drivers/staging/wilc1000/wilc_wlan_if.h

   1 /* ///////////////////////////////////////////////////////////////////////// */
   2 /*  */
   3 /* Copyright (c) Atmel Corporation.  All rights reserved. */
   4 /*  */
   5 /* Module Name:  wilc_wlan_if.h */
   6 /*  */
   7 /*  */
   8 /* ///////////////////////////////////////////////////////////////////////// */
   9
  10 #ifndef WILC_WLAN_IF_H
  11 #define WILC_WLAN_IF_H
  12
  13 /* #define MEMORY_STATIC */
  14 /* #define USE_OLD_SPI_SW */
  15
  16 #include <linux/semaphore.h>
  17 #include "linux_wlan_common.h"
  18
  19 /********************************************
  20  *
  21  *      Debug Flags
  22  *
  23  ********************************************/
  24
  25 #define N_INIT                  0x00000001
  26 #define N_ERR                   0x00000002
  27 #define N_TXQ                   0x00000004
  28 #define N_INTR                  0x00000008
  29 #define N_RXQ                   0x00000010
  30
  31 /********************************************
  32  *
  33  *      Host Interface Defines
  34  *
  35  ********************************************/
  36
  37 #define HIF_SDIO                (0)
  38 #define HIF_SPI                 BIT(0)
  39 #define HIF_SDIO_GPIO_IRQ       BIT(2)
  40
  41 /********************************************
  42  *
  43  *      Tx/Rx Buffer Size Defines
  44  *
  45  ********************************************/
  46
  47 #define CE_TX_BUFFER_SIZE       (64 * 1024)
  48 #define CE_RX_BUFFER_SIZE       (384 * 1024)
  49
  50 /********************************************
  51  *
  52  *      Wlan Interface Defines
  53  *
  54  ********************************************/
  55
  56 typedef struct {
  57         u32 read_write:         1;
  58         u32 function:           3;
  59         u32 raw:                1;
  60         u32 address:            17;
  61         u32 data:               8;
  62 } sdio_cmd52_t;
  63
  64 typedef struct {
  65         /* struct { */
  66         u32 read_write:         1;
  67         u32 function:           3;
  68         u32 block_mode:         1;
  69         u32 increment:          1;
  70         u32 address:            17;
  71         u32 count:              9;
  72         /* } bit; */
  73         u8 *buffer;
  74         u32 block_size;
  75 } sdio_cmd53_t;
  76
  77 typedef struct {
  78         int io_type;
  79         int (*io_init)(void *);
  80         void (*io_deinit)(void *);
  81         union {
  82                 struct {
  83                         int (*sdio_cmd52)(sdio_cmd52_t *);
  84                         int (*sdio_cmd53)(sdio_cmd53_t *);
  85                         int (*sdio_set_max_speed)(void);
  86                         int (*sdio_set_default_speed)(void);
  87                 } sdio;
  88                 struct {
  89                         int (*spi_max_speed)(void);
  90                         int (*spi_tx)(u8 *, u32);
  91                         int (*spi_rx)(u8 *, u32);
  92                         int (*spi_trx)(u8 *, u8 *, u32);
  93                 } spi;
  94         } u;
  95 } wilc_wlan_io_func_t;
  96
  97 #define WILC_MAC_INDICATE_STATUS        0x1
  98 #define WILC_MAC_STATUS_INIT            -1
  99 #define WILC_MAC_STATUS_READY           0
 100 #define WILC_MAC_STATUS_CONNECT         1
 101
 102 #define WILC_MAC_INDICATE_SCAN          0x2
 103
 104 typedef struct {
 105         void *os_private;
 106 } wilc_wlan_os_context_t;
 107
 108 typedef struct {
 109         wilc_wlan_os_context_t os_context;
 110         wilc_wlan_io_func_t io_func;
 111 } wilc_wlan_inp_t;
 112
 113 struct tx_complete_data {
 114         int size;
 115         void *buff;
 116         u8 *pBssid;
 117         struct sk_buff *skb;
 118 };
 119
 120 typedef void (*wilc_tx_complete_func_t)(void *, int);
 121
 122 #define WILC_TX_ERR_NO_BUF      (-2)
 123
 124 typedef struct {
 125         void (*wlan_handle_rx_isr)(void);
 126         void (*wlan_cleanup)(void);
 127         int (*wlan_cfg_set)(int, u32, u8 *, u32, int, u32);
 128         int (*wlan_cfg_get)(int, u32, int, u32);
 129         int (*wlan_cfg_get_value)(u32, u8 *, u32);
 130         int (*wlan_add_mgmt_to_tx_que)(void *, u8 *, u32,
 131                                        wilc_tx_complete_func_t);
 132 } wilc_wlan_oup_t;
 133
 134 /********************************************
 135  *
 136  *      Wlan Configuration ID
 137  *
 138  ********************************************/
 139
 140 #define MAX_SSID_LEN            33
 141 #define MAX_RATES_SUPPORTED     12
 142
 143 #define INFINITE_SLEEP_TIME     ((u32)0xFFFFFFFF)
 144
 145 typedef enum {
 146         SUPP_RATES_IE           = 1,
 147         EXT_SUPP_RATES_IE       = 50,
 148         HT_CAPABILITY_IE        = 45,
 149         RSN_IE                  = 48,
 150         WPA_IE                  = 221,
 151         WMM_IE                  = 221,
 152         P2P_IE                  = 221,
 153 } BEACON_IE;
 154
 155 typedef enum {
 156         INFRASTRUCTURE          = 0,
 157         INDEPENDENT,
 158         AP,
 159 } BSSTYPE_T;
 160
 161 typedef enum {
 162         RATE_AUTO               = 0,
 163         RATE_1MB                = 1,
 164         RATE_2MB                = 2,
 165         RATE_5MB                = 5,
 166         RATE_6MB                = 6,
 167         RATE_9MB                = 9,
 168         RATE_11MB               = 11,
 169         RATE_12MB               = 12,
 170         RATE_18MB               = 18,
 171         RATE_24MB               = 24,
 172         RATE_26MB               = 36,
 173         RATE_48MB               = 48,
 174         RATE_54MB               = 54
 175 } TX_RATE_T;
 176
 177 typedef enum {
 178         B_ONLY_MODE             = 0,    /* 1, 2 M, otherwise 5, 11 M */
 179         G_ONLY_MODE,                    /* 6,12,24 otherwise 9,18,36,48,54 */
 180         G_MIXED_11B_1_MODE,             /* 1,2,5.5,11 otherwise all on */
 181         G_MIXED_11B_2_MODE,             /* 1,2,5,11,6,12,24 otherwise all on */
 182 } G_OPERATING_MODE_T;
 183
 184 typedef enum {
 185         G_SHORT_PREAMBLE        = 0,    /* Short Preamble */
 186         G_LONG_PREAMBLE         = 1,    /* Long Preamble */
 187         G_AUTO_PREAMBLE         = 2,    /* Auto Preamble Selection */
 188 } G_PREAMBLE_T;
 189
 190 #define MAC_CONNECTED           1
 191 #define MAC_DISCONNECTED        0
 192
 193 #define SCAN_DONE               TRUE
 194 typedef enum {
 195         PASSIVE_SCAN            = 0,
 196         ACTIVE_SCAN             = 1,
 197 } SCANTYPE_T;
 198
 199 typedef enum {
 200         NO_POWERSAVE            = 0,
 201         MIN_FAST_PS             = 1,
 202         MAX_FAST_PS             = 2,
 203         MIN_PSPOLL_PS           = 3,
 204         MAX_PSPOLL_PS           = 4
 205 } USER_PS_MODE_T;
 206
 207 typedef enum {
 208         CHIP_WAKEDUP            = 0,
 209         CHIP_SLEEPING_AUTO      = 1,
 210         CHIP_SLEEPING_MANUAL    = 2
 211 } CHIP_PS_STATE_T;
 212
 213 typedef enum {
 214         ACQUIRE_ONLY            = 0,
 215         ACQUIRE_AND_WAKEUP      = 1,
 216 } BUS_ACQUIRE_T;
 217
 218 typedef enum {
 219         RELEASE_ONLY            = 0,
 220         RELEASE_ALLOW_SLEEP     = 1,
 221 } BUS_RELEASE_T;
 222
 223 typedef enum {
 224         NO_SECURITY             = 0,
 225         WEP_40                  = 0x3,
 226         WEP_104                 = 0x7,
 227         WPA_AES                 = 0x29,
 228         WPA_TKIP                = 0x49,
 229         WPA_AES_TKIP            = 0x69, /* Aes or Tkip */
 230         WPA2_AES                = 0x31,
 231         WPA2_TKIP               = 0x51,
 232         WPA2_AES_TKIP           = 0x71, /* Aes or Tkip */
 233 } SECURITY_T;
 234
 235 typedef enum {
 236         OPEN_SYSTEM             = 1,
 237         SHARED_KEY              = 2,
 238         ANY                     = 3,
 239         IEEE8021                = 5
 240 } AUTHTYPE_T;
 241
 242 typedef enum {
 243         SITE_SURVEY_1CH         = 0,
 244         SITE_SURVEY_ALL_CH      = 1,
 245         SITE_SURVEY_OFF         = 2
 246 } SITE_SURVEY_T;
 247
 248 typedef enum {
 249         NORMAL_ACK              = 0,
 250         NO_ACK,
 251 } ACK_POLICY_T;
 252
 253 typedef enum {
 254         DONT_RESET              = 0,
 255         DO_RESET                = 1,
 256         NO_REQUEST              = 2,
 257 } RESET_REQ_T;
 258
 259 typedef enum {
 260         REKEY_DISABLE           = 1,
 261         REKEY_TIME_BASE,
 262         REKEY_PKT_BASE,
 263         REKEY_TIME_PKT_BASE
 264 } RSNA_REKEY_POLICY_T;
 265
 266 typedef enum {
 267         FILTER_NO               = 0x00,
 268         FILTER_AP_ONLY          = 0x01,
 269         FILTER_STA_ONLY         = 0x02
 270 } SCAN_CLASS_FITLER_T;
 271
 272 typedef enum {
 273         PRI_HIGH_RSSI           = 0x00,
 274         PRI_LOW_RSSI            = 0x04,
 275         PRI_DETECT              = 0x08
 276 } SCAN_PRI_T;
 277
 278 typedef enum {
 279         CH_FILTER_OFF           = 0x00,
 280         CH_FILTER_ON            = 0x10
 281 } CH_FILTER_T;
 282
 283 typedef enum {
 284         AUTO_PROT               = 0,    /* Auto */
 285         NO_PROT,                        /* Do not use any protection */
 286         ERP_PROT,                       /* Protect all ERP frame exchanges */
 287         HT_PROT,                        /* Protect all HT frame exchanges  */
 288         GF_PROT,                        /* Protect all GF frame exchanges  */
 289 } N_PROTECTION_MODE_T;
 290
 291 typedef enum {
 292         G_SELF_CTS_PROT,
 293         G_RTS_CTS_PROT,
 294 } G_PROTECTION_MODE_T;
 295
 296 typedef enum {
 297         HT_MIXED_MODE           = 1,
 298         HT_ONLY_20MHZ_MODE,
 299         HT_ONLY_20_40MHZ_MODE,
 300 } N_OPERATING_MODE_T;
 301
 302 typedef enum {
 303         NO_DETECT               = 0,
 304         DETECT_ONLY             = 1,
 305         DETECT_PROTECT          = 2,
 306         DETECT_PROTECT_REPORT   = 3,
 307 } N_OBSS_DETECTION_T;
 308
 309 typedef enum {
 310         RTS_CTS_NONHT_PROT      = 0,    /* RTS-CTS at non-HT rate */
 311         FIRST_FRAME_NONHT_PROT,         /* First frame at non-HT rate */
 312         LSIG_TXOP_PROT,                 /* LSIG TXOP Protection */
 313         FIRST_FRAME_MIXED_PROT,         /* First frame at Mixed format */
 314 } N_PROTECTION_TYPE_T;
 315
 316 typedef enum {
 317         STATIC_MODE             = 1,
 318         DYNAMIC_MODE            = 2,
 319         MIMO_MODE               = 3,    /* power save disable */
 320 } N_SMPS_MODE_T;
 321
 322 typedef enum {
 323         DISABLE_SELF_CTS,
 324         ENABLE_SELF_CTS,
 325         DISABLE_TX_ABORT,
 326         ENABLE_TX_ABORT,
 327         HW_TRIGGER_ABORT,
 328         SW_TRIGGER_ABORT,
 329 } TX_ABORT_OPTION_T;
 330
 331 typedef enum {
 332         WID_CHAR                = 0,
 333         WID_SHORT               = 1,
 334         WID_INT                 = 2,
 335         WID_STR                 = 3,
 336         WID_BIN_DATA            = 4,
 337         WID_BIN                 = 5,
 338         WID_IP                  = 6,
 339         WID_ADR                 = 7,
 340         WID_UNDEF               = 8,
 341         WID_TYPE_FORCE_32BIT    = 0xFFFFFFFF
 342
 343 } WID_TYPE_T, tenuWIDtype;
 344
 345 typedef enum {
 346         WID_NIL                         = 0xffff,
 347
 348         /*
 349          *  BSS Type
 350          *  -----------------------------------------------------------
 351          *  Configuration : Infrastructure   Independent   Access Point
 352          *  Values to set :         0               1            2
 353          *  -----------------------------------------------------------
 354          */
 355         WID_BSS_TYPE                    = 0x0000,
 356
 357         /*
 358          *  Transmit Rate
 359          *  -----------------------------------------------------------
 360          *  Configuration : 1  2  5.5  11  6  9  12  18  24  36  48  54
 361          *  Values to set : 1  2    5  11  6  9  12  18  24  36  48  54
 362          *  -----------------------------------------------------------
 363          */
 364         WID_CURRENT_TX_RATE             = 0x0001,
 365
 366         /*
 367          *  Channel
 368          *  -----------------------------------------------------------
 369          *  Configuration(g) : 1  2  3  4  5  6  7  8  9 10 11 12 13 14
 370          *  Values to set    : 1  2  3  4  5  6  7  8  9 10 11 12 13 14
 371          *  -----------------------------------------------------------
 372          */
 373         WID_CURRENT_CHANNEL             = 0x0002,
 374
 375         /*
 376          *  Preamble
 377          *  -----------------------------------------------------------
 378          *  Configuration :    short    long      Auto
 379          *  Values to set :       0       1         2
 380          *  -----------------------------------------------------------
 381          */
 382         WID_PREAMBLE                    = 0x0003,
 383
 384         /*
 385          * 11g operating mode (ignored if 11g not present)
 386          *  -----------------------------------------------------------
 387          *  Configuration :   HighPerf  Compat(RSet #1) Compat(RSet #2)
 388          *  Values to set :          1               2               3
 389          *  -----------------------------------------------------------
 390          */
 391         WID_11G_OPERATING_MODE          = 0x0004,
 392
 393         /*
 394          *  Mac status (response only)
 395          *  -----------------------------------------------------------
 396          *  Configuration :   disconnect  connect
 397          *  Values to get :          0       1
 398          *  -----------------------------------------------------------
 399          */
 400         WID_STATUS                      = 0x0005,
 401
 402         /*
 403          *  Scan type
 404          *  -----------------------------------------------------------
 405          *  Configuration :   Passive Scanning   Active Scanning
 406          *  Values to set :                  0                 1
 407          *  -----------------------------------------------------------
 408          */
 409         WID_SCAN_TYPE                   = 0x0007,
 410
 411         /*
 412          *  Key Id (WEP default key Id)
 413          *  -----------------------------------------------------------
 414          *  Configuration :   Any value between 0 to 3
 415          *  Values to set :   Same value. Default is 0
 416          *  -----------------------------------------------------------
 417          */
 418         WID_KEY_ID                      = 0x0009,
 419
 420         /*
 421          *  QoS Enable
 422          *  -----------------------------------------------------------
 423          *  Configuration :   QoS Disable   WMM Enable
 424          *  Values to set :   0             1
 425          *  -----------------------------------------------------------
 426          */
 427         WID_QOS_ENABLE                  = 0x000A,
 428
 429         /*
 430          *  Power Management
 431          *  -----------------------------------------------------------
 432          *  Configuration : NO_POWERSAVE MIN_POWERSAVE MAX_POWERSAVE
 433          *  Values to set : 0            1             2
 434          *  -----------------------------------------------------------
 435          */
 436         WID_POWER_MANAGEMENT            = 0x000B,
 437
 438         /*
 439          *  WEP/802 11I Configuration
 440          *  -----------------------------------------------------------
 441          *  Configuration:Disable WP40 WP104 WPA-AES WPA-TKIP RSN-AES RSN-TKIP
 442          *  Values (0x)  :   00     03   07     29       49       31      51
 443          *  Configuration:WPA-AES+TKIP RSN-AES+TKIP
 444          *  Values (0x)  :      69        71
 445          *  -----------------------------------------------------------
 446          */
 447         WID_11I_MODE                    = 0x000C,
 448
 449         /*
 450          *  WEP Configuration: Used in BSS STA mode only when WEP is enabled
 451          *  -----------------------------------------------------------
 452          *  Configuration : Open System Shared Key Any Type | 802.1x Auth
 453          *  Values (0x)   :    01             02         03 |    BIT2
 454          *  -----------------------------------------------------------
 455          */
 456         WID_AUTH_TYPE                   = 0x000D,
 457
 458         /*
 459          *  Site Survey Type
 460          *  -----------------------------------------------------------
 461          *  Configuration       :  Values to set
 462          *  Survey 1 Channel    :  0
 463          *  survey all Channels :  1
 464          *  Disable Site Survey :  2
 465          *  -----------------------------------------------------------
 466          */
 467         WID_SITE_SURVEY                 = 0x000E,
 468
 469         /*
 470          *  Listen Interval
 471          *  -----------------------------------------------------------
 472          *  Configuration :   Any value between 1 to 255
 473          *  Values to set :   Same value. Default is 3
 474          *  -----------------------------------------------------------
 475          */
 476         WID_LISTEN_INTERVAL             = 0x000F,
 477
 478         /*
 479          *  DTIM Period
 480          *  -----------------------------------------------------------
 481          *  Configuration :   Any value between 1 to 255
 482          *  Values to set :   Same value. Default is 3
 483          *  -----------------------------------------------------------
 484          */
 485         WID_DTIM_PERIOD                 = 0x0010,
 486
 487         /*
 488          *  ACK Policy
 489          *  -----------------------------------------------------------
 490          *  Configuration :   Normal Ack            No Ack
 491          *  Values to set :       0                   1
 492          *  -----------------------------------------------------------
 493          */
 494         WID_ACK_POLICY                  = 0x0011,
 495
 496         /*
 497          *  Reset MAC (Set only)
 498          *  -----------------------------------------------------------
 499          *  Configuration :   Don't Reset       Reset   No Request
 500          *  Values to set :       0               1         2
 501          *  -----------------------------------------------------------
 502          */
 503         WID_RESET                       = 0x0012,
 504
 505         /*
 506          *  Broadcast SSID Option: Setting this will adhere to "" SSID element
 507          *  -----------------------------------------------------------
 508          *  Configuration :   Enable             Disable
 509          *  Values to set :   1                  0
 510          *  -----------------------------------------------------------
 511          */
 512         WID_BCAST_SSID                  = 0x0015,
 513
 514         /*
 515          *  Disconnect (Station)
 516          *  -----------------------------------------------------------
 517          *  Configuration :   Association ID
 518          *  Values to set :   Association ID
 519          *  -----------------------------------------------------------
 520          */
 521         WID_DISCONNECT                  = 0x0016,
 522
 523         /*
 524          *  11a Tx Power Level
 525          *  -----------------------------------------------------------
 526          *  Configuration : Sets TX Power (Higher the value greater the power)
 527          *  Values to set : Any value between 0 and 63 (inclusive Default 48)
 528          *  -----------------------------------------------------------
 529          */
 530         WID_TX_POWER_LEVEL_11A          = 0x0018,
 531
 532         /*
 533          *  Group Key Update Policy Selection
 534          *  -----------------------------------------------------------
 535          *  Configuration : Disabled timeBased packetBased timePacketBased
 536          *  Values to set :   1            2          3              4
 537          *  -----------------------------------------------------------
 538          */
 539         WID_REKEY_POLICY                = 0x0019,
 540
 541         /*
 542          *  Allow Short Slot
 543          *  -----------------------------------------------------------
 544          *  Configuration : Disallow Short Slot      Allow Short Slot
 545          *          (Enable Only Long Slot) (Enable Short Slot if applicable)
 546          *  Values to set :    0         1
 547          *  -----------------------------------------------------------
 548          */
 549         WID_SHORT_SLOT_ALLOWED          = 0x001A,
 550
 551         WID_PHY_ACTIVE_REG              = 0x001B,
 552
 553         /*
 554          *  11b Tx Power Level
 555          *  -----------------------------------------------------------
 556          *  Configuration : Sets TX Power (Higher the value greater the power)
 557          *  Values to set : Any value between 0 and 63 (inclusive Default 48)
 558          *  -----------------------------------------------------------
 559          */
 560         WID_TX_POWER_LEVEL_11B          = 0x001D,
 561
 562         /*
 563          *  Scan Request
 564          *  -----------------------------------------------------------
 565          *  Configuration : Request default scan
 566          *  Values to set : 0
 567          *  -----------------------------------------------------------
 568          */
 569         WID_START_SCAN_REQ              = 0x001E,
 570
 571         /*
 572          *  Rssi (get only)
 573          *  -----------------------------------------------------------
 574          *  Configuration :
 575          *  Values to get : Rssi value
 576          *  -----------------------------------------------------------
 577          */
 578         WID_RSSI                        = 0x001F,
 579
 580         /*
 581          * Join Request
 582          *  -----------------------------------------------------------
 583          *  Configuration : Request to join
 584          *  Values to set : index of scan result
 585          *  -----------------------------------------------------------
 586          */
 587         WID_JOIN_REQ                    = 0x0020,
 588
 589         WID_LINKSPEED                   = 0x0026,
 590
 591         /*
 592          *  Enable User Control of TX Power
 593          *  -----------------------------------------------------------
 594          *  Configuration : Disable                  Enable
 595          *  Values to set :    0                       1
 596          *  -----------------------------------------------------------
 597          */
 598         WID_USER_CONTROL_ON_TX_POWER    = 0x0027,
 599
 600         WID_MEMORY_ACCESS_8BIT          = 0x0029,
 601
 602         /*
 603          *  Enable Auto RX Sensitivity feature
 604          *  -----------------------------------------------------------
 605          *  Configuration : Disable                  Enable
 606          *  Values to set :    0                       1
 607          *  -----------------------------------------------------------
 608          */
 609         WID_AUTO_RX_SENSITIVITY         = 0x0032,
 610
 611         /*
 612          *  Receive Buffer Based Ack
 613          *  -----------------------------------------------------------
 614          *  Configuration : Disable                  Enable
 615          *  Values to set :    0                       1
 616          *  -----------------------------------------------------------
 617          */
 618         WID_DATAFLOW_CONTROL            = 0x0033,
 619
 620         /*
 621          *  Scan Filter
 622          *  -----------------------------------------------------------
 623          *  Configuration : Class       No filter   AP only   Station Only
 624          *  Values to set :                0           1           2
 625          *  Configuration : Priority    High Rssi   Low Rssi     Detect
 626          *  Values to set :                0          0x4         0x0
 627          *  Configuration : Channel     filter off  filter on
 628          *  Values to set :                0          0x10
 629          *  -----------------------------------------------------------
 630          */
 631         WID_SCAN_FILTER                 = 0x0036,
 632
 633         /*
 634          *  Link Loss Threshold (measure in the beacon period)
 635          *  -----------------------------------------------------------
 636          *  Configuration : Any value between 10 and 254(Set to 255 disable)
 637          *  Values to set : Same value. Default is 10
 638          *  -----------------------------------------------------------
 639          */
 640         WID_LINK_LOSS_THRESHOLD         = 0x0037,
 641
 642         WID_ABORT_RUNNING_SCAN          = 0x003E,
 643
 644         /* NMAC Character WID list */
 645         WID_WPS_START                   = 0x0043,
 646
 647         /*
 648          *  Protection mode for MAC
 649          *  -----------------------------------------------------------
 650          *  Configuration :  Auto  No protection  ERP    HT    GF
 651          *  Values to set :  0     1              2      3     4
 652          *  -----------------------------------------------------------
 653          */
 654         WID_11N_PROT_MECH               = 0x0080,
 655
 656         /*
 657          *  ERP Protection type for MAC
 658          *  -----------------------------------------------------------
 659          *  Configuration :  Self-CTS   RTS-CTS
 660          *  Values to set :  0          1
 661          *  -----------------------------------------------------------
 662          */
 663         WID_11N_ERP_PROT_TYPE           = 0x0081,
 664
 665         /*
 666          *  HT Option Enable
 667          *  -----------------------------------------------------------
 668          *  Configuration :   HT Enable          HT Disable
 669          *  Values to set :   1                  0
 670          *  -----------------------------------------------------------
 671          */
 672         WID_11N_ENABLE                  = 0x0082,
 673
 674         /*
 675          *  11n Operating mode (Note that 11g operating mode will also be
 676          *  used in addition to this, if this is set to HT Mixed mode)
 677          *  -----------------------------------------------------------
 678          *   Configuration :  HT Mixed  HT Only-20MHz   HT Only-20/40MHz
 679          *  Values to set :     1         2               3
 680          *  -----------------------------------------------------------
 681          */
 682         WID_11N_OPERATING_MODE          = 0x0083,
 683
 684         /*
 685          *  11n OBSS non-HT STA Detection flag
 686          *  -----------------------------------------------------------
 687          *  Configuration :  Do not detect
 688          *  Values to set :  0
 689          *  Configuration :  Detect, do not protect or report
 690          *  Values to set :  1
 691          *  Configuration :  Detect, protect and do not report
 692          *  Values to set :  2
 693          *  Configuration :  Detect, protect and report to other BSS
 694          *  Values to set :  3
 695          *  -----------------------------------------------------------
 696          */
 697         WID_11N_OBSS_NONHT_DETECTION    = 0x0084,
 698
 699         /*
 700          *  11n HT Protection Type
 701          *  -----------------------------------------------------------
 702          *  Configuration :  RTS-CTS   First Frame Exchange at non-HT-rate
 703          *  Values to set :  0         1
 704          *  Configuration :  LSIG TXOP First Frame Exchange in Mixed Fmt
 705          *  Values to set :  2         3
 706          *  -----------------------------------------------------------
 707          */
 708         WID_11N_HT_PROT_TYPE            = 0x0085,
 709
 710         /*
 711          *  11n RIFS Protection Enable Flag
 712          *  -----------------------------------------------------------
 713          *  Configuration :  Disable    Enable
 714          *  Values to set :  0          1
 715          *  -----------------------------------------------------------
 716          */
 717         WID_11N_RIFS_PROT_ENABLE        = 0x0086,
 718
 719         /*
 720          *  SMPS Mode
 721          *  -----------------------------------------------------------
 722          *  Configuration :  Static   Dynamic   MIMO (Power Save Disabled)
 723          *  Values to set :  1        2         3
 724          *  -----------------------------------------------------------
 725          */
 726         WID_11N_SMPS_MODE               = 0x0087,
 727
 728         /*
 729          *  Current transmit MCS
 730          *  -----------------------------------------------------------
 731          *  Configuration :  MCS Index for data rate
 732          *  Values to set :  0 to 7
 733          *  -----------------------------------------------------------
 734          */
 735         WID_11N_CURRENT_TX_MCS          = 0x0088,
 736
 737         WID_11N_PRINT_STATS             = 0x0089,
 738
 739         /*
 740          *  11n Short GI Enable Flag
 741          *  -----------------------------------------------------------
 742          *  Configuration :  Disable    Enable
 743          *  Values to set :  0          1
 744          *  -----------------------------------------------------------
 745          */
 746         WID_11N_SHORT_GI_ENABLE         = 0x008D,
 747
 748         /*
 749          *  11n RIFS Enable Flag
 750          *  -----------------------------------------------------------
 751          *  Configuration :  Disable    Enable
 752          *  Values to set :  0          1
 753          *  -----------------------------------------------------------
 754          */
 755         WID_RIFS_MODE                   = 0x0094,
 756
 757         /*
 758          *  TX Abort Feature
 759          *  -----------------------------------------------------------
 760          *  Configuration :  Disable Self CTS    Enable Self CTS
 761          *  Values to set :             0                      1
 762          *  Configuration :  Disable TX Abort    Enable TX Abort
 763          *  Values to set :             2                      3
 764          *  Configuration :  Enable HW TX Abort Enable SW TX Abort
 765          *  Values to set :             4                      5
 766          *  -----------------------------------------------------------
 767          */
 768         WID_TX_ABORT_CONFIG             = 0x00A1,
 769
 770         WID_REG_TSSI_11B_VALUE          = 0x00A6,
 771         WID_REG_TSSI_11G_VALUE          = 0x00A7,
 772         WID_REG_TSSI_11N_VALUE          = 0x00A8,
 773         WID_TX_CALIBRATION              = 0x00A9,
 774         WID_DSCR_TSSI_11B_VALUE         = 0x00AA,
 775         WID_DSCR_TSSI_11G_VALUE         = 0x00AB,
 776         WID_DSCR_TSSI_11N_VALUE         = 0x00AC,
 777
 778         /*
 779          *  Immediate Block-Ack Support
 780          *  -----------------------------------------------------------
 781          *  Configuration : Disable                  Enable
 782          *  Values to set :    0                       1
 783          *  -----------------------------------------------------------
 784          */
 785         WID_11N_IMMEDIATE_BA_ENABLED    = 0x00AF,
 786
 787         /*
 788          *  TXOP Disable Flag
 789          *  -----------------------------------------------------------
 790          *  Configuration : Disable                  Enable
 791          *  Values to set :    1                        0
 792          *  -----------------------------------------------------------
 793          */
 794         WID_11N_TXOP_PROT_DISABLE       = 0x00B0,
 795
 796         WID_TX_POWER_LEVEL_11N          = 0x00B1,
 797
 798         /* Custom Character WID list */
 799         WID_PC_TEST_MODE                = 0x00C8,
 800         /* SCAN Complete notification WID*/
 801         WID_SCAN_COMPLETE               = 0x00C9,
 802
 803         WID_DEL_BEACON                  = 0x00CA,
 804
 805         WID_LOGTerminal_Switch          = 0x00CD,
 806         /*  EMAC Short WID list */
 807         /*  RTS Threshold */
 808         /*
 809          *  -----------------------------------------------------------
 810          *  Configuration :   Any value between 256 to 2347
 811          *  Values to set :   Same value. Default is 2347
 812          *  -----------------------------------------------------------
 813          */
 814         WID_RTS_THRESHOLD               = 0x1000,
 815
 816         /*
 817          *  Fragmentation Threshold
 818          *  -----------------------------------------------------------
 819          *  Configuration :   Any value between 256 to 2346
 820          *  Values to set :   Same value. Default is 2346
 821          *  -----------------------------------------------------------
 822          */
 823         WID_FRAG_THRESHOLD              = 0x1001,
 824
 825         WID_SHORT_RETRY_LIMIT           = 0x1002,
 826         WID_LONG_RETRY_LIMIT            = 0x1003,
 827         WID_BEACON_INTERVAL             = 0x1006,
 828         WID_MEMORY_ACCESS_16BIT         = 0x1008,
 829         WID_RX_SENSE                    = 0x100B,
 830         WID_ACTIVE_SCAN_TIME            = 0x100C,
 831         WID_PASSIVE_SCAN_TIME           = 0x100D,
 832
 833         WID_SITE_SURVEY_SCAN_TIME       = 0x100E,
 834         WID_JOIN_START_TIMEOUT          = 0x100F,
 835         WID_AUTH_TIMEOUT                = 0x1010,
 836         WID_ASOC_TIMEOUT                = 0x1011,
 837         WID_11I_PROTOCOL_TIMEOUT        = 0x1012,
 838         WID_EAPOL_RESPONSE_TIMEOUT      = 0x1013,
 839
 840         /* NMAC Short WID list */
 841         WID_11N_SIG_QUAL_VAL            = 0x1085,
 842         WID_CCA_THRESHOLD               = 0x1087,
 843
 844         /* Custom Short WID list */
 845
 846         /* EMAC Integer WID list */
 847         WID_FAILED_COUNT                = 0x2000,
 848         WID_RETRY_COUNT                 = 0x2001,
 849         WID_MULTIPLE_RETRY_COUNT        = 0x2002,
 850         WID_FRAME_DUPLICATE_COUNT       = 0x2003,
 851         WID_ACK_FAILURE_COUNT           = 0x2004,
 852         WID_RECEIVED_FRAGMENT_COUNT     = 0x2005,
 853         WID_MCAST_RECEIVED_FRAME_COUNT  = 0x2006,
 854         WID_FCS_ERROR_COUNT             = 0x2007,
 855         WID_SUCCESS_FRAME_COUNT         = 0x2008,
 856         WID_HUT_TX_COUNT                = 0x200A,
 857         WID_TX_FRAGMENT_COUNT           = 0x200B,
 858         WID_TX_MULTICAST_FRAME_COUNT    = 0x200C,
 859         WID_RTS_SUCCESS_COUNT           = 0x200D,
 860         WID_RTS_FAILURE_COUNT           = 0x200E,
 861         WID_WEP_UNDECRYPTABLE_COUNT     = 0x200F,
 862         WID_REKEY_PERIOD                = 0x2010,
 863         WID_REKEY_PACKET_COUNT          = 0x2011,
 864         WID_1X_SERV_ADDR                = 0x2012,
 865         WID_STACK_IP_ADDR               = 0x2013,
 866         WID_STACK_NETMASK_ADDR          = 0x2014,
 867         WID_HW_RX_COUNT                 = 0x2015,
 868         WID_MEMORY_ADDRESS              = 0x201E,
 869         WID_MEMORY_ACCESS_32BIT         = 0x201F,
 870         WID_RF_REG_VAL                  = 0x2021,
 871
 872         /* NMAC Integer WID list */
 873         WID_11N_PHY_ACTIVE_REG_VAL      = 0x2080,
 874
 875         /* Custom Integer WID list */
 876         WID_GET_INACTIVE_TIME           = 0x2084,
 877         WID_SET_DRV_HANDLER             = 0X2085,
 878         WID_SET_OPERATION_MODE          = 0X2086,
 879         /* EMAC String WID list */
 880         WID_SSID                        = 0x3000,
 881         WID_FIRMWARE_VERSION            = 0x3001,
 882         WID_OPERATIONAL_RATE_SET        = 0x3002,
 883         WID_BSSID                       = 0x3003,
 884         WID_WEP_KEY_VALUE               = 0x3004,
 885         WID_11I_PSK                     = 0x3008,
 886         WID_11E_P_ACTION_REQ            = 0x3009,
 887         WID_1X_KEY                      = 0x300A,
 888         WID_HARDWARE_VERSION            = 0x300B,
 889         WID_MAC_ADDR                    = 0x300C,
 890         WID_HUT_DEST_ADDR               = 0x300D,
 891         WID_PHY_VERSION                 = 0x300F,
 892         WID_SUPP_USERNAME               = 0x3010,
 893         WID_SUPP_PASSWORD               = 0x3011,
 894         WID_SITE_SURVEY_RESULTS         = 0x3012,
 895         WID_RX_POWER_LEVEL              = 0x3013,
 896         WID_DEL_ALL_RX_BA               = 0x3014,
 897         WID_SET_STA_MAC_INACTIVE_TIME   = 0x3017,
 898         WID_ADD_WEP_KEY                 = 0x3019,
 899         WID_REMOVE_WEP_KEY              = 0x301A,
 900         WID_ADD_PTK                     = 0x301B,
 901         WID_ADD_RX_GTK                  = 0x301C,
 902         WID_ADD_TX_GTK                  = 0x301D,
 903         WID_REMOVE_KEY                  = 0x301E,
 904         WID_ASSOC_REQ_INFO              = 0x301F,
 905         WID_ASSOC_RES_INFO              = 0x3020,
 906         WID_MANUFACTURER                = 0x3026, /*Added for CAPI tool */
 907         WID_MODEL_NAME                  = 0x3027, /*Added for CAPI tool */
 908         WID_MODEL_NUM                   = 0x3028, /*Added for CAPI tool */
 909         WID_DEVICE_NAME                 = 0x3029, /*Added for CAPI tool */
 910
 911         /* NMAC String WID list */
 912         WID_11N_P_ACTION_REQ            = 0x3080,
 913         WID_HUT_TEST_ID                 = 0x3081,
 914         WID_PMKID_INFO                  = 0x3082,
 915         WID_FIRMWARE_INFO               = 0x3083,
 916         WID_REGISTER_FRAME              = 0x3084,
 917         WID_DEL_ALL_STA                 = 0x3085,
 918         WID_REMAIN_ON_CHAN              = 0x3996,
 919         WID_SSID_PROBE_REQ              = 0x3997,
 920         WID_JOIN_REQ_EXTENDED           = 0x3998,
 921
 922         WID_IP_ADDRESS                  = 0x3999,
 923
 924         /* Custom String WID list */
 925
 926         /* EMAC Binary WID list */
 927         WID_UAPSD_CONFIG                = 0x4001,
 928         WID_UAPSD_STATUS                = 0x4002,
 929         WID_WMM_AP_AC_PARAMS            = 0x4003,
 930         WID_WMM_STA_AC_PARAMS           = 0x4004,
 931         WID_NETWORK_INFO                = 0x4005,
 932         WID_STA_JOIN_INFO               = 0x4006,
 933         WID_CONNECTED_STA_LIST          = 0x4007,
 934
 935         /* NMAC Binary WID list */
 936         WID_11N_AUTORATE_TABLE          = 0x4080,
 937
 938         WID_SCAN_CHANNEL_LIST           = 0x4084,
 939
 940         WID_INFO_ELEMENT_PROBE          = 0x4085,
 941         WID_INFO_ELEMENT_ASSOCIATE      = 0x4086,
 942         WID_ADD_STA                     = 0X4087,
 943         WID_REMOVE_STA                  = 0X4088,
 944         WID_EDIT_STA                    = 0X4089,
 945         WID_ADD_BEACON                  = 0x408a,
 946
 947         WID_SETUP_MULTICAST_FILTER      = 0x408b,
 948
 949         /* Miscellaneous WIDs */
 950         WID_ALL                         = 0x7FFE,
 951         WID_MAX                         = 0xFFFF
 952 } WID_T;
 953
 954 int wilc_wlan_init(wilc_wlan_inp_t *inp, wilc_wlan_oup_t *oup);
 955
 956 void wilc_bus_set_max_speed(void);
 957 void wilc_bus_set_default_speed(void);
 958 u32 wilc_get_chipid(u8 update);
 959 extern wilc_wlan_oup_t *gpstrWlanOps;
 960
 961 #endif