3 * Sascha Hauer, Pengutronix
5 * (C) Copyright 2009 Freescale Semiconductor, Inc.
7 * SPDX-License-Identifier: GPL-2.0+
13 #include <asm/armv7.h>
14 #include <asm/bootm.h>
15 #include <asm/pl310.h>
16 #include <asm/errno.h>
18 #include <asm/arch/imx-regs.h>
19 #include <asm/arch/clock.h>
20 #include <asm/arch/regs-ocotp.h>
21 #include <asm/arch/sys_proto.h>
22 #include <asm/imx-common/boot_mode.h>
23 #include <asm/imx-common/dma.h>
25 #include <asm/arch/mxc_hdmi.h>
26 #include <asm/arch/crm_regs.h>
28 #include <imx_thermal.h>
30 DECLARE_GLOBAL_DATA_PTR;
32 #define __data __attribute__((section(".data")))
34 #ifdef CONFIG_MX6_TEMPERATURE_MIN
35 #define TEMPERATURE_MIN CONFIG_MX6_TEMPERATURE_MIN
37 #define TEMPERATURE_MIN (-40)
39 #ifdef CONFIG_MX6_TEMPERATURE_HOT
40 #define TEMPERATURE_HOT CONFIG_MX6_TEMPERATURE_HOT
42 #define TEMPERATURE_HOT 80
44 #ifdef CONFIG_MX6_TEMPERATURE_MAX
45 #define TEMPERATURE_MAX CONFIG_MX6_TEMPERATURE_MAX
47 #define TEMPERATURE_MAX 125
49 #define TEMP_AVG_COUNT 5
50 #define TEMP_WARN_THRESHOLD 5
66 #if defined(CONFIG_IMX6_THERMAL)
67 static const struct imx_thermal_plat imx6_thermal_plat = {
68 .regs = (void *)ANATOP_BASE_ADDR,
73 U_BOOT_DEVICE(imx6_thermal) = {
74 .name = "imx_thermal",
75 .platdata = &imx6_thermal_plat,
81 struct scu_regs *scu = (struct scu_regs *)SCU_BASE_ADDR;
82 return readl(&scu->config) & 3;
87 struct anatop_regs *anatop = (struct anatop_regs *)ANATOP_BASE_ADDR;
88 u32 reg = readl(&anatop->digprog_sololite);
89 u32 type = ((reg >> 16) & 0xff);
92 if (type != MXC_CPU_MX6SL) {
93 reg = readl(&anatop->digprog);
94 struct scu_regs *scu = (struct scu_regs *)SCU_BASE_ADDR;
95 cfg = readl(&scu->config) & 3;
96 type = ((reg >> 16) & 0xff);
97 if (type == MXC_CPU_MX6DL) {
99 type = MXC_CPU_MX6SOLO;
102 if (type == MXC_CPU_MX6Q) {
108 major = ((reg >> 8) & 0xff);
110 ((type == MXC_CPU_MX6Q) || (type == MXC_CPU_MX6D))) {
112 type = MXC_CPU_MX6QP;
114 type = MXC_CPU_MX6DP;
116 reg &= 0xff; /* mx6 silicon revision */
117 return (type << 12) | (reg + (0x10 * (major + 1)));
121 * OCOTP_CFG3[17:16] (see Fusemap Description Table offset 0x440)
122 * defines a 2-bit SPEED_GRADING
124 #define OCOTP_CFG3_SPEED_SHIFT 16
125 #define OCOTP_CFG3_SPEED_800MHZ 0
126 #define OCOTP_CFG3_SPEED_850MHZ 1
127 #define OCOTP_CFG3_SPEED_1GHZ 2
128 #define OCOTP_CFG3_SPEED_1P2GHZ 3
130 u32 get_cpu_speed_grade_hz(void)
132 struct ocotp_regs *ocotp = (struct ocotp_regs *)OCOTP_BASE_ADDR;
133 struct fuse_bank *bank = &ocotp->bank[0];
134 struct fuse_bank0_regs *fuse =
135 (struct fuse_bank0_regs *)bank->fuse_regs;
138 val = readl(&fuse->cfg3);
139 val >>= OCOTP_CFG3_SPEED_SHIFT;
143 /* Valid for IMX6DQ */
144 case OCOTP_CFG3_SPEED_1P2GHZ:
145 if (is_cpu_type(MXC_CPU_MX6Q) || is_cpu_type(MXC_CPU_MX6D))
147 /* Valid for IMX6SX/IMX6SDL/IMX6DQ */
148 case OCOTP_CFG3_SPEED_1GHZ:
150 /* Valid for IMX6DQ */
151 case OCOTP_CFG3_SPEED_850MHZ:
152 if (is_cpu_type(MXC_CPU_MX6Q) || is_cpu_type(MXC_CPU_MX6D))
154 /* Valid for IMX6SX/IMX6SDL/IMX6DQ */
155 case OCOTP_CFG3_SPEED_800MHZ:
162 * OCOTP_MEM0[7:6] (see Fusemap Description Table offset 0x480)
163 * defines a 2-bit Temperature Grade
165 * return temperature grade and min/max temperature in celcius
167 #define OCOTP_MEM0_TEMP_SHIFT 6
169 u32 get_cpu_temp_grade(int *minc, int *maxc)
171 struct ocotp_regs *ocotp = (struct ocotp_regs *)OCOTP_BASE_ADDR;
172 struct fuse_bank *bank = &ocotp->bank[1];
173 struct fuse_bank1_regs *fuse =
174 (struct fuse_bank1_regs *)bank->fuse_regs;
177 val = readl(&fuse->mem0);
178 val >>= OCOTP_MEM0_TEMP_SHIFT;
182 if (val == TEMP_AUTOMOTIVE) {
185 } else if (val == TEMP_INDUSTRIAL) {
188 } else if (val == TEMP_EXTCOMMERCIAL) {
199 #ifdef CONFIG_REVISION_TAG
200 u32 __weak get_board_rev(void)
202 u32 cpurev = get_cpu_rev();
203 u32 type = ((cpurev >> 12) & 0xff);
204 if (type == MXC_CPU_MX6SOLO)
205 cpurev = (MXC_CPU_MX6DL) << 12 | (cpurev & 0xFFF);
207 if (type == MXC_CPU_MX6D)
208 cpurev = (MXC_CPU_MX6Q) << 12 | (cpurev & 0xFFF);
216 struct aipstz_regs *aips1, *aips2;
217 #ifdef CONFIG_SOC_MX6SX
218 struct aipstz_regs *aips3;
221 aips1 = (struct aipstz_regs *)AIPS1_ARB_BASE_ADDR;
222 aips2 = (struct aipstz_regs *)AIPS2_ARB_BASE_ADDR;
223 #ifdef CONFIG_SOC_MX6SX
224 aips3 = (struct aipstz_regs *)AIPS3_ARB_BASE_ADDR;
228 * Set all MPROTx to be non-bufferable, trusted for R/W,
229 * not forced to user-mode.
231 writel(0x77777777, &aips1->mprot0);
232 writel(0x77777777, &aips1->mprot1);
233 writel(0x77777777, &aips2->mprot0);
234 writel(0x77777777, &aips2->mprot1);
237 * Set all OPACRx to be non-bufferable, not require
238 * supervisor privilege level for access,allow for
239 * write access and untrusted master access.
241 writel(0x00000000, &aips1->opacr0);
242 writel(0x00000000, &aips1->opacr1);
243 writel(0x00000000, &aips1->opacr2);
244 writel(0x00000000, &aips1->opacr3);
245 writel(0x00000000, &aips1->opacr4);
246 writel(0x00000000, &aips2->opacr0);
247 writel(0x00000000, &aips2->opacr1);
248 writel(0x00000000, &aips2->opacr2);
249 writel(0x00000000, &aips2->opacr3);
250 writel(0x00000000, &aips2->opacr4);
252 #ifdef CONFIG_SOC_MX6SX
254 * Set all MPROTx to be non-bufferable, trusted for R/W,
255 * not forced to user-mode.
257 writel(0x77777777, &aips3->mprot0);
258 writel(0x77777777, &aips3->mprot1);
261 * Set all OPACRx to be non-bufferable, not require
262 * supervisor privilege level for access,allow for
263 * write access and untrusted master access.
265 writel(0x00000000, &aips3->opacr0);
266 writel(0x00000000, &aips3->opacr1);
267 writel(0x00000000, &aips3->opacr2);
268 writel(0x00000000, &aips3->opacr3);
269 writel(0x00000000, &aips3->opacr4);
273 static void clear_ldo_ramp(void)
275 struct anatop_regs *anatop = (struct anatop_regs *)ANATOP_BASE_ADDR;
278 /* ROM may modify LDO ramp up time according to fuse setting, so in
279 * order to be in the safe side we neeed to reset these settings to
280 * match the reset value: 0'b00
282 reg = readl(&anatop->ana_misc2);
283 reg &= ~(0x3f << 24);
284 writel(reg, &anatop->ana_misc2);
288 * Set the PMU_REG_CORE register
290 * Set LDO_SOC/PU/ARM regulators to the specified millivolt level.
291 * Possible values are from 0.725V to 1.450V in steps of
294 static int set_ldo_voltage(enum ldo_reg ldo, u32 mv)
296 struct anatop_regs *anatop = (struct anatop_regs *)ANATOP_BASE_ADDR;
297 u32 val, step, old, reg = readl(&anatop->reg_core);
301 val = 0x00; /* Power gated off */
303 val = 0x1F; /* Power FET switched full on. No regulation */
305 val = (mv - 700) / 25;
323 old = (reg & (0x1F << shift)) >> shift;
324 step = abs(val - old);
328 reg = (reg & ~(0x1F << shift)) | (val << shift);
329 writel(reg, &anatop->reg_core);
332 * The LDO ramp-up is based on 64 clock cycles of 24 MHz = 2.6 us per
340 static u32 __data thermal_calib;
342 #define FACTOR0 10000000
343 #define FACTOR1 15976
344 #define FACTOR2 4297157
346 int raw_to_celsius(unsigned int raw, unsigned int raw_25c, unsigned int raw_hot,
347 unsigned int hot_temp)
351 if (raw_hot != 0 && hot_temp != 0) {
352 unsigned int raw_n40c, ratio;
354 ratio = ((raw_25c - raw_hot) * 100) / (hot_temp - 25);
355 raw_n40c = raw_25c + (13 * ratio) / 20;
357 temperature = (raw_n40c - raw) * 100 / ratio - 40;
359 temperature = TEMPERATURE_MIN;
361 u64 temp64 = FACTOR0;
364 * Derived from linear interpolation:
365 * slope = 0.4297157 - (0.0015976 * 25C fuse)
366 * slope = (FACTOR2 - FACTOR1 * n1) / FACTOR0
367 * (Nmeas - n1) / (Tmeas - t1) = slope
368 * We want to reduce this down to the minimum computation necessary
369 * for each temperature read. Also, we want Tmeas in millicelsius
370 * and we don't want to lose precision from integer division. So...
371 * Tmeas = (Nmeas - n1) / slope + t1
372 * milli_Tmeas = 1000 * (Nmeas - n1) / slope + 1000 * t1
373 * milli_Tmeas = -1000 * (n1 - Nmeas) / slope + 1000 * t1
374 * Let constant c1 = (-1000 / slope)
375 * milli_Tmeas = (n1 - Nmeas) * c1 + 1000 * t1
376 * Let constant c2 = n1 *c1 + 1000 * t1
377 * milli_Tmeas = c2 - Nmeas * c1
380 do_div(temp64, FACTOR1 * raw_25c - FACTOR2);
382 c2 = raw_25c * c1 + 1000 * 25;
383 temperature = (c2 - raw * c1) / 1000;
388 int read_cpu_temperature(void)
390 unsigned int reg, tmp, i;
391 unsigned int raw_25c, raw_hot, hot_temp;
393 struct anatop_regs *const anatop = (void *)ANATOP_BASE_ADDR;
394 struct mx6_ocotp_regs *const ocotp_regs = (void *)OCOTP_BASE_ADDR;
396 if (!thermal_calib) {
398 writel(1, &ocotp_regs->hw_ocotp_read_ctrl);
399 thermal_calib = readl(&ocotp_regs->hw_ocotp_ana1);
400 writel(0, &ocotp_regs->hw_ocotp_read_ctrl);
404 if (thermal_calib == 0 || thermal_calib == 0xffffffff)
405 return TEMPERATURE_MIN;
408 * [31:20] sensor value @ 25C
409 * [19:8] sensor value of hot
410 * [7:0] hot temperature value */
411 raw_25c = thermal_calib >> 20;
412 raw_hot = (thermal_calib & 0xfff00) >> 8;
413 hot_temp = thermal_calib & 0xff;
415 /* now we only using single measure, every time we measure
416 * the temperature, we will power on/off the anadig module
418 writel(BM_ANADIG_TEMPSENSE0_POWER_DOWN, &anatop->tempsense0_clr);
419 writel(BM_ANADIG_ANA_MISC0_REFTOP_SELBIASOFF, &anatop->ana_misc0_set);
421 /* write measure freq */
422 writel(327, &anatop->tempsense1);
423 writel(BM_ANADIG_TEMPSENSE0_MEASURE_TEMP, &anatop->tempsense0_clr);
424 writel(BM_ANADIG_TEMPSENSE0_FINISHED, &anatop->tempsense0_clr);
425 writel(BM_ANADIG_TEMPSENSE0_MEASURE_TEMP, &anatop->tempsense0_set);
427 /* average the temperature value over multiple readings */
428 for (i = 0; i < TEMP_AVG_COUNT; i++) {
432 while ((readl(&anatop->tempsense0) &
433 BM_ANADIG_TEMPSENSE0_FINISHED) == 0) {
438 if ((readl(&anatop->tempsense0) &
439 BM_ANADIG_TEMPSENSE0_FINISHED) == 0) {
441 printf("Failed to read temp sensor\n");
447 reg = (readl(&anatop->tempsense0) &
448 BM_ANADIG_TEMPSENSE0_TEMP_VALUE) >>
449 BP_ANADIG_TEMPSENSE0_TEMP_VALUE;
453 tmp = (tmp * i + reg) / (i + 1);
454 writel(BM_ANADIG_TEMPSENSE0_FINISHED,
455 &anatop->tempsense0_clr);
458 temperature = raw_to_celsius(tmp, raw_25c, raw_hot, hot_temp);
460 /* power down anatop thermal sensor */
461 writel(BM_ANADIG_TEMPSENSE0_POWER_DOWN, &anatop->tempsense0_set);
462 writel(BM_ANADIG_ANA_MISC0_REFTOP_SELBIASOFF, &anatop->ana_misc0_clr);
467 int check_cpu_temperature(int boot)
469 static int __data max_temp;
470 int boot_limit = getenv_ulong("max_boot_temp", 10, TEMPERATURE_HOT);
471 int tmp = read_cpu_temperature();
474 if (tmp < TEMPERATURE_MIN || tmp > TEMPERATURE_MAX) {
475 printf("Temperature: can't get valid data!\n");
480 if (tmp > boot_limit) {
481 printf("CPU is %d C, too hot, resetting...\n", tmp);
485 if (tmp > max_temp) {
486 if (tmp > boot_limit - TEMP_WARN_THRESHOLD)
487 printf("WARNING: CPU temperature %d C\n", tmp);
491 printf("Temperature: %d C, calibration data 0x%x\n",
493 while (tmp >= boot_limit) {
495 printf("CPU is %d C, too hot to boot, waiting...\n",
502 tmp = read_cpu_temperature();
503 if (tmp > boot_limit - TEMP_WARN_THRESHOLD && tmp != max_temp)
504 printf("WARNING: CPU temperature %d C\n", tmp);
511 static void imx_set_wdog_powerdown(bool enable)
513 struct wdog_regs *wdog1 = (struct wdog_regs *)WDOG1_BASE_ADDR;
514 struct wdog_regs *wdog2 = (struct wdog_regs *)WDOG2_BASE_ADDR;
515 struct wdog_regs *wdog3 = (struct wdog_regs *)WDOG3_BASE_ADDR;
517 if (is_cpu_type(MXC_CPU_MX6SX) || is_cpu_type(MXC_CPU_MX6UL))
518 writew(enable, &wdog3->wmcr);
520 /* Write to the PDE (Power Down Enable) bit */
521 writew(enable, &wdog1->wmcr);
522 writew(enable, &wdog2->wmcr);
525 static void set_ahb_rate(u32 val)
527 struct mxc_ccm_reg *mxc_ccm = (struct mxc_ccm_reg *)CCM_BASE_ADDR;
530 div = get_periph_clk() / val - 1;
531 reg = readl(&mxc_ccm->cbcdr);
533 writel((reg & (~MXC_CCM_CBCDR_AHB_PODF_MASK)) |
534 (div << MXC_CCM_CBCDR_AHB_PODF_OFFSET), &mxc_ccm->cbcdr);
537 static void clear_mmdc_ch_mask(void)
539 struct mxc_ccm_reg *mxc_ccm = (struct mxc_ccm_reg *)CCM_BASE_ADDR;
541 reg = readl(&mxc_ccm->ccdr);
543 /* Clear MMDC channel mask */
544 reg &= ~(MXC_CCM_CCDR_MMDC_CH1_HS_MASK | MXC_CCM_CCDR_MMDC_CH0_HS_MASK);
545 writel(reg, &mxc_ccm->ccdr);
548 static void init_bandgap(void)
550 struct anatop_regs *anatop = (struct anatop_regs *)ANATOP_BASE_ADDR;
552 * Ensure the bandgap has stabilized.
554 while (!(readl(&anatop->ana_misc0) & 0x80))
557 * For best noise performance of the analog blocks using the
558 * outputs of the bandgap, the reftop_selfbiasoff bit should
561 writel(BM_ANADIG_ANA_MISC0_REFTOP_SELBIASOFF, &anatop->ana_misc0_set);
564 #ifdef CONFIG_SOC_MX6SL
565 static void set_preclk_from_osc(void)
567 struct mxc_ccm_reg *mxc_ccm = (struct mxc_ccm_reg *)CCM_BASE_ADDR;
570 reg = readl(&mxc_ccm->cscmr1);
571 reg |= MXC_CCM_CSCMR1_PER_CLK_SEL_MASK;
572 writel(reg, &mxc_ccm->cscmr1);
576 #define SRC_SCR_WARM_RESET_ENABLE 0
578 static void init_src(void)
580 struct src *src_regs = (struct src *)SRC_BASE_ADDR;
584 * force warm reset sources to generate cold reset
585 * for a more reliable restart
587 val = readl(&src_regs->scr);
588 val &= ~(1 << SRC_SCR_WARM_RESET_ENABLE);
589 writel(val, &src_regs->scr);
592 int arch_cpu_init(void)
596 /* Need to clear MMDC_CHx_MASK to make warm reset work. */
597 clear_mmdc_ch_mask();
600 * Disable self-bias circuit in the analog bandap.
601 * The self-bias circuit is used by the bandgap during startup.
602 * This bit should be set after the bandgap has initialized.
607 * When low freq boot is enabled, ROM will not set AHB
608 * freq, so we need to ensure AHB freq is 132MHz in such
611 if (mxc_get_clock(MXC_ARM_CLK) == 396000000)
612 set_ahb_rate(132000000);
614 /* Set perclk to source from OSC 24MHz */
615 #if defined(CONFIG_SOC_MX6SL)
616 set_preclk_from_osc();
619 imx_set_wdog_powerdown(false); /* Disable PDE bit of WMCR register */
621 #ifdef CONFIG_VIDEO_IPUV3
622 gd->arch.ipu_hw_rev = IPUV3_HW_REV_IPUV3H;
624 #ifdef CONFIG_APBH_DMA
625 /* Timer is required for Initializing APBH DMA */
635 int board_postclk_init(void)
637 set_ldo_voltage(LDO_SOC, 1175); /* Set VDDSOC to 1.175V */
642 #ifndef CONFIG_SYS_DCACHE_OFF
643 void enable_caches(void)
645 #if defined(CONFIG_SYS_ARM_CACHE_WRITETHROUGH)
646 enum dcache_option option = DCACHE_WRITETHROUGH;
648 enum dcache_option option = DCACHE_WRITEBACK;
651 /* Avoid random hang when download by usb */
652 invalidate_dcache_all();
654 /* Enable D-cache. I-cache is already enabled in start.S */
657 /* Enable caching on OCRAM and ROM */
658 mmu_set_region_dcache_behaviour(ROMCP_ARB_BASE_ADDR,
661 mmu_set_region_dcache_behaviour(IRAM_BASE_ADDR,
667 #if defined(CONFIG_FEC_MXC)
668 void imx_get_mac_from_fuse(int dev_id, unsigned char *mac)
670 struct ocotp_regs *ocotp = (struct ocotp_regs *)OCOTP_BASE_ADDR;
671 struct fuse_bank *bank = &ocotp->bank[4];
672 struct fuse_bank4_regs *fuse =
673 (struct fuse_bank4_regs *)bank->fuse_regs;
675 u32 value = readl(&fuse->mac_addr_high);
676 mac[0] = (value >> 8);
679 value = readl(&fuse->mac_addr_low);
680 mac[2] = value >> 24;
681 mac[3] = value >> 16;
687 void boot_mode_apply(unsigned cfg_val)
690 struct src *psrc = (struct src *)SRC_BASE_ADDR;
691 writel(cfg_val, &psrc->gpr9);
692 reg = readl(&psrc->gpr10);
697 writel(reg, &psrc->gpr10);
700 * cfg_val will be used for
701 * Boot_cfg4[7:0]:Boot_cfg3[7:0]:Boot_cfg2[7:0]:Boot_cfg1[7:0]
702 * After reset, if GPR10[28] is 1, ROM will use GPR9[25:0]
703 * instead of SBMR1 to determine the boot device.
705 const struct boot_mode soc_boot_modes[] = {
706 {"normal", MAKE_CFGVAL(0x00, 0x00, 0x00, 0x00)},
707 /* reserved value should start rom usb */
708 {"usb", MAKE_CFGVAL(0x01, 0x00, 0x00, 0x00)},
709 {"sata", MAKE_CFGVAL(0x20, 0x00, 0x00, 0x00)},
710 {"ecspi1:0", MAKE_CFGVAL(0x30, 0x00, 0x00, 0x08)},
711 {"ecspi1:1", MAKE_CFGVAL(0x30, 0x00, 0x00, 0x18)},
712 {"ecspi1:2", MAKE_CFGVAL(0x30, 0x00, 0x00, 0x28)},
713 {"ecspi1:3", MAKE_CFGVAL(0x30, 0x00, 0x00, 0x38)},
714 /* 4 bit bus width */
715 {"esdhc1", MAKE_CFGVAL(0x40, 0x20, 0x00, 0x00)},
716 {"esdhc2", MAKE_CFGVAL(0x40, 0x28, 0x00, 0x00)},
717 {"esdhc3", MAKE_CFGVAL(0x40, 0x30, 0x00, 0x00)},
718 {"esdhc4", MAKE_CFGVAL(0x40, 0x38, 0x00, 0x00)},
724 struct anatop_regs *anatop = (struct anatop_regs *)ANATOP_BASE_ADDR;
725 struct mxc_ccm_reg *ccm = (struct mxc_ccm_reg *)CCM_BASE_ADDR;
728 u32 reg, periph1, periph2;
730 if (is_cpu_type(MXC_CPU_MX6SX) || is_cpu_type(MXC_CPU_MX6UL))
733 /* Due to hardware limitation, on MX6Q we need to gate/ungate all PFDs
734 * to make sure PFD is working right, otherwise, PFDs may
735 * not output clock after reset, MX6DL and MX6SL have added 396M pfd
736 * workaround in ROM code, as bus clock need it
739 mask480 = ANATOP_PFD_CLKGATE_MASK(0) |
740 ANATOP_PFD_CLKGATE_MASK(1) |
741 ANATOP_PFD_CLKGATE_MASK(2) |
742 ANATOP_PFD_CLKGATE_MASK(3);
743 mask528 = ANATOP_PFD_CLKGATE_MASK(1) |
744 ANATOP_PFD_CLKGATE_MASK(3);
746 reg = readl(&ccm->cbcmr);
747 periph2 = ((reg & MXC_CCM_CBCMR_PRE_PERIPH2_CLK_SEL_MASK)
748 >> MXC_CCM_CBCMR_PRE_PERIPH2_CLK_SEL_OFFSET);
749 periph1 = ((reg & MXC_CCM_CBCMR_PRE_PERIPH_CLK_SEL_MASK)
750 >> MXC_CCM_CBCMR_PRE_PERIPH_CLK_SEL_OFFSET);
752 /* Checking if PLL2 PFD0 or PLL2 PFD2 is using for periph clock */
753 if ((periph2 != 0x2) && (periph1 != 0x2))
754 mask528 |= ANATOP_PFD_CLKGATE_MASK(0);
756 if ((periph2 != 0x1) && (periph1 != 0x1) &&
757 (periph2 != 0x3) && (periph1 != 0x3))
758 mask528 |= ANATOP_PFD_CLKGATE_MASK(2);
760 writel(mask480, &anatop->pfd_480_set);
761 writel(mask528, &anatop->pfd_528_set);
762 writel(mask480, &anatop->pfd_480_clr);
763 writel(mask528, &anatop->pfd_528_clr);
766 #ifdef CONFIG_IMX_HDMI
767 void imx_enable_hdmi_phy(void)
769 struct hdmi_regs *hdmi = (struct hdmi_regs *)HDMI_ARB_BASE_ADDR;
771 reg = readb(&hdmi->phy_conf0);
772 reg |= HDMI_PHY_CONF0_PDZ_MASK;
773 writeb(reg, &hdmi->phy_conf0);
775 reg |= HDMI_PHY_CONF0_ENTMDS_MASK;
776 writeb(reg, &hdmi->phy_conf0);
778 reg |= HDMI_PHY_CONF0_GEN2_TXPWRON_MASK;
779 writeb(reg, &hdmi->phy_conf0);
780 writeb(HDMI_MC_PHYRSTZ_ASSERT, &hdmi->mc_phyrstz);
783 void imx_setup_hdmi(void)
785 struct mxc_ccm_reg *mxc_ccm = (struct mxc_ccm_reg *)CCM_BASE_ADDR;
786 struct hdmi_regs *hdmi = (struct hdmi_regs *)HDMI_ARB_BASE_ADDR;
789 /* Turn on HDMI PHY clock */
790 reg = readl(&mxc_ccm->CCGR2);
791 reg |= MXC_CCM_CCGR2_HDMI_TX_IAHBCLK_MASK|
792 MXC_CCM_CCGR2_HDMI_TX_ISFRCLK_MASK;
793 writel(reg, &mxc_ccm->CCGR2);
794 writeb(HDMI_MC_PHYRSTZ_DEASSERT, &hdmi->mc_phyrstz);
795 reg = readl(&mxc_ccm->chsccdr);
796 reg &= ~(MXC_CCM_CHSCCDR_IPU1_DI0_PRE_CLK_SEL_MASK|
797 MXC_CCM_CHSCCDR_IPU1_DI0_PODF_MASK|
798 MXC_CCM_CHSCCDR_IPU1_DI0_CLK_SEL_MASK);
799 reg |= (CHSCCDR_PODF_DIVIDE_BY_3
800 << MXC_CCM_CHSCCDR_IPU1_DI0_PODF_OFFSET)
801 |(CHSCCDR_IPU_PRE_CLK_540M_PFD
802 << MXC_CCM_CHSCCDR_IPU1_DI0_PRE_CLK_SEL_OFFSET);
803 writel(reg, &mxc_ccm->chsccdr);
807 #ifndef CONFIG_SYS_L2CACHE_OFF
808 #define IOMUXC_GPR11_L2CACHE_AS_OCRAM 0x00000002
809 void v7_outer_cache_enable(void)
811 struct pl310_regs *const pl310 = (struct pl310_regs *)L2_PL310_BASE;
816 * Set bit 22 in the auxiliary control register. If this bit
817 * is cleared, PL310 treats Normal Shared Non-cacheable
818 * accesses as Cacheable no-allocate.
820 setbits_le32(&pl310->pl310_aux_ctrl, L310_SHARED_ATT_OVERRIDE_ENABLE);
822 #if defined CONFIG_SOC_MX6SL
823 struct iomuxc *iomux = (struct iomuxc *)IOMUXC_BASE_ADDR;
824 val = readl(&iomux->gpr[11]);
825 if (val & IOMUXC_GPR11_L2CACHE_AS_OCRAM) {
826 /* L2 cache configured as OCRAM, reset it */
827 val &= ~IOMUXC_GPR11_L2CACHE_AS_OCRAM;
828 writel(val, &iomux->gpr[11]);
832 /* Must disable the L2 before changing the latency parameters */
833 clrbits_le32(&pl310->pl310_ctrl, L2X0_CTRL_EN);
835 writel(0x132, &pl310->pl310_tag_latency_ctrl);
836 writel(0x132, &pl310->pl310_data_latency_ctrl);
838 val = readl(&pl310->pl310_prefetch_ctrl);
840 /* Turn on the L2 I/D prefetch */
844 * The L2 cache controller(PL310) version on the i.MX6D/Q is r3p1-50rel0
845 * The L2 cache controller(PL310) version on the i.MX6DL/SOLO/SL is r3p2
846 * But according to ARM PL310 errata: 752271
847 * ID: 752271: Double linefill feature can cause data corruption
848 * Fault Status: Present in: r3p0, r3p1, r3p1-50rel0. Fixed in r3p2
849 * Workaround: The only workaround to this erratum is to disable the
850 * double linefill feature. This is the default behavior.
853 #ifndef CONFIG_SOC_MX6Q
856 writel(val, &pl310->pl310_prefetch_ctrl);
858 val = readl(&pl310->pl310_power_ctrl);
859 val |= L2X0_DYNAMIC_CLK_GATING_EN;
860 val |= L2X0_STNDBY_MODE_EN;
861 writel(val, &pl310->pl310_power_ctrl);
863 setbits_le32(&pl310->pl310_ctrl, L2X0_CTRL_EN);
866 void v7_outer_cache_disable(void)
868 struct pl310_regs *const pl310 = (struct pl310_regs *)L2_PL310_BASE;
870 clrbits_le32(&pl310->pl310_ctrl, L2X0_CTRL_EN);
872 #endif /* !CONFIG_SYS_L2CACHE_OFF */