2 * Driver for Atmel AT32 and AT91 SPI Controllers
4 * Copyright (C) 2006 Atmel Corporation
6 * This program is free software; you can redistribute it and/or modify
7 * it under the terms of the GNU General Public License version 2 as
8 * published by the Free Software Foundation.
11 #include <linux/kernel.h>
12 #include <linux/clk.h>
13 #include <linux/module.h>
14 #include <linux/platform_device.h>
15 #include <linux/delay.h>
16 #include <linux/dma-mapping.h>
17 #include <linux/dmaengine.h>
18 #include <linux/err.h>
19 #include <linux/interrupt.h>
20 #include <linux/spi/spi.h>
21 #include <linux/slab.h>
22 #include <linux/platform_data/atmel.h>
23 #include <linux/platform_data/dma-atmel.h>
27 #include <linux/gpio.h>
28 #include <linux/pinctrl/consumer.h>
29 #include <linux/pm_runtime.h>
31 /* SPI register offsets */
34 #define SPI_RDR 0x0008
35 #define SPI_TDR 0x000c
37 #define SPI_IER 0x0014
38 #define SPI_IDR 0x0018
39 #define SPI_IMR 0x001c
40 #define SPI_CSR0 0x0030
41 #define SPI_CSR1 0x0034
42 #define SPI_CSR2 0x0038
43 #define SPI_CSR3 0x003c
44 #define SPI_FMR 0x0040
45 #define SPI_FLR 0x0044
46 #define SPI_VERSION 0x00fc
47 #define SPI_RPR 0x0100
48 #define SPI_RCR 0x0104
49 #define SPI_TPR 0x0108
50 #define SPI_TCR 0x010c
51 #define SPI_RNPR 0x0110
52 #define SPI_RNCR 0x0114
53 #define SPI_TNPR 0x0118
54 #define SPI_TNCR 0x011c
55 #define SPI_PTCR 0x0120
56 #define SPI_PTSR 0x0124
59 #define SPI_SPIEN_OFFSET 0
60 #define SPI_SPIEN_SIZE 1
61 #define SPI_SPIDIS_OFFSET 1
62 #define SPI_SPIDIS_SIZE 1
63 #define SPI_SWRST_OFFSET 7
64 #define SPI_SWRST_SIZE 1
65 #define SPI_LASTXFER_OFFSET 24
66 #define SPI_LASTXFER_SIZE 1
67 #define SPI_TXFCLR_OFFSET 16
68 #define SPI_TXFCLR_SIZE 1
69 #define SPI_RXFCLR_OFFSET 17
70 #define SPI_RXFCLR_SIZE 1
71 #define SPI_FIFOEN_OFFSET 30
72 #define SPI_FIFOEN_SIZE 1
73 #define SPI_FIFODIS_OFFSET 31
74 #define SPI_FIFODIS_SIZE 1
77 #define SPI_MSTR_OFFSET 0
78 #define SPI_MSTR_SIZE 1
79 #define SPI_PS_OFFSET 1
81 #define SPI_PCSDEC_OFFSET 2
82 #define SPI_PCSDEC_SIZE 1
83 #define SPI_FDIV_OFFSET 3
84 #define SPI_FDIV_SIZE 1
85 #define SPI_MODFDIS_OFFSET 4
86 #define SPI_MODFDIS_SIZE 1
87 #define SPI_WDRBT_OFFSET 5
88 #define SPI_WDRBT_SIZE 1
89 #define SPI_LLB_OFFSET 7
90 #define SPI_LLB_SIZE 1
91 #define SPI_PCS_OFFSET 16
92 #define SPI_PCS_SIZE 4
93 #define SPI_DLYBCS_OFFSET 24
94 #define SPI_DLYBCS_SIZE 8
96 /* Bitfields in RDR */
97 #define SPI_RD_OFFSET 0
98 #define SPI_RD_SIZE 16
100 /* Bitfields in TDR */
101 #define SPI_TD_OFFSET 0
102 #define SPI_TD_SIZE 16
104 /* Bitfields in SR */
105 #define SPI_RDRF_OFFSET 0
106 #define SPI_RDRF_SIZE 1
107 #define SPI_TDRE_OFFSET 1
108 #define SPI_TDRE_SIZE 1
109 #define SPI_MODF_OFFSET 2
110 #define SPI_MODF_SIZE 1
111 #define SPI_OVRES_OFFSET 3
112 #define SPI_OVRES_SIZE 1
113 #define SPI_ENDRX_OFFSET 4
114 #define SPI_ENDRX_SIZE 1
115 #define SPI_ENDTX_OFFSET 5
116 #define SPI_ENDTX_SIZE 1
117 #define SPI_RXBUFF_OFFSET 6
118 #define SPI_RXBUFF_SIZE 1
119 #define SPI_TXBUFE_OFFSET 7
120 #define SPI_TXBUFE_SIZE 1
121 #define SPI_NSSR_OFFSET 8
122 #define SPI_NSSR_SIZE 1
123 #define SPI_TXEMPTY_OFFSET 9
124 #define SPI_TXEMPTY_SIZE 1
125 #define SPI_SPIENS_OFFSET 16
126 #define SPI_SPIENS_SIZE 1
127 #define SPI_TXFEF_OFFSET 24
128 #define SPI_TXFEF_SIZE 1
129 #define SPI_TXFFF_OFFSET 25
130 #define SPI_TXFFF_SIZE 1
131 #define SPI_TXFTHF_OFFSET 26
132 #define SPI_TXFTHF_SIZE 1
133 #define SPI_RXFEF_OFFSET 27
134 #define SPI_RXFEF_SIZE 1
135 #define SPI_RXFFF_OFFSET 28
136 #define SPI_RXFFF_SIZE 1
137 #define SPI_RXFTHF_OFFSET 29
138 #define SPI_RXFTHF_SIZE 1
139 #define SPI_TXFPTEF_OFFSET 30
140 #define SPI_TXFPTEF_SIZE 1
141 #define SPI_RXFPTEF_OFFSET 31
142 #define SPI_RXFPTEF_SIZE 1
144 /* Bitfields in CSR0 */
145 #define SPI_CPOL_OFFSET 0
146 #define SPI_CPOL_SIZE 1
147 #define SPI_NCPHA_OFFSET 1
148 #define SPI_NCPHA_SIZE 1
149 #define SPI_CSAAT_OFFSET 3
150 #define SPI_CSAAT_SIZE 1
151 #define SPI_BITS_OFFSET 4
152 #define SPI_BITS_SIZE 4
153 #define SPI_SCBR_OFFSET 8
154 #define SPI_SCBR_SIZE 8
155 #define SPI_DLYBS_OFFSET 16
156 #define SPI_DLYBS_SIZE 8
157 #define SPI_DLYBCT_OFFSET 24
158 #define SPI_DLYBCT_SIZE 8
160 /* Bitfields in RCR */
161 #define SPI_RXCTR_OFFSET 0
162 #define SPI_RXCTR_SIZE 16
164 /* Bitfields in TCR */
165 #define SPI_TXCTR_OFFSET 0
166 #define SPI_TXCTR_SIZE 16
168 /* Bitfields in RNCR */
169 #define SPI_RXNCR_OFFSET 0
170 #define SPI_RXNCR_SIZE 16
172 /* Bitfields in TNCR */
173 #define SPI_TXNCR_OFFSET 0
174 #define SPI_TXNCR_SIZE 16
176 /* Bitfields in PTCR */
177 #define SPI_RXTEN_OFFSET 0
178 #define SPI_RXTEN_SIZE 1
179 #define SPI_RXTDIS_OFFSET 1
180 #define SPI_RXTDIS_SIZE 1
181 #define SPI_TXTEN_OFFSET 8
182 #define SPI_TXTEN_SIZE 1
183 #define SPI_TXTDIS_OFFSET 9
184 #define SPI_TXTDIS_SIZE 1
186 /* Bitfields in FMR */
187 #define SPI_TXRDYM_OFFSET 0
188 #define SPI_TXRDYM_SIZE 2
189 #define SPI_RXRDYM_OFFSET 4
190 #define SPI_RXRDYM_SIZE 2
191 #define SPI_TXFTHRES_OFFSET 16
192 #define SPI_TXFTHRES_SIZE 6
193 #define SPI_RXFTHRES_OFFSET 24
194 #define SPI_RXFTHRES_SIZE 6
196 /* Bitfields in FLR */
197 #define SPI_TXFL_OFFSET 0
198 #define SPI_TXFL_SIZE 6
199 #define SPI_RXFL_OFFSET 16
200 #define SPI_RXFL_SIZE 6
202 /* Constants for BITS */
203 #define SPI_BITS_8_BPT 0
204 #define SPI_BITS_9_BPT 1
205 #define SPI_BITS_10_BPT 2
206 #define SPI_BITS_11_BPT 3
207 #define SPI_BITS_12_BPT 4
208 #define SPI_BITS_13_BPT 5
209 #define SPI_BITS_14_BPT 6
210 #define SPI_BITS_15_BPT 7
211 #define SPI_BITS_16_BPT 8
212 #define SPI_ONE_DATA 0
213 #define SPI_TWO_DATA 1
214 #define SPI_FOUR_DATA 2
216 /* Bit manipulation macros */
217 #define SPI_BIT(name) \
218 (1 << SPI_##name##_OFFSET)
219 #define SPI_BF(name, value) \
220 (((value) & ((1 << SPI_##name##_SIZE) - 1)) << SPI_##name##_OFFSET)
221 #define SPI_BFEXT(name, value) \
222 (((value) >> SPI_##name##_OFFSET) & ((1 << SPI_##name##_SIZE) - 1))
223 #define SPI_BFINS(name, value, old) \
224 (((old) & ~(((1 << SPI_##name##_SIZE) - 1) << SPI_##name##_OFFSET)) \
225 | SPI_BF(name, value))
227 /* Register access macros */
229 #define spi_readl(port, reg) \
230 __raw_readl((port)->regs + SPI_##reg)
231 #define spi_writel(port, reg, value) \
232 __raw_writel((value), (port)->regs + SPI_##reg)
234 #define spi_readw(port, reg) \
235 __raw_readw((port)->regs + SPI_##reg)
236 #define spi_writew(port, reg, value) \
237 __raw_writew((value), (port)->regs + SPI_##reg)
239 #define spi_readb(port, reg) \
240 __raw_readb((port)->regs + SPI_##reg)
241 #define spi_writeb(port, reg, value) \
242 __raw_writeb((value), (port)->regs + SPI_##reg)
244 #define spi_readl(port, reg) \
245 readl_relaxed((port)->regs + SPI_##reg)
246 #define spi_writel(port, reg, value) \
247 writel_relaxed((value), (port)->regs + SPI_##reg)
249 #define spi_readw(port, reg) \
250 readw_relaxed((port)->regs + SPI_##reg)
251 #define spi_writew(port, reg, value) \
252 writew_relaxed((value), (port)->regs + SPI_##reg)
254 #define spi_readb(port, reg) \
255 readb_relaxed((port)->regs + SPI_##reg)
256 #define spi_writeb(port, reg, value) \
257 writeb_relaxed((value), (port)->regs + SPI_##reg)
259 /* use PIO for small transfers, avoiding DMA setup/teardown overhead and
260 * cache operations; better heuristics consider wordsize and bitrate.
262 #define DMA_MIN_BYTES 16
264 #define SPI_DMA_TIMEOUT (msecs_to_jiffies(1000))
266 #define AUTOSUSPEND_TIMEOUT 2000
268 struct atmel_spi_dma {
269 struct dma_chan *chan_rx;
270 struct dma_chan *chan_tx;
271 struct scatterlist sgrx;
272 struct scatterlist sgtx;
273 struct dma_async_tx_descriptor *data_desc_rx;
274 struct dma_async_tx_descriptor *data_desc_tx;
276 struct at_dma_slave dma_slave;
279 struct atmel_spi_caps {
282 bool has_dma_support;
286 * The core SPI transfer engine just talks to a register bank to set up
287 * DMA transfers; transfer queue progress is driven by IRQs. The clock
288 * framework provides the base clock, subdivided for each spi_device.
298 struct platform_device *pdev;
300 struct spi_transfer *current_transfer;
301 int current_remaining_bytes;
304 struct completion xfer_completion;
308 dma_addr_t buffer_dma;
310 struct atmel_spi_caps caps;
316 struct atmel_spi_dma dma;
324 /* Controller-specific per-slave state */
325 struct atmel_spi_device {
326 unsigned int npcs_pin;
330 #define BUFFER_SIZE PAGE_SIZE
331 #define INVALID_DMA_ADDRESS 0xffffffff
334 * Version 2 of the SPI controller has
336 * - SPI_MR.DIV32 may become FDIV or must-be-zero (here: always zero)
337 * - SPI_SR.TXEMPTY, SPI_SR.NSSR (and corresponding irqs)
339 * - SPI_CSRx.SBCR allows faster clocking
341 static bool atmel_spi_is_v2(struct atmel_spi *as)
343 return as->caps.is_spi2;
347 * Earlier SPI controllers (e.g. on at91rm9200) have a design bug whereby
348 * they assume that spi slave device state will not change on deselect, so
349 * that automagic deselection is OK. ("NPCSx rises if no data is to be
350 * transmitted") Not so! Workaround uses nCSx pins as GPIOs; or newer
351 * controllers have CSAAT and friends.
353 * Since the CSAAT functionality is a bit weird on newer controllers as
354 * well, we use GPIO to control nCSx pins on all controllers, updating
355 * MR.PCS to avoid confusing the controller. Using GPIOs also lets us
356 * support active-high chipselects despite the controller's belief that
357 * only active-low devices/systems exists.
359 * However, at91rm9200 has a second erratum whereby nCS0 doesn't work
360 * right when driven with GPIO. ("Mode Fault does not allow more than one
361 * Master on Chip Select 0.") No workaround exists for that ... so for
362 * nCS0 on that chip, we (a) don't use the GPIO, (b) can't support CS_HIGH,
363 * and (c) will trigger that first erratum in some cases.
366 static void cs_activate(struct atmel_spi *as, struct spi_device *spi)
368 struct atmel_spi_device *asd = spi->controller_state;
369 unsigned active = spi->mode & SPI_CS_HIGH;
372 if (atmel_spi_is_v2(as)) {
373 spi_writel(as, CSR0 + 4 * spi->chip_select, asd->csr);
374 /* For the low SPI version, there is a issue that PDC transfer
375 * on CS1,2,3 needs SPI_CSR0.BITS config as SPI_CSR1,2,3.BITS
377 spi_writel(as, CSR0, asd->csr);
378 if (as->caps.has_wdrbt) {
380 SPI_BF(PCS, ~(0x01 << spi->chip_select))
386 SPI_BF(PCS, ~(0x01 << spi->chip_select))
391 mr = spi_readl(as, MR);
392 if (as->use_cs_gpios)
393 gpio_set_value(asd->npcs_pin, active);
395 u32 cpol = (spi->mode & SPI_CPOL) ? SPI_BIT(CPOL) : 0;
399 /* Make sure clock polarity is correct */
400 for (i = 0; i < spi->master->num_chipselect; i++) {
401 csr = spi_readl(as, CSR0 + 4 * i);
402 if ((csr ^ cpol) & SPI_BIT(CPOL))
403 spi_writel(as, CSR0 + 4 * i,
404 csr ^ SPI_BIT(CPOL));
407 mr = spi_readl(as, MR);
408 mr = SPI_BFINS(PCS, ~(1 << spi->chip_select), mr);
409 if (as->use_cs_gpios && spi->chip_select != 0)
410 gpio_set_value(asd->npcs_pin, active);
411 spi_writel(as, MR, mr);
414 dev_dbg(&spi->dev, "activate %u%s, mr %08x\n",
415 asd->npcs_pin, active ? " (high)" : "",
419 static void cs_deactivate(struct atmel_spi *as, struct spi_device *spi)
421 struct atmel_spi_device *asd = spi->controller_state;
422 unsigned active = spi->mode & SPI_CS_HIGH;
425 /* only deactivate *this* device; sometimes transfers to
426 * another device may be active when this routine is called.
428 mr = spi_readl(as, MR);
429 if (~SPI_BFEXT(PCS, mr) & (1 << spi->chip_select)) {
430 mr = SPI_BFINS(PCS, 0xf, mr);
431 spi_writel(as, MR, mr);
434 dev_dbg(&spi->dev, "DEactivate %u%s, mr %08x\n",
435 asd->npcs_pin, active ? " (low)" : "",
438 if (!as->use_cs_gpios)
439 spi_writel(as, CR, SPI_BIT(LASTXFER));
440 else if (atmel_spi_is_v2(as) || spi->chip_select != 0)
441 gpio_set_value(asd->npcs_pin, !active);
444 static void atmel_spi_lock(struct atmel_spi *as) __acquires(&as->lock)
446 spin_lock_irqsave(&as->lock, as->flags);
449 static void atmel_spi_unlock(struct atmel_spi *as) __releases(&as->lock)
451 spin_unlock_irqrestore(&as->lock, as->flags);
454 static inline bool atmel_spi_use_dma(struct atmel_spi *as,
455 struct spi_transfer *xfer)
457 return as->use_dma && xfer->len >= DMA_MIN_BYTES;
460 static int atmel_spi_dma_slave_config(struct atmel_spi *as,
461 struct dma_slave_config *slave_config,
466 if (bits_per_word > 8) {
467 slave_config->dst_addr_width = DMA_SLAVE_BUSWIDTH_2_BYTES;
468 slave_config->src_addr_width = DMA_SLAVE_BUSWIDTH_2_BYTES;
470 slave_config->dst_addr_width = DMA_SLAVE_BUSWIDTH_1_BYTE;
471 slave_config->src_addr_width = DMA_SLAVE_BUSWIDTH_1_BYTE;
474 slave_config->dst_addr = (dma_addr_t)as->phybase + SPI_TDR;
475 slave_config->src_addr = (dma_addr_t)as->phybase + SPI_RDR;
476 slave_config->src_maxburst = 1;
477 slave_config->dst_maxburst = 1;
478 slave_config->device_fc = false;
481 * This driver uses fixed peripheral select mode (PS bit set to '0' in
482 * the Mode Register).
483 * So according to the datasheet, when FIFOs are available (and
484 * enabled), the Transmit FIFO operates in Multiple Data Mode.
485 * In this mode, up to 2 data, not 4, can be written into the Transmit
486 * Data Register in a single access.
487 * However, the first data has to be written into the lowest 16 bits and
488 * the second data into the highest 16 bits of the Transmit
489 * Data Register. For 8bit data (the most frequent case), it would
490 * require to rework tx_buf so each data would actualy fit 16 bits.
491 * So we'd rather write only one data at the time. Hence the transmit
492 * path works the same whether FIFOs are available (and enabled) or not.
494 slave_config->direction = DMA_MEM_TO_DEV;
495 if (dmaengine_slave_config(as->dma.chan_tx, slave_config)) {
496 dev_err(&as->pdev->dev,
497 "failed to configure tx dma channel\n");
502 * This driver configures the spi controller for master mode (MSTR bit
503 * set to '1' in the Mode Register).
504 * So according to the datasheet, when FIFOs are available (and
505 * enabled), the Receive FIFO operates in Single Data Mode.
506 * So the receive path works the same whether FIFOs are available (and
509 slave_config->direction = DMA_DEV_TO_MEM;
510 if (dmaengine_slave_config(as->dma.chan_rx, slave_config)) {
511 dev_err(&as->pdev->dev,
512 "failed to configure rx dma channel\n");
519 static int atmel_spi_configure_dma(struct atmel_spi *as)
521 struct dma_slave_config slave_config;
522 struct device *dev = &as->pdev->dev;
527 dma_cap_set(DMA_SLAVE, mask);
529 as->dma.chan_tx = dma_request_slave_channel_reason(dev, "tx");
530 if (IS_ERR(as->dma.chan_tx)) {
531 err = PTR_ERR(as->dma.chan_tx);
532 if (err == -EPROBE_DEFER) {
533 dev_warn(dev, "no DMA channel available at the moment\n");
537 "DMA TX channel not available, SPI unable to use DMA\n");
543 * No reason to check EPROBE_DEFER here since we have already requested
544 * tx channel. If it fails here, it's for another reason.
546 as->dma.chan_rx = dma_request_slave_channel(dev, "rx");
548 if (!as->dma.chan_rx) {
550 "DMA RX channel not available, SPI unable to use DMA\n");
555 err = atmel_spi_dma_slave_config(as, &slave_config, 8);
559 dev_info(&as->pdev->dev,
560 "Using %s (tx) and %s (rx) for DMA transfers\n",
561 dma_chan_name(as->dma.chan_tx),
562 dma_chan_name(as->dma.chan_rx));
566 dma_release_channel(as->dma.chan_rx);
567 if (!IS_ERR(as->dma.chan_tx))
568 dma_release_channel(as->dma.chan_tx);
572 static void atmel_spi_stop_dma(struct atmel_spi *as)
575 dmaengine_terminate_all(as->dma.chan_rx);
577 dmaengine_terminate_all(as->dma.chan_tx);
580 static void atmel_spi_release_dma(struct atmel_spi *as)
583 dma_release_channel(as->dma.chan_rx);
585 dma_release_channel(as->dma.chan_tx);
588 /* This function is called by the DMA driver from tasklet context */
589 static void dma_callback(void *data)
591 struct spi_master *master = data;
592 struct atmel_spi *as = spi_master_get_devdata(master);
594 complete(&as->xfer_completion);
598 * Next transfer using PIO without FIFO.
600 static void atmel_spi_next_xfer_single(struct spi_master *master,
601 struct spi_transfer *xfer)
603 struct atmel_spi *as = spi_master_get_devdata(master);
604 unsigned long xfer_pos = xfer->len - as->current_remaining_bytes;
606 dev_vdbg(master->dev.parent, "atmel_spi_next_xfer_pio\n");
608 /* Make sure data is not remaining in RDR */
610 while (spi_readl(as, SR) & SPI_BIT(RDRF)) {
616 if (xfer->bits_per_word > 8)
617 spi_writel(as, TDR, *(u16 *)(xfer->tx_buf + xfer_pos));
619 spi_writel(as, TDR, *(u8 *)(xfer->tx_buf + xfer_pos));
621 spi_writel(as, TDR, 0);
624 dev_dbg(master->dev.parent,
625 " start pio xfer %p: len %u tx %p rx %p bitpw %d\n",
626 xfer, xfer->len, xfer->tx_buf, xfer->rx_buf,
627 xfer->bits_per_word);
629 /* Enable relevant interrupts */
630 spi_writel(as, IER, SPI_BIT(RDRF) | SPI_BIT(OVRES));
634 * Next transfer using PIO with FIFO.
636 static void atmel_spi_next_xfer_fifo(struct spi_master *master,
637 struct spi_transfer *xfer)
639 struct atmel_spi *as = spi_master_get_devdata(master);
640 u32 current_remaining_data, num_data;
641 u32 offset = xfer->len - as->current_remaining_bytes;
642 const u16 *words = (const u16 *)((u8 *)xfer->tx_buf + offset);
643 const u8 *bytes = (const u8 *)((u8 *)xfer->tx_buf + offset);
647 dev_vdbg(master->dev.parent, "atmel_spi_next_xfer_fifo\n");
649 /* Compute the number of data to transfer in the current iteration */
650 current_remaining_data = ((xfer->bits_per_word > 8) ?
651 ((u32)as->current_remaining_bytes >> 1) :
652 (u32)as->current_remaining_bytes);
653 num_data = min(current_remaining_data, as->fifo_size);
655 /* Flush RX and TX FIFOs */
656 spi_writel(as, CR, SPI_BIT(RXFCLR) | SPI_BIT(TXFCLR));
657 while (spi_readl(as, FLR))
660 /* Set RX FIFO Threshold to the number of data to transfer */
661 fifomr = spi_readl(as, FMR);
662 spi_writel(as, FMR, SPI_BFINS(RXFTHRES, num_data, fifomr));
664 /* Clear FIFO flags in the Status Register, especially RXFTHF */
665 (void)spi_readl(as, SR);
668 while (num_data >= 2) {
670 if (xfer->bits_per_word > 8) {
682 spi_writel(as, TDR, (td1 << 16) | td0);
688 if (xfer->bits_per_word > 8)
696 spi_writew(as, TDR, td0);
700 dev_dbg(master->dev.parent,
701 " start fifo xfer %p: len %u tx %p rx %p bitpw %d\n",
702 xfer, xfer->len, xfer->tx_buf, xfer->rx_buf,
703 xfer->bits_per_word);
706 * Enable RX FIFO Threshold Flag interrupt to be notified about
707 * transfer completion.
709 spi_writel(as, IER, SPI_BIT(RXFTHF) | SPI_BIT(OVRES));
713 * Next transfer using PIO.
715 static void atmel_spi_next_xfer_pio(struct spi_master *master,
716 struct spi_transfer *xfer)
718 struct atmel_spi *as = spi_master_get_devdata(master);
721 atmel_spi_next_xfer_fifo(master, xfer);
723 atmel_spi_next_xfer_single(master, xfer);
727 * Submit next transfer for DMA.
729 static int atmel_spi_next_xfer_dma_submit(struct spi_master *master,
730 struct spi_transfer *xfer,
733 struct atmel_spi *as = spi_master_get_devdata(master);
734 struct dma_chan *rxchan = as->dma.chan_rx;
735 struct dma_chan *txchan = as->dma.chan_tx;
736 struct dma_async_tx_descriptor *rxdesc;
737 struct dma_async_tx_descriptor *txdesc;
738 struct dma_slave_config slave_config;
742 dev_vdbg(master->dev.parent, "atmel_spi_next_xfer_dma_submit\n");
744 /* Check that the channels are available */
745 if (!rxchan || !txchan)
748 /* release lock for DMA operations */
749 atmel_spi_unlock(as);
751 /* prepare the RX dma transfer */
752 sg_init_table(&as->dma.sgrx, 1);
754 as->dma.sgrx.dma_address = xfer->rx_dma + xfer->len - *plen;
756 as->dma.sgrx.dma_address = as->buffer_dma;
757 if (len > BUFFER_SIZE)
761 /* prepare the TX dma transfer */
762 sg_init_table(&as->dma.sgtx, 1);
764 as->dma.sgtx.dma_address = xfer->tx_dma + xfer->len - *plen;
766 as->dma.sgtx.dma_address = as->buffer_dma;
767 if (len > BUFFER_SIZE)
769 memset(as->buffer, 0, len);
772 sg_dma_len(&as->dma.sgtx) = len;
773 sg_dma_len(&as->dma.sgrx) = len;
777 if (atmel_spi_dma_slave_config(as, &slave_config, 8))
780 /* Send both scatterlists */
781 rxdesc = dmaengine_prep_slave_sg(rxchan, &as->dma.sgrx, 1,
783 DMA_PREP_INTERRUPT | DMA_CTRL_ACK);
787 txdesc = dmaengine_prep_slave_sg(txchan, &as->dma.sgtx, 1,
789 DMA_PREP_INTERRUPT | DMA_CTRL_ACK);
793 dev_dbg(master->dev.parent,
794 " start dma xfer %p: len %u tx %p/%08llx rx %p/%08llx\n",
795 xfer, xfer->len, xfer->tx_buf, (unsigned long long)xfer->tx_dma,
796 xfer->rx_buf, (unsigned long long)xfer->rx_dma);
798 /* Enable relevant interrupts */
799 spi_writel(as, IER, SPI_BIT(OVRES));
801 /* Put the callback on the RX transfer only, that should finish last */
802 rxdesc->callback = dma_callback;
803 rxdesc->callback_param = master;
805 /* Submit and fire RX and TX with TX last so we're ready to read! */
806 cookie = rxdesc->tx_submit(rxdesc);
807 if (dma_submit_error(cookie))
809 cookie = txdesc->tx_submit(txdesc);
810 if (dma_submit_error(cookie))
812 rxchan->device->device_issue_pending(rxchan);
813 txchan->device->device_issue_pending(txchan);
820 spi_writel(as, IDR, SPI_BIT(OVRES));
821 atmel_spi_stop_dma(as);
827 static void atmel_spi_next_xfer_data(struct spi_master *master,
828 struct spi_transfer *xfer,
833 struct atmel_spi *as = spi_master_get_devdata(master);
836 /* use scratch buffer only when rx or tx data is unspecified */
838 *rx_dma = xfer->rx_dma + xfer->len - *plen;
840 *rx_dma = as->buffer_dma;
841 if (len > BUFFER_SIZE)
846 *tx_dma = xfer->tx_dma + xfer->len - *plen;
848 *tx_dma = as->buffer_dma;
849 if (len > BUFFER_SIZE)
851 memset(as->buffer, 0, len);
852 dma_sync_single_for_device(&as->pdev->dev,
853 as->buffer_dma, len, DMA_TO_DEVICE);
859 static int atmel_spi_set_xfer_speed(struct atmel_spi *as,
860 struct spi_device *spi,
861 struct spi_transfer *xfer)
864 unsigned long bus_hz;
866 /* v1 chips start out at half the peripheral bus speed. */
867 bus_hz = clk_get_rate(as->clk);
868 if (!atmel_spi_is_v2(as))
872 * Calculate the lowest divider that satisfies the
873 * constraint, assuming div32/fdiv/mbz == 0.
876 scbr = DIV_ROUND_UP(bus_hz, xfer->speed_hz);
879 * This can happend if max_speed is null.
880 * In this case, we set the lowest possible speed
885 * If the resulting divider doesn't fit into the
886 * register bitfield, we can't satisfy the constraint.
888 if (scbr >= (1 << SPI_SCBR_SIZE)) {
890 "setup: %d Hz too slow, scbr %u; min %ld Hz\n",
891 xfer->speed_hz, scbr, bus_hz/255);
896 "setup: %d Hz too high, scbr %u; max %ld Hz\n",
897 xfer->speed_hz, scbr, bus_hz);
900 csr = spi_readl(as, CSR0 + 4 * spi->chip_select);
901 csr = SPI_BFINS(SCBR, scbr, csr);
902 spi_writel(as, CSR0 + 4 * spi->chip_select, csr);
908 * Submit next transfer for PDC.
909 * lock is held, spi irq is blocked
911 static void atmel_spi_pdc_next_xfer(struct spi_master *master,
912 struct spi_message *msg,
913 struct spi_transfer *xfer)
915 struct atmel_spi *as = spi_master_get_devdata(master);
917 dma_addr_t tx_dma, rx_dma;
919 spi_writel(as, PTCR, SPI_BIT(RXTDIS) | SPI_BIT(TXTDIS));
921 len = as->current_remaining_bytes;
922 atmel_spi_next_xfer_data(master, xfer, &tx_dma, &rx_dma, &len);
923 as->current_remaining_bytes -= len;
925 spi_writel(as, RPR, rx_dma);
926 spi_writel(as, TPR, tx_dma);
928 if (msg->spi->bits_per_word > 8)
930 spi_writel(as, RCR, len);
931 spi_writel(as, TCR, len);
933 dev_dbg(&msg->spi->dev,
934 " start xfer %p: len %u tx %p/%08llx rx %p/%08llx\n",
935 xfer, xfer->len, xfer->tx_buf,
936 (unsigned long long)xfer->tx_dma, xfer->rx_buf,
937 (unsigned long long)xfer->rx_dma);
939 if (as->current_remaining_bytes) {
940 len = as->current_remaining_bytes;
941 atmel_spi_next_xfer_data(master, xfer, &tx_dma, &rx_dma, &len);
942 as->current_remaining_bytes -= len;
944 spi_writel(as, RNPR, rx_dma);
945 spi_writel(as, TNPR, tx_dma);
947 if (msg->spi->bits_per_word > 8)
949 spi_writel(as, RNCR, len);
950 spi_writel(as, TNCR, len);
952 dev_dbg(&msg->spi->dev,
953 " next xfer %p: len %u tx %p/%08llx rx %p/%08llx\n",
954 xfer, xfer->len, xfer->tx_buf,
955 (unsigned long long)xfer->tx_dma, xfer->rx_buf,
956 (unsigned long long)xfer->rx_dma);
959 /* REVISIT: We're waiting for RXBUFF before we start the next
960 * transfer because we need to handle some difficult timing
961 * issues otherwise. If we wait for TXBUFE in one transfer and
962 * then starts waiting for RXBUFF in the next, it's difficult
963 * to tell the difference between the RXBUFF interrupt we're
964 * actually waiting for and the RXBUFF interrupt of the
967 * It should be doable, though. Just not now...
969 spi_writel(as, IER, SPI_BIT(RXBUFF) | SPI_BIT(OVRES));
970 spi_writel(as, PTCR, SPI_BIT(TXTEN) | SPI_BIT(RXTEN));
974 * For DMA, tx_buf/tx_dma have the same relationship as rx_buf/rx_dma:
975 * - The buffer is either valid for CPU access, else NULL
976 * - If the buffer is valid, so is its DMA address
978 * This driver manages the dma address unless message->is_dma_mapped.
981 atmel_spi_dma_map_xfer(struct atmel_spi *as, struct spi_transfer *xfer)
983 struct device *dev = &as->pdev->dev;
985 xfer->tx_dma = xfer->rx_dma = INVALID_DMA_ADDRESS;
987 /* tx_buf is a const void* where we need a void * for the dma
989 void *nonconst_tx = (void *)xfer->tx_buf;
991 xfer->tx_dma = dma_map_single(dev,
992 nonconst_tx, xfer->len,
994 if (dma_mapping_error(dev, xfer->tx_dma))
998 xfer->rx_dma = dma_map_single(dev,
999 xfer->rx_buf, xfer->len,
1001 if (dma_mapping_error(dev, xfer->rx_dma)) {
1003 dma_unmap_single(dev,
1004 xfer->tx_dma, xfer->len,
1012 static void atmel_spi_dma_unmap_xfer(struct spi_master *master,
1013 struct spi_transfer *xfer)
1015 if (xfer->tx_dma != INVALID_DMA_ADDRESS)
1016 dma_unmap_single(master->dev.parent, xfer->tx_dma,
1017 xfer->len, DMA_TO_DEVICE);
1018 if (xfer->rx_dma != INVALID_DMA_ADDRESS)
1019 dma_unmap_single(master->dev.parent, xfer->rx_dma,
1020 xfer->len, DMA_FROM_DEVICE);
1023 static void atmel_spi_disable_pdc_transfer(struct atmel_spi *as)
1025 spi_writel(as, PTCR, SPI_BIT(RXTDIS) | SPI_BIT(TXTDIS));
1029 atmel_spi_pump_single_data(struct atmel_spi *as, struct spi_transfer *xfer)
1033 unsigned long xfer_pos = xfer->len - as->current_remaining_bytes;
1036 if (xfer->bits_per_word > 8) {
1037 rxp16 = (u16 *)(((u8 *)xfer->rx_buf) + xfer_pos);
1038 *rxp16 = spi_readl(as, RDR);
1040 rxp = ((u8 *)xfer->rx_buf) + xfer_pos;
1041 *rxp = spi_readl(as, RDR);
1046 if (xfer->bits_per_word > 8) {
1047 if (as->current_remaining_bytes > 2)
1048 as->current_remaining_bytes -= 2;
1050 as->current_remaining_bytes = 0;
1052 as->current_remaining_bytes--;
1057 atmel_spi_pump_fifo_data(struct atmel_spi *as, struct spi_transfer *xfer)
1059 u32 fifolr = spi_readl(as, FLR);
1060 u32 num_bytes, num_data = SPI_BFEXT(RXFL, fifolr);
1061 u32 offset = xfer->len - as->current_remaining_bytes;
1062 u16 *words = (u16 *)((u8 *)xfer->rx_buf + offset);
1063 u8 *bytes = (u8 *)((u8 *)xfer->rx_buf + offset);
1064 u16 rd; /* RD field is the lowest 16 bits of RDR */
1066 /* Update the number of remaining bytes to transfer */
1067 num_bytes = ((xfer->bits_per_word > 8) ?
1071 if (as->current_remaining_bytes > num_bytes)
1072 as->current_remaining_bytes -= num_bytes;
1074 as->current_remaining_bytes = 0;
1076 /* Handle odd number of bytes when data are more than 8bit width */
1077 if (xfer->bits_per_word > 8)
1078 as->current_remaining_bytes &= ~0x1;
1082 rd = spi_readl(as, RDR);
1084 if (xfer->bits_per_word > 8)
1095 * Must update "current_remaining_bytes" to keep track of data
1099 atmel_spi_pump_pio_data(struct atmel_spi *as, struct spi_transfer *xfer)
1102 atmel_spi_pump_fifo_data(as, xfer);
1104 atmel_spi_pump_single_data(as, xfer);
1109 * No need for locking in this Interrupt handler: done_status is the
1110 * only information modified.
1113 atmel_spi_pio_interrupt(int irq, void *dev_id)
1115 struct spi_master *master = dev_id;
1116 struct atmel_spi *as = spi_master_get_devdata(master);
1117 u32 status, pending, imr;
1118 struct spi_transfer *xfer;
1121 imr = spi_readl(as, IMR);
1122 status = spi_readl(as, SR);
1123 pending = status & imr;
1125 if (pending & SPI_BIT(OVRES)) {
1127 spi_writel(as, IDR, SPI_BIT(OVRES));
1128 dev_warn(master->dev.parent, "overrun\n");
1131 * When we get an overrun, we disregard the current
1132 * transfer. Data will not be copied back from any
1133 * bounce buffer and msg->actual_len will not be
1134 * updated with the last xfer.
1136 * We will also not process any remaning transfers in
1139 as->done_status = -EIO;
1142 /* Clear any overrun happening while cleaning up */
1145 complete(&as->xfer_completion);
1147 } else if (pending & (SPI_BIT(RDRF) | SPI_BIT(RXFTHF))) {
1150 if (as->current_remaining_bytes) {
1152 xfer = as->current_transfer;
1153 atmel_spi_pump_pio_data(as, xfer);
1154 if (!as->current_remaining_bytes)
1155 spi_writel(as, IDR, pending);
1157 complete(&as->xfer_completion);
1160 atmel_spi_unlock(as);
1162 WARN_ONCE(pending, "IRQ not handled, pending = %x\n", pending);
1164 spi_writel(as, IDR, pending);
1171 atmel_spi_pdc_interrupt(int irq, void *dev_id)
1173 struct spi_master *master = dev_id;
1174 struct atmel_spi *as = spi_master_get_devdata(master);
1175 u32 status, pending, imr;
1178 imr = spi_readl(as, IMR);
1179 status = spi_readl(as, SR);
1180 pending = status & imr;
1182 if (pending & SPI_BIT(OVRES)) {
1186 spi_writel(as, IDR, (SPI_BIT(RXBUFF) | SPI_BIT(ENDRX)
1189 /* Clear any overrun happening while cleaning up */
1192 as->done_status = -EIO;
1194 complete(&as->xfer_completion);
1196 } else if (pending & (SPI_BIT(RXBUFF) | SPI_BIT(ENDRX))) {
1199 spi_writel(as, IDR, pending);
1201 complete(&as->xfer_completion);
1207 static int atmel_spi_setup(struct spi_device *spi)
1209 struct atmel_spi *as;
1210 struct atmel_spi_device *asd;
1212 unsigned int bits = spi->bits_per_word;
1213 unsigned int npcs_pin;
1216 as = spi_master_get_devdata(spi->master);
1218 /* see notes above re chipselect */
1219 if (!atmel_spi_is_v2(as)
1220 && spi->chip_select == 0
1221 && (spi->mode & SPI_CS_HIGH)) {
1222 dev_dbg(&spi->dev, "setup: can't be active-high\n");
1226 csr = SPI_BF(BITS, bits - 8);
1227 if (spi->mode & SPI_CPOL)
1228 csr |= SPI_BIT(CPOL);
1229 if (!(spi->mode & SPI_CPHA))
1230 csr |= SPI_BIT(NCPHA);
1231 if (!as->use_cs_gpios)
1232 csr |= SPI_BIT(CSAAT);
1234 /* DLYBS is mostly irrelevant since we manage chipselect using GPIOs.
1236 * DLYBCT would add delays between words, slowing down transfers.
1237 * It could potentially be useful to cope with DMA bottlenecks, but
1238 * in those cases it's probably best to just use a lower bitrate.
1240 csr |= SPI_BF(DLYBS, 0);
1241 csr |= SPI_BF(DLYBCT, 0);
1243 /* chipselect must have been muxed as GPIO (e.g. in board setup) */
1244 npcs_pin = (unsigned long)spi->controller_data;
1246 if (!as->use_cs_gpios)
1247 npcs_pin = spi->chip_select;
1248 else if (gpio_is_valid(spi->cs_gpio))
1249 npcs_pin = spi->cs_gpio;
1251 asd = spi->controller_state;
1253 asd = kzalloc(sizeof(struct atmel_spi_device), GFP_KERNEL);
1257 if (as->use_cs_gpios) {
1258 ret = gpio_request(npcs_pin, dev_name(&spi->dev));
1264 gpio_direction_output(npcs_pin,
1265 !(spi->mode & SPI_CS_HIGH));
1268 asd->npcs_pin = npcs_pin;
1269 spi->controller_state = asd;
1275 "setup: bpw %u mode 0x%x -> csr%d %08x\n",
1276 bits, spi->mode, spi->chip_select, csr);
1278 if (!atmel_spi_is_v2(as))
1279 spi_writel(as, CSR0 + 4 * spi->chip_select, csr);
1284 static int atmel_spi_one_transfer(struct spi_master *master,
1285 struct spi_message *msg,
1286 struct spi_transfer *xfer)
1288 struct atmel_spi *as;
1289 struct spi_device *spi = msg->spi;
1292 struct atmel_spi_device *asd;
1295 unsigned long dma_timeout;
1297 as = spi_master_get_devdata(master);
1299 if (!(xfer->tx_buf || xfer->rx_buf) && xfer->len) {
1300 dev_dbg(&spi->dev, "missing rx or tx buf\n");
1304 if (xfer->bits_per_word) {
1305 asd = spi->controller_state;
1306 bits = (asd->csr >> 4) & 0xf;
1307 if (bits != xfer->bits_per_word - 8) {
1309 "you can't yet change bits_per_word in transfers\n");
1310 return -ENOPROTOOPT;
1315 * DMA map early, for performance (empties dcache ASAP) and
1316 * better fault reporting.
1318 if ((!msg->is_dma_mapped)
1319 && (atmel_spi_use_dma(as, xfer) || as->use_pdc)) {
1320 if (atmel_spi_dma_map_xfer(as, xfer) < 0)
1324 atmel_spi_set_xfer_speed(as, msg->spi, xfer);
1326 as->done_status = 0;
1327 as->current_transfer = xfer;
1328 as->current_remaining_bytes = xfer->len;
1329 while (as->current_remaining_bytes) {
1330 reinit_completion(&as->xfer_completion);
1333 atmel_spi_pdc_next_xfer(master, msg, xfer);
1334 } else if (atmel_spi_use_dma(as, xfer)) {
1335 len = as->current_remaining_bytes;
1336 ret = atmel_spi_next_xfer_dma_submit(master,
1340 "unable to use DMA, fallback to PIO\n");
1341 atmel_spi_next_xfer_pio(master, xfer);
1343 as->current_remaining_bytes -= len;
1344 if (as->current_remaining_bytes < 0)
1345 as->current_remaining_bytes = 0;
1348 atmel_spi_next_xfer_pio(master, xfer);
1351 /* interrupts are disabled, so free the lock for schedule */
1352 atmel_spi_unlock(as);
1353 dma_timeout = wait_for_completion_timeout(&as->xfer_completion,
1356 if (WARN_ON(dma_timeout == 0)) {
1357 dev_err(&spi->dev, "spi transfer timeout\n");
1358 as->done_status = -EIO;
1361 if (as->done_status)
1365 if (as->done_status) {
1367 dev_warn(master->dev.parent,
1368 "overrun (%u/%u remaining)\n",
1369 spi_readl(as, TCR), spi_readl(as, RCR));
1372 * Clean up DMA registers and make sure the data
1373 * registers are empty.
1375 spi_writel(as, RNCR, 0);
1376 spi_writel(as, TNCR, 0);
1377 spi_writel(as, RCR, 0);
1378 spi_writel(as, TCR, 0);
1379 for (timeout = 1000; timeout; timeout--)
1380 if (spi_readl(as, SR) & SPI_BIT(TXEMPTY))
1383 dev_warn(master->dev.parent,
1384 "timeout waiting for TXEMPTY");
1385 while (spi_readl(as, SR) & SPI_BIT(RDRF))
1388 /* Clear any overrun happening while cleaning up */
1391 } else if (atmel_spi_use_dma(as, xfer)) {
1392 atmel_spi_stop_dma(as);
1395 if (!msg->is_dma_mapped
1396 && (atmel_spi_use_dma(as, xfer) || as->use_pdc))
1397 atmel_spi_dma_unmap_xfer(master, xfer);
1402 /* only update length if no error */
1403 msg->actual_length += xfer->len;
1406 if (!msg->is_dma_mapped
1407 && (atmel_spi_use_dma(as, xfer) || as->use_pdc))
1408 atmel_spi_dma_unmap_xfer(master, xfer);
1410 if (xfer->delay_usecs)
1411 udelay(xfer->delay_usecs);
1413 if (xfer->cs_change) {
1414 if (list_is_last(&xfer->transfer_list,
1418 as->cs_active = !as->cs_active;
1420 cs_activate(as, msg->spi);
1422 cs_deactivate(as, msg->spi);
1429 static int atmel_spi_transfer_one_message(struct spi_master *master,
1430 struct spi_message *msg)
1432 struct atmel_spi *as;
1433 struct spi_transfer *xfer;
1434 struct spi_device *spi = msg->spi;
1437 as = spi_master_get_devdata(master);
1439 dev_dbg(&spi->dev, "new message %p submitted for %s\n",
1440 msg, dev_name(&spi->dev));
1443 cs_activate(as, spi);
1445 as->cs_active = true;
1446 as->keep_cs = false;
1449 msg->actual_length = 0;
1451 list_for_each_entry(xfer, &msg->transfers, transfer_list) {
1452 ret = atmel_spi_one_transfer(master, msg, xfer);
1458 atmel_spi_disable_pdc_transfer(as);
1460 list_for_each_entry(xfer, &msg->transfers, transfer_list) {
1462 " xfer %p: len %u tx %p/%pad rx %p/%pad\n",
1464 xfer->tx_buf, &xfer->tx_dma,
1465 xfer->rx_buf, &xfer->rx_dma);
1470 cs_deactivate(as, msg->spi);
1472 atmel_spi_unlock(as);
1474 msg->status = as->done_status;
1475 spi_finalize_current_message(spi->master);
1480 static void atmel_spi_cleanup(struct spi_device *spi)
1482 struct atmel_spi_device *asd = spi->controller_state;
1483 unsigned gpio = (unsigned long) spi->controller_data;
1488 spi->controller_state = NULL;
1493 static inline unsigned int atmel_get_version(struct atmel_spi *as)
1495 return spi_readl(as, VERSION) & 0x00000fff;
1498 static void atmel_get_caps(struct atmel_spi *as)
1500 unsigned int version;
1502 version = atmel_get_version(as);
1503 dev_info(&as->pdev->dev, "version: 0x%x\n", version);
1505 as->caps.is_spi2 = version > 0x121;
1506 as->caps.has_wdrbt = version >= 0x210;
1507 as->caps.has_dma_support = version >= 0x212;
1510 /*-------------------------------------------------------------------------*/
1512 static int atmel_spi_probe(struct platform_device *pdev)
1514 struct resource *regs;
1518 struct spi_master *master;
1519 struct atmel_spi *as;
1521 /* Select default pin state */
1522 pinctrl_pm_select_default_state(&pdev->dev);
1524 regs = platform_get_resource(pdev, IORESOURCE_MEM, 0);
1528 irq = platform_get_irq(pdev, 0);
1532 clk = devm_clk_get(&pdev->dev, "spi_clk");
1534 return PTR_ERR(clk);
1536 /* setup spi core then atmel-specific driver state */
1538 master = spi_alloc_master(&pdev->dev, sizeof(*as));
1542 /* the spi->mode bits understood by this driver: */
1543 master->mode_bits = SPI_CPOL | SPI_CPHA | SPI_CS_HIGH;
1544 master->bits_per_word_mask = SPI_BPW_RANGE_MASK(8, 16);
1545 master->dev.of_node = pdev->dev.of_node;
1546 master->bus_num = pdev->id;
1547 master->num_chipselect = master->dev.of_node ? 0 : 4;
1548 master->setup = atmel_spi_setup;
1549 master->transfer_one_message = atmel_spi_transfer_one_message;
1550 master->cleanup = atmel_spi_cleanup;
1551 master->auto_runtime_pm = true;
1552 platform_set_drvdata(pdev, master);
1554 as = spi_master_get_devdata(master);
1557 * Scratch buffer is used for throwaway rx and tx data.
1558 * It's coherent to minimize dcache pollution.
1560 as->buffer = dma_alloc_coherent(&pdev->dev, BUFFER_SIZE,
1561 &as->buffer_dma, GFP_KERNEL);
1565 spin_lock_init(&as->lock);
1568 as->regs = devm_ioremap_resource(&pdev->dev, regs);
1569 if (IS_ERR(as->regs)) {
1570 ret = PTR_ERR(as->regs);
1571 goto out_free_buffer;
1573 as->phybase = regs->start;
1577 init_completion(&as->xfer_completion);
1581 as->use_cs_gpios = true;
1582 if (atmel_spi_is_v2(as) &&
1583 !of_get_property(pdev->dev.of_node, "cs-gpios", NULL)) {
1584 as->use_cs_gpios = false;
1585 master->num_chipselect = 4;
1588 as->use_dma = false;
1589 as->use_pdc = false;
1590 if (as->caps.has_dma_support) {
1591 ret = atmel_spi_configure_dma(as);
1594 else if (ret == -EPROBE_DEFER)
1600 if (as->caps.has_dma_support && !as->use_dma)
1601 dev_info(&pdev->dev, "Atmel SPI Controller using PIO only\n");
1604 ret = devm_request_irq(&pdev->dev, irq, atmel_spi_pdc_interrupt,
1605 0, dev_name(&pdev->dev), master);
1607 ret = devm_request_irq(&pdev->dev, irq, atmel_spi_pio_interrupt,
1608 0, dev_name(&pdev->dev), master);
1611 goto out_unmap_regs;
1613 /* Initialize the hardware */
1614 ret = clk_prepare_enable(clk);
1617 spi_writel(as, CR, SPI_BIT(SWRST));
1618 spi_writel(as, CR, SPI_BIT(SWRST)); /* AT91SAM9263 Rev B workaround */
1619 if (as->caps.has_wdrbt) {
1620 spi_writel(as, MR, SPI_BIT(WDRBT) | SPI_BIT(MODFDIS)
1623 spi_writel(as, MR, SPI_BIT(MSTR) | SPI_BIT(MODFDIS));
1627 spi_writel(as, PTCR, SPI_BIT(RXTDIS) | SPI_BIT(TXTDIS));
1628 spi_writel(as, CR, SPI_BIT(SPIEN));
1631 if (!of_property_read_u32(pdev->dev.of_node, "atmel,fifo-size",
1633 dev_info(&pdev->dev, "Using FIFO (%u data)\n", as->fifo_size);
1634 spi_writel(as, CR, SPI_BIT(FIFOEN));
1638 dev_info(&pdev->dev, "Atmel SPI Controller at 0x%08lx (irq %d)\n",
1639 (unsigned long)regs->start, irq);
1641 pm_runtime_set_autosuspend_delay(&pdev->dev, AUTOSUSPEND_TIMEOUT);
1642 pm_runtime_use_autosuspend(&pdev->dev);
1643 pm_runtime_set_active(&pdev->dev);
1644 pm_runtime_enable(&pdev->dev);
1646 ret = devm_spi_register_master(&pdev->dev, master);
1653 pm_runtime_disable(&pdev->dev);
1654 pm_runtime_set_suspended(&pdev->dev);
1657 atmel_spi_release_dma(as);
1659 spi_writel(as, CR, SPI_BIT(SWRST));
1660 spi_writel(as, CR, SPI_BIT(SWRST)); /* AT91SAM9263 Rev B workaround */
1661 clk_disable_unprepare(clk);
1665 dma_free_coherent(&pdev->dev, BUFFER_SIZE, as->buffer,
1668 spi_master_put(master);
1672 static int atmel_spi_remove(struct platform_device *pdev)
1674 struct spi_master *master = platform_get_drvdata(pdev);
1675 struct atmel_spi *as = spi_master_get_devdata(master);
1677 pm_runtime_get_sync(&pdev->dev);
1679 /* reset the hardware and block queue progress */
1680 spin_lock_irq(&as->lock);
1682 atmel_spi_stop_dma(as);
1683 atmel_spi_release_dma(as);
1686 spi_writel(as, CR, SPI_BIT(SWRST));
1687 spi_writel(as, CR, SPI_BIT(SWRST)); /* AT91SAM9263 Rev B workaround */
1689 spin_unlock_irq(&as->lock);
1691 dma_free_coherent(&pdev->dev, BUFFER_SIZE, as->buffer,
1694 clk_disable_unprepare(as->clk);
1696 pm_runtime_put_noidle(&pdev->dev);
1697 pm_runtime_disable(&pdev->dev);
1703 static int atmel_spi_runtime_suspend(struct device *dev)
1705 struct spi_master *master = dev_get_drvdata(dev);
1706 struct atmel_spi *as = spi_master_get_devdata(master);
1708 clk_disable_unprepare(as->clk);
1709 pinctrl_pm_select_sleep_state(dev);
1714 static int atmel_spi_runtime_resume(struct device *dev)
1716 struct spi_master *master = dev_get_drvdata(dev);
1717 struct atmel_spi *as = spi_master_get_devdata(master);
1719 pinctrl_pm_select_default_state(dev);
1721 return clk_prepare_enable(as->clk);
1724 static int atmel_spi_suspend(struct device *dev)
1726 struct spi_master *master = dev_get_drvdata(dev);
1729 /* Stop the queue running */
1730 ret = spi_master_suspend(master);
1732 dev_warn(dev, "cannot suspend master\n");
1736 if (!pm_runtime_suspended(dev))
1737 atmel_spi_runtime_suspend(dev);
1742 static int atmel_spi_resume(struct device *dev)
1744 struct spi_master *master = dev_get_drvdata(dev);
1747 if (!pm_runtime_suspended(dev)) {
1748 ret = atmel_spi_runtime_resume(dev);
1753 /* Start the queue running */
1754 ret = spi_master_resume(master);
1756 dev_err(dev, "problem starting queue (%d)\n", ret);
1761 static const struct dev_pm_ops atmel_spi_pm_ops = {
1762 SET_SYSTEM_SLEEP_PM_OPS(atmel_spi_suspend, atmel_spi_resume)
1763 SET_RUNTIME_PM_OPS(atmel_spi_runtime_suspend,
1764 atmel_spi_runtime_resume, NULL)
1766 #define ATMEL_SPI_PM_OPS (&atmel_spi_pm_ops)
1768 #define ATMEL_SPI_PM_OPS NULL
1771 #if defined(CONFIG_OF)
1772 static const struct of_device_id atmel_spi_dt_ids[] = {
1773 { .compatible = "atmel,at91rm9200-spi" },
1777 MODULE_DEVICE_TABLE(of, atmel_spi_dt_ids);
1780 static struct platform_driver atmel_spi_driver = {
1782 .name = "atmel_spi",
1783 .pm = ATMEL_SPI_PM_OPS,
1784 .of_match_table = of_match_ptr(atmel_spi_dt_ids),
1786 .probe = atmel_spi_probe,
1787 .remove = atmel_spi_remove,
1789 module_platform_driver(atmel_spi_driver);
1791 MODULE_DESCRIPTION("Atmel AT32/AT91 SPI Controller driver");
1792 MODULE_AUTHOR("Haavard Skinnemoen (Atmel)");
1793 MODULE_LICENSE("GPL");
1794 MODULE_ALIAS("platform:atmel_spi");