remove useless type casts

[karo-tx-uboot.git] / README

diff --git a/README b/README
index 9702067174e361eb94383839e984d9ae6df4075c..6919392dca82c142ea00d9281393ddcde33ae981 100644 (file)
--- a/README
+++ b/README
@@ -432,6 +432,14 @@ The following options need to be configured:
                Select high exception vectors of the ARM core, e.g., do not
                clear the V bit of the c1 register of CP15.
 
                Select high exception vectors of the ARM core, e.g., do not
                clear the V bit of the c1 register of CP15.
 

+               CONFIG_SYS_THUMB_BUILD
+
+               Use this flag to build U-Boot using the Thumb instruction
+               set for ARM architectures. Thumb instruction set provides
+               better code density. For ARM architectures that support
+               Thumb2 this flag will result in Thumb2 code generated by
+               GCC.
+

 - Linux Kernel Interface:
                CONFIG_CLOCKS_IN_MHZ
 
 - Linux Kernel Interface:
                CONFIG_CLOCKS_IN_MHZ
 


@@ -814,7 +822,7 @@ The following options need to be configured:
                CONFIG_CMD_TIME         * run command and report execution time
                CONFIG_CMD_USB          * USB support
                CONFIG_CMD_CDP          * Cisco Discover Protocol support
                CONFIG_CMD_TIME         * run command and report execution time
                CONFIG_CMD_USB          * USB support
                CONFIG_CMD_CDP          * Cisco Discover Protocol support

-               CONFIG_CMD_FSL          * Microblaze FSL support
+               CONFIG_CMD_MFSL         * Microblaze FSL support

 
 
                EXAMPLE: If you want all functions except of network
 
 
                EXAMPLE: If you want all functions except of network


@@ -3026,6 +3034,24 @@ to save the current settings.
          environment area within the total memory of your DataFlash placed
          at the specified address.
 
          environment area within the total memory of your DataFlash placed
          at the specified address.
 

+- CONFIG_ENV_IS_IN_REMOTE:
+
+       Define this if you have a remote memory space which you
+       want to use for the local device's environment.
+
+       - CONFIG_ENV_ADDR:
+       - CONFIG_ENV_SIZE:
+
+         These two #defines specify the address and size of the
+         environment area within the remote memory space. The
+         local device can get the environment from remote memory
+         space by SRIO or other links.
+
+BE CAREFUL! For some special cases, the local device can not use
+"saveenv" command. For example, the local device will get the
+environment stored in a remote NOR flash by SRIO link, but it can
+not erase, write this NOR flash by SRIO interface.
+

 - CONFIG_ENV_IS_IN_NAND:
 
        Define this if you have a NAND device which you want to use
 - CONFIG_ENV_IS_IN_NAND:
 
        Define this if you have a NAND device which you want to use


@@ -3462,6 +3488,12 @@ within that device.
        Specifies that QE/FMAN firmware is located on the primary SPI
        device.  CONFIG_SYS_FMAN_FW_ADDR is the byte offset on that device.
 
        Specifies that QE/FMAN firmware is located on the primary SPI
        device.  CONFIG_SYS_FMAN_FW_ADDR is the byte offset on that device.
 

+- CONFIG_SYS_QE_FMAN_FW_IN_REMOTE
+       Specifies that QE/FMAN firmware is located in the remote (master)
+       memory space.   CONFIG_SYS_FMAN_FW_ADDR is a virtual address which
+       can be mapped from slave TLB->slave LAW->slave SRIO outbound window
+       ->master inbound window->master LAW->the ucode address in master's
+       NOR flash.

 
 Building the Software:
 ======================
 
 Building the Software:
 ======================


@@ -3499,7 +3531,7 @@ is done by typing:
        make NAME_config
 
 where "NAME_config" is the name of one of the existing configu-
        make NAME_config
 
 where "NAME_config" is the name of one of the existing configu-

-rations; see the main Makefile for supported names.
+rations; see boards.cfg for supported names.

 
 Note: for some board special configuration names may exist; check if
       additional information is available from the board vendor; for
 
 Note: for some board special configuration names may exist; check if
       additional information is available from the board vendor; for


@@ -3554,10 +3586,8 @@ to port U-Boot to your hardware platform. To do this, follow these
 steps:
 
 1.  Add a new configuration option for your board to the toplevel
 steps:
 
 1.  Add a new configuration option for your board to the toplevel

-    "Makefile" and to the "MAKEALL" script, using the existing
-    entries as examples. Note that here and at many other places
-    boards and other names are listed in alphabetical sort order. Please
-    keep this order.
+    "boards.cfg" file, using the existing entries as examples.
+    Follow the instructions there to keep the boards in order.

 2.  Create a new directory to hold your board specific code. Add any
     files you need. In your board directory, you will need at least
     the "Makefile", a "<board>.c", "flash.c" and "u-boot.lds".
 2.  Create a new directory to hold your board specific code. Add any
     files you need. In your board directory, you will need at least
     the "Makefile", a "<board>.c", "flash.c" and "u-boot.lds".