2 * Copyright (C) 2013 Pavel Machek <pavel@ucw.cz>
3 * Copyright (C) 2013-2014 Aaro Koskinen <aaro.koskinen@iki.fi>
5 * This program is free software; you can redistribute it and/or modify
6 * it under the terms of the GNU General Public License version 2 (or later) as
7 * published by the Free Software Foundation.
12 #include "omap34xx.dtsi"
13 #include <dt-bindings/input/input.h>
16 * Default secure signed bootloader (Nokia X-Loader) does not enable L3 firewall
17 * for omap AES HW crypto support. When linux kernel try to access memory of AES
18 * blocks then kernel receive "Unhandled fault: external abort on non-linefetch"
19 * and crash. Until somebody fix omap-aes.c and omap_hwmod_3xxx_data.c code (no
20 * crash anymore) omap AES support will be disabled for all Nokia N900 devices.
21 * There is "unofficial" version of bootloader which enables AES in L3 firewall
22 * but it is not widely used and to prevent kernel crash rather AES is disabled.
23 * There is also no runtime detection code if AES is disabled in L3 firewall...
31 compatible = "nokia,omap3-n900", "ti,omap3430", "ti,omap3";
47 compatible = "gpio-leds";
49 label = "debug::sleep";
50 gpios = <&gpio6 2 GPIO_ACTIVE_HIGH>; /* 162 */
51 linux,default-trigger = "default-on";
52 pinctrl-names = "default";
53 pinctrl-0 = <&debug_leds>;
58 device_type = "memory";
59 reg = <0x80000000 0x10000000>; /* 256 MB */
63 compatible = "gpio-keys";
66 label = "Camera Lens Cover";
67 gpios = <&gpio4 14 GPIO_ACTIVE_LOW>; /* 110 */
68 linux,input-type = <EV_SW>;
69 linux,code = <SW_CAMERA_LENS_COVER>;
74 label = "Camera Focus";
75 gpios = <&gpio3 4 GPIO_ACTIVE_LOW>; /* 68 */
76 linux,code = <KEY_CAMERA_FOCUS>;
81 label = "Camera Capture";
82 gpios = <&gpio3 5 GPIO_ACTIVE_LOW>; /* 69 */
83 linux,code = <KEY_CAMERA>;
88 label = "Lock Button";
89 gpios = <&gpio4 17 GPIO_ACTIVE_LOW>; /* 113 */
90 linux,code = <KEY_SCREENLOCK>;
95 label = "Keypad Slide";
96 gpios = <&gpio3 7 GPIO_ACTIVE_LOW>; /* 71 */
97 linux,input-type = <EV_SW>;
98 linux,code = <SW_KEYPAD_SLIDE>;
103 label = "Proximity Sensor";
104 gpios = <&gpio3 25 GPIO_ACTIVE_HIGH>; /* 89 */
105 linux,input-type = <EV_SW>;
106 linux,code = <SW_FRONT_PROXIMITY>;
112 compatible = "nxp,isp1707";
113 nxp,enable-gpio = <&gpio3 3 GPIO_ACTIVE_HIGH>;
114 usb-phy = <&usb2_phy>;
118 compatible = "composite-video-connector";
122 tv_connector_in: endpoint {
123 remote-endpoint = <&venc_out>;
129 compatible = "nokia,n900-audio";
131 nokia,cpu-dai = <&mcbsp2>;
132 nokia,audio-codec = <&tlv320aic3x>, <&tlv320aic3x_aux>;
133 nokia,headphone-amplifier = <&tpa6130a2>;
135 tvout-selection-gpios = <&gpio2 8 GPIO_ACTIVE_HIGH>; /* 40 */
136 jack-detection-gpios = <&gpio6 17 GPIO_ACTIVE_HIGH>; /* 177 */
137 eci-switch-gpios = <&gpio6 22 GPIO_ACTIVE_HIGH>; /* 182 */
138 speaker-amplifier-gpios = <&twl_gpio 7 GPIO_ACTIVE_HIGH>;
141 battery: n900-battery {
142 compatible = "nokia,n900-battery";
143 io-channels = <&twl_madc 0>, <&twl_madc 4>, <&twl_madc 12>;
144 io-channel-names = "temp", "bsi", "vbat";
148 compatible = "ti,omap-dmtimer-pwm";
150 ti,timers = <&timer9>;
151 ti,clock-source = <0x00>; /* timer_sys_ck */
155 compatible = "nokia,n900-ir";
156 pwms = <&pwm9 0 26316 0>; /* 38000 Hz */
159 /* controlled (enabled/disabled) directly by bcm2048 and wl1251 */
161 compatible = "fixed-clock";
163 clock-frequency = <38400000>;
168 pinctrl-names = "default";
170 uart2_pins: pinmux_uart2_pins {
171 pinctrl-single,pins = <
172 OMAP3_CORE1_IOPAD(0x2174, PIN_INPUT_PULLUP | MUX_MODE0) /* uart2_cts */
173 OMAP3_CORE1_IOPAD(0x2176, PIN_OUTPUT | MUX_MODE0) /* uart2_rts */
174 OMAP3_CORE1_IOPAD(0x2178, PIN_OUTPUT | MUX_MODE0) /* uart2_tx */
175 OMAP3_CORE1_IOPAD(0x217a, PIN_INPUT | MUX_MODE0) /* uart2_rx */
179 uart3_pins: pinmux_uart3_pins {
180 pinctrl-single,pins = <
181 OMAP3_CORE1_IOPAD(0x219e, PIN_INPUT | MUX_MODE0) /* uart3_rx */
182 OMAP3_CORE1_IOPAD(0x21a0, PIN_OUTPUT | MUX_MODE0) /* uart3_tx */
186 ethernet_pins: pinmux_ethernet_pins {
187 pinctrl-single,pins = <
188 OMAP3_CORE1_IOPAD(0x20b4, PIN_INPUT_PULLDOWN | MUX_MODE4) /* gpmc_ncs3.gpio_54 */
189 OMAP3_CORE1_IOPAD(0x20fc, PIN_OUTPUT | MUX_MODE4) /* dss_data16.gpio_86 */
190 OMAP3_CORE1_IOPAD(0x219c, PIN_OUTPUT | MUX_MODE4) /* uart3_rts_sd.gpio_164 */
194 gpmc_pins: pinmux_gpmc_pins {
195 pinctrl-single,pins = <
198 OMAP3_CORE1_IOPAD(0x207a, PIN_OUTPUT | MUX_MODE0) /* gpmc_a1.gpmc_a1 */
199 OMAP3_CORE1_IOPAD(0x207c, PIN_OUTPUT | MUX_MODE0) /* gpmc_a2.gpmc_a2 */
200 OMAP3_CORE1_IOPAD(0x207e, PIN_OUTPUT | MUX_MODE0) /* gpmc_a3.gpmc_a3 */
202 /* data lines, gpmc_d0..d7 not muxable according to TRM */
203 OMAP3_CORE1_IOPAD(0x209e, PIN_INPUT | MUX_MODE0) /* gpmc_d8.gpmc_d8 */
204 OMAP3_CORE1_IOPAD(0x20a0, PIN_INPUT | MUX_MODE0) /* gpmc_d9.gpmc_d9 */
205 OMAP3_CORE1_IOPAD(0x20a2, PIN_INPUT | MUX_MODE0) /* gpmc_d10.gpmc_d10 */
206 OMAP3_CORE1_IOPAD(0x20a4, PIN_INPUT | MUX_MODE0) /* gpmc_d11.gpmc_d11 */
207 OMAP3_CORE1_IOPAD(0x20a6, PIN_INPUT | MUX_MODE0) /* gpmc_d12.gpmc_d12 */
208 OMAP3_CORE1_IOPAD(0x20a8, PIN_INPUT | MUX_MODE0) /* gpmc_d13.gpmc_d13 */
209 OMAP3_CORE1_IOPAD(0x20aa, PIN_INPUT | MUX_MODE0) /* gpmc_d14.gpmc_d14 */
210 OMAP3_CORE1_IOPAD(0x20ac, PIN_INPUT | MUX_MODE0) /* gpmc_d15.gpmc_d15 */
213 * gpmc_ncs0, gpmc_nadv_ale, gpmc_noe, gpmc_nwe, gpmc_wait0 not muxable
214 * according to TRM. OneNAND seems to require PIN_INPUT on clock.
216 OMAP3_CORE1_IOPAD(0x20b0, PIN_OUTPUT | MUX_MODE0) /* gpmc_ncs1.gpmc_ncs1 */
217 OMAP3_CORE1_IOPAD(0x20be, PIN_INPUT | MUX_MODE0) /* gpmc_clk.gpmc_clk */
221 i2c1_pins: pinmux_i2c1_pins {
222 pinctrl-single,pins = <
223 OMAP3_CORE1_IOPAD(0x21ba, PIN_INPUT | MUX_MODE0) /* i2c1_scl */
224 OMAP3_CORE1_IOPAD(0x21bc, PIN_INPUT | MUX_MODE0) /* i2c1_sda */
228 i2c2_pins: pinmux_i2c2_pins {
229 pinctrl-single,pins = <
230 OMAP3_CORE1_IOPAD(0x21be, PIN_INPUT | MUX_MODE0) /* i2c2_scl */
231 OMAP3_CORE1_IOPAD(0x21c0, PIN_INPUT | MUX_MODE0) /* i2c2_sda */
235 i2c3_pins: pinmux_i2c3_pins {
236 pinctrl-single,pins = <
237 OMAP3_CORE1_IOPAD(0x21c2, PIN_INPUT | MUX_MODE0) /* i2c3_scl */
238 OMAP3_CORE1_IOPAD(0x21c4, PIN_INPUT | MUX_MODE0) /* i2c3_sda */
242 debug_leds: pinmux_debug_led_pins {
243 pinctrl-single,pins = <
244 OMAP3_CORE1_IOPAD(0x2198, PIN_OUTPUT | MUX_MODE4) /* mcbsp1_clkx.gpio_162 */
248 mcspi4_pins: pinmux_mcspi4_pins {
249 pinctrl-single,pins = <
250 OMAP3_CORE1_IOPAD(0x218c, PIN_INPUT_PULLDOWN | MUX_MODE1) /* mcspi4_clk */
251 OMAP3_CORE1_IOPAD(0x2192, PIN_INPUT_PULLDOWN | MUX_MODE1) /* mcspi4_somi */
252 OMAP3_CORE1_IOPAD(0x2190, PIN_OUTPUT | MUX_MODE1) /* mcspi4_simo */
253 OMAP3_CORE1_IOPAD(0x2196, PIN_OUTPUT | MUX_MODE1) /* mcspi4_cs0 */
257 mmc1_pins: pinmux_mmc1_pins {
258 pinctrl-single,pins = <
259 OMAP3_CORE1_IOPAD(0x2144, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_clk */
260 OMAP3_CORE1_IOPAD(0x2146, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_cmd */
261 OMAP3_CORE1_IOPAD(0x2148, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat0 */
262 OMAP3_CORE1_IOPAD(0x214a, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat1 */
263 OMAP3_CORE1_IOPAD(0x214c, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat2 */
264 OMAP3_CORE1_IOPAD(0x214e, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat3 */
268 mmc2_pins: pinmux_mmc2_pins {
269 pinctrl-single,pins = <
270 OMAP3_CORE1_IOPAD(0x2158, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_clk */
271 OMAP3_CORE1_IOPAD(0x215a, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_cmd */
272 OMAP3_CORE1_IOPAD(0x215c, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat0 */
273 OMAP3_CORE1_IOPAD(0x215e, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat1 */
274 OMAP3_CORE1_IOPAD(0x2160, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat2 */
275 OMAP3_CORE1_IOPAD(0x2162, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat3 */
276 OMAP3_CORE1_IOPAD(0x2164, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat4 */
277 OMAP3_CORE1_IOPAD(0x2166, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat5 */
278 OMAP3_CORE1_IOPAD(0x2168, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat6 */
279 OMAP3_CORE1_IOPAD(0x216a, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat7 */
283 acx565akm_pins: pinmux_acx565akm_pins {
284 pinctrl-single,pins = <
285 OMAP3_CORE1_IOPAD(0x2104, PIN_OUTPUT | MUX_MODE4) /* RX51_LCD_RESET_GPIO */
289 dss_sdi_pins: pinmux_dss_sdi_pins {
290 pinctrl-single,pins = <
291 OMAP3_CORE1_IOPAD(0x20f0, PIN_OUTPUT | MUX_MODE1) /* dss_data10.sdi_dat1n */
292 OMAP3_CORE1_IOPAD(0x20f2, PIN_OUTPUT | MUX_MODE1) /* dss_data11.sdi_dat1p */
293 OMAP3_CORE1_IOPAD(0x20f4, PIN_OUTPUT | MUX_MODE1) /* dss_data12.sdi_dat2n */
294 OMAP3_CORE1_IOPAD(0x20f6, PIN_OUTPUT | MUX_MODE1) /* dss_data13.sdi_dat2p */
296 OMAP3_CORE1_IOPAD(0x2108, PIN_OUTPUT | MUX_MODE1) /* dss_data22.sdi_clkp */
297 OMAP3_CORE1_IOPAD(0x210a, PIN_OUTPUT | MUX_MODE1) /* dss_data23.sdi_clkn */
301 wl1251_pins: pinmux_wl1251 {
302 pinctrl-single,pins = <
303 OMAP3_CORE1_IOPAD(0x20fe, PIN_OUTPUT | MUX_MODE4) /* gpio 87 => wl1251 enable */
304 OMAP3_CORE1_IOPAD(0x208a, PIN_INPUT | MUX_MODE4) /* gpio 42 => wl1251 irq */
308 ssi_pins: pinmux_ssi {
309 pinctrl-single,pins = <
310 OMAP3_CORE1_IOPAD(0x2180, PIN_INPUT_PULLUP | MUX_MODE1) /* ssi1_rdy_tx */
311 OMAP3_CORE1_IOPAD(0x217e, PIN_OUTPUT | MUX_MODE1) /* ssi1_flag_tx */
312 OMAP3_CORE1_IOPAD(0x2182, PIN_INPUT | MUX_MODE4) /* ssi1_wake_tx (cawake) */
313 OMAP3_CORE1_IOPAD(0x217c, PIN_OUTPUT | MUX_MODE1) /* ssi1_dat_tx */
314 OMAP3_CORE1_IOPAD(0x2184, PIN_INPUT | MUX_MODE1) /* ssi1_dat_rx */
315 OMAP3_CORE1_IOPAD(0x2186, PIN_INPUT | MUX_MODE1) /* ssi1_flag_rx */
316 OMAP3_CORE1_IOPAD(0x2188, PIN_OUTPUT | MUX_MODE1) /* ssi1_rdy_rx */
317 OMAP3_CORE1_IOPAD(0x218a, PIN_OUTPUT | MUX_MODE1) /* ssi1_wake */
321 modem_pins: pinmux_modem {
322 pinctrl-single,pins = <
323 OMAP3_CORE1_IOPAD(0x20dc, PIN_OUTPUT | MUX_MODE4) /* gpio 70 => cmt_apeslpx */
324 OMAP3_CORE1_IOPAD(0x20e0, PIN_INPUT | MUX_MODE4) /* gpio 72 => ape_rst_rq */
325 OMAP3_CORE1_IOPAD(0x20e2, PIN_OUTPUT | MUX_MODE4) /* gpio 73 => cmt_rst_rq */
326 OMAP3_CORE1_IOPAD(0x20e4, PIN_OUTPUT | MUX_MODE4) /* gpio 74 => cmt_en */
327 OMAP3_CORE1_IOPAD(0x20e6, PIN_OUTPUT | MUX_MODE4) /* gpio 75 => cmt_rst */
328 OMAP3_CORE1_IOPAD(0x218e, PIN_OUTPUT | MUX_MODE4) /* gpio 157 => cmt_bsi */
334 pinctrl-names = "default";
335 pinctrl-0 = <&i2c1_pins>;
337 clock-frequency = <2200000>;
341 interrupts = <7>; /* SYS_NIRQ cascaded to intc */
342 interrupt-parent = <&intc>;
346 #include "twl4030.dtsi"
347 #include "twl4030_omap3.dtsi"
350 regulator-name = "V28";
351 regulator-min-microvolt = <2800000>;
352 regulator-max-microvolt = <2800000>;
353 regulator-initial-mode = <0x0e>; /* RES_STATE_ACTIVE */
354 regulator-always-on; /* due to battery cover sensor */
358 regulator-name = "VCSI";
359 regulator-min-microvolt = <1800000>;
360 regulator-max-microvolt = <1800000>;
361 regulator-initial-mode = <0x0e>; /* RES_STATE_ACTIVE */
365 regulator-name = "VMMC2_30";
366 regulator-min-microvolt = <2800000>;
367 regulator-max-microvolt = <3000000>;
368 regulator-initial-mode = <0x0e>; /* RES_STATE_ACTIVE */
372 regulator-name = "VCAM_ANA_28";
373 regulator-min-microvolt = <2800000>;
374 regulator-max-microvolt = <2800000>;
375 regulator-initial-mode = <0x0e>; /* RES_STATE_ACTIVE */
379 regulator-name = "VMMC1";
380 regulator-min-microvolt = <1850000>;
381 regulator-max-microvolt = <3150000>;
382 regulator-initial-mode = <0x0e>; /* RES_STATE_ACTIVE */
386 regulator-name = "V28_A";
387 regulator-min-microvolt = <2800000>;
388 regulator-max-microvolt = <3000000>;
389 regulator-initial-mode = <0x0e>; /* RES_STATE_ACTIVE */
390 regulator-always-on; /* due VIO leak to AIC34 VDDs */
394 regulator-name = "VPLL";
395 regulator-min-microvolt = <1800000>;
396 regulator-max-microvolt = <1800000>;
397 regulator-initial-mode = <0x0e>; /* RES_STATE_ACTIVE */
402 regulator-name = "VSDI_CSI";
403 regulator-min-microvolt = <1800000>;
404 regulator-max-microvolt = <1800000>;
405 regulator-initial-mode = <0x0e>; /* RES_STATE_ACTIVE */
410 regulator-name = "VMMC2_IO_18";
411 regulator-min-microvolt = <1800000>;
412 regulator-max-microvolt = <1800000>;
413 regulator-initial-mode = <0x0e>; /* RES_STATE_ACTIVE */
417 regulator-name = "VIO";
418 regulator-min-microvolt = <1800000>;
419 regulator-max-microvolt = <1800000>;
423 regulator-name = "VINTANA1";
424 /* fixed to 1500000 */
429 regulator-name = "VINTANA2";
430 regulator-min-microvolt = <2750000>;
431 regulator-max-microvolt = <2750000>;
436 regulator-name = "VINTDIG";
437 /* fixed to 1500000 */
443 compatible = "ti,twl4030-audio";
444 ti,enable-vibra = <1>;
448 compatible = "ti,twl4030-power-n900", "ti,twl4030-power-idle-osc-off";
454 linux,keymap = < MATRIX_KEY(0x00, 0x00, KEY_Q)
455 MATRIX_KEY(0x00, 0x01, KEY_O)
456 MATRIX_KEY(0x00, 0x02, KEY_P)
457 MATRIX_KEY(0x00, 0x03, KEY_COMMA)
458 MATRIX_KEY(0x00, 0x04, KEY_BACKSPACE)
459 MATRIX_KEY(0x00, 0x06, KEY_A)
460 MATRIX_KEY(0x00, 0x07, KEY_S)
462 MATRIX_KEY(0x01, 0x00, KEY_W)
463 MATRIX_KEY(0x01, 0x01, KEY_D)
464 MATRIX_KEY(0x01, 0x02, KEY_F)
465 MATRIX_KEY(0x01, 0x03, KEY_G)
466 MATRIX_KEY(0x01, 0x04, KEY_H)
467 MATRIX_KEY(0x01, 0x05, KEY_J)
468 MATRIX_KEY(0x01, 0x06, KEY_K)
469 MATRIX_KEY(0x01, 0x07, KEY_L)
471 MATRIX_KEY(0x02, 0x00, KEY_E)
472 MATRIX_KEY(0x02, 0x01, KEY_DOT)
473 MATRIX_KEY(0x02, 0x02, KEY_UP)
474 MATRIX_KEY(0x02, 0x03, KEY_ENTER)
475 MATRIX_KEY(0x02, 0x05, KEY_Z)
476 MATRIX_KEY(0x02, 0x06, KEY_X)
477 MATRIX_KEY(0x02, 0x07, KEY_C)
478 MATRIX_KEY(0x02, 0x08, KEY_F9)
480 MATRIX_KEY(0x03, 0x00, KEY_R)
481 MATRIX_KEY(0x03, 0x01, KEY_V)
482 MATRIX_KEY(0x03, 0x02, KEY_B)
483 MATRIX_KEY(0x03, 0x03, KEY_N)
484 MATRIX_KEY(0x03, 0x04, KEY_M)
485 MATRIX_KEY(0x03, 0x05, KEY_SPACE)
486 MATRIX_KEY(0x03, 0x06, KEY_SPACE)
487 MATRIX_KEY(0x03, 0x07, KEY_LEFT)
489 MATRIX_KEY(0x04, 0x00, KEY_T)
490 MATRIX_KEY(0x04, 0x01, KEY_DOWN)
491 MATRIX_KEY(0x04, 0x02, KEY_RIGHT)
492 MATRIX_KEY(0x04, 0x04, KEY_LEFTCTRL)
493 MATRIX_KEY(0x04, 0x05, KEY_RIGHTALT)
494 MATRIX_KEY(0x04, 0x06, KEY_LEFTSHIFT)
495 MATRIX_KEY(0x04, 0x08, KEY_F10)
497 MATRIX_KEY(0x05, 0x00, KEY_Y)
498 MATRIX_KEY(0x05, 0x08, KEY_F11)
500 MATRIX_KEY(0x06, 0x00, KEY_U)
502 MATRIX_KEY(0x07, 0x00, KEY_I)
503 MATRIX_KEY(0x07, 0x01, KEY_F7)
504 MATRIX_KEY(0x07, 0x02, KEY_F8)
510 ti,pulldowns = <0x03ff3f>; /* BIT(0..5) | BIT(8..17) */
514 pinctrl-names = "default";
515 pinctrl-0 = <&i2c2_pins>;
517 clock-frequency = <100000>;
519 tlv320aic3x: tlv320aic3x@18 {
520 compatible = "ti,tlv320aic3x";
522 gpio-reset = <&gpio2 28 GPIO_ACTIVE_HIGH>; /* 60 */
524 0 /* AIC3X_GPIO1_FUNC_DISABLED */
525 5 /* AIC3X_GPIO2_FUNC_DIGITAL_MIC_INPUT */
528 AVDD-supply = <&vmmc2>;
529 DRVDD-supply = <&vmmc2>;
530 IOVDD-supply = <&vio>;
531 DVDD-supply = <&vio>;
533 ai3x-micbias-vg = <1>;
536 tlv320aic3x_aux: tlv320aic3x@19 {
537 compatible = "ti,tlv320aic3x";
539 gpio-reset = <&gpio2 28 GPIO_ACTIVE_HIGH>; /* 60 */
541 AVDD-supply = <&vmmc2>;
542 DRVDD-supply = <&vmmc2>;
543 IOVDD-supply = <&vio>;
544 DVDD-supply = <&vio>;
546 ai3x-micbias-vg = <2>;
549 tsl2563: tsl2563@29 {
550 compatible = "amstaos,tsl2563";
553 amstaos,cover-comp-gain = <16>;
556 adp1653: led-controller@30 {
557 compatible = "adi,adp1653";
559 enable-gpios = <&gpio3 24 GPIO_ACTIVE_HIGH>; /* 88 */
562 flash-timeout-us = <500000>;
563 flash-max-microamp = <320000>;
564 led-max-microamp = <50000>;
567 led-max-microamp = <17500>;
572 compatible = "national,lp5523";
574 clock-mode = /bits/ 8 <0>; /* LP55XX_CLOCK_AUTO */
575 enable-gpio = <&gpio2 9 GPIO_ACTIVE_HIGH>; /* 41 */
578 chan-name = "lp5523:kb1";
579 led-cur = /bits/ 8 <50>;
580 max-cur = /bits/ 8 <100>;
584 chan-name = "lp5523:kb2";
585 led-cur = /bits/ 8 <50>;
586 max-cur = /bits/ 8 <100>;
590 chan-name = "lp5523:kb3";
591 led-cur = /bits/ 8 <50>;
592 max-cur = /bits/ 8 <100>;
596 chan-name = "lp5523:kb4";
597 led-cur = /bits/ 8 <50>;
598 max-cur = /bits/ 8 <100>;
602 chan-name = "lp5523:b";
603 led-cur = /bits/ 8 <50>;
604 max-cur = /bits/ 8 <100>;
608 chan-name = "lp5523:g";
609 led-cur = /bits/ 8 <50>;
610 max-cur = /bits/ 8 <100>;
614 chan-name = "lp5523:r";
615 led-cur = /bits/ 8 <50>;
616 max-cur = /bits/ 8 <100>;
620 chan-name = "lp5523:kb5";
621 led-cur = /bits/ 8 <50>;
622 max-cur = /bits/ 8 <100>;
626 chan-name = "lp5523:kb6";
627 led-cur = /bits/ 8 <50>;
628 max-cur = /bits/ 8 <100>;
632 bq27200: bq27200@55 {
633 compatible = "ti,bq27200";
637 /* Stereo headphone amplifier */
638 tpa6130a2: tpa6130a2@60 {
639 compatible = "ti,tpa6130a2";
642 Vdd-supply = <&vmmc2>;
644 power-gpio = <&gpio4 2 GPIO_ACTIVE_HIGH>; /* 98 */
648 compatible = "silabs,si4713";
651 interrupts-extended = <&gpio2 21 IRQ_TYPE_EDGE_FALLING>; /* 53 */
652 reset-gpios = <&gpio6 3 GPIO_ACTIVE_HIGH>; /* 163 */
654 vdd-supply = <&vaux1>;
657 bq24150a: bq24150a@6b {
658 compatible = "ti,bq24150a";
661 ti,current-limit = <100>;
662 ti,weak-battery-voltage = <3400>;
663 ti,battery-regulation-voltage = <4200>;
664 ti,charge-current = <650>;
665 ti,termination-current = <100>;
666 ti,resistor-sense = <68>;
668 ti,usb-charger-detection = <&isp1707>;
673 pinctrl-names = "default";
674 pinctrl-0 = <&i2c3_pins>;
676 clock-frequency = <400000>;
678 lis302dl: lis3lv02d@1d {
679 compatible = "st,lis3lv02d";
682 Vdd-supply = <&vaux1>;
683 Vdd_IO-supply = <&vio>;
685 interrupt-parent = <&gpio6>;
686 interrupts = <21 20>; /* 181 and 180 */
693 /* Limits are 0.5g * value */
694 st,click-threshold-x = <8>;
695 st,click-threshold-y = <8>;
696 st,click-threshold-z = <10>;
698 /* Click must be longer than time limit */
699 st,click-time-limit = <9>;
701 /* Kind of debounce filter */
702 st,click-latency = <50>;
704 /* Interrupt line 2 for click detection */
709 st,wakeup-threshold = <(800/18)>; /* millig-value / 18 to get HW values */
712 st,wakeup2-threshold = <(900/18)>; /* millig-value / 18 to get HW values */
717 st,axis-x = <1>; /* LIS3_DEV_X */
718 st,axis-y = <(-2)>; /* LIS3_INV_DEV_Y */
719 st,axis-z = <(-3)>; /* LIS3_INV_DEV_Z */
721 st,min-limit-x = <(-32)>;
722 st,min-limit-y = <3>;
723 st,min-limit-z = <3>;
725 st,max-limit-x = <(-3)>;
726 st,max-limit-y = <32>;
727 st,max-limit-z = <32>;
732 pinctrl-names = "default";
733 pinctrl-0 = <&mmc1_pins>;
734 vmmc-supply = <&vmmc1>;
736 cd-gpios = <&gpio6 0 GPIO_ACTIVE_HIGH>; /* 160 */
739 /* most boards use vaux3, only some old versions use vmmc2 instead */
741 pinctrl-names = "default";
742 pinctrl-0 = <&mmc2_pins>;
743 vmmc-supply = <&vaux3>;
744 vmmc_aux-supply = <&vsim>;
756 ranges = <0 0 0x01000000 0x01000000>, /* 16 MB for OneNAND */
757 <1 0 0x02000000 0x01000000>; /* 16 MB for smc91c96 */
758 pinctrl-names = "default";
759 pinctrl-0 = <&gpmc_pins>;
761 /* sys_ndmareq1 could be used by the driver, not as gpio65 though */
763 #address-cells = <1>;
765 reg = <0 0 0x20000>; /* CS0, offset 0, IO size 128K */
769 gpmc,burst-length = <16>;
773 gpmc,device-width = <2>; /* GPMC_DEVWIDTH_16BIT */
774 gpmc,mux-add-data = <2>; /* GPMC_MUX_AD */
776 gpmc,cs-rd-off-ns = <87>;
777 gpmc,cs-wr-off-ns = <87>;
778 gpmc,adv-on-ns = <0>;
779 gpmc,adv-rd-off-ns = <10>;
780 gpmc,adv-wr-off-ns = <10>;
781 gpmc,oe-on-ns = <15>;
782 gpmc,oe-off-ns = <87>;
784 gpmc,we-off-ns = <87>;
785 gpmc,rd-cycle-ns = <112>;
786 gpmc,wr-cycle-ns = <112>;
787 gpmc,access-ns = <81>;
788 gpmc,page-burst-access-ns = <15>;
789 gpmc,bus-turnaround-ns = <0>;
790 gpmc,cycle2cycle-delay-ns = <0>;
791 gpmc,wait-monitoring-ns = <0>;
792 gpmc,clk-activation-ns = <5>;
793 gpmc,wr-data-mux-bus-ns = <30>;
794 gpmc,wr-access-ns = <81>;
795 gpmc,sync-clk-ps = <15000>;
798 * MTD partition table corresponding to Nokia's
799 * Maemo 5 (Fremantle) release.
802 label = "bootloader";
803 reg = <0x00000000 0x00020000>;
808 reg = <0x00020000 0x00060000>;
812 reg = <0x00080000 0x00040000>;
816 reg = <0x000c0000 0x00200000>;
820 reg = <0x002c0000 0x00200000>;
824 reg = <0x004c0000 0x0fb40000>;
828 /* Ethernet is on some early development boards and qemu */
830 compatible = "smsc,lan91c94";
831 interrupt-parent = <&gpio2>;
832 interrupts = <22 IRQ_TYPE_LEVEL_HIGH>; /* gpio54 */
833 reg = <1 0 0xf>; /* 16 byte IO range */
835 pinctrl-names = "default";
836 pinctrl-0 = <ðernet_pins>;
837 power-gpios = <&gpio3 22 GPIO_ACTIVE_HIGH>; /* gpio86 */
838 reset-gpios = <&gpio6 4 GPIO_ACTIVE_HIGH>; /* gpio164 */
839 gpmc,device-width = <2>;
840 gpmc,sync-clk-ps = <0>;
842 gpmc,cs-rd-off-ns = <48>;
843 gpmc,cs-wr-off-ns = <24>;
844 gpmc,adv-on-ns = <0>;
845 gpmc,adv-rd-off-ns = <0>;
846 gpmc,adv-wr-off-ns = <0>;
847 gpmc,we-on-ns = <12>;
848 gpmc,we-off-ns = <18>;
849 gpmc,oe-on-ns = <12>;
850 gpmc,oe-off-ns = <48>;
851 gpmc,page-burst-access-ns = <0>;
852 gpmc,access-ns = <42>;
853 gpmc,rd-cycle-ns = <180>;
854 gpmc,wr-cycle-ns = <180>;
855 gpmc,bus-turnaround-ns = <0>;
856 gpmc,cycle2cycle-delay-ns = <0>;
857 gpmc,wait-monitoring-ns = <0>;
858 gpmc,clk-activation-ns = <0>;
859 gpmc,wr-access-ns = <0>;
860 gpmc,wr-data-mux-bus-ns = <12>;
866 * For some reason, touchscreen is necessary for screen to work at
867 * all on real hw. It works well without it on emulator.
869 * Also... order in the device tree actually matters here.
872 compatible = "ti,tsc2005";
873 spi-max-frequency = <6000000>;
878 reset-gpios = <&gpio4 8 GPIO_ACTIVE_HIGH>; /* 104 */
879 interrupts-extended = <&gpio4 4 IRQ_TYPE_EDGE_RISING>; /* 100 */
881 touchscreen-fuzz-x = <4>;
882 touchscreen-fuzz-y = <7>;
883 touchscreen-fuzz-pressure = <2>;
884 touchscreen-size-x = <4096>;
885 touchscreen-size-y = <4096>;
886 touchscreen-max-pressure = <2048>;
888 ti,x-plate-ohms = <280>;
889 ti,esd-recovery-timeout-ms = <8000>;
893 compatible = "sony,acx565akm";
894 spi-max-frequency = <6000000>;
897 pinctrl-names = "default";
898 pinctrl-0 = <&acx565akm_pins>;
901 reset-gpios = <&gpio3 26 GPIO_ACTIVE_HIGH>; /* 90 */
905 remote-endpoint = <&sdi_out>;
912 pinctrl-names = "default";
913 pinctrl-0 = <&mcspi4_pins>;
916 pinctrl-names = "default";
917 pinctrl-0 = <&wl1251_pins>;
921 compatible = "ti,wl1251";
923 spi-max-frequency = <48000000>;
928 ti,power-gpio = <&gpio3 23 GPIO_ACTIVE_HIGH>; /* 87 */
930 interrupt-parent = <&gpio2>;
931 interrupts = <10 IRQ_TYPE_NONE>; /* gpio line 42 */
938 interface-type = <0>;
939 usb-phy = <&usb2_phy>;
941 phy-names = "usb2-phy";
951 pinctrl-names = "default";
952 pinctrl-0 = <&uart2_pins>;
955 compatible = "brcm,bcm2048-nokia", "nokia,h4p-bluetooth";
956 reset-gpios = <&gpio3 27 GPIO_ACTIVE_LOW>; /* 91 */
957 host-wakeup-gpios = <&gpio4 5 GPIO_ACTIVE_HIGH>; /* 101 */
958 bluetooth-wakeup-gpios = <&gpio2 5 GPIO_ACTIVE_HIGH>; /* 37 */
960 clock-names = "sysclk";
965 interrupts-extended = <&intc 74 &omap3_pmx_core OMAP3_UART3_RX>;
966 pinctrl-names = "default";
967 pinctrl-0 = <&uart3_pins>;
973 pinctrl-names = "default";
974 pinctrl-0 = <&dss_sdi_pins>;
976 vdds_sdi-supply = <&vaux1>;
979 #address-cells = <1>;
986 remote-endpoint = <&lcd_in>;
996 vdda-supply = <&vdac>;
1000 remote-endpoint = <&tv_connector_in>;
1011 pinctrl-names = "default";
1012 pinctrl-0 = <&ssi_pins>;
1014 ti,ssi-cawake-gpio = <&gpio5 23 GPIO_ACTIVE_HIGH>; /* 151 */
1017 compatible = "nokia,n900-modem";
1019 pinctrl-names = "default";
1020 pinctrl-0 = <&modem_pins>;
1022 hsi-channel-ids = <0>, <1>, <2>, <3>;
1023 hsi-channel-names = "mcsaab-control",
1027 hsi-speed-kbps = <55000>;
1029 hsi-flow = "synchronized";
1030 hsi-arb-mode = "round-robin";
1032 interrupts-extended = <&gpio3 8 IRQ_TYPE_EDGE_FALLING>; /* 72 */
1034 gpios = <&gpio3 6 GPIO_ACTIVE_HIGH>, /* 70 */
1035 <&gpio3 9 GPIO_ACTIVE_HIGH>, /* 73 */
1036 <&gpio3 10 GPIO_ACTIVE_HIGH>, /* 74 */
1037 <&gpio3 11 GPIO_ACTIVE_HIGH>, /* 75 */
1038 <&gpio5 29 GPIO_ACTIVE_HIGH>; /* 157 */
1039 gpio-names = "cmt_apeslpx",
1048 status = "disabled";