MMP2"
595 select ARCH_REQUIRE_GPIOLIB
597 select GENERIC_CLOCKEVENTS
602 select GENERIC_ALLOCATOR
603 select NEED_MACH_GPIO_H
605 Support for Marvell's PXA168/PXA910(MMP) and MMP2 processor line.
608 bool "Micrel/Kendin KS8695"
610 select ARCH_REQUIRE_GPIOLIB
611 select NEED_MACH_MEMORY_H
613 select GENERIC_CLOCKEVENTS
615 Support for Micrel/Kendin KS8695 "Centaur" (ARM922T) based
616 System-on-Chip devices.
619 bool "Nuvoton W90X900 CPU"
621 select ARCH_REQUIRE_GPIOLIB
624 select GENERIC_CLOCKEVENTS
626 Support for Nuvoton (Winbond logic dept.) ARM9 processor,
627 At present, the w90x900 has been renamed nuc900, regarding
628 the ARM series product line, you can login the following
629 link address to know more.
631 <http://www.nuvoton.com/hq/enu/ProductAndSales/ProductLines/
632 ConsumerElectronicsIC/ARMMicrocontroller/ARMMicrocontroller>
638 select GENERIC_CLOCKEVENTS
642 select MIGHT_HAVE_CACHE_L2X0
643 select ARCH_HAS_CPUFREQ
647 This enables support for NVIDIA Tegra based systems (Tegra APX,
648 Tegra 6xx and Tegra 2 series).
651 bool "PXA2xx/PXA3xx-based"
654 select ARCH_HAS_CPUFREQ
657 select ARCH_REQUIRE_GPIOLIB
658 select GENERIC_CLOCKEVENTS
663 select MULTI_IRQ_HANDLER
664 select ARM_CPU_SUSPEND if PM
666 select NEED_MACH_GPIO_H
668 Support for Intel/Marvell's PXA2xx/PXA3xx processor line.
673 select GENERIC_CLOCKEVENTS
674 select ARCH_REQUIRE_GPIOLIB
677 Support for Qualcomm MSM/QSD based systems. This runs on the
678 apps processor of the MSM/QSD and depends on a shared memory
679 interface to the modem processor which runs the baseband
680 stack and controls some vital subsystems
681 (clock and power control, etc).
684 bool "Renesas SH-Mobile / R-Mobile"
687 select HAVE_MACH_CLKDEV
689 select GENERIC_CLOCKEVENTS
690 select MIGHT_HAVE_CACHE_L2X0
693 select MULTI_IRQ_HANDLER
694 select PM_GENERIC_DOMAINS if PM
695 select NEED_MACH_MEMORY_H
697 Support for Renesas's SH-Mobile and R-Mobile ARM platforms.
703 select ARCH_MAY_HAVE_PC_FDC
704 select HAVE_PATA_PLATFORM
707 select ARCH_SPARSEMEM_ENABLE
708 select ARCH_USES_GETTIMEOFFSET
710 select NEED_MACH_IO_H
711 select NEED_MACH_MEMORY_H
713 On the Acorn Risc-PC, Linux can support the internal IDE disk and
714 CD-ROM interface, serial and parallel port, and the floppy drive.
721 select ARCH_SPARSEMEM_ENABLE
723 select ARCH_HAS_CPUFREQ
725 select GENERIC_CLOCKEVENTS
727 select ARCH_REQUIRE_GPIOLIB
729 select NEED_MACH_GPIO_H
730 select NEED_MACH_MEMORY_H
733 Support for StrongARM 11x0 based boards.
736 bool "Samsung S3C24XX SoCs"
738 select ARCH_HAS_CPUFREQ
741 select ARCH_USES_GETTIMEOFFSET
742 select HAVE_S3C2410_I2C if I2C
743 select HAVE_S3C_RTC if RTC_CLASS
744 select HAVE_S3C2410_WATCHDOG if WATCHDOG
745 select NEED_MACH_GPIO_H
746 select NEED_MACH_IO_H
748 Samsung S3C2410, S3C2412, S3C2413, S3C2416, S3C2440, S3C2442, S3C2443
749 and S3C2450 SoCs based systems, such as the Simtec Electronics BAST
750 (<http://www.simtec.co.uk/products/EB110ITX/>), the IPAQ 1940 or the
751 Samsung SMDK2410 development board (and derivatives).
754 bool "Samsung S3C64XX"
762 select ARCH_USES_GETTIMEOFFSET
763 select ARCH_HAS_CPUFREQ
764 select ARCH_REQUIRE_GPIOLIB
765 select SAMSUNG_CLKSRC
766 select SAMSUNG_IRQ_VIC_TIMER
767 select S3C_GPIO_TRACK
769 select USB_ARCH_HAS_OHCI
770 select SAMSUNG_GPIOLIB_4BIT
771 select HAVE_S3C2410_I2C if I2C
772 select HAVE_S3C2410_WATCHDOG if WATCHDOG
773 select NEED_MACH_GPIO_H
775 Samsung S3C64XX series based systems
778 bool "Samsung S5P6440 S5P6450"
784 select HAVE_S3C2410_WATCHDOG if WATCHDOG
785 select GENERIC_CLOCKEVENTS
786 select HAVE_S3C2410_I2C if I2C
787 select HAVE_S3C_RTC if RTC_CLASS
788 select NEED_MACH_GPIO_H
790 Samsung S5P64X0 CPU based systems, such as the Samsung SMDK6440,
794 bool "Samsung S5PC100"
799 select ARCH_USES_GETTIMEOFFSET
800 select HAVE_S3C2410_I2C if I2C
801 select HAVE_S3C_RTC if RTC_CLASS
802 select HAVE_S3C2410_WATCHDOG if WATCHDOG
803 select NEED_MACH_GPIO_H
805 Samsung S5PC100 series based systems
808 bool "Samsung S5PV210/S5PC110"
810 select ARCH_SPARSEMEM_ENABLE
811 select ARCH_HAS_HOLES_MEMORYMODEL
816 select ARCH_HAS_CPUFREQ
817 select GENERIC_CLOCKEVENTS
818 select HAVE_S3C2410_I2C if I2C
819 select HAVE_S3C_RTC if RTC_CLASS
820 select HAVE_S3C2410_WATCHDOG if WATCHDOG
821 select NEED_MACH_GPIO_H
822 select NEED_MACH_MEMORY_H
824 Samsung S5PV210/S5PC110 series based systems
827 bool "SAMSUNG EXYNOS"
829 select ARCH_SPARSEMEM_ENABLE
830 select ARCH_HAS_HOLES_MEMORYMODEL
834 select ARCH_HAS_CPUFREQ
835 select GENERIC_CLOCKEVENTS
836 select HAVE_S3C_RTC if RTC_CLASS
837 select HAVE_S3C2410_I2C if I2C
838 select HAVE_S3C2410_WATCHDOG if WATCHDOG
839 select NEED_MACH_GPIO_H
840 select NEED_MACH_MEMORY_H
842 Support for SAMSUNG's EXYNOS SoCs (EXYNOS4/5)
851 select ARCH_USES_GETTIMEOFFSET
852 select NEED_MACH_MEMORY_H
854 Support for the StrongARM based Digital DNARD machine, also known
855 as "Shark" (<http://www.shark-linux.de/shark.html>).
858 bool "ST-Ericsson U300 Series"
864 select ARM_PATCH_PHYS_VIRT
866 select GENERIC_CLOCKEVENTS
870 select ARCH_REQUIRE_GPIOLIB
873 Support for ST-Ericsson U300 series mobile platforms.
876 bool "ST-Ericsson U8500 Series"
880 select GENERIC_CLOCKEVENTS
882 select ARCH_REQUIRE_GPIOLIB
883 select ARCH_HAS_CPUFREQ
885 select MIGHT_HAVE_CACHE_L2X0
887 Support for ST-Ericsson's Ux500 architecture
890 bool "STMicroelectronics Nomadik"
895 select GENERIC_CLOCKEVENTS
897 select PINCTRL_STN8815
898 select MIGHT_HAVE_CACHE_L2X0
899 select ARCH_REQUIRE_GPIOLIB
901 Support for the Nomadik platform by ST-Ericsson
905 select GENERIC_CLOCKEVENTS
906 select ARCH_REQUIRE_GPIOLIB
910 select GENERIC_ALLOCATOR
911 select GENERIC_IRQ_CHIP
912 select ARCH_HAS_HOLES_MEMORYMODEL
913 select NEED_MACH_GPIO_H
915 Support for TI's DaVinci platform.
921 select ARCH_REQUIRE_GPIOLIB
922 select ARCH_HAS_CPUFREQ
924 select GENERIC_CLOCKEVENTS
925 select ARCH_HAS_HOLES_MEMORYMODEL
926 select NEED_MACH_GPIO_H
928 Support for TI's OMAP platform (OMAP1/2/3/4).
933 select ARCH_REQUIRE_GPIOLIB
937 select GENERIC_CLOCKEVENTS
940 Support for ST's SPEAr platform (SPEAr3xx, SPEAr6xx and SPEAr13xx).
943 bool "VIA/WonderMedia 85xx"
946 select ARCH_HAS_CPUFREQ
947 select GENERIC_CLOCKEVENTS
948 select ARCH_REQUIRE_GPIOLIB
954 Support for VIA/WonderMedia VT8500/WM85xx System-on-Chip.
957 bool "Xilinx Zynq ARM Cortex A9 Platform"
959 select GENERIC_CLOCKEVENTS
964 select MIGHT_HAVE_CACHE_L2X0
967 Support for Xilinx Zynq ARM Cortex A9 Platform
970 menu "Multiple platform selection"
971 depends on ARCH_MULTIPLATFORM
973 comment "CPU Core family selection"
976 bool "ARMv4 based platforms (FA526, StrongARM)"
977 select ARCH_MULTI_V4_V5
978 depends on !ARCH_MULTI_V6_V7
980 config ARCH_MULTI_V4T
981 bool "ARMv4T based platforms (ARM720T, ARM920T, ...)"
982 select ARCH_MULTI_V4_V5
983 depends on !ARCH_MULTI_V6_V7
986 bool "ARMv5 based platforms (ARM926T, XSCALE, PJ1, ...)"
987 select ARCH_MULTI_V4_V5
988 depends on !ARCH_MULTI_V6_V7
990 config ARCH_MULTI_V4_V5
994 bool "ARMv6 based platforms (ARM11, Scorpion, ...)"
996 select ARCH_MULTI_V6_V7
999 bool "ARMv7 based platforms (Cortex-A, PJ4, Krait)"
1001 select ARCH_VEXPRESS
1003 select ARCH_MULTI_V6_V7
1005 config ARCH_MULTI_V6_V7
1008 config ARCH_MULTI_CPU_AUTO
1009 def_bool !(ARCH_MULTI_V4 || ARCH_MULTI_V4T || ARCH_MULTI_V6_V7)
1010 select ARCH_MULTI_V5
1015 # This is sorted alphabetically by mach-* pathname. However, plat-*
1016 # Kconfigs may be included either alphabetically (according to the
1017 # plat- suffix) or along side the corresponding mach-* source.
1019 source "arch/arm/mach-mvebu/Kconfig"
1021 source "arch/arm/mach-at91/Kconfig"
1023 source "arch/arm/mach-clps711x/Kconfig"
1025 source "arch/arm/mach-cns3xxx/Kconfig"
1027 source "arch/arm/mach-davinci/Kconfig"
1029 source "arch/arm/mach-dove/Kconfig"
1031 source "arch/arm/mach-ep93xx/Kconfig"
1033 source "arch/arm/mach-footbridge/Kconfig"
1035 source "arch/arm/mach-gemini/Kconfig"
1037 source "arch/arm/mach-h720x/Kconfig"
1039 source "arch/arm/mach-highbank/Kconfig"
1041 source "arch/arm/mach-integrator/Kconfig"
1043 source "arch/arm/mach-iop32x/Kconfig"
1045 source "arch/arm/mach-iop33x/Kconfig"
1047 source "arch/arm/mach-iop13xx/Kconfig"
1049 source "arch/arm/mach-ixp4xx/Kconfig"
1051 source "arch/arm/mach-kirkwood/Kconfig"
1053 source "arch/arm/mach-ks8695/Kconfig"
1055 source "arch/arm/mach-msm/Kconfig"
1057 source "arch/arm/mach-mv78xx0/Kconfig"
1059 source "arch/arm/plat-mxc/Kconfig"
1061 source "arch/arm/mach-mxs/Kconfig"
1063 source "arch/arm/mach-netx/Kconfig"
1065 source "arch/arm/mach-nomadik/Kconfig"
1066 source "arch/arm/plat-nomadik/Kconfig"
1068 source "arch/arm/plat-omap/Kconfig"
1070 source "arch/arm/mach-omap1/Kconfig"
1072 source "arch/arm/mach-omap2/Kconfig"
1074 source "arch/arm/mach-orion5x/Kconfig"
1076 source "arch/arm/mach-picoxcell/Kconfig"
1078 source "arch/arm/mach-pxa/Kconfig"
1079 source "arch/arm/plat-pxa/Kconfig"
1081 source "arch/arm/mach-mmp/Kconfig"
1083 source "arch/arm/mach-realview/Kconfig"
1085 source "arch/arm/mach-sa1100/Kconfig"
1087 source "arch/arm/plat-samsung/Kconfig"
1088 source "arch/arm/plat-s3c24xx/Kconfig"
1090 source "arch/arm/mach-socfpga/Kconfig"
1092 source "arch/arm/plat-spear/Kconfig"
1094 source "arch/arm/mach-s3c24xx/Kconfig"
1096 source "arch/arm/mach-s3c2412/Kconfig"
1097 source "arch/arm/mach-s3c2440/Kconfig"
1101 source "arch/arm/mach-s3c64xx/Kconfig"
1104 source "arch/arm/mach-s5p64x0/Kconfig"
1106 source "arch/arm/mach-s5pc100/Kconfig"
1108 source "arch/arm/mach-s5pv210/Kconfig"
1110 source "arch/arm/mach-exynos/Kconfig"
1112 source "arch/arm/mach-shmobile/Kconfig"
1114 source "arch/arm/mach-prima2/Kconfig"
1116 source "arch/arm/mach-tegra/Kconfig"
1118 source "arch/arm/mach-u300/Kconfig"
1120 source "arch/arm/mach-ux500/Kconfig"
1122 source "arch/arm/mach-versatile/Kconfig"
1124 source "arch/arm/mach-vexpress/Kconfig"
1125 source "arch/arm/plat-versatile/Kconfig"
1127 source "arch/arm/mach-w90x900/Kconfig"
1129 # Definitions to make life easier
1135 select GENERIC_CLOCKEVENTS
1140 select GENERIC_IRQ_CHIP
1144 config PLAT_ORION_LEGACY
1151 config PLAT_VERSATILE
1154 config ARM_TIMER_SP804
1157 select HAVE_SCHED_CLOCK
1159 source arch/arm/mm/Kconfig
1163 default 16 if ARCH_EP93XX
1167 bool "Enable iWMMXt support"
1168 depends on CPU_XSCALE || CPU_XSC3 || CPU_MOHAWK || CPU_PJ4
1169 default y if PXA27x || PXA3xx || PXA95x || ARCH_MMP
1171 Enable support for iWMMXt context switching at run time if
1172 running on a CPU that supports it.
1176 depends on CPU_XSCALE
1179 config MULTI_IRQ_HANDLER
1182 Allow each machine to specify it's own IRQ handler at run time.
1185 source "arch/arm/Kconfig-nommu"
1188 config ARM_ERRATA_326103
1189 bool "ARM errata: FSR write bit incorrect on a SWP to read-only memory"
1192 Executing a SWP instruction to read-only memory does not set bit 11
1193 of the FSR on the ARM 1136 prior to r1p0. This causes the kernel to
1194 treat the access as a read, preventing a COW from occurring and
1195 causing the faulting task to livelock.
1197 config ARM_ERRATA_411920
1198 bool "ARM errata: Invalidation of the Instruction Cache operation can fail"
1199 depends on CPU_V6 || CPU_V6K
1201 Invalidation of the Instruction Cache operation can
1202 fail. This erratum is present in 1136 (before r1p4), 1156 and 1176.
1203 It does not affect the MPCore. This option enables the ARM Ltd.
1204 recommended workaround.
1206 config ARM_ERRATA_430973
1207 bool "ARM errata: Stale prediction on replaced interworking branch"
1210 This option enables the workaround for the 430973 Cortex-A8
1211 (r1p0..r1p2) erratum. If a code sequence containing an ARM/Thumb
1212 interworking branch is replaced with another code sequence at the
1213 same virtual address, whether due to self-modifying code or virtual
1214 to physical address re-mapping, Cortex-A8 does not recover from the
1215 stale interworking branch prediction. This results in Cortex-A8
1216 executing the new code sequence in the incorrect ARM or Thumb state.
1217 The workaround enables the BTB/BTAC operations by setting ACTLR.IBE
1218 and also flushes the branch target cache at every context switch.
1219 Note that setting specific bits in the ACTLR register may not be
1220 available in non-secure mode.
1222 config ARM_ERRATA_458693
1223 bool "ARM errata: Processor deadlock when a false hazard is created"
1226 This option enables the workaround for the 458693 Cortex-A8 (r2p0)
1227 erratum. For very specific sequences of memory operations, it is
1228 possible for a hazard condition intended for a cache line to instead
1229 be incorrectly associated with a different cache line. This false
1230 hazard might then cause a processor deadlock. The workaround enables
1231 the L1 caching of the NEON accesses and disables the PLD instruction
1232 in the ACTLR register. Note that setting specific bits in the ACTLR
1233 register may not be available in non-secure mode.
1235 config ARM_ERRATA_460075
1236 bool "ARM errata: Data written to the L2 cache can be overwritten with stale data"
1239 This option enables the workaround for the 460075 Cortex-A8 (r2p0)
1240 erratum. Any asynchronous access to the L2 cache may encounter a
1241 situation in which recent store transactions to the L2 cache are lost
1242 and overwritten with stale memory contents from external memory. The
1243 workaround disables the write-allocate mode for the L2 cache via the
1244 ACTLR register. Note that setting specific bits in the ACTLR register
1245 may not be available in non-secure mode.
1247 config ARM_ERRATA_742230
1248 bool "ARM errata: DMB operation may be faulty"
1249 depends on CPU_V7 && SMP
1251 This option enables the workaround for the 742230 Cortex-A9
1252 (r1p0..r2p2) erratum. Under rare circumstances, a DMB instruction
1253 between two write operations may not ensure the correct visibility
1254 ordering of the two writes. This workaround sets a specific bit in
1255 the diagnostic register of the Cortex-A9 which causes the DMB
1256 instruction to behave as a DSB, ensuring the correct behaviour of
1259 config ARM_ERRATA_742231
1260 bool "ARM errata: Incorrect hazard handling in the SCU may lead to data corruption"
1261 depends on CPU_V7 && SMP
1263 This option enables the workaround for the 742231 Cortex-A9
1264 (r2p0..r2p2) erratum. Under certain conditions, specific to the
1265 Cortex-A9 MPCore micro-architecture, two CPUs working in SMP mode,
1266 accessing some data located in the same cache line, may get corrupted
1267 data due to bad handling of the address hazard when the line gets
1268 replaced from one of the CPUs at the same time as another CPU is
1269 accessing it. This workaround sets specific bits in the diagnostic
1270 register of the Cortex-A9 which reduces the linefill issuing
1271 capabilities of the processor.
1273 config PL310_ERRATA_588369
1274 bool "PL310 errata: Clean & Invalidate maintenance operations do not invalidate clean lines"
1275 depends on CACHE_L2X0
1277 The PL310 L2 cache controller implements three types of Clean &
1278 Invalidate maintenance operations: by Physical Address
1279 (offset 0x7F0), by Index/Way (0x7F8) and by Way (0x7FC).
1280 They are architecturally defined to behave as the execution of a
1281 clean operation followed immediately by an invalidate operation,
1282 both performing to the same memory location. This functionality
1283 is not correctly implemented in PL310 as clean lines are not
1284 invalidated as a result of these operations.
1286 config ARM_ERRATA_720789
1287 bool "ARM errata: TLBIASIDIS and TLBIMVAIS operations can broadcast a faulty ASID"
1290 This option enables the workaround for the 720789 Cortex-A9 (prior to
1291 r2p0) erratum. A faulty ASID can be sent to the other CPUs for the
1292 broadcasted CP15 TLB maintenance operations TLBIASIDIS and TLBIMVAIS.
1293 As a consequence of this erratum, some TLB entries which should be
1294 invalidated are not, resulting in an incoherency in the system page
1295 tables. The workaround changes the TLB flushing routines to invalidate
1296 entries regardless of the ASID.
1298 config PL310_ERRATA_727915
1299 bool "PL310 errata: Background Clean & Invalidate by Way operation can cause data corruption"
1300 depends on CACHE_L2X0
1302 PL310 implements the Clean & Invalidate by Way L2 cache maintenance
1303 operation (offset 0x7FC). This operation runs in background so that
1304 PL310 can handle normal accesses while it is in progress. Under very
1305 rare circumstances, due to this erratum, write data can be lost when
1306 PL310 treats a cacheable write transaction during a Clean &
1307 Invalidate by Way operation.
1309 config ARM_ERRATA_743622
1310 bool "ARM errata: Faulty hazard checking in the Store Buffer may lead to data corruption"
1313 This option enables the workaround for the 743622 Cortex-A9
1314 (r2p*) erratum. Under very rare conditions, a faulty
1315 optimisation in the Cortex-A9 Store Buffer may lead to data
1316 corruption. This workaround sets a specific bit in the diagnostic
1317 register of the Cortex-A9 which disables the Store Buffer
1318 optimisation, preventing the defect from occurring. This has no
1319 visible impact on the overall performance or power consumption of the
1322 config ARM_ERRATA_751472
1323 bool "ARM errata: Interrupted ICIALLUIS may prevent completion of broadcasted operation"
1326 This option enables the workaround for the 751472 Cortex-A9 (prior
1327 to r3p0) erratum. An interrupted ICIALLUIS operation may prevent the
1328 completion of a following broadcasted operation if the second
1329 operation is received by a CPU before the ICIALLUIS has completed,
1330 potentially leading to corrupted entries in the cache or TLB.
1332 config PL310_ERRATA_753970
1333 bool "PL310 errata: cache sync operation may be faulty"
1334 depends on CACHE_PL310
1336 This option enables the workaround for the 753970 PL310 (r3p0) erratum.
1338 Under some condition the effect of cache sync operation on
1339 the store buffer still remains when the operation completes.
1340 This means that the store buffer is always asked to drain and
1341 this prevents it from merging any further writes. The workaround
1342 is to replace the normal offset of cache sync operation (0x730)
1343 by another offset targeting an unmapped PL310 register 0x740.
1344 This has the same effect as the cache sync operation: store buffer
1345 drain and waiting for all buffers empty.
1347 config ARM_ERRATA_754322
1348 bool "ARM errata: possible faulty MMU translations following an ASID switch"
1351 This option enables the workaround for the 754322 Cortex-A9 (r2p*,
1352 r3p*) erratum. A speculative memory access may cause a page table walk
1353 which starts prior to an ASID switch but completes afterwards. This
1354 can populate the micro-TLB with a stale entry which may be hit with
1355 the new ASID. This workaround places two dsb instructions in the mm
1356 switching code so that no page table walks can cross the ASID switch.
1358 config ARM_ERRATA_754327
1359 bool "ARM errata: no automatic Store Buffer drain"
1360 depends on CPU_V7 && SMP
1362 This option enables the workaround for the 754327 Cortex-A9 (prior to
1363 r2p0) erratum. The Store Buffer does not have any automatic draining
1364 mechanism and therefore a livelock may occur if an external agent
1365 continuously polls a memory location waiting to observe an update.
1366 This workaround defines cpu_relax() as smp_mb(), preventing correctly
1367 written polling loops from denying visibility of updates to memory.
1369 config ARM_ERRATA_364296
1370 bool "ARM errata: Possible cache data corruption with hit-under-miss enabled"
1371 depends on CPU_V6 && !SMP
1373 This options enables the workaround for the 364296 ARM1136
1374 r0p2 erratum (possible cache data corruption with
1375 hit-under-miss enabled). It sets the undocumented bit 31 in
1376 the auxiliary control register and the FI bit in the control
1377 register, thus disabling hit-under-miss without putting the
1378 processor into full low interrupt latency mode. ARM11MPCore
1381 config ARM_ERRATA_764369
1382 bool "ARM errata: Data cache line maintenance operation by MVA may not succeed"
1383 depends on CPU_V7 && SMP
1385 This option enables the workaround for erratum 764369
1386 affecting Cortex-A9 MPCore with two or more processors (all
1387 current revisions). Under certain timing circumstances, a data
1388 cache line maintenance operation by MVA targeting an Inner
1389 Shareable memory region may fail to proceed up to either the
1390 Point of Coherency or to the Point of Unification of the
1391 system. This workaround adds a DSB instruction before the
1392 relevant cache maintenance functions and sets a specific bit
1393 in the diagnostic control register of the SCU.
1395 config PL310_ERRATA_769419
1396 bool "PL310 errata: no automatic Store Buffer drain"
1397 depends on CACHE_L2X0
1399 On revisions of the PL310 prior to r3p2, the Store Buffer does
1400 not automatically drain. This can cause normal, non-cacheable
1401 writes to be retained when the memory system is idle, leading
1402 to suboptimal I/O performance for drivers using coherent DMA.
1403 This option adds a write barrier to the cpu_idle loop so that,
1404 on systems with an outer cache, the store buffer is drained
1407 config ARM_ERRATA_775420
1408 bool "ARM errata: A data cache maintenance operation which aborts, might lead to deadlock"
1411 This option enables the workaround for the 775420 Cortex-A9 (r2p2,
1412 r2p6,r2p8,r2p10,r3p0) erratum. In case a date cache maintenance
1413 operation aborts with MMU exception, it might cause the processor
1414 to deadlock. This workaround puts DSB before executing ISB if
1415 an abort may occur on cache maintenance.
1417 config ARM_ERRATA_782773
1418 bool "ARM errata: Updating a translation entry might cause an unexpected translation fault"
1421 This option enables the workaround for the 782773 Cortex-A9 (all r0,
1422 r2 and r3 revisions) erratum. It might cause MMU exception in case
1423 page table walk happens just after updating the existing
1424 with setting page table in L1 data cache.
1428 source "arch/arm/common/Kconfig"
1438 Find out whether you have ISA slots on your motherboard. ISA is the
1439 name of a bus system, i.e. the way the CPU talks to the other stuff
1440 inside your box. Other bus systems are PCI, EISA, MicroChannel
1441 (MCA) or VESA. ISA is an older system, now being displaced by PCI;
1442 newer boards don't support it. If you have ISA, say Y, otherwise N.
1444 # Select ISA DMA controller support
1449 # Select ISA DMA interface
1454 bool "PCI support" if MIGHT_HAVE_PCI
1456 Find out whether you have a PCI motherboard. PCI is the name of a
1457 bus system, i.e. the way the CPU talks to the other stuff inside
1458 your box. Other bus systems are ISA, EISA, MicroChannel (MCA) or
1459 VESA. If you have PCI, say Y, otherwise N.
1465 config PCI_NANOENGINE
1466 bool "BSE nanoEngine PCI support"
1467 depends on SA1100_NANOENGINE
1469 Enable PCI on the BSE nanoEngine board.
1474 # Select the host bridge type
1475 config PCI_HOST_VIA82C505
1477 depends on PCI && ARCH_SHARK
1480 config PCI_HOST_ITE8152
1482 depends on PCI && MACH_ARMCORE
1486 source "drivers/pci/Kconfig"
1488 source "drivers/pcmcia/Kconfig"
1492 menu "Kernel Features"
1497 This option should be selected by machines which have an SMP-
1500 The only effect of this option is to make the SMP-related
1501 options available to the user for configuration.
1504 bool "Symmetric Multi-Processing"
1505 depends on CPU_V6K || CPU_V7
1506 depends on GENERIC_CLOCKEVENTS
1509 select USE_GENERIC_SMP_HELPERS
1510 select HAVE_ARM_SCU if !ARCH_MSM_SCORPIONMP
1512 This enables support for systems with more than one CPU. If you have
1513 a system with only one CPU, like most personal computers, say N. If
1514 you have a system with more than one CPU, say Y.
1516 If you say N here, the kernel will run on single and multiprocessor
1517 machines, but will use only one CPU of a multiprocessor machine. If
1518 you say Y here, the kernel will run on many, but not all, single
1519 processor machines. On a single processor machine, the kernel will
1520 run faster if you say N here.
1522 See also <file:Documentation/x86/i386/IO-APIC.txt>,
1523 <file:Documentation/nmi_watchdog.txt> and the SMP-HOWTO available at
1524 <http://tldp.org/HOWTO/SMP-HOWTO.html>.
1526 If you don't know what to do here, say N.
1529 bool "Allow booting SMP kernel on uniprocessor systems (EXPERIMENTAL)"
1530 depends on EXPERIMENTAL
1531 depends on SMP && !XIP_KERNEL
1534 SMP kernels contain instructions which fail on non-SMP processors.
1535 Enabling this option allows the kernel to modify itself to make
1536 these instructions safe. Disabling it allows about 1K of space
1539 If you don't know what to do here, say Y.
1541 config ARM_CPU_TOPOLOGY
1542 bool "Support cpu topology definition"
1543 depends on SMP && CPU_V7
1546 Support ARM cpu topology definition. The MPIDR register defines
1547 affinity between processors which is then used to describe the cpu
1548 topology of an ARM System.
1551 bool "Multi-core scheduler support"
1552 depends on ARM_CPU_TOPOLOGY
1554 Multi-core scheduler support improves the CPU scheduler's decision
1555 making when dealing with multi-core CPU chips at a cost of slightly
1556 increased overhead in some places. If unsure say N here.
1559 bool "SMT scheduler support"
1560 depends on ARM_CPU_TOPOLOGY
1562 Improves the CPU scheduler's decision making when dealing with
1563 MultiThreading at a cost of slightly increased overhead in some
1564 places. If unsure say N here.
1569 This option enables support for the ARM system coherency unit
1571 config ARM_ARCH_TIMER
1572 bool "Architected timer support"
1575 This option enables support for the ARM architected timer
1581 This options enables support for the ARM timer and watchdog unit
1584 prompt "Memory split"
1587 Select the desired split between kernel and user memory.
1589 If you are not absolutely sure what you are doing, leave this
1593 bool "3G/1G user/kernel split"
1595 bool "2G/2G user/kernel split"
1597 bool "1G/3G user/kernel split"
1602 default 0x40000000 if VMSPLIT_1G
1603 default 0x80000000 if VMSPLIT_2G
1607 int "Maximum number of CPUs (2-32)"
1613 bool "Support for hot-pluggable CPUs (EXPERIMENTAL)"
1614 depends on SMP && HOTPLUG && EXPERIMENTAL
1616 Say Y here to experiment with turning CPUs off and on. CPUs
1617 can be controlled through /sys/devices/system/cpu.
1620 bool "Use local timer interrupts"
1623 select HAVE_ARM_TWD if (!ARCH_MSM_SCORPIONMP && !EXYNOS4_MCT)
1625 Enable support for local timers on SMP platforms, rather then the
1626 legacy IPI broadcast method. Local timers allows the system
1627 accounting to be spread across the timer interval, preventing a
1628 "thundering herd" at every timer tick.
1632 default 1024 if ARCH_SHMOBILE || ARCH_TEGRA
1633 default 355 if ARCH_U8500
1634 default 264 if MACH_H4700
1635 default 512 if SOC_OMAP5
1636 default 288 if ARCH_VT8500
1639 Maximum number of GPIOs in the system.
1641 If unsure, leave the default value.
1643 source kernel/Kconfig.preempt
1647 default 200 if ARCH_EBSA110 || ARCH_S3C24XX || ARCH_S5P64X0 || \
1648 ARCH_S5PV210 || ARCH_EXYNOS4
1649 default OMAP_32K_TIMER_HZ if ARCH_OMAP && OMAP_32K_TIMER
1650 default AT91_TIMER_HZ if ARCH_AT91
1651 default SHMOBILE_TIMER_HZ if ARCH_SHMOBILE
1654 config THUMB2_KERNEL
1655 bool "Compile the kernel in Thumb-2 mode (EXPERIMENTAL)"
1656 depends on CPU_V7 && !CPU_V6 && !CPU_V6K && EXPERIMENTAL
1658 select ARM_ASM_UNIFIED
1661 By enabling this option, the kernel will be compiled in
1662 Thumb-2 mode. A compiler/assembler that understand the unified
1663 ARM-Thumb syntax is needed.
1667 config THUMB2_AVOID_R_ARM_THM_JUMP11
1668 bool "Work around buggy Thumb-2 short branch relocations in gas"
1669 depends on THUMB2_KERNEL && MODULES
1672 Various binutils versions can resolve Thumb-2 branches to
1673 locally-defined, preemptible global symbols as short-range "b.n"
1674 branch instructions.
1676 This is a problem, because there's no guarantee the final
1677 destination of the symbol, or any candidate locations for a
1678 trampoline, are within range of the branch. For this reason, the
1679 kernel does not support fixing up the R_ARM_THM_JUMP11 (102)
1680 relocation in modules at all, and it makes little sense to add
1683 The symptom is that the kernel fails with an "unsupported
1684 relocation" error when loading some modules.
1686 Until fixed tools are available, passing
1687 -fno-optimize-sibling-calls to gcc should prevent gcc generating
1688 code which hits this problem, at the cost of a bit of extra runtime
1689 stack usage in some cases.
1691 The problem is described in more detail at:
1692 https://bugs.launchpad.net/binutils-linaro/+bug/725126
1694 Only Thumb-2 kernels are affected.
1696 Unless you are sure your tools don't have this problem, say Y.
1698 config ARM_ASM_UNIFIED
1702 bool "Use the ARM EABI to compile the kernel"
1704 This option allows for the kernel to be compiled using the latest
1705 ARM ABI (aka EABI). This is only useful if you are using a user
1706 space environment that is also compiled with EABI.
1708 Since there are major incompatibilities between the legacy ABI and
1709 EABI, especially with regard to structure member alignment, this
1710 option also changes the kernel syscall calling convention to
1711 disambiguate both ABIs and allow for backward compatibility support
1712 (selected with CONFIG_OABI_COMPAT).
1714 To use this you need GCC version 4.0.0 or later.
1717 bool "Allow old ABI binaries to run with this kernel (EXPERIMENTAL)"
1718 depends on AEABI && EXPERIMENTAL && !THUMB2_KERNEL
1721 This option preserves the old syscall interface along with the
1722 new (ARM EABI) one. It also provides a compatibility layer to
1723 intercept syscalls that have structure arguments which layout
1724 in memory differs between the legacy ABI and the new ARM EABI
1725 (only for non "thumb" binaries). This option adds a tiny
1726 overhead to all syscalls and produces a slightly larger kernel.
1727 If you know you'll be using only pure EABI user space then you
1728 can say N here. If this option is not selected and you attempt
1729 to execute a legacy ABI binary then the result will be
1730 UNPREDICTABLE (in fact it can be predicted that it won't work
1731 at all). If in doubt say Y.
1733 config ARCH_HAS_HOLES_MEMORYMODEL
1736 config ARCH_SPARSEMEM_ENABLE
1739 config ARCH_SPARSEMEM_DEFAULT
1740 def_bool ARCH_SPARSEMEM_ENABLE
1742 config ARCH_SELECT_MEMORY_MODEL
1743 def_bool ARCH_SPARSEMEM_ENABLE
1745 config HAVE_ARCH_PFN_VALID
1746 def_bool ARCH_HAS_HOLES_MEMORYMODEL || !SPARSEMEM
1749 bool "High Memory Support"
1752 The address space of ARM processors is only 4 Gigabytes large
1753 and it has to accommodate user address space, kernel address
1754 space as well as some memory mapped IO. That means that, if you
1755 have a large amount of physical memory and/or IO, not all of the
1756 memory can be "permanently mapped" by the kernel. The physical
1757 memory that is not permanently mapped is called "high memory".
1759 Depending on the selected kernel/user memory split, minimum
1760 vmalloc space and actual amount of RAM, you may not need this
1761 option which should result in a slightly faster kernel.
1766 bool "Allocate 2nd-level pagetables from highmem"
1769 config HW_PERF_EVENTS
1770 bool "Enable hardware performance counter support for perf events"
1771 depends on PERF_EVENTS
1774 Enable hardware performance counter support for perf events. If
1775 disabled, perf events will use software events only.
1779 config FORCE_MAX_ZONEORDER
1780 int "Maximum zone order" if ARCH_SHMOBILE
1781 range 11 64 if ARCH_SHMOBILE
1782 default "9" if SA1111
1785 The kernel memory allocator divides physically contiguous memory
1786 blocks into "zones", where each zone is a power of two number of
1787 pages. This option selects the largest power of two that the kernel
1788 keeps in the memory allocator. If you need to allocate very large
1789 blocks of physically contiguous memory, then you may need to
1790 increase this value.
1792 This config option is actually maximum order plus one. For example,
1793 a value of 11 means that the largest free memory block is 2^10 pages.
1795 config ALIGNMENT_TRAP
1797 depends on CPU_CP15_MMU
1798 default y if !ARCH_EBSA110
1799 select HAVE_PROC_CPU if PROC_FS
1801 ARM processors cannot fetch/store information which is not
1802 naturally aligned on the bus, i.e., a 4 byte fetch must start at an
1803 address divisible by 4. On 32-bit ARM processors, these non-aligned
1804 fetch/store instructions will be emulated in software if you say
1805 here, which has a severe performance impact. This is necessary for
1806 correct operation of some network protocols. With an IP-only
1807 configuration it is safe to say N, otherwise say Y.
1809 config UACCESS_WITH_MEMCPY
1810 bool "Use kernel mem{cpy,set}() for {copy_to,clear}_user()"
1812 default y if CPU_FEROCEON
1814 Implement faster copy_to_user and clear_user methods for CPU
1815 cores where a 8-word STM instruction give significantly higher
1816 memory write throughput than a sequence of individual 32bit stores.
1818 A possible side effect is a slight increase in scheduling latency
1819 between threads sharing the same address space if they invoke
1820 such copy operations with large buffers.
1822 However, if the CPU data cache is using a write-allocate mode,
1823 this option is unlikely to provide any performance gain.
1827 prompt "Enable seccomp to safely compute untrusted bytecode"
1829 This kernel feature is useful for number crunching applications
1830 that may need to compute untrusted bytecode during their
1831 execution. By using pipes or other transports made available to
1832 the process as file descriptors supporting the read/write
1833 syscalls, it's possible to isolate those applications in
1834 their own address space using seccomp. Once seccomp is
1835 enabled via prctl(PR_SET_SECCOMP), it cannot be disabled
1836 and the task is only allowed to execute a few safe syscalls
1837 defined by each seccomp mode.
1839 config CC_STACKPROTECTOR
1840 bool "Enable -fstack-protector buffer overflow detection (EXPERIMENTAL)"
1841 depends on EXPERIMENTAL
1843 This option turns on the -fstack-protector GCC feature. This
1844 feature puts, at the beginning of functions, a canary value on
1845 the stack just before the return address, and validates
1846 the value just before actually returning. Stack based buffer
1847 overflows (that need to overwrite this return address) now also
1848 overwrite the canary, which gets detected and the attack is then
1849 neutralized via a kernel panic.
1850 This feature requires gcc version 4.2 or above.
1857 bool "Xen guest support on ARM (EXPERIMENTAL)"
1858 depends on EXPERIMENTAL && ARM && OF
1860 Say Y if you want to run Linux in a Virtual Machine on Xen on ARM.
1867 bool "Flattened Device Tree support"
1869 select OF_EARLY_FLATTREE
1872 Include support for flattened device tree machine descriptions.
1875 bool "Support for the traditional ATAGS boot data passing" if USE_OF
1878 This is the traditional way of passing data to the kernel at boot
1879 time. If you are solely relying on the flattened device tree (or
1880 the ARM_ATAG_DTB_COMPAT option) then you may unselect this option
1881 to remove ATAGS support from your kernel binary. If unsure,
1884 config DEPRECATED_PARAM_STRUCT
1885 bool "Provide old way to pass kernel parameters"
1888 This was deprecated in 2001 and announced to live on for 5 years.
1889 Some old boot loaders still use this way.
1891 # Compressed boot loader in ROM. Yes, we really want to ask about
1892 # TEXT and BSS so we preserve their values in the config files.
1893 config ZBOOT_ROM_TEXT
1894 hex "Compressed ROM boot loader base address"
1897 The physical address at which the ROM-able zImage is to be
1898 placed in the target. Platforms which normally make use of
1899 ROM-able zImage formats normally set this to a suitable
1900 value in their defconfig file.
1902 If ZBOOT_ROM is not enabled, this has no effect.
1904 config ZBOOT_ROM_BSS
1905 hex "Compressed ROM boot loader BSS address"
1908 The base address of an area of read/write memory in the target
1909 for the ROM-able zImage which must be available while the
1910 decompressor is running. It must be large enough to hold the
1911 entire decompressed kernel plus an additional 128 KiB.
1912 Platforms which normally make use of ROM-able zImage formats
1913 normally set this to a suitable value in their defconfig file.
1915 If ZBOOT_ROM is not enabled, this has no effect.
1918 bool "Compressed boot loader in ROM/flash"
1919 depends on ZBOOT_ROM_TEXT != ZBOOT_ROM_BSS
1921 Say Y here if you intend to execute your compressed kernel image
1922 (zImage) directly from ROM or flash. If unsure, say N.
1925 prompt "Include SD/MMC loader in zImage (EXPERIMENTAL)"
1926 depends on ZBOOT_ROM && ARCH_SH7372 && EXPERIMENTAL
1927 default ZBOOT_ROM_NONE
1929 Include experimental SD/MMC loading code in the ROM-able zImage.
1930 With this enabled it is possible to write the ROM-able zImage
1931 kernel image to an MMC or SD card and boot the kernel straight
1932 from the reset vector. At reset the processor Mask ROM will load
1933 the first part of the ROM-able zImage which in turn loads the
1934 rest the kernel image to RAM.
1936 config ZBOOT_ROM_NONE
1937 bool "No SD/MMC loader in zImage (EXPERIMENTAL)"
1939 Do not load image from SD or MMC
1941 config ZBOOT_ROM_MMCIF
1942 bool "Include MMCIF loader in zImage (EXPERIMENTAL)"
1944 Load image from MMCIF hardware block.
1946 config ZBOOT_ROM_SH_MOBILE_SDHI
1947 bool "Include SuperH Mobile SDHI loader in zImage (EXPERIMENTAL)"
1949 Load image from SDHI hardware block
1953 config ARM_APPENDED_DTB
1954 bool "Use appended device tree blob to zImage (EXPERIMENTAL)"
1955 depends on OF && !ZBOOT_ROM && EXPERIMENTAL
1957 With this option, the boot code will look for a device tree binary
1958 (DTB) appended to zImage
1959 (e.g. cat zImage <filename>.dtb > zImage_w_dtb).
1961 This is meant as a backward compatibility convenience for those
1962 systems with a bootloader that can't be upgraded to accommodate
1963 the documented boot protocol using a device tree.
1965 Beware that there is very little in terms of protection against
1966 this option being confused by leftover garbage in memory that might
1967 look like a DTB header after a reboot if no actual DTB is appended
1968 to zImage. Do not leave this option active in a production kernel
1969 if you don't intend to always append a DTB. Proper passing of the
1970 location into r2 of a bootloader provided DTB is always preferable
1973 config ARM_ATAG_DTB_COMPAT
1974 bool "Supplement the appended DTB with traditional ATAG information"
1975 depends on ARM_APPENDED_DTB
1977 Some old bootloaders can't be updated to a DTB capable one, yet
1978 they provide ATAGs with memory configuration, the ramdisk address,
1979 the kernel cmdline string, etc. Such information is dynamically
1980 provided by the bootloader and can't always be stored in a static
1981 DTB. To allow a device tree enabled kernel to be used with such
1982 bootloaders, this option allows zImage to extract the information
1983 from the ATAG list and store it at run time into the appended DTB.
1986 prompt "Kernel command line type" if ARM_ATAG_DTB_COMPAT
1987 default ARM_ATAG_DTB_COMPAT_CMDLINE_FROM_BOOTLOADER
1989 config ARM_ATAG_DTB_COMPAT_CMDLINE_FROM_BOOTLOADER
1990 bool "Use bootloader kernel arguments if available"
1992 Uses the command-line options passed by the boot loader instead of
1993 the device tree bootargs property. If the boot loader doesn't provide
1994 any, the device tree bootargs property will be used.
1996 config ARM_ATAG_DTB_COMPAT_CMDLINE_EXTEND
1997 bool "Extend with bootloader kernel arguments"
1999 The command-line arguments provided by the boot loader will be
2000 appended to the the device tree bootargs property.
2005 string "Default kernel command string"
2008 On some architectures (EBSA110 and CATS), there is currently no way
2009 for the boot loader to pass arguments to the kernel. For these
2010 architectures, you should supply some command-line options at build
2011 time by entering them here. As a minimum, you should specify the
2012 memory size and the root device (e.g., mem=64M root=/dev/nfs).
2015 prompt "Kernel command line type" if CMDLINE != ""
2016 default CMDLINE_FROM_BOOTLOADER
2019 config CMDLINE_FROM_BOOTLOADER
2020 bool "Use bootloader kernel arguments if available"
2022 Uses the command-line options passed by the boot loader. If
2023 the boot loader doesn't provide any, the default kernel command
2024 string provided in CMDLINE will be used.
2026 config CMDLINE_EXTEND
2027 bool "Extend bootloader kernel arguments"
2029 The command-line arguments provided by the boot loader will be
2030 appended to the default kernel command string.
2032 config CMDLINE_FORCE
2033 bool "Always use the default kernel command string"
2035 Always use the default kernel command string, even if the boot
2036 loader passes other arguments to the kernel.
2037 This is useful if you cannot or don't want to change the
2038 command-line options your boot loader passes to the kernel.
2042 bool "Kernel Execute-In-Place from ROM"
2043 depends on !ZBOOT_ROM && !ARM_LPAE && !ARCH_MULTIPLATFORM
2045 Execute-In-Place allows the kernel to run from non-volatile storage
2046 directly addressable by the CPU, such as NOR flash. This saves RAM
2047 space since the text section of the kernel is not loaded from flash
2048 to RAM. Read-write sections, such as the data section and stack,
2049 are still copied to RAM. The XIP kernel is not compressed since
2050 it has to run directly from flash, so it will take more space to
2051 store it. The flash address used to link the kernel object files,
2052 and for storing it, is configuration dependent. Therefore, if you
2053 say Y here, you must know the proper physical address where to
2054 store the kernel image depending on your own flash memory usage.
2056 Also note that the make target becomes "make xipImage" rather than
2057 "make zImage" or "make Image". The final kernel binary to put in
2058 ROM memory will be arch/arm/boot/xipImage.
2062 config XIP_PHYS_ADDR
2063 hex "XIP Kernel Physical Location"
2064 depends on XIP_KERNEL
2065 default "0x00080000"
2067 This is the physical address in your flash memory the kernel will
2068 be linked for and stored to. This address is dependent on your
2072 bool "Kexec system call (EXPERIMENTAL)"
2073 depends on EXPERIMENTAL && (!SMP || HOTPLUG_CPU)
2075 kexec is a system call that implements the ability to shutdown your
2076 current kernel, and to start another kernel. It is like a reboot
2077 but it is independent of the system firmware. And like a reboot
2078 you can start any kernel with it, not just Linux.
2080 It is an ongoing process to be certain the hardware in a machine
2081 is properly shutdown, so do not be surprised if this code does not
2082 initially work for you. It may help to enable device hotplugging
2086 bool "Export atags in procfs"
2087 depends on ATAGS && KEXEC
2090 Should the atags used to boot the kernel be exported in an "atags"
2091 file in procfs. Useful with kexec.
2094 bool "Build kdump crash kernel (EXPERIMENTAL)"
2095 depends on EXPERIMENTAL
2097 Generate crash dump after being started by kexec. This should
2098 be normally only set in special crash dump kernels which are
2099 loaded in the main kernel with kexec-tools into a specially
2100 reserved region and then later executed after a crash by
2101 kdump/kexec. The crash dump kernel must be compiled to a
2102 memory address not used by the main kernel
2104 For more details see Documentation/kdump/kdump.txt
2106 config AUTO_ZRELADDR
2107 bool "Auto calculation of the decompressed kernel image address"
2108 depends on !ZBOOT_ROM && !ARCH_U300
2110 ZRELADDR is the physical address where the decompressed kernel
2111 image will be placed. If AUTO_ZRELADDR is selected, the address
2112 will be determined at run-time by masking the current IP with
2113 0xf8000000. This assumes the zImage being placed in the first 128MB
2114 from start of memory.
2118 menu "CPU Power Management"
2122 source "drivers/cpufreq/Kconfig"
2125 tristate "CPUfreq driver for i.MX CPUs"
2126 depends on ARCH_MXC && CPU_FREQ
2127 select CPU_FREQ_TABLE
2129 This enables the CPUfreq driver for i.MX CPUs.
2131 config CPU_FREQ_SA1100
2134 config CPU_FREQ_SA1110
2137 config CPU_FREQ_INTEGRATOR
2138 tristate "CPUfreq driver for ARM Integrator CPUs"
2139 depends on ARCH_INTEGRATOR && CPU_FREQ
2142 This enables the CPUfreq driver for ARM Integrator CPUs.
2144 For details, take a look at <file:Documentation/cpu-freq>.
2150 depends on CPU_FREQ && ARCH_PXA && PXA25x
2152 select CPU_FREQ_TABLE
2153 select CPU_FREQ_DEFAULT_GOV_USERSPACE
2158 Internal configuration node for common cpufreq on Samsung SoC
2160 config CPU_FREQ_S3C24XX
2161 bool "CPUfreq driver for Samsung S3C24XX series CPUs (EXPERIMENTAL)"
2162 depends on ARCH_S3C24XX && CPU_FREQ && EXPERIMENTAL
2165 This enables the CPUfreq driver for the Samsung S3C24XX family
2168 For details, take a look at <file:Documentation/cpu-freq>.
2172 config CPU_FREQ_S3C24XX_PLL
2173 bool "Support CPUfreq changing of PLL frequency (EXPERIMENTAL)"
2174 depends on CPU_FREQ_S3C24XX && EXPERIMENTAL
2176 Compile in support for changing the PLL frequency from the
2177 S3C24XX series CPUfreq driver. The PLL takes time to settle
2178 after a frequency change, so by default it is not enabled.
2180 This also means that the PLL tables for the selected CPU(s) will
2181 be built which may increase the size of the kernel image.
2183 config CPU_FREQ_S3C24XX_DEBUG
2184 bool "Debug CPUfreq Samsung driver core"
2185 depends on CPU_FREQ_S3C24XX
2187 Enable s3c_freq_dbg for the Samsung S3C CPUfreq core
2189 config CPU_FREQ_S3C24XX_IODEBUG
2190 bool "Debug CPUfreq Samsung driver IO timing"
2191 depends on CPU_FREQ_S3C24XX
2193 Enable s3c_freq_iodbg for the Samsung S3C CPUfreq core
2195 config CPU_FREQ_S3C24XX_DEBUGFS
2196 bool "Export debugfs for CPUFreq"
2197 depends on CPU_FREQ_S3C24XX && DEBUG_FS
2199 Export status information via debugfs.
2203 source "drivers/cpuidle/Kconfig"
2207 menu "Floating point emulation"
2209 comment "At least one emulation must be selected"
2212 bool "NWFPE math emulation"
2213 depends on (!AEABI || OABI_COMPAT) && !THUMB2_KERNEL
2215 Say Y to include the NWFPE floating point emulator in the kernel.
2216 This is necessary to run most binaries. Linux does not currently
2217 support floating point hardware so you need to say Y here even if
2218 your machine has an FPA or floating point co-processor podule.
2220 You may say N here if you are going to load the Acorn FPEmulator
2221 early in the bootup.
2224 bool "Support extended precision"
2225 depends on FPE_NWFPE
2227 Say Y to include 80-bit support in the kernel floating-point
2228 emulator. Otherwise, only 32 and 64-bit support is compiled in.
2229 Note that gcc does not generate 80-bit operations by default,
2230 so in most cases this option only enlarges the size of the
2231 floating point emulator without any good reason.
2233 You almost surely want to say N here.
2236 bool "FastFPE math emulation (EXPERIMENTAL)"
2237 depends on (!AEABI || OABI_COMPAT) && !CPU_32v3 && EXPERIMENTAL
2239 Say Y here to include the FAST floating point emulator in the kernel.
2240 This is an experimental much faster emulator which now also has full
2241 precision for the mantissa. It does not support any exceptions.
2242 It is very simple, and approximately 3-6 times faster than NWFPE.
2244 It should be sufficient for most programs. It may be not suitable
2245 for scientific calculations, but you have to check this for yourself.
2246 If you do not feel you need a faster FP emulation you should better
2250 bool "VFP-format floating point maths"
2251 depends on CPU_V6 || CPU_V6K || CPU_ARM926T || CPU_V7 || CPU_FEROCEON
2253 Say Y to include VFP support code in the kernel. This is needed
2254 if your hardware includes a VFP unit.
2256 Please see <file:Documentation/arm/VFP/release-notes.txt> for
2257 release notes and additional status information.
2259 Say N if your target does not have VFP hardware.
2267 bool "Advanced SIMD (NEON) Extension support"
2268 depends on VFPv3 && CPU_V7
2270 Say Y to include support code for NEON, the ARMv7 Advanced SIMD
2275 menu "Userspace binary formats"
2277 source "fs/Kconfig.binfmt"
2280 tristate "RISC OS personality"
2283 Say Y here to include the kernel code necessary if you want to run
2284 Acorn RISC OS/Arthur binaries under Linux. This code is still very
2285 experimental; if this sounds frightening, say N and sleep in peace.
2286 You can also say M here to compile this support as a module (which
2287 will be called arthur).
2291 menu "Power management options"
2293 source "kernel/power/Kconfig"
2295 config ARCH_SUSPEND_POSSIBLE
2296 depends on !ARCH_S5PC100
2297 depends on CPU_ARM920T || CPU_ARM926T || CPU_SA1100 || \
2298 CPU_V6 || CPU_V6K || CPU_V7 || CPU_XSC3 || CPU_XSCALE || CPU_MOHAWK
2301 config ARM_CPU_SUSPEND
2306 source "net/Kconfig"
2308 source "drivers/Kconfig"
2312 source "arch/arm/Kconfig.debug"
2314 source "security/Kconfig"
2316 source "crypto/Kconfig"
2318 source "lib/Kconfig"