mmc: sdhci: Enable 8-bit bus width only for 3.0 spec onwards

[karo-tx-uboot.git] / README

diff --git a/README b/README
index a33647623767f52c971e5ca2cc70c653cecf24dc..33bda8c929e1e4e35451b399cf9ca353d6a167a9 100644 (file)
--- a/README
+++ b/README
@@ -201,7 +201,6 @@ Directory Hierarchy:
       /mpc5xx          Files specific to Freescale MPC5xx CPUs
       /mpc5xxx         Files specific to Freescale MPC5xxx CPUs
       /mpc8xx          Files specific to Freescale MPC8xx CPUs
       /mpc5xx          Files specific to Freescale MPC5xx CPUs
       /mpc5xxx         Files specific to Freescale MPC5xxx CPUs
       /mpc8xx          Files specific to Freescale MPC8xx CPUs

-      /mpc8220         Files specific to Freescale MPC8220 CPUs

       /mpc824x         Files specific to Freescale MPC824x CPUs
       /mpc8260         Files specific to Freescale MPC8260 CPUs
       /mpc85xx         Files specific to Freescale MPC85xx CPUs
       /mpc824x         Files specific to Freescale MPC824x CPUs
       /mpc8260         Files specific to Freescale MPC8260 CPUs
       /mpc85xx         Files specific to Freescale MPC85xx CPUs


@@ -485,6 +484,24 @@ The following options need to be configured:
                Thumb2 this flag will result in Thumb2 code generated by
                GCC.
 
                Thumb2 this flag will result in Thumb2 code generated by
                GCC.
 

+               CONFIG_ARM_ERRATA_716044
+               CONFIG_ARM_ERRATA_742230
+               CONFIG_ARM_ERRATA_743622
+               CONFIG_ARM_ERRATA_751472
+
+               If set, the workarounds for these ARM errata are applied early
+               during U-Boot startup. Note that these options force the
+               workarounds to be applied; no CPU-type/version detection
+               exists, unlike the similar options in the Linux kernel. Do not
+               set these options unless they apply!
+
+- CPU timer options:
+               CONFIG_SYS_HZ
+
+               The frequency of the timer returned by get_timer().
+               get_timer() must operate in milliseconds and this CONFIG
+               option must be set to 1000.
+

 - Linux Kernel Interface:
                CONFIG_CLOCKS_IN_MHZ
 
 - Linux Kernel Interface:
                CONFIG_CLOCKS_IN_MHZ
 


@@ -616,14 +633,6 @@ The following options need to be configured:
                boot loader that has already initialized the UART.  Define this
                variable to flush the UART at init time.
 
                boot loader that has already initialized the UART.  Define this
                variable to flush the UART at init time.
 

-               CONFIG_SYS_NS16550_BROKEN_TEMT
-
-               16550 UART set the Transmitter Empty (TEMT) Bit when all output
-               has finished and the transmitter is totally empty. U-Boot waits
-               for this bit to be set to initialize the serial console. On some
-               broken platforms this bit is not set in SPL making U-Boot to
-               hang while waiting for TEMT. Define this option to avoid it.
-

 
 - Console Interface:
                Depending on board, define exactly one serial port
 
 - Console Interface:
                Depending on board, define exactly one serial port


@@ -834,6 +843,7 @@ The following options need to be configured:
                CONFIG_CMD_FDOS         * Dos diskette Support
                CONFIG_CMD_FLASH          flinfo, erase, protect
                CONFIG_CMD_FPGA           FPGA device initialization support
                CONFIG_CMD_FDOS         * Dos diskette Support
                CONFIG_CMD_FLASH          flinfo, erase, protect
                CONFIG_CMD_FPGA           FPGA device initialization support

+               CONFIG_CMD_FUSE           Device fuse support

                CONFIG_CMD_GETTIME      * Get time since boot
                CONFIG_CMD_GO           * the 'go' command (exec code)
                CONFIG_CMD_GREPENV      * search environment
                CONFIG_CMD_GETTIME      * Get time since boot
                CONFIG_CMD_GO           * the 'go' command (exec code)
                CONFIG_CMD_GREPENV      * search environment


@@ -842,7 +852,8 @@ The following options need to be configured:
                CONFIG_CMD_I2C          * I2C serial bus support
                CONFIG_CMD_IDE          * IDE harddisk support
                CONFIG_CMD_IMI            iminfo
                CONFIG_CMD_I2C          * I2C serial bus support
                CONFIG_CMD_IDE          * IDE harddisk support
                CONFIG_CMD_IMI            iminfo

-               CONFIG_CMD_IMLS           List all found images
+               CONFIG_CMD_IMLS           List all images found in NOR flash
+               CONFIG_CMD_IMLS_NAND      List all images found in NAND flash

                CONFIG_CMD_IMMAP        * IMMR dump support
                CONFIG_CMD_IMPORTENV    * import an environment
                CONFIG_CMD_INI          * import data from an ini file into the env
                CONFIG_CMD_IMMAP        * IMMR dump support
                CONFIG_CMD_IMPORTENV    * import an environment
                CONFIG_CMD_INI          * import data from an ini file into the env


@@ -859,7 +870,8 @@ The following options need to be configured:
                                          (requires CONFIG_CMD_MEMORY and CONFIG_MD5)
                CONFIG_CMD_MEMINFO      * Display detailed memory information
                CONFIG_CMD_MEMORY         md, mm, nm, mw, cp, cmp, crc, base,
                                          (requires CONFIG_CMD_MEMORY and CONFIG_MD5)
                CONFIG_CMD_MEMINFO      * Display detailed memory information
                CONFIG_CMD_MEMORY         md, mm, nm, mw, cp, cmp, crc, base,

-                                         loop, loopw, mtest
+                                         loop, loopw
+               CONFIG_CMD_MEMTEST        mtest

                CONFIG_CMD_MISC           Misc functions like sleep etc
                CONFIG_CMD_MMC          * MMC memory mapped support
                CONFIG_CMD_MII          * MII utility commands
                CONFIG_CMD_MISC           Misc functions like sleep etc
                CONFIG_CMD_MMC          * MMC memory mapped support
                CONFIG_CMD_MII          * MII utility commands


@@ -876,6 +888,7 @@ The following options need to be configured:
                CONFIG_CMD_READ         * Read raw data from partition
                CONFIG_CMD_REGINFO      * Register dump
                CONFIG_CMD_RUN            run command in env variable
                CONFIG_CMD_READ         * Read raw data from partition
                CONFIG_CMD_REGINFO      * Register dump
                CONFIG_CMD_RUN            run command in env variable

+               CONFIG_CMD_SANDBOX      * sb command to access sandbox features

                CONFIG_CMD_SAVES        * save S record dump
                CONFIG_CMD_SCSI         * SCSI Support
                CONFIG_CMD_SDRAM        * print SDRAM configuration information
                CONFIG_CMD_SAVES        * save S record dump
                CONFIG_CMD_SCSI         * SCSI Support
                CONFIG_CMD_SDRAM        * print SDRAM configuration information


@@ -885,6 +898,7 @@ The following options need to be configured:
                CONFIG_CMD_SF           * Read/write/erase SPI NOR flash
                CONFIG_CMD_SHA1SUM        print sha1 memory digest
                                          (requires CONFIG_CMD_MEMORY)
                CONFIG_CMD_SF           * Read/write/erase SPI NOR flash
                CONFIG_CMD_SHA1SUM        print sha1 memory digest
                                          (requires CONFIG_CMD_MEMORY)

+               CONFIG_CMD_SOFTSWITCH   * Soft switch setting command for BF60x

                CONFIG_CMD_SOURCE         "source" command Support
                CONFIG_CMD_SPI          * SPI serial bus support
                CONFIG_CMD_TFTPSRV      * TFTP transfer in server mode
                CONFIG_CMD_SOURCE         "source" command Support
                CONFIG_CMD_SPI          * SPI serial bus support
                CONFIG_CMD_TFTPSRV      * TFTP transfer in server mode


@@ -917,6 +931,13 @@ The following options need to be configured:
 
                XXX - this list needs to get updated!
 
 
                XXX - this list needs to get updated!
 

+- Regular expression support:
+               CONFIG_REGEX
+                If this variable is defined, U-Boot is linked against
+                the SLRE (Super Light Regular Expression) library,
+                which adds regex support to some commands, as for
+                example "env grep" and "setexpr".
+

 - Device tree:
                CONFIG_OF_CONTROL
                If this variable is defined, U-Boot will use a device tree
 - Device tree:
                CONFIG_OF_CONTROL
                If this variable is defined, U-Boot will use a device tree


@@ -1188,7 +1209,23 @@ The following options need to be configured:
                        If this option is set, the driver enables cache flush.
 
 - TPM Support:
                        If this option is set, the driver enables cache flush.
 
 - TPM Support:

-               CONFIG_GENERIC_LPC_TPM
+               CONFIG_TPM
+               Support TPM devices.
+
+               CONFIG_TPM_TIS_I2C
+               Support for i2c bus TPM devices. Only one device
+               per system is supported at this time.
+
+                       CONFIG_TPM_TIS_I2C_BUS_NUMBER
+                       Define the the i2c bus number for the TPM device
+
+                       CONFIG_TPM_TIS_I2C_SLAVE_ADDRESS
+                       Define the TPM's address on the i2c bus
+
+                       CONFIG_TPM_TIS_I2C_BURST_LIMITATION
+                       Define the burst count bytes upper limit
+
+               CONFIG_TPM_TIS_LPC

                Support for generic parallel port TPM devices. Only one device
                per system is supported at this time.
 
                Support for generic parallel port TPM devices. Only one device
                per system is supported at this time.
 


@@ -1323,6 +1360,29 @@ The following options need to be configured:
                        CONFIG_SH_MMCIF_CLK
                        Define the clock frequency for MMCIF
 
                        CONFIG_SH_MMCIF_CLK
                        Define the clock frequency for MMCIF
 

+- USB Device Firmware Update (DFU) class support:
+               CONFIG_DFU_FUNCTION
+               This enables the USB portion of the DFU USB class
+
+               CONFIG_CMD_DFU
+               This enables the command "dfu" which is used to have
+               U-Boot create a DFU class device via USB.  This command
+               requires that the "dfu_alt_info" environment variable be
+               set and define the alt settings to expose to the host.
+
+               CONFIG_DFU_MMC
+               This enables support for exposing (e)MMC devices via DFU.
+
+               CONFIG_DFU_NAND
+               This enables support for exposing NAND devices via DFU.
+
+               CONFIG_SYS_DFU_MAX_FILE_SIZE
+               When updating files rather than the raw storage device,
+               we use a static buffer to copy the file into and then write
+               the buffer once we've been given the whole file.  Define
+               this to the maximum filesize (in bytes) for the buffer.
+               Default is 4 MiB if undefined.
+

 - Journaling Flash filesystem support:
                CONFIG_JFFS2_NAND, CONFIG_JFFS2_NAND_OFF, CONFIG_JFFS2_NAND_SIZE,
                CONFIG_JFFS2_NAND_DEV
 - Journaling Flash filesystem support:
                CONFIG_JFFS2_NAND, CONFIG_JFFS2_NAND_OFF, CONFIG_JFFS2_NAND_SIZE,
                CONFIG_JFFS2_NAND_DEV


@@ -1530,6 +1590,17 @@ CBFS (Coreboot Filesystem) support
                allows for a "silent" boot where a splash screen is
                loaded very quickly after power-on.
 
                allows for a "silent" boot where a splash screen is
                loaded very quickly after power-on.
 

+               CONFIG_SPLASHIMAGE_GUARD
+
+               If this option is set, then U-Boot will prevent the environment
+               variable "splashimage" from being set to a problematic address
+               (see README.displaying-bmps and README.arm-unaligned-accesses).
+               This option is useful for targets where, due to alignment
+               restrictions, an improperly aligned BMP image will cause a data
+               abort. If you think you will not have problems with unaligned
+               accesses (for example because your toolchain prevents them)
+               there is no need to set this option.
+

                CONFIG_SPLASH_SCREEN_ALIGN
 
                If this option is set the splash image can be freely positioned
                CONFIG_SPLASH_SCREEN_ALIGN
 
                If this option is set the splash image can be freely positioned


@@ -1550,6 +1621,14 @@ CBFS (Coreboot Filesystem) support
                        => vertically centered image
                           at x = dspWidth - bmpWidth - 9
 
                        => vertically centered image
                           at x = dspWidth - bmpWidth - 9
 

+               CONFIG_SPLASH_SCREEN_PREPARE
+
+               If this option is set then the board_splash_screen_prepare()
+               function, which must be defined in your code, is called as part
+               of the splash screen display sequence. It gives the board an
+               opportunity to prepare the splash image data before it is
+               processed and sent to the frame buffer by U-Boot.
+

 - Gzip compressed BMP image support: CONFIG_VIDEO_BMP_GZIP
 
                If this option is set, additionally to standard BMP
 - Gzip compressed BMP image support: CONFIG_VIDEO_BMP_GZIP
 
                If this option is set, additionally to standard BMP


@@ -1905,15 +1984,15 @@ CBFS (Coreboot Filesystem) support
 
                I2C_READ
 
 
                I2C_READ
 

-               Code that returns TRUE if the I2C data line is high,
-               FALSE if it is low.
+               Code that returns true if the I2C data line is high,
+               false if it is low.

 
                eg: #define I2C_READ ((immr->im_cpm.cp_pbdat & PB_SDA) != 0)
 
                I2C_SDA(bit)
 
 
                eg: #define I2C_READ ((immr->im_cpm.cp_pbdat & PB_SDA) != 0)
 
                I2C_SDA(bit)
 

-               If <bit> is TRUE, sets the I2C data line high. If it
-               is FALSE, it clears it (low).
+               If <bit> is true, sets the I2C data line high. If it
+               is false, it clears it (low).

 
                eg: #define I2C_SDA(bit) \
                        if(bit) immr->im_cpm.cp_pbdat |=  PB_SDA; \
 
                eg: #define I2C_SDA(bit) \
                        if(bit) immr->im_cpm.cp_pbdat |=  PB_SDA; \


@@ -1921,8 +2000,8 @@ CBFS (Coreboot Filesystem) support
 
                I2C_SCL(bit)
 
 
                I2C_SCL(bit)
 

-               If <bit> is TRUE, sets the I2C clock line high. If it
-               is FALSE, it clears it (low).
+               If <bit> is true, sets the I2C clock line high. If it
+               is false, it clears it (low).

 
                eg: #define I2C_SCL(bit) \
                        if(bit) immr->im_cpm.cp_pbdat |=  PB_SCL; \
 
                eg: #define I2C_SCL(bit) \
                        if(bit) immr->im_cpm.cp_pbdat |=  PB_SCL; \


@@ -2743,6 +2822,32 @@ FIT uImage format:
                Adds the MTD partitioning infrastructure from the Linux
                kernel. Needed for UBI support.
 
                Adds the MTD partitioning infrastructure from the Linux
                kernel. Needed for UBI support.
 

+- UBI support
+               CONFIG_CMD_UBI
+
+               Adds commands for interacting with MTD partitions formatted
+               with the UBI flash translation layer
+
+               Requires also defining CONFIG_RBTREE
+
+               CONFIG_UBI_SILENCE_MSG
+
+               Make the verbose messages from UBI stop printing.  This leaves
+               warnings and errors enabled.
+
+- UBIFS support
+               CONFIG_CMD_UBIFS
+
+               Adds commands for interacting with UBI volumes formatted as
+               UBIFS.  UBIFS is read-only in u-boot.
+
+               Requires UBI support as well as CONFIG_LZO
+
+               CONFIG_UBIFS_SILENCE_MSG
+
+               Make the verbose messages from UBIFS stop printing.  This leaves
+               warnings and errors enabled.
+

 - SPL framework
                CONFIG_SPL
                Enable building of SPL globally.
 - SPL framework
                CONFIG_SPL
                Enable building of SPL globally.


@@ -2750,8 +2855,18 @@ FIT uImage format:
                CONFIG_SPL_LDSCRIPT
                LDSCRIPT for linking the SPL binary.
 
                CONFIG_SPL_LDSCRIPT
                LDSCRIPT for linking the SPL binary.
 

+               CONFIG_SPL_MAX_FOOTPRINT
+               Maximum size in memory allocated to the SPL, BSS included.
+               When defined, the linker checks that the actual memory
+               used by SPL from _start to __bss_end does not exceed it.
+               CONFIG_SPL_MAX_FOOTPRINT and CONFIG_SPL_BSS_MAX_SIZE
+               must not be both defined at the same time.
+

                CONFIG_SPL_MAX_SIZE
                CONFIG_SPL_MAX_SIZE

-               Maximum binary size (text, data and rodata) of the SPL binary.
+               Maximum size of the SPL image (text, data, rodata, and
+               linker lists sections), BSS excluded.
+               When defined, the linker checks that the actual size does
+               not exceed it.

 
                CONFIG_SPL_TEXT_BASE
                TEXT_BASE for linking the SPL binary.
 
                CONFIG_SPL_TEXT_BASE
                TEXT_BASE for linking the SPL binary.


@@ -2764,7 +2879,11 @@ FIT uImage format:
                Link address for the BSS within the SPL binary.
 
                CONFIG_SPL_BSS_MAX_SIZE
                Link address for the BSS within the SPL binary.
 
                CONFIG_SPL_BSS_MAX_SIZE

-               Maximum binary size of the BSS section of the SPL binary.
+               Maximum size in memory allocated to the SPL BSS.
+               When defined, the linker checks that the actual memory used
+               by SPL from __bss_start to __bss_end does not exceed it.
+               CONFIG_SPL_MAX_FOOTPRINT and CONFIG_SPL_BSS_MAX_SIZE
+               must not be both defined at the same time.

 
                CONFIG_SPL_STACK
                Adress of the start of the stack SPL will use
 
                CONFIG_SPL_STACK
                Adress of the start of the stack SPL will use


@@ -2813,12 +2932,36 @@ FIT uImage format:
                Address, size and partition on the MMC to load U-Boot from
                when the MMC is being used in raw mode.
 
                Address, size and partition on the MMC to load U-Boot from
                when the MMC is being used in raw mode.
 

+               CONFIG_SYS_MMCSD_RAW_MODE_KERNEL_SECTOR
+               Sector to load kernel uImage from when MMC is being
+               used in raw mode (for Falcon mode)
+
+               CONFIG_SYS_MMCSD_RAW_MODE_ARGS_SECTOR,
+               CONFIG_SYS_MMCSD_RAW_MODE_ARGS_SECTORS
+               Sector and number of sectors to load kernel argument
+               parameters from when MMC is being used in raw mode
+               (for falcon mode)
+

                CONFIG_SPL_FAT_SUPPORT
                Support for fs/fat/libfat.o in SPL binary
 
                CONFIG_SPL_FAT_LOAD_PAYLOAD_NAME
                Filename to read to load U-Boot when reading from FAT
 
                CONFIG_SPL_FAT_SUPPORT
                Support for fs/fat/libfat.o in SPL binary
 
                CONFIG_SPL_FAT_LOAD_PAYLOAD_NAME
                Filename to read to load U-Boot when reading from FAT
 

+               CONFIG_SPL_FAT_LOAD_KERNEL_NAME
+               Filename to read to load kernel uImage when reading
+               from FAT (for Falcon mode)
+
+               CONFIG_SPL_FAT_LOAD_ARGS_NAME
+               Filename to read to load kernel argument parameters
+               when reading from FAT (for Falcon mode)
+
+               CONFIG_SPL_MPC83XX_WAIT_FOR_NAND
+               Set this for NAND SPL on PPC mpc83xx targets, so that
+               start.S waits for the rest of the SPL to load before
+               continuing (the hardware starts execution after just
+               loading the first page rather than the full 4K).
+

                CONFIG_SPL_NAND_BASE
                Include nand_base.c in the SPL.  Requires
                CONFIG_SPL_NAND_DRIVERS.
                CONFIG_SPL_NAND_BASE
                Include nand_base.c in the SPL.  Requires
                CONFIG_SPL_NAND_DRIVERS.


@@ -2876,11 +3019,24 @@ FIT uImage format:
                CONFIG_SPL_LIBGENERIC_SUPPORT
                Support for lib/libgeneric.o in SPL binary
 
                CONFIG_SPL_LIBGENERIC_SUPPORT
                Support for lib/libgeneric.o in SPL binary
 

+               CONFIG_SPL_PAD_TO
+               Image offset to which the SPL should be padded before appending
+               the SPL payload. By default, this is defined as
+               CONFIG_SPL_MAX_SIZE, or 0 if CONFIG_SPL_MAX_SIZE is undefined.
+               CONFIG_SPL_PAD_TO must be either 0, meaning to append the SPL
+               payload without any padding, or >= CONFIG_SPL_MAX_SIZE.
+

                CONFIG_SPL_TARGET
                Final target image containing SPL and payload.  Some SPLs
                use an arch-specific makefile fragment instead, for
                example if more than one image needs to be produced.
 
                CONFIG_SPL_TARGET
                Final target image containing SPL and payload.  Some SPLs
                use an arch-specific makefile fragment instead, for
                example if more than one image needs to be produced.
 

+               CONFIG_FIT_SPL_PRINT
+               Printing information about a FIT image adds quite a bit of
+               code to SPL. So this is normally disabled in SPL. Use this
+               option to re-enable it. This will affect the output of the
+               bootm command when booting a FIT image.
+

 Modem Support:
 --------------
 
 Modem Support:
 --------------
 


@@ -3140,6 +3296,15 @@ Configuration Settings:
                digits and dots.  Recommended value: 45 (9..1) for 80
                column displays, 15 (3..1) for 40 column displays.
 
                digits and dots.  Recommended value: 45 (9..1) for 80
                column displays, 15 (3..1) for 40 column displays.
 

+- CONFIG_FLASH_VERIFY
+               If defined, the content of the flash (destination) is compared
+               against the source after the write operation. An error message
+               will be printed when the contents are not identical.
+               Please note that this option is useless in nearly all cases,
+               since such flash programming errors usually are detected earlier
+               while unprotecting/erasing/programming. Please only enable
+               this option if you really know what you are doing.
+

 - CONFIG_SYS_RX_ETH_BUFFER:
                Defines the number of Ethernet receive buffers. On some
                Ethernet controllers it is recommended to set this value
 - CONFIG_SYS_RX_ETH_BUFFER:
                Defines the number of Ethernet receive buffers. On some
                Ethernet controllers it is recommended to set this value


@@ -3199,6 +3364,27 @@ Configuration Settings:
        If defined, don't allow the -f switch to env set override variable
        access flags.
 
        If defined, don't allow the -f switch to env set override variable
        access flags.
 

+- CONFIG_SYS_GENERIC_BOARD
+       This selects the architecture-generic board system instead of the
+       architecture-specific board files. It is intended to move boards
+       to this new framework over time. Defining this will disable the
+       arch/foo/lib/board.c file and use common/board_f.c and
+       common/board_r.c instead. To use this option your architecture
+       must support it (i.e. must define __HAVE_ARCH_GENERIC_BOARD in
+       its config.mk file). If you find problems enabling this option on
+       your board please report the problem and send patches!
+
+- CONFIG_SYS_SYM_OFFSETS
+       This is set by architectures that use offsets for link symbols
+       instead of absolute values. So bss_start is obtained using an
+       offset _bss_start_ofs from CONFIG_SYS_TEXT_BASE, rather than
+       directly. You should not need to touch this setting.
+
+- CONFIG_OMAP_PLATFORM_RESET_TIME_MAX_USEC (OMAP only)
+       This is set by OMAP boards for the max time that reset should
+       be asserted. See doc/README.omap-reset-time for details on how
+       the value can be calulated on a given board.
+

 The following definitions that deal with the placement and management
 of environment data (variable area); in general, we support the
 following configurations:
 The following definitions that deal with the placement and management
 of environment data (variable area); in general, we support the
 following configurations:


@@ -3432,6 +3618,33 @@ but it can not erase, write this NOR flash by SRIO or PCIE interface.
        environment. If redundant environment is used, it will be copied to
        CONFIG_NAND_ENV_DST + CONFIG_ENV_SIZE.
 
        environment. If redundant environment is used, it will be copied to
        CONFIG_NAND_ENV_DST + CONFIG_ENV_SIZE.
 

+- CONFIG_ENV_IS_IN_UBI:
+
+       Define this if you have an UBI volume that you want to use for the
+       environment.  This has the benefit of wear-leveling the environment
+       accesses, which is important on NAND.
+
+       - CONFIG_ENV_UBI_PART:
+
+         Define this to a string that is the mtd partition containing the UBI.
+
+       - CONFIG_ENV_UBI_VOLUME:
+
+         Define this to the name of the volume that you want to store the
+         environment in.
+
+       - CONFIG_ENV_UBI_VOLUME_REDUND:
+
+         Define this to the name of another volume to store a second copy of
+         the environment in.  This will enable redundant environments in UBI.
+         It is assumed that both volumes are in the same MTD partition.
+
+       - CONFIG_UBI_SILENCE_MSG
+       - CONFIG_UBIFS_SILENCE_MSG
+
+         You will probably want to define these to avoid a really noisy system
+         when storing the env in UBI.
+

 - CONFIG_SYS_SPI_INIT_OFFSET
 
        Defines offset to the initial SPI buffer area in DPRAM. The
 - CONFIG_SYS_SPI_INIT_OFFSET
 
        Defines offset to the initial SPI buffer area in DPRAM. The


@@ -3685,6 +3898,9 @@ Low Level (hardware related) configuration options:
                a second time.  Useful for platforms that are pre-booted
                by coreboot or similar.
 
                a second time.  Useful for platforms that are pre-booted
                by coreboot or similar.
 

+- CONFIG_PCI_INDIRECT_BRIDGE:
+               Enable support for indirect PCI bridges.
+

 - CONFIG_SYS_SRIO:
                Chip has SRIO or not
 
 - CONFIG_SYS_SRIO:
                Chip has SRIO or not
 


@@ -3703,9 +3919,13 @@ Low Level (hardware related) configuration options:
 - CONFIG_SYS_SRIOn_MEM_SIZE:
                Size of SRIO port 'n' memory region
 
 - CONFIG_SYS_SRIOn_MEM_SIZE:
                Size of SRIO port 'n' memory region
 

-- CONFIG_SYS_NDFC_16
-               Defined to tell the NDFC that the NAND chip is using a
-               16 bit bus.
+- CONFIG_SYS_NAND_BUSWIDTH_16BIT
+               Defined to tell the NAND controller that the NAND chip is using
+               a 16 bit bus.
+               Not all NAND drivers use this symbol.
+               Example of drivers that use it:
+               - drivers/mtd/nand/ndfc.c
+               - drivers/mtd/nand/mxc_nand.c

 
 - CONFIG_SYS_NDFC_EBC0_CFG
                Sets the EBC0_CFG register for the NDFC. If not defined
 
 - CONFIG_SYS_NDFC_EBC0_CFG
                Sets the EBC0_CFG register for the NDFC. If not defined


@@ -3800,21 +4020,29 @@ Low Level (hardware related) configuration options:
                that is executed before the actual U-Boot. E.g. when
                compiling a NAND SPL.
 
                that is executed before the actual U-Boot. E.g. when
                compiling a NAND SPL.
 

+- CONFIG_ARCH_MAP_SYSMEM
+               Generally U-Boot (and in particular the md command) uses
+               effective address. It is therefore not necessary to regard
+               U-Boot address as virtual addresses that need to be translated
+               to physical addresses. However, sandbox requires this, since
+               it maintains its own little RAM buffer which contains all
+               addressable memory. This option causes some memory accesses
+               to be mapped through map_sysmem() / unmap_sysmem().
+

 - CONFIG_USE_ARCH_MEMCPY
   CONFIG_USE_ARCH_MEMSET
                If these options are used a optimized version of memcpy/memset will
                be used if available. These functions may be faster under some
                conditions but may increase the binary size.
 
 - CONFIG_USE_ARCH_MEMCPY
   CONFIG_USE_ARCH_MEMSET
                If these options are used a optimized version of memcpy/memset will
                be used if available. These functions may be faster under some
                conditions but may increase the binary size.
 

-- CONFIG_X86_NO_RESET_VECTOR
-               If defined, the x86 reset vector code is excluded. You will need
-               to do this when U-Boot is running from Coreboot.
+- CONFIG_X86_RESET_VECTOR
+               If defined, the x86 reset vector code is included. This is not
+               needed when U-Boot is running from Coreboot.

 
 

-- CONFIG_X86_NO_REAL_MODE
-               If defined, x86 real mode code is omitted. This assumes a
-               32-bit environment where such code is not needed. You will
-               need to do this when U-Boot is running from Coreboot.
+- CONFIG_SYS_MPUCLK
+               Defines the MPU clock speed (in MHz).

 
 

+               NOTE : currently only supported on AM335x platforms.

 
 Freescale QE/FMAN Firmware Support:
 -----------------------------------
 
 Freescale QE/FMAN Firmware Support:
 -----------------------------------


@@ -4877,7 +5105,7 @@ On some platforms, it's possible to boot Linux zImage. This is done
 using the "bootz" command. The syntax of "bootz" command is the same
 as the syntax of "bootm" command.
 
 using the "bootz" command. The syntax of "bootz" command is the same
 as the syntax of "bootm" command.
 

-Note, defining the CONFIG_SUPPORT_INITRD_RAW allows user to supply
+Note, defining the CONFIG_SUPPORT_RAW_INITRD allows user to supply

 kernel with raw initrd images. The syntax is slightly different, the
 address of the initrd must be augmented by it's size, in the following
 format: "<initrd addres>:<initrd size>".
 kernel with raw initrd images. The syntax is slightly different, the
 address of the initrd must be augmented by it's size, in the following
 format: "<initrd addres>:<initrd size>".