drivers/staging/wilc1000/wilc_wlan_if.h

   1 /* ////////////////////////////////////////////////////////////////////////// */
   2 /*  */
   3 /* Copyright (c) Atmel Corporation.  All rights reserved. */
   4 /*  */
   5 /* Module Name:  wilc_wlan_if.h */
   6 /*  */
   7 /*  */
   8 /* ///////////////////////////////////////////////////////////////////////// */
   9
  10
  11 #ifndef WILC_WLAN_IF_H
  12 #define WILC_WLAN_IF_H
  13
  14 /*bug 3887: [AP] Allow Management frames to be passed to the host*/
  15 #define WILC_AP_EXTERNAL_MLME
  16 #define WILC_P2P
  17 #define TCP_ENHANCEMENTS
  18 /* #define MEMORY_STATIC */
  19 /* #define WILC_FULLY_HOSTING_AP */
  20 /* #define USE_OLD_SPI_SW */
  21
  22
  23 #include "wilc_oswrapper.h"
  24 #include "linux_wlan_common.h"
  25
  26
  27 /********************************************
  28  *
  29  *      Debug Flags
  30  *
  31  ********************************************/
  32
  33 #define N_INIT          0x00000001
  34 #define N_ERR           0x00000002
  35 #define N_TXQ           0x00000004
  36 #define N_INTR          0x00000008
  37 #define N_RXQ           0x00000010
  38
  39 /********************************************
  40  *
  41  *      Host Interface Defines
  42  *
  43  ********************************************/
  44
  45 #define HIF_SDIO           (0)
  46 #define HIF_SPI            BIT(0)
  47 #define HIF_SDIO_GPIO_IRQ  BIT(2)
  48
  49
  50 /********************************************
  51  *
  52  *      Tx/Rx Buffer Size Defines
  53  *
  54  ********************************************/
  55
  56 #define CE_TX_BUFFER_SIZE (64 * 1024)
  57 #define CE_RX_BUFFER_SIZE (384 * 1024)
  58
  59 /********************************************
  60  *
  61  *      Wlan Interface Defines
  62  *
  63  ********************************************/
  64
  65 typedef struct {
  66         uint32_t read_write: 1;
  67         uint32_t function: 3;
  68         uint32_t raw: 1;
  69         uint32_t address: 17;
  70         uint32_t data: 8;
  71 } sdio_cmd52_t;
  72
  73 typedef struct {
  74         /* struct { */
  75         uint32_t read_write: 1;
  76         uint32_t function: 3;
  77         uint32_t block_mode: 1;
  78         uint32_t increment: 1;
  79         uint32_t address: 17;
  80         uint32_t count: 9;
  81         /* } bit; */
  82         uint8_t *buffer;
  83         uint32_t block_size;
  84 } sdio_cmd53_t;
  85
  86 typedef struct {
  87         void (*os_sleep)(uint32_t);
  88         void (*os_atomic_sleep)(uint32_t);
  89         void (*os_debug)(uint8_t *);
  90         void *(*os_malloc)(uint32_t);
  91         void *(*os_malloc_atomic)(uint32_t);
  92         void (*os_free)(void *);
  93         void (*os_lock)(void *);
  94         void (*os_unlock)(void *);
  95         int (*os_wait)(void *, u32);
  96         void (*os_signal)(void *);
  97         void (*os_enter_cs)(void *);
  98         void (*os_leave_cs)(void *);
  99
 100         /*Added by Amr - BugID_4720*/
 101         void (*os_spin_lock)(void *, unsigned long *);
 102         void (*os_spin_unlock)(void *, unsigned long *);
 103
 104 } wilc_wlan_os_func_t;
 105
 106 typedef struct {
 107         int io_type;
 108         int (*io_init)(void *);
 109         void (*io_deinit)(void *);
 110         union {
 111                 struct {
 112                         int (*sdio_cmd52)(sdio_cmd52_t *);
 113                         int (*sdio_cmd53)(sdio_cmd53_t *);
 114                         int (*sdio_set_max_speed)(void);
 115                         int (*sdio_set_default_speed)(void);
 116                 } sdio;
 117                 struct {
 118                         int (*spi_max_speed)(void);
 119                         int (*spi_tx)(uint8_t *, uint32_t);
 120                         int (*spi_rx)(uint8_t *, uint32_t);
 121                         int (*spi_trx)(uint8_t *, uint8_t *, uint32_t);
 122                 } spi;
 123         } u;
 124 } wilc_wlan_io_func_t;
 125
 126 typedef struct {
 127         void (*rx_indicate)(uint8_t *, uint32_t, uint32_t);
 128         void (*rx_complete)(void);
 129 } wilc_wlan_net_func_t;
 130
 131 typedef struct {
 132         void (*mac_indicate)(int);
 133 } wilc_wlan_indicate_func_t;
 134 #define WILC_MAC_INDICATE_STATUS                0x1
 135 #define WILC_MAC_STATUS_INIT    -1
 136 #define WILC_MAC_STATUS_READY 0
 137 #define WILC_MAC_STATUS_CONNECT 1
 138
 139 #define WILC_MAC_INDICATE_SCAN          0x2
 140
 141 typedef struct {
 142         void *os_private;
 143
 144         void *hif_critical_section;
 145
 146         uint32_t tx_buffer_size;
 147         void *txq_critical_section;
 148
 149         /*Added by Amr - BugID_4720*/
 150         void *txq_add_to_head_critical_section;
 151         void *txq_spin_lock;
 152
 153         void *txq_wait_event;
 154
 155 #if defined(MEMORY_STATIC)
 156         uint32_t rx_buffer_size;
 157 #endif
 158         void *rxq_critical_section;
 159         void *rxq_wait_event;
 160
 161         void *cfg_wait_event;
 162 } wilc_wlan_os_context_t;
 163
 164 typedef struct {
 165         wilc_wlan_os_context_t os_context;
 166         wilc_wlan_os_func_t os_func;
 167         wilc_wlan_io_func_t io_func;
 168         wilc_wlan_net_func_t net_func;
 169         wilc_wlan_indicate_func_t indicate_func;
 170 } wilc_wlan_inp_t;
 171
 172 struct tx_complete_data {
 173         #ifdef WILC_FULLY_HOSTING_AP
 174         struct tx_complete_data *next;
 175         #endif
 176         int size;
 177         void *buff;
 178         uint8_t *pBssid;
 179         struct sk_buff *skb;
 180 };
 181
 182
 183 typedef void (*wilc_tx_complete_func_t)(void *, int);
 184
 185 #define WILC_TX_ERR_NO_BUF (-2)
 186
 187 typedef struct {
 188         int (*wlan_firmware_download)(const uint8_t *, uint32_t);
 189         int (*wlan_start)(void);
 190         int (*wlan_stop)(void);
 191         int (*wlan_add_to_tx_que)(void *, uint8_t *, uint32_t, wilc_tx_complete_func_t);
 192         int (*wlan_handle_tx_que)(uint32_t *);
 193         void (*wlan_handle_rx_que)(void);
 194         void (*wlan_handle_rx_isr)(void);
 195         void (*wlan_cleanup)(void);
 196         int (*wlan_cfg_set)(int, uint32_t, uint8_t *, uint32_t, int, uint32_t);
 197         int (*wlan_cfg_get)(int, uint32_t, int, uint32_t);
 198         int (*wlan_cfg_get_value)(uint32_t, uint8_t *, uint32_t);
 199         /*Bug3959: transmitting mgmt frames received from host*/
 200         #if defined(WILC_AP_EXTERNAL_MLME) || defined(WILC_P2P)
 201         int (*wlan_add_mgmt_to_tx_que)(void *, uint8_t *, uint32_t, wilc_tx_complete_func_t);
 202
 203         #ifdef WILC_FULLY_HOSTING_AP
 204         int (*wlan_add_data_to_tx_que)(void *, uint8_t *, uint32_t, wilc_tx_complete_func_t);
 205         #endif
 206
 207         #endif
 208 } wilc_wlan_oup_t;
 209
 210 /********************************************
 211  *
 212  *      Wlan Configuration ID
 213  *
 214  ********************************************/
 215
 216 #define MAX_SSID_LEN            33
 217 #define MAX_RATES_SUPPORTED     12
 218
 219 #define INFINITE_SLEEP_TIME             ((u32)0xFFFFFFFF)
 220
 221 #ifdef WILC_PARSE_SCAN_IN_HOST
 222 typedef enum {
 223         SUPP_RATES_IE = 1,
 224         EXT_SUPP_RATES_IE = 50,
 225         HT_CAPABILITY_IE = 45,
 226         RSN_IE = 48,
 227         WPA_IE = 221,
 228         WMM_IE = 221,
 229         #ifdef WILC_P2P
 230         P2P_IE = 221,
 231         #endif
 232 } BEACON_IE;
 233 #endif
 234 typedef enum {
 235         INFRASTRUCTURE = 0,
 236         INDEPENDENT,
 237         AP,
 238 } BSSTYPE_T;
 239
 240 typedef enum {
 241         RATE_AUTO = 0,
 242         RATE_1MB = 1,
 243         RATE_2MB = 2,
 244         RATE_5MB = 5,
 245         RATE_6MB = 6,
 246         RATE_9MB = 9,
 247         RATE_11MB = 11,
 248         RATE_12MB = 12,
 249         RATE_18MB = 18,
 250         RATE_24MB = 24,
 251         RATE_26MB = 36,
 252         RATE_48MB = 48,
 253         RATE_54MB = 54
 254 } TX_RATE_T;
 255
 256 typedef enum {
 257         B_ONLY_MODE = 0,                                /* basic rate: 1, 2 Mbps, otherwise: 5, 11 Mbps */
 258         G_ONLY_MODE,                                    /* basic rate: 6, 12, 24 Mbps, otherwise: 9, 18, 36, 48, 54 Mbps */
 259         G_MIXED_11B_1_MODE,             /* basic rate: 1, 2, 5.5, 11 Mbps, otherwise: all on */
 260         G_MIXED_11B_2_MODE,             /* basic rate: 1, 2, 5, 11, 6, 12, 24 Mbps, otherwise: all on */
 261 } G_OPERATING_MODE_T;
 262
 263 typedef enum {
 264         G_SHORT_PREAMBLE = 0,   /* Short Preamble          */
 265         G_LONG_PREAMBLE  = 1,           /* Long Preamble           */
 266         G_AUTO_PREAMBLE  = 2,           /* Auto Preamble Selection */
 267 } G_PREAMBLE_T;
 268
 269 #define MAC_CONNECTED    1
 270 #define MAC_DISCONNECTED 0
 271
 272 /*bug3819: */
 273 #define SCAN_DONE               TRUE
 274 typedef enum {
 275         PASSIVE_SCAN = 0,
 276         ACTIVE_SCAN  = 1,
 277 } SCANTYPE_T;
 278
 279 typedef enum {
 280         NO_POWERSAVE     = 0,
 281         MIN_FAST_PS      = 1,
 282         MAX_FAST_PS      = 2,
 283         MIN_PSPOLL_PS    = 3,
 284         MAX_PSPOLL_PS    = 4
 285 } USER_PS_MODE_T;
 286
 287 typedef enum {
 288         CHIP_WAKEDUP                    = 0,
 289         CHIP_SLEEPING_AUTO      = 1,
 290         CHIP_SLEEPING_MANUAL  = 2
 291 } CHIP_PS_STATE_T;
 292
 293 typedef enum {
 294         ACQUIRE_ONLY                             = 0,
 295         ACQUIRE_AND_WAKEUP      = 1,
 296 } BUS_ACQUIRE_T;
 297
 298 typedef enum {
 299         RELEASE_ONLY                            = 0,
 300         RELEASE_ALLOW_SLEEP             = 1,
 301 } BUS_RELEASE_T;
 302
 303 typedef enum {
 304         NO_SECURITY = 0,
 305         WEP_40 = 0x3,
 306         WEP_104 = 0x7,
 307         WPA_AES = 0x29,
 308         WPA_TKIP = 0x49,
 309         WPA_AES_TKIP = 0x69,            /* Aes or Tkip */
 310         WPA2_AES = 0x31,
 311         WPA2_TKIP = 0x51,
 312         WPA2_AES_TKIP = 0x71,   /* Aes or Tkip */
 313 } SECURITY_T;
 314
 315 typedef enum {
 316         OPEN_SYSTEM     = 1,
 317         SHARED_KEY      = 2,
 318         ANY                             = 3,
 319         IEEE8021 = 5
 320 } AUTHTYPE_T;
 321
 322 typedef enum {
 323         SITE_SURVEY_1CH    = 0,
 324         SITE_SURVEY_ALL_CH = 1,
 325         SITE_SURVEY_OFF    = 2
 326 } SITE_SURVEY_T;
 327
 328 typedef enum {
 329         NORMAL_ACK = 0,
 330         NO_ACK,
 331 } ACK_POLICY_T;
 332
 333 typedef enum {
 334         DONT_RESET = 0,
 335         DO_RESET   = 1,
 336         NO_REQUEST = 2,
 337 } RESET_REQ_T;
 338
 339 typedef enum {
 340         REKEY_DISABLE = 1,
 341         REKEY_TIME_BASE,
 342         REKEY_PKT_BASE,
 343         REKEY_TIME_PKT_BASE
 344 } RSNA_REKEY_POLICY_T;
 345
 346 typedef enum {
 347         FILTER_NO       = 0x00,
 348         FILTER_AP_ONLY  = 0x01,
 349         FILTER_STA_ONLY = 0x02
 350 } SCAN_CLASS_FITLER_T;
 351
 352 typedef enum {
 353         PRI_HIGH_RSSI    = 0x00,
 354         PRI_LOW_RSSI     = 0x04,
 355         PRI_DETECT       = 0x08
 356 } SCAN_PRI_T;
 357
 358 typedef enum {
 359         CH_FILTER_OFF    = 0x00,
 360         CH_FILTER_ON     = 0x10
 361 } CH_FILTER_T;
 362
 363 typedef enum {
 364         AUTO_PROT = 0,  /* Auto */
 365         NO_PROT,                        /* Do not use any protection       */
 366         ERP_PROT,                       /* Protect all ERP frame exchanges */
 367         HT_PROT,                        /* Protect all HT frame exchanges  */
 368         GF_PROT,                        /* Protect all GF frame exchanges  */
 369 } N_PROTECTION_MODE_T;
 370
 371 typedef enum {
 372         G_SELF_CTS_PROT,
 373         G_RTS_CTS_PROT,
 374 } G_PROTECTION_MODE_T;
 375
 376 typedef enum {
 377         HT_MIXED_MODE = 1,
 378         HT_ONLY_20MHZ_MODE,
 379         HT_ONLY_20_40MHZ_MODE,
 380 } N_OPERATING_MODE_T;
 381
 382 typedef enum {
 383         NO_DETECT             = 0,
 384         DETECT_ONLY           = 1,
 385         DETECT_PROTECT        = 2,
 386         DETECT_PROTECT_REPORT = 3,
 387 } N_OBSS_DETECTION_T;
 388
 389 typedef enum {
 390         RTS_CTS_NONHT_PROT = 0,                 /* RTS-CTS at non-HT rate      */
 391         FIRST_FRAME_NONHT_PROT,         /* First frame at non-HT rate  */
 392         LSIG_TXOP_PROT,                                 /* LSIG TXOP Protection        */
 393         FIRST_FRAME_MIXED_PROT,         /* First frame at Mixed format */
 394 } N_PROTECTION_TYPE_T;
 395
 396 typedef enum {
 397         STATIC_MODE   = 1,
 398         DYNAMIC_MODE  = 2,
 399         MIMO_MODE     = 3,              /* power save disable */
 400 } N_SMPS_MODE_T;
 401
 402 typedef enum {
 403         DISABLE_SELF_CTS,
 404         ENABLE_SELF_CTS,
 405         DISABLE_TX_ABORT,
 406         ENABLE_TX_ABORT,
 407         HW_TRIGGER_ABORT,
 408         SW_TRIGGER_ABORT,
 409 } TX_ABORT_OPTION_T;
 410
 411 typedef enum {
 412         WID_CHAR     = 0,
 413         WID_SHORT    = 1,
 414         WID_INT      = 2,
 415         WID_STR      = 3,
 416         WID_BIN_DATA = 4,
 417         WID_BIN   = 5,
 418         WID_IP    = 6,
 419         WID_ADR   = 7,
 420         WID_UNDEF = 8,
 421         WID_TYPE_FORCE_32BIT  = 0xFFFFFFFF
 422
 423 } WID_TYPE_T, tenuWIDtype;
 424
 425 typedef enum {
 426         WID_NIL                            = 0xffff,
 427
 428
 429         /*  BSS Type                                                                                                                                                                            */
 430         /*  --------------------------------------------------------------      */
 431         /*  Configuration :  Infrastructure    Independent   Access Point                                                                               */
 432         /*  Values to set :         0               1            2                                                                                                                      */
 433         /*  --------------------------------------------------------------      */
 434         WID_BSS_TYPE                                            = 0x0000,
 435
 436         /*  Transmit Rate                                                                                                                                                                       */
 437         /*  --------------------------------------------------------------      */
 438         /*  Configuration :  1  2  5.5  11  6  9  12  18  24  36  48  54                                                                                */
 439         /*  Values to set :  1  2  5  11  6  9  12  18  24  36  48  54                                                                                  */
 440         /*  --------------------------------------------------------------      */
 441         WID_CURRENT_TX_RATE                     = 0x0001,
 442
 443         /*  Channel                                                                                                                                                                                                     */
 444         /*  -------------------------------------------------------------------         */
 445         /*  Configuration(g) :  1  2  3  4  5  6  7  8   9   10  11  12  13  14                                                                                         */
 446         /*  Values to set    :  1  2  3  4  5  6  7  8   9   10  11  12  13  14                                                                                         */
 447         /*  --------------------------------------------------------------------        */
 448         WID_CURRENT_CHANNEL                     = 0x0002,
 449
 450         /*  Preamble                                                                                                                                                                            */
 451         /*  --------------------------------------------------------------      */
 452         /*  Configuration :    short    long   Auto                                                                                                                             */
 453         /*  Values to set :       0         1         2                                                                                                                                 */
 454         /*  --------------------------------------------------------------      */
 455         WID_PREAMBLE                                            = 0x0003,
 456
 457         /*  11g operating mode (ignored if 11g not present)                                                                                                     */
 458         /*  --------------------------------------------------------------      */
 459         /*  Configuration :   HighPerf  Compat(RSet #1) Compat(RSet #2)                                                                 */
 460         /*  Values to set :          1               2               3                                                                                                                  */
 461         /*  --------------------------------------------------------------      */
 462         WID_11G_OPERATING_MODE            = 0x0004,
 463
 464         /*  Mac status (response only)                                                                                                                                                                  */
 465         /*  --------------------------------------------------------------      */
 466         /*  Configuration :   disconnect  connect                                                                                                                                               */
 467         /*  Values to get :          0               1                                                                                                                                          */
 468         /*  --------------------------------------------------------------      */
 469         WID_STATUS                                              = 0x0005,
 470
 471         /*  Scan type                                                                                                                                                                           */
 472         /*  --------------------------------------------------------------      */
 473         /*  Configuration :   Passive Scanning   Active Scanning                                                                                        */
 474         /*  Values to set :                  0                 1                                                                                                                                */
 475         /*  --------------------------------------------------------------      */
 476         WID_SCAN_TYPE                      = 0x0007,
 477
 478         /*  Key Id (WEP default key Id)                                                                                                                                                 */
 479         /*  --------------------------------------------------------------      */
 480         /*  Configuration :   Any value between 0 to 3                                                                                                                  */
 481         /*  Values to set :     Same value. Default is 0                                                                                                                                */
 482         /*  --------------------------------------------------------------      */
 483         WID_KEY_ID                         = 0x0009,
 484
 485         /*  QoS Enable                                                                                                                                                                          */
 486         /*  --------------------------------------------------------------      */
 487         /*  Configuration :   QoS Disable   WMM Enable                                                                                                          */
 488         /*  Values to set :   0             1                                                                                                                                                   */
 489         /*  --------------------------------------------------------------      */
 490         WID_QOS_ENABLE                     = 0x000A,
 491
 492         /*  Power Management                                                                                                                                                                    */
 493         /*  ------------------------------------------------------------------  */
 494         /*  Configuration :   NO_POWERSAVE   MIN_POWERSAVE   MAX_POWERSAVE                                              */
 495         /*  Values to set :   0              1               2                                                                                                                                  */
 496         /*  ------------------------------------------------------------------   */
 497         WID_POWER_MANAGEMENT               = 0x000B,
 498
 499         /*  WEP/802 11I Configuration                                            */
 500         /*  ------------------------------------------------------------------  */
 501         /*  Configuration : Disable WP40 WP104 WPA-AES WPA-TKIP RSN-AES RSN-TKIP                                */
 502         /*  Values (0x)   :   00                03    07        29                      49                      31                      51                                      */
 503         /*                                                                                                                                                                                                              */
 504         /*  Configuration : WPA-AES+TKIP RSN-AES+TKIP                                                                                                                   */
 505         /*  Values (0x)   :      69                             71                                                                                                                              */
 506         /*  ------------------------------------------------------------------   */
 507         WID_11I_MODE                       = 0x000C,
 508
 509         /*  WEP Configuration: Used in BSS STA mode only when WEP is enabled     */
 510         /*  ------------------------------------------------------------------   */
 511         /*  Configuration : Open System  Shared Key  Any Type  |   802.1x Auth   */
 512         /*  Values (0x)   :    01             02         03    |      BIT2       */
 513         /*  ------------------------------------------------------------------   */
 514         WID_AUTH_TYPE                      = 0x000D,
 515
 516         /*  Site Survey Type                                                                                                                                                                    */
 517         /*  --------------------------------------------------------------      */
 518         /*  Configuration       :  Values to set                                                                                                                                */
 519         /*  Survey 1 Channel    :  0                                                                                                                                                    */
 520         /*  survey all Channels :  1                                                                                                                                                    */
 521         /*  Disable Site Survey :  2                                                                                                                                                    */
 522         /*  --------------------------------------------------------------      */
 523         WID_SITE_SURVEY                    = 0x000E,
 524
 525         /*  Listen Interval                                                      */
 526         /*  --------------------------------------------------------------       */
 527         /*  Configuration :   Any value between 1 to 255                         */
 528         /*  Values to set :   Same value. Default is 3                           */
 529         /*  --------------------------------------------------------------       */
 530         WID_LISTEN_INTERVAL                = 0x000F,
 531
 532         /*  DTIM Period                                                          */
 533         /*  --------------------------------------------------------------       */
 534         /*  Configuration :   Any value between 1 to 255                         */
 535         /*  Values to set :   Same value. Default is 3                           */
 536         /*  --------------------------------------------------------------       */
 537         WID_DTIM_PERIOD                    = 0x0010,
 538
 539         /*  ACK Policy                                                           */
 540         /*  --------------------------------------------------------------       */
 541         /*  Configuration :   Normal Ack            No Ack                       */
 542         /*  Values to set :       0                   1                          */
 543         /*  --------------------------------------------------------------       */
 544         WID_ACK_POLICY                     = 0x0011,
 545
 546         /*  Reset MAC (Set only)                                                           */
 547         /*  --------------------------------------------------------------       */
 548         /*  Configuration :   Don't Reset       Reset   No Request                       */
 549         /*  Values to set :       0                   1                 2                          */
 550         /*  --------------------------------------------------------------       */
 551         WID_RESET                          = 0x0012,
 552
 553         /*  Broadcast SSID Option: Setting this will adhere to "" SSID element   */
 554         /*  ------------------------------------------------------------------   */
 555         /*  Configuration :   Enable             Disable                         */
 556         /*  Values to set :   1                  0                               */
 557         /*  ------------------------------------------------------------------   */
 558         WID_BCAST_SSID                     = 0x0015,
 559
 560         /*  Disconnect (Station)                                                                                                                                                                                                                */
 561         /*  ------------------------------------------------------------------  */
 562         /*  Configuration :   Association ID                                                                                                                                                    */
 563         /*  Values to set :   Association ID                                                                                                                                                    */
 564         /*  ------------------------------------------------------------------  */
 565         WID_DISCONNECT                     = 0x0016,
 566
 567         /*  11a Tx Power Level                                                   */
 568         /*  -------------------------------------------------------------------- */
 569         /*  Configuration : Sets TX Power (Higher the value greater the power)   */
 570         /*  Values to set : Any value between 0 and 63 (inclusive; Default is 48)*/
 571         /*  -------------------------------------------------------------------- */
 572         WID_TX_POWER_LEVEL_11A             = 0x0018,
 573
 574         /*  Group Key Update Policy Selection                                    */
 575         /*  -------------------------------------------------------------------- */
 576         /*  Configuration : Disabled  timeBased  packetBased   timePacketBased   */
 577         /*  Values to set :   1            2          3               4          */
 578         /*  -------------------------------------------------------------------- */
 579         WID_REKEY_POLICY                   = 0x0019,
 580
 581         /*  Allow Short Slot                                                     */
 582         /*  --------------------------------------------------------------       */
 583         /*  Configuration : Disallow Short Slot      Allow Short Slot            */
 584         /*              (Enable Only Long Slot) (Enable Short Slot if applicable)*/
 585         /*  Values to set :    0         1                                       */
 586         /*  --------------------------------------------------------------       */
 587         WID_SHORT_SLOT_ALLOWED             = 0x001A,
 588
 589         WID_PHY_ACTIVE_REG                 = 0x001B,
 590
 591         /*  11b Tx Power Level                                                   */
 592         /*  -------------------------------------------------------------------- */
 593         /*  Configuration : Sets TX Power (Higher the value greater the power)   */
 594         /*  Values to set : Any value between 0 and 63 (inclusive; Default is 48)*/
 595         /*  -------------------------------------------------------------------- */
 596         WID_TX_POWER_LEVEL_11B             = 0x001D,
 597
 598         /*  Scan Request                                                                                                                                                                                        */
 599         /*  --------------------------------------------------------------------        */
 600         /*  Configuration : Request default scan                                                                                                                                                                        */
 601         /*  Values to set : 0                                                                                                                                                                                                                                   */
 602         /*  -------------------------------------------------------------------- */
 603         WID_START_SCAN_REQ                 = 0x001E,
 604
 605         /*  Rssi (get only)                                                                                                                                                                                     */
 606         /*  --------------------------------------------------------------------        */
 607         /*  Configuration :                                                                                                                                                                     */
 608         /*  Values to get : Rssi value                                                                                                                                                                                                                                  */
 609         /*  -------------------------------------------------------------------- */
 610         WID_RSSI                           = 0x001F,
 611
 612         /*  Join Request                                                                                                                                                                                        */
 613         /*  --------------------------------------------------------------------        */
 614         /*  Configuration : Request to join                                                                                                                                                                     */
 615         /*  Values to set : index of scan result                                                                                                                                                                        */
 616         /*  -------------------------------------------------------------------- */
 617         WID_JOIN_REQ                       = 0x0020,
 618
 619         WID_LINKSPEED                                                           = 0x0026,
 620
 621         /*  Enable User Control of TX Power                                      */
 622         /*  -------------------------------------------------------------------- */
 623         /*  Configuration : Disable                  Enable                      */
 624         /*  Values to set :    0                       1                         */
 625         /*  -------------------------------------------------------------------- */
 626         WID_USER_CONTROL_ON_TX_POWER       = 0x0027,
 627
 628         WID_MEMORY_ACCESS_8BIT             = 0x0029,
 629
 630         /*  Enable Auto RX Sensitivity feature                                                                                                                                                          */
 631         /*  --------------------------------------------------------------------        */
 632         /*  Configuration : Disable                  Enable                                                                                                                                     */
 633         /*  Values to set :    0                       1                                                                                                                                                        */
 634         /*  --------------------------------------------------------------------        */
 635         WID_AUTO_RX_SENSITIVITY            = 0x0032,
 636
 637         /*  Receive Buffer Based Ack                                                                                                                                                                            */
 638         /*  --------------------------------------------------------------------        */
 639         /*  Configuration : Disable                  Enable                                                                                                                                     */
 640         /*  Values to set :    0                       1                                                                                                                                                        */
 641         /*  --------------------------------------------------------------------        */
 642         WID_DATAFLOW_CONTROL               = 0x0033,
 643
 644         /*  Scan Filter                                                                                                                                                                                 */
 645         /*  --------------------------------------------------------------------        */
 646         /*  Configuration : Class               No filter       AP only                 Station Only                                                                            */
 647         /*  Values to set :                                     0                     1                     2                                                                                           */
 648         /*  Configuration : Priority    High Rssi       Low Rssi                Detect                                                                                                  */
 649         /*  Values to set :                                     0                  0x4                  0x08                                                                                    */
 650         /*  Configuration : Channel     filter off              filter on                                                                                                                                       */
 651         /*  Values to set :                                     0                  0x10                                                                                                                 */
 652         /*  --------------------------------------------------------------------        */
 653         WID_SCAN_FILTER                    = 0x0036,
 654
 655         /*  Link Loss Threshold (measure in the beacon period)                                                                          */
 656         /*  --------------------------------------------------------------------        */
 657         /*  Configuration : Any value between 10 and 254 (Set to 255 to disable it)                                                             */
 658         /*  Values to set : Same value. Default is 10                                                                                                                                                           */
 659         /*  --------------------------------------------------------------------        */
 660         WID_LINK_LOSS_THRESHOLD            = 0x0037,
 661
 662         /*BugID_4978*/
 663         WID_ABORT_RUNNING_SCAN = 0x003E,
 664
 665         /* NMAC Character WID list */
 666         WID_WPS_START                      = 0x0043,
 667
 668         /*  Protection mode for MAC                                              */
 669         /*  --------------------------------------------------------------       */
 670         /*  Configuration :  Auto  No protection  ERP    HT    GF                */
 671         /*  Values to set :  0     1              2      3     4                 */
 672         /*  --------------------------------------------------------------       */
 673         WID_11N_PROT_MECH                  = 0x0080,
 674
 675         /*  ERP Protection type for MAC                                          */
 676         /*  --------------------------------------------------------------       */
 677         /*  Configuration :  Self-CTS   RTS-CTS                                  */
 678         /*  Values to set :  0          1                                        */
 679         /*  --------------------------------------------------------------       */
 680         WID_11N_ERP_PROT_TYPE              = 0x0081,
 681
 682         /*  HT Option Enable                                                     */
 683         /*  --------------------------------------------------------------       */
 684         /*  Configuration :   HT Enable          HT Disable                       */
 685         /*  Values to set :   1                  0                               */
 686         /*  --------------------------------------------------------------       */
 687         WID_11N_ENABLE                     = 0x0082,
 688
 689         /*  11n Operating mode (Note that 11g operating mode will also be        */
 690         /*  used in addition to this, if this is set to HT Mixed mode)           */
 691         /*  --------------------------------------------------------------       */
 692         /*  Configuration :  HT Mixed  HT Only-20MHz   HT Only-20/40MHz          */
 693         /*  Values to set :     1         2               3                         */
 694         /*  --------------------------------------------------------------       */
 695         WID_11N_OPERATING_MODE             = 0x0083,
 696
 697         /*  11n OBSS non-HT STA Detection flag                                   */
 698         /*  --------------------------------------------------------------       */
 699         /*  Configuration :  Do not detect                                       */
 700         /*  Values to set :  0                                                   */
 701         /*  Configuration :  Detect, do not protect or report                    */
 702         /*  Values to set :  1                                                   */
 703         /*  Configuration :  Detect, protect and do not report                   */
 704         /*  Values to set :  2                                                   */
 705         /*  Configuration :  Detect, protect and report to other BSS             */
 706         /*  Values to set :  3                                                   */
 707         /*  --------------------------------------------------------------       */
 708         WID_11N_OBSS_NONHT_DETECTION       = 0x0084,
 709
 710         /*  11n HT Protection Type                                               */
 711         /*  --------------------------------------------------------------       */
 712         /*  Configuration :  RTS-CTS   First Frame Exchange at non-HT-rate       */
 713         /*  Values to set :  0         1                                         */
 714         /*  Configuration :  LSIG TXOP First Frame Exchange in Mixed Fmt         */
 715         /*  Values to set :  2         3                                         */
 716         /*  --------------------------------------------------------------       */
 717         WID_11N_HT_PROT_TYPE               = 0x0085,
 718
 719         /*  11n RIFS Protection Enable Flag                                      */
 720         /*  --------------------------------------------------------------       */
 721         /*  Configuration :  Disable    Enable                                   */
 722         /*  Values to set :  0          1                                        */
 723         /*  --------------------------------------------------------------       */
 724         WID_11N_RIFS_PROT_ENABLE           = 0x0086,
 725
 726         /*  SMPS Mode                                                            */
 727         /*  --------------------------------------------------------------       */
 728         /*  Configuration :  Static   Dynamic   MIMO (Power Save Disabled)       */
 729         /*  Values to set :  1        2         3                                */
 730         /*  --------------------------------------------------------------       */
 731         WID_11N_SMPS_MODE                  = 0x0087,
 732
 733         /*  Current transmit MCS                                                 */
 734         /*  --------------------------------------------------------------       */
 735         /*  Configuration :  MCS Index for data rate                                                                                                                    */
 736         /*  Values to set :  0 to 7                                                                                                                                                     */
 737         /*  --------------------------------------------------------------       */
 738         WID_11N_CURRENT_TX_MCS             = 0x0088,
 739
 740         WID_11N_PRINT_STATS                = 0x0089,
 741
 742         /*  11n Short GI Enable Flag                                                                                                                                                    */
 743         /*  --------------------------------------------------------------       */
 744         /*  Configuration :  Disable    Enable                                                                                                                                  */
 745         /*  Values to set :  0          1                                                                                                                                                       */
 746         /*  --------------------------------------------------------------       */
 747         WID_11N_SHORT_GI_ENABLE            = 0x008D,
 748
 749         /*  11n RIFS Enable Flag                                                                                                                                                */
 750         /*  --------------------------------------------------------------       */
 751         /*  Configuration :  Disable    Enable                                                                                                                                  */
 752         /*  Values to set :  0          1                                                                                                                                                       */
 753         /*  --------------------------------------------------------------       */
 754         WID_RIFS_MODE                      = 0x0094,
 755
 756         /*  TX Abort Feature                                                                                                                                                    */
 757         /*  --------------------------------------------------------------       */
 758         /*  Configuration :  Disable Self CTS    Enable Self CTS                                                                                                        */
 759         /*  Values to set :             0                                       1                                                                                                                               */
 760         /*  Configuration :  Disable TX Abort    Enable TX Abort                                                                                                        */
 761         /*  Values to set :             2                                       3                                                                                                                               */
 762         /*  Configuration :  Enable HW TX Abort Enable SW TX Abort                                                                                              */
 763         /*  Values to set :             4                                       5                                                                                                                               */
 764         /*  --------------------------------------------------------------       */
 765         WID_TX_ABORT_CONFIG                = 0x00A1,
 766
 767         WID_REG_TSSI_11B_VALUE             = 0x00A6,
 768         WID_REG_TSSI_11G_VALUE             = 0x00A7,
 769         WID_REG_TSSI_11N_VALUE             = 0x00A8,
 770         WID_TX_CALIBRATION                 = 0x00A9,
 771         WID_DSCR_TSSI_11B_VALUE            = 0x00AA,
 772         WID_DSCR_TSSI_11G_VALUE            = 0x00AB,
 773         WID_DSCR_TSSI_11N_VALUE            = 0x00AC,
 774
 775         /*  Immediate Block-Ack Support                                          */
 776         /*  --------------------------------------------------------------       */
 777         /*  Configuration : Disable                  Enable                      */
 778         /*  Values to set :    0                       1                         */
 779         /*  --------------------------------------------------------------       */
 780         WID_11N_IMMEDIATE_BA_ENABLED       = 0x00AF,
 781
 782         /*  TXOP Disable Flag                                                                                                                                                                   */
 783         /*  --------------------------------------------------------------      */
 784         /*  Configuration : Disable                  Enable                                                                                                                     */
 785         /*  Values to set :    1                        0                                                                                                                               */
 786         /*  --------------------------------------------------------------      */
 787         WID_11N_TXOP_PROT_DISABLE          = 0x00B0,
 788
 789
 790         WID_TX_POWER_LEVEL_11N             = 0x00B1,
 791
 792         /* Custom Character WID list */
 793         WID_PC_TEST_MODE          = 0x00C8,
 794         /*bug3819: */
 795         /* SCAN Complete notification WID*/
 796         WID_SCAN_COMPLETE               = 0x00C9,
 797
 798 #ifdef WILC_AP_EXTERNAL_MLME
 799         WID_DEL_BEACON                                  = 0x00CA,
 800 #endif
 801
 802         WID_LOGTerminal_Switch                                  = 0x00CD,
 803         /* EMAC Short WID list */
 804         /*  RTS Threshold                                                        */
 805         /*  --------------------------------------------------------------       */
 806         /*  Configuration :   Any value between 256 to 2347                      */
 807         /*  Values to set :   Same value. Default is 2347                        */
 808         /*  --------------------------------------------------------------       */
 809         WID_RTS_THRESHOLD                  = 0x1000,
 810
 811         /*  Fragmentation Threshold                                              */
 812         /*  --------------------------------------------------------------       */
 813         /*  Configuration :   Any value between 256 to 2346                      */
 814         /*  Values to set :   Same value. Default is 2346                        */
 815         /*  --------------------------------------------------------------       */
 816         WID_FRAG_THRESHOLD                 = 0x1001,
 817
 818         WID_SHORT_RETRY_LIMIT              = 0x1002,
 819         WID_LONG_RETRY_LIMIT               = 0x1003,
 820         WID_BEACON_INTERVAL                = 0x1006,
 821         WID_MEMORY_ACCESS_16BIT            = 0x1008,
 822         WID_RX_SENSE                       = 0x100B,
 823         WID_ACTIVE_SCAN_TIME               = 0x100C,
 824         WID_PASSIVE_SCAN_TIME              = 0x100D,
 825
 826         WID_SITE_SURVEY_SCAN_TIME          = 0x100E,
 827         WID_JOIN_START_TIMEOUT             = 0x100F,
 828         WID_AUTH_TIMEOUT                   = 0x1010,
 829         WID_ASOC_TIMEOUT                   = 0x1011,
 830         WID_11I_PROTOCOL_TIMEOUT           = 0x1012,
 831         WID_EAPOL_RESPONSE_TIMEOUT         = 0x1013,
 832
 833         /* NMAC Short WID list */
 834         WID_11N_SIG_QUAL_VAL               = 0x1085,
 835         WID_CCA_THRESHOLD                  = 0x1087,
 836
 837         /* Custom Short WID list */
 838
 839         /* EMAC Integer WID list */
 840         WID_FAILED_COUNT                   = 0x2000,
 841         WID_RETRY_COUNT                    = 0x2001,
 842         WID_MULTIPLE_RETRY_COUNT           = 0x2002,
 843         WID_FRAME_DUPLICATE_COUNT          = 0x2003,
 844         WID_ACK_FAILURE_COUNT              = 0x2004,
 845         WID_RECEIVED_FRAGMENT_COUNT        = 0x2005,
 846         WID_MCAST_RECEIVED_FRAME_COUNT     = 0x2006,
 847         WID_FCS_ERROR_COUNT                = 0x2007,
 848         WID_SUCCESS_FRAME_COUNT            = 0x2008,
 849         WID_HUT_TX_COUNT                   = 0x200A,
 850         WID_TX_FRAGMENT_COUNT              = 0x200B,
 851         WID_TX_MULTICAST_FRAME_COUNT       = 0x200C,
 852         WID_RTS_SUCCESS_COUNT              = 0x200D,
 853         WID_RTS_FAILURE_COUNT              = 0x200E,
 854         WID_WEP_UNDECRYPTABLE_COUNT        = 0x200F,
 855         WID_REKEY_PERIOD                   = 0x2010,
 856         WID_REKEY_PACKET_COUNT             = 0x2011,
 857         WID_1X_SERV_ADDR                   = 0x2012,
 858         WID_STACK_IP_ADDR                  = 0x2013,
 859         WID_STACK_NETMASK_ADDR             = 0x2014,
 860         WID_HW_RX_COUNT                    = 0x2015,
 861         WID_MEMORY_ADDRESS                 = 0x201E,
 862         WID_MEMORY_ACCESS_32BIT            = 0x201F,
 863         WID_RF_REG_VAL                     = 0x2021,
 864
 865
 866         /* NMAC Integer WID list */
 867         WID_11N_PHY_ACTIVE_REG_VAL         = 0x2080,
 868
 869         /* Custom Integer WID list */
 870         WID_GET_INACTIVE_TIME     = 0x2084,
 871         WID_SET_DRV_HANDLER =            0X2085,
 872         WID_SET_OPERATION_MODE =         0X2086,
 873         /* EMAC String WID list */
 874         WID_SSID                           = 0x3000,
 875         WID_FIRMWARE_VERSION               = 0x3001,
 876         WID_OPERATIONAL_RATE_SET           = 0x3002,
 877         WID_BSSID                          = 0x3003,
 878         WID_WEP_KEY_VALUE                  = 0x3004,
 879         WID_11I_PSK                        = 0x3008,
 880         WID_11E_P_ACTION_REQ               = 0x3009,
 881         WID_1X_KEY                         = 0x300A,
 882         WID_HARDWARE_VERSION               = 0x300B,
 883         WID_MAC_ADDR                       = 0x300C,
 884         WID_HUT_DEST_ADDR                  = 0x300D,
 885         WID_PHY_VERSION                    = 0x300F,
 886         WID_SUPP_USERNAME                  = 0x3010,
 887         WID_SUPP_PASSWORD                  = 0x3011,
 888         WID_SITE_SURVEY_RESULTS            = 0x3012,
 889         WID_RX_POWER_LEVEL                 = 0x3013,
 890         WID_DEL_ALL_RX_BA                               = 0x3014,
 891         WID_SET_STA_MAC_INACTIVE_TIME   = 0x3017,
 892         WID_ADD_WEP_KEY                    = 0x3019,
 893         WID_REMOVE_WEP_KEY                 = 0x301A,
 894         WID_ADD_PTK                        = 0x301B,
 895         WID_ADD_RX_GTK                     = 0x301C,
 896         WID_ADD_TX_GTK                     = 0x301D,
 897         WID_REMOVE_KEY                     = 0x301E,
 898         WID_ASSOC_REQ_INFO                 = 0x301F,
 899         WID_ASSOC_RES_INFO                 = 0x3020,
 900         WID_MANUFACTURER                   = 0x3026, /*Added for CAPI tool */
 901         WID_MODEL_NAME                                     = 0x3027, /*Added for CAPI tool */
 902         WID_MODEL_NUM                      = 0x3028, /*Added for CAPI tool */
 903         WID_DEVICE_NAME                                     = 0x3029, /*Added for CAPI tool */
 904
 905         /* NMAC String WID list */
 906         WID_11N_P_ACTION_REQ               = 0x3080,
 907         WID_HUT_TEST_ID                    = 0x3081,
 908         WID_PMKID_INFO                     = 0x3082,
 909         WID_FIRMWARE_INFO                  = 0x3083,
 910         #ifdef WILC_P2P
 911         WID_REGISTER_FRAME                = 0x3084,
 912         #endif
 913         WID_DEL_ALL_STA          = 0x3085,
 914          #ifdef WILC_P2P
 915         WID_REMAIN_ON_CHAN  = 0x3996,
 916         #endif
 917         /*BugID_4156*/
 918         WID_SSID_PROBE_REQ = 0x3997,
 919         /*BugID_4124 WID to trigger modified Join Request using SSID and BSSID instead of bssListIdx (used by WID_JOIN_REQ)*/
 920         WID_JOIN_REQ_EXTENDED            = 0x3998,
 921
 922         /* BugID 4951: WID toset IP address in firmware */
 923         WID_IP_ADDRESS                                  = 0x3999,
 924
 925
 926
 927         /* Custom String WID list */
 928
 929         /* EMAC Binary WID list */
 930         WID_UAPSD_CONFIG                   = 0x4001,
 931         WID_UAPSD_STATUS                   = 0x4002,
 932         WID_WMM_AP_AC_PARAMS               = 0x4003,
 933         WID_WMM_STA_AC_PARAMS              = 0x4004,
 934         WID_NETWORK_INFO                   = 0x4005,
 935         WID_STA_JOIN_INFO                  = 0x4006,
 936         WID_CONNECTED_STA_LIST             = 0x4007,
 937
 938         /* NMAC Binary WID list */
 939         WID_11N_AUTORATE_TABLE             = 0x4080,
 940
 941
 942         /*Added here by Amr - BugID 4134*/
 943         WID_SCAN_CHANNEL_LIST                      = 0x4084,
 944
 945         /*BugID_3746 WID to add IE to be added in next probe request*/
 946         WID_INFO_ELEMENT_PROBE   = 0x4085,
 947         /*BugID_3746 WID to add IE to be added in next associate request*/
 948         WID_INFO_ELEMENT_ASSOCIATE       = 0x4086,
 949         WID_ADD_STA                                      = 0X4087,
 950         WID_REMOVE_STA                           = 0X4088,
 951         WID_EDIT_STA                                     = 0X4089,
 952         WID_ADD_BEACON                          = 0x408a,
 953
 954         /* BugID 5108 */
 955         WID_SETUP_MULTICAST_FILTER      = 0x408b,
 956
 957         /* Miscellaneous WIDs */
 958         WID_ALL                            = 0x7FFE,
 959         WID_MAX                            = 0xFFFF
 960 } WID_T;
 961
 962 int wilc_wlan_init(wilc_wlan_inp_t *inp, wilc_wlan_oup_t *oup);
 963
 964 void wilc_bus_set_max_speed(void);
 965 void wilc_bus_set_default_speed(void);
 966 uint32_t wilc_get_chipid(uint8_t update);
 967
 968
 969 #endif