+config SPL_FEL
+ bool "SPL/FEL mode support"
+ depends on SPL
+ default n
+
+config UART0_PORT_F
+ bool "UART0 on MicroSD breakout board"
+ depends on SPL_FEL
+ default n
+ ---help---
+ Repurpose the SD card slot for getting access to the UART0 serial
+ console. Primarily useful only for low level u-boot debugging on
+ tablets, where normal UART0 is difficult to access and requires
+ device disassembly and/or soldering. As the SD card can't be used
+ at the same time, the system can be only booted in the FEL mode.
+ Only enable this if you really know what you are doing.
+
+config FDTFILE
+ string "Default fdtfile env setting for this board"
+
+config OLD_SUNXI_KERNEL_COMPAT
+ boolean "Enable workarounds for booting old kernels"
+ default n
+ ---help---
+ Set this to enable various workarounds for old kernels, this results in
+ sub-optimal settings for newer kernels, only enable if needed.
+
+config MMC0_CD_PIN
+ string "Card detect pin for mmc0"
+ default ""
+ ---help---
+ Set the card detect pin for mmc0, leave empty to not use cd. This
+ takes a string in the format understood by sunxi_name_to_gpio, e.g.
+ PH1 for pin 1 of port H.
+
+config MMC1_CD_PIN
+ string "Card detect pin for mmc1"
+ default ""
+ ---help---
+ See MMC0_CD_PIN help text.
+
+config MMC2_CD_PIN
+ string "Card detect pin for mmc2"
+ default ""
+ ---help---
+ See MMC0_CD_PIN help text.
+
+config MMC3_CD_PIN
+ string "Card detect pin for mmc3"
+ default ""
+ ---help---
+ See MMC0_CD_PIN help text.
+
+config MMC_SUNXI_SLOT_EXTRA
+ int "mmc extra slot number"
+ default -1
+ ---help---
+ sunxi builds always enable mmc0, some boards also have a second sdcard
+ slot or emmc on mmc1 - mmc3. Setting this to 1, 2 or 3 will enable
+ support for this.
+
+config USB1_VBUS_PIN
+ string "Vbus enable pin for usb1 (ehci0)"
+ default "PH6" if MACH_SUN4I || MACH_SUN7I
+ default "PH27" if MACH_SUN6I
+ ---help---
+ Set the Vbus enable pin for usb1 (ehci0, usb0 is the otg). This takes
+ a string in the format understood by sunxi_name_to_gpio, e.g.
+ PH1 for pin 1 of port H.
+
+config USB2_VBUS_PIN
+ string "Vbus enable pin for usb2 (ehci1)"
+ default "PH3" if MACH_SUN4I || MACH_SUN7I
+ default "PH24" if MACH_SUN6I
+ ---help---
+ See USB1_VBUS_PIN help text.
+
+config VIDEO
+ boolean "Enable graphical uboot console on HDMI, LCD or VGA"
+ default y
+ ---help---
+ Say Y here to add support for using a cfb console on the HDMI, LCD
+ or VGA output found on most sunxi devices. See doc/README.video for
+ info on how to select the video output and mode.
+
+config VIDEO_HDMI
+ boolean "HDMI output support"
+ depends on VIDEO && !MACH_SUN8I
+ default y
+ ---help---
+ Say Y here to add support for outputting video over HDMI.
+
+config VIDEO_VGA
+ boolean "VGA output support"
+ depends on VIDEO && (MACH_SUN4I || MACH_SUN7I)
+ default n
+ ---help---
+ Say Y here to add support for outputting video over VGA.
+
+config VIDEO_VGA_VIA_LCD
+ boolean "VGA via LCD controller support"
+ depends on VIDEO && MACH_SUN5I
+ default n
+ ---help---
+ Say Y here to add support for external DACs connected to the parallel
+ LCD interface driving a VGA connector, such as found on the
+ Olimex A13 boards.
+
+config VIDEO_LCD_MODE
+ string "LCD panel timing details"
+ depends on VIDEO
+ default ""
+ ---help---
+ LCD panel timing details string, leave empty if there is no LCD panel.
+ This is in drivers/video/videomodes.c: video_get_params() format, e.g.
+ x:800,y:480,depth:18,pclk_khz:33000,le:16,ri:209,up:22,lo:22,hs:30,vs:1,sync:0,vmode:0
+
+config VIDEO_LCD_POWER
+ string "LCD panel power enable pin"
+ depends on VIDEO
+ default ""
+ ---help---
+ Set the power enable pin for the LCD panel. This takes a string in the
+ format understood by sunxi_name_to_gpio, e.g. PH1 for pin 1 of port H.
+
+config VIDEO_LCD_BL_EN
+ string "LCD panel backlight enable pin"
+ depends on VIDEO
+ default ""
+ ---help---
+ Set the backlight enable pin for the LCD panel. This takes a string in the
+ the format understood by sunxi_name_to_gpio, e.g. PH1 for pin 1 of
+ port H.
+
+config VIDEO_LCD_BL_PWM
+ string "LCD panel backlight pwm pin"
+ depends on VIDEO
+ default ""
+ ---help---
+ Set the backlight pwm pin for the LCD panel. This takes a string in the
+ format understood by sunxi_name_to_gpio, e.g. PH1 for pin 1 of port H.
+
+config USB_KEYBOARD
+ boolean "Enable USB keyboard support"
+ default y
+ ---help---
+ Say Y here to add support for using a USB keyboard (typically used
+ in combination with a graphical console).