====================
/arch Architecture specific files
+ /arc Files generic to ARC architecture
+ /cpu CPU specific files
+ /arc700 Files specific to ARC 700 CPUs
+ /lib Architecture specific library files
/arm Files generic to ARM architecture
/cpu CPU specific files
/arm720t Files specific to ARM 720 CPUs
/s3c24x0 Files specific to Samsung S3C24X0 CPUs
/arm926ejs Files specific to ARM 926 CPUs
/arm1136 Files specific to ARM 1136 CPUs
- /ixp Files specific to Intel XScale IXP CPUs
/pxa Files specific to Intel XScale PXA CPUs
/sa1100 Files specific to Intel StrongARM SA1100 CPUs
/lib Architecture specific library files
/mips Files generic to MIPS architecture
/cpu CPU specific files
/mips32 Files specific to MIPS32 CPUs
- /xburst Files specific to Ingenic XBurst CPUs
+ /mips64 Files specific to MIPS64 CPUs
/lib Architecture specific library files
/nds32 Files generic to NDS32 architecture
/cpu CPU specific files
---------------------------------------------------
For all supported boards there are ready-to-use default
-configurations available; just type "make <board_name>_config".
+configurations available; just type "make <board_name>_defconfig".
Example: For a TQM823L module type:
cd u-boot
- make TQM823L_config
+ make TQM823L_defconfig
For the Cogent platform, you need to specify the CPU type as well;
-e.g. "make cogent_mpc8xx_config". And also configure the cogent
+e.g. "make cogent_mpc8xx_defconfig". And also configure the cogent
directory according to the instructions in cogent/README.
+Sandbox Environment:
+--------------------
+
+U-Boot can be built natively to run on a Linux host using the 'sandbox'
+board. This allows feature development which is not board- or architecture-
+specific to be undertaken on a native platform. The sandbox is also used to
+run some of U-Boot's tests.
+
+See board/sandbox/sandbox/README.sandbox for more details.
+
+
Configuration Options:
----------------------
the LCD display every second with
a "rotator" |\-/|\-/
-- Board flavour: (if CONFIG_MPC8260ADS is defined)
- CONFIG_ADSTYPE
- Possible values are:
- CONFIG_SYS_8260ADS - original MPC8260ADS
- CONFIG_SYS_8266ADS - MPC8266ADS
- CONFIG_SYS_PQ2FADS - PQ2FADS-ZU or PQ2FADS-VR
- CONFIG_SYS_8272ADS - MPC8272ADS
-
- Marvell Family Member
CONFIG_SYS_MVFS - define it if you want to enable
multiple fs option at one time
In this mode, a single differential clock is used to supply
clocks to the sysclock, ddrclock and usbclock.
+ CONFIG_SYS_CPC_REINIT_F
+ This CONFIG is defined when the CPC is configured as SRAM at the
+ time of U-boot entry and is required to be re-initialized.
+
+ CONFIG_DEEP_SLEEP
+ Inidcates this SoC supports deep sleep feature. If deep sleep is
+ supported, core will start to execute uboot when wakes up.
+
- Generic CPU options:
+ CONFIG_SYS_GENERIC_GLOBAL_DATA
+ Defines global data is initialized in generic board board_init_f().
+ If this macro is defined, global data is created and cleared in
+ generic board board_init_f(). Without this macro, architecture/board
+ should initialize global data before calling board_init_f().
+
CONFIG_SYS_BIG_ENDIAN, CONFIG_SYS_LITTLE_ENDIAN
Defines the endianess of the CPU. Implementation of those
CONFIG_SYS_FSL_DDRC_GEN3
Freescale DDR3 controller.
+ CONFIG_SYS_FSL_DDRC_GEN4
+ Freescale DDR4 controller.
+
CONFIG_SYS_FSL_DDRC_ARM_GEN3
Freescale DDR3 controller for ARM-based SoCs.
CONFIG_SYS_FSL_DDR3
Board config to use DDR3. It can be enabled for SoCs with
- Freescale DDR3 controllers.
+ Freescale DDR3 or DDR3L controllers.
+
+ CONFIG_SYS_FSL_DDR3L
+ Board config to use DDR3L. It can be enabled for SoCs with
+ DDR3L controllers.
+
+ CONFIG_SYS_FSL_DDR4
+ Board config to use DDR4. It can be enabled for SoCs with
+ DDR4 controllers.
+
+ CONFIG_SYS_FSL_IFC_BE
+ Defines the IFC controller register space as Big Endian
+
+ CONFIG_SYS_FSL_IFC_LE
+ Defines the IFC controller register space as Little Endian
+
+ CONFIG_SYS_FSL_PBL_PBI
+ It enables addition of RCW (Power on reset configuration) in built image.
+ Please refer doc/README.pblimage for more details
+
+ CONFIG_SYS_FSL_PBL_RCW
+ It adds PBI(pre-boot instructions) commands in u-boot build image.
+ PBI commands can be used to configure SoC before it starts the execution.
+ Please refer doc/README.pblimage for more details
+
+ CONFIG_SPL_FSL_PBL
+ It adds a target to create boot binary having SPL binary in PBI format
+ concatenated with u-boot binary.
+
+ CONFIG_SYS_FSL_DDR_BE
+ Defines the DDR controller register space as Big Endian
+
+ CONFIG_SYS_FSL_DDR_LE
+ Defines the DDR controller register space as Little Endian
+
+ CONFIG_SYS_FSL_DDR_SDRAM_BASE_PHY
+ Physical address from the view of DDR controllers. It is the
+ same as CONFIG_SYS_DDR_SDRAM_BASE for all Power SoCs. But
+ it could be different for ARM SoCs.
+
+ CONFIG_SYS_FSL_DDR_INTLV_256B
+ DDR controller interleaving on 256-byte. This is a special
+ interleaving mode, handled by Dickens for Freescale layerscape
+ SoCs with ARM core.
- Intel Monahans options:
CONFIG_SYS_MONAHANS_RUN_MODE_OSC_RATIO
CONFIG_ARM_ERRATA_742230
CONFIG_ARM_ERRATA_743622
CONFIG_ARM_ERRATA_751472
+ CONFIG_ARM_ERRATA_794072
+ CONFIG_ARM_ERRATA_761320
If set, the workarounds for these ARM errata are applied early
during U-Boot startup. Note that these options force the
boot loader that has already initialized the UART. Define this
variable to flush the UART at init time.
+ CONFIG_SERIAL_HW_FLOW_CONTROL
+
+ Define this variable to enable hw flow control in serial driver.
+ Current user of this option is drivers/serial/nsl16550.c driver
- Console Interface:
Depending on board, define exactly one serial port
The default command configuration includes all commands
except those marked below with a "*".
+ CONFIG_CMD_AES AES 128 CBC encrypt/decrypt
CONFIG_CMD_ASKENV * ask for env variable
CONFIG_CMD_BDI bdinfo
CONFIG_CMD_BEDBUG * Include BedBug Debugger
CONFIG_CMD_BMP * BMP support
CONFIG_CMD_BSP * Board specific commands
CONFIG_CMD_BOOTD bootd
+ CONFIG_CMD_BOOTI * ARM64 Linux kernel Image support
CONFIG_CMD_CACHE * icache, dcache
+ CONFIG_CMD_CLK * clock command support
CONFIG_CMD_CONSOLE coninfo
CONFIG_CMD_CRC32 * crc32
CONFIG_CMD_DATE * support for RTC, date/time...
CONFIG_CMD_EXPORTENV * export the environment
CONFIG_CMD_EXT2 * ext2 command support
CONFIG_CMD_EXT4 * ext4 command support
+ CONFIG_CMD_FS_GENERIC * filesystem commands (e.g. load, ls)
+ that work for multiple fs types
CONFIG_CMD_SAVEENV saveenv
CONFIG_CMD_FDC * Floppy Disk Support
CONFIG_CMD_FAT * FAT command support
- CONFIG_CMD_FDOS * Dos diskette Support
CONFIG_CMD_FLASH flinfo, erase, protect
CONFIG_CMD_FPGA FPGA device initialization support
CONFIG_CMD_FUSE * Device fuse support
CONFIG_CMD_IMLS List all images found in NOR flash
CONFIG_CMD_IMLS_NAND * List all images found in NAND flash
CONFIG_CMD_IMMAP * IMMR dump support
+ CONFIG_CMD_IOTRACE * I/O tracing for debugging
CONFIG_CMD_IMPORTENV * import an environment
CONFIG_CMD_INI * import data from an ini file into the env
CONFIG_CMD_IRQ * irqinfo
CONFIG_CMD_CDP * Cisco Discover Protocol support
CONFIG_CMD_MFSL * Microblaze FSL support
CONFIG_CMD_XIMG Load part of Multi Image
-
+ CONFIG_CMD_UUID * Generate random UUID or GUID string
EXAMPLE: If you want all functions except of network
support you can write:
CONFIG_RTC_DS1307 - use Maxim, Inc. DS1307 RTC
CONFIG_RTC_DS1337 - use Maxim, Inc. DS1337 RTC
CONFIG_RTC_DS1338 - use Maxim, Inc. DS1338 RTC
+ CONFIG_RTC_DS1339 - use Maxim, Inc. DS1339 RTC
CONFIG_RTC_DS164x - use Dallas DS164x RTC
CONFIG_RTC_ISL1208 - use Intersil ISL1208 RTC
CONFIG_RTC_MAX6900 - use Maxim, Inc. MAX6900 RTC
Note that if the GPIO device uses I2C, then the I2C interface
must also be configured. See I2C Support, below.
+- I/O tracing:
+ When CONFIG_IO_TRACE is selected, U-Boot intercepts all I/O
+ accesses and can checksum them or write a list of them out
+ to memory. See the 'iotrace' command for details. This is
+ useful for testing device drivers since it can confirm that
+ the driver behaves the same way before and after a code
+ change. Currently this is supported on sandbox and arm. To
+ add support for your architecture, add '#include <iotrace.h>'
+ to the bottom of arch/<arch>/include/asm/io.h and test.
+
+ Example output from the 'iotrace stats' command is below.
+ Note that if the trace buffer is exhausted, the checksum will
+ still continue to operate.
+
+ iotrace is enabled
+ Start: 10000000 (buffer start address)
+ Size: 00010000 (buffer size)
+ Offset: 00000120 (current buffer offset)
+ Output: 10000120 (start + offset)
+ Count: 00000018 (number of trace records)
+ CRC32: 9526fb66 (CRC32 of all trace records)
+
- Timestamp Support:
When CONFIG_TIMESTAMP is selected, the timestamp
CONFIG_SH_ETHER_CACHE_WRITEBACK
If this option is set, the driver enables cache flush.
+- PWM Support:
+ CONFIG_PWM_IMX
+ Support for PWM modul on the imx6.
+
- TPM Support:
CONFIG_TPM
Support TPM devices.
CONFIG_USB_EHCI_TXFIFO_THRESH enables setting of the
txfilltuning field in the EHCI controller on reset.
- CONFIG_USB_HUB_MIN_POWER_ON_DELAY defines the minimum
- interval for usb hub power-on delay.(minimum 100msec)
-
- USB Device:
Define the below if you wish to use the USB console.
Once firmware is rebuilt from a serial console issue the
for your device
- CONFIG_USBD_PRODUCTID 0xFFFF
- Some USB device drivers may need to check USB cable attachment.
- In this case you can enable following config in BoardName.h:
- CONFIG_USB_CABLE_CHECK
- This enables function definition:
- - usb_cable_connected() in include/usb.h
- Implementation of this function is board-specific.
-
- ULPI Layer Support:
The ULPI (UTMI Low Pin (count) Interface) PHYs are supported via
the generic ULPI layer. The generic layer accesses the ULPI PHY
CONFIG_SH_MMCIF_CLK
Define the clock frequency for MMCIF
+ CONFIG_GENERIC_MMC
+ Enable the generic MMC driver
+
+ CONFIG_SUPPORT_EMMC_BOOT
+ Enable some additional features of the eMMC boot partitions.
+
+ CONFIG_SUPPORT_EMMC_RPMB
+ Enable the commands for reading, writing and programming the
+ key for the Replay Protection Memory Block partition in eMMC.
+
- USB Device Firmware Update (DFU) class support:
CONFIG_DFU_FUNCTION
This enables the USB portion of the DFU USB class
this to the maximum filesize (in bytes) for the buffer.
Default is 4 MiB if undefined.
+ DFU_DEFAULT_POLL_TIMEOUT
+ Poll timeout [ms], is the timeout a device can send to the
+ host. The host must wait for this timeout before sending
+ a subsequent DFU_GET_STATUS request to the device.
+
+ DFU_MANIFEST_POLL_TIMEOUT
+ Poll timeout [ms], which the device sends to the host when
+ entering dfuMANIFEST state. Host waits this timeout, before
+ sending again an USB request to the device.
+
+- USB Device Android Fastboot support:
+ CONFIG_CMD_FASTBOOT
+ This enables the command "fastboot" which enables the Android
+ fastboot mode for the platform's USB device. Fastboot is a USB
+ protocol for downloading images, flashing and device control
+ used on Android devices.
+ See doc/README.android-fastboot for more information.
+
+ CONFIG_ANDROID_BOOT_IMAGE
+ This enables support for booting images which use the Android
+ image format header.
+
+ CONFIG_USB_FASTBOOT_BUF_ADDR
+ The fastboot protocol requires a large memory buffer for
+ downloads. Define this to the starting RAM address to use for
+ downloaded images.
+
+ CONFIG_USB_FASTBOOT_BUF_SIZE
+ The fastboot protocol requires a large memory buffer for
+ downloads. This buffer should be as large as possible for a
+ platform. Define this to the size available RAM for fastboot.
+
- Journaling Flash filesystem support:
CONFIG_JFFS2_NAND, CONFIG_JFFS2_NAND_OFF, CONFIG_JFFS2_NAND_SIZE,
CONFIG_JFFS2_NAND_DEV
filesystem. Available commands are cbfsinit, cbfsinfo, cbfsls
and cbfsload.
+- FAT(File Allocation Table) filesystem cluster size:
+ CONFIG_FS_FAT_MAX_CLUSTSIZE
+
+ Define the max cluster size for fat operations else
+ a default value of 65536 will be defined.
+
- Keyboard Support:
CONFIG_ISA_KEYBOARD
If this option is set, then U-Boot will prevent the environment
variable "splashimage" from being set to a problematic address
- (see README.displaying-bmps and README.arm-unaligned-accesses).
+ (see README.displaying-bmps).
This option is useful for targets where, due to alignment
restrictions, an improperly aligned BMP image will cause a data
abort. If you think you will not have problems with unaligned
4th and following
BOOTP requests: delay 0 ... 8 sec
+ CONFIG_BOOTP_ID_CACHE_SIZE
+
+ BOOTP packets are uniquely identified using a 32-bit ID. The
+ server will copy the ID from client requests to responses and
+ U-Boot will use this to determine if it is the destination of
+ an incoming response. Some servers will check that addresses
+ aren't in use before handing them out (usually using an ARP
+ ping) and therefore take up to a few hundred milliseconds to
+ respond. Network congestion may also influence the time it
+ takes for a response to make it back to the client. If that
+ time is too long, U-Boot will retransmit requests. In order
+ to allow earlier responses to still be accepted after these
+ retransmissions, U-Boot's BOOTP client keeps a small cache of
+ IDs. The CONFIG_BOOTP_ID_CACHE_SIZE controls the size of this
+ cache. The default is to keep IDs for up to four outstanding
+ requests. Increasing this will allow U-Boot to accept offers
+ from a BOOTP client in networks with unusually high latency.
+
- DHCP Advanced Options:
You can fine tune the DHCP functionality by defining
CONFIG_BOOTP_* symbols:
9 i2c buses for Exynos4 and 1 for S3C24X0 SoCs from Samsung)
with a fix speed from 100000 and the slave addr 0!
+ - drivers/i2c/ihs_i2c.c
+ - activate this driver with CONFIG_SYS_I2C_IHS
+ - CONFIG_SYS_I2C_IHS_CH0 activate hardware channel 0
+ - CONFIG_SYS_I2C_IHS_SPEED_0 speed channel 0
+ - CONFIG_SYS_I2C_IHS_SLAVE_0 slave addr channel 0
+ - CONFIG_SYS_I2C_IHS_CH1 activate hardware channel 1
+ - CONFIG_SYS_I2C_IHS_SPEED_1 speed channel 1
+ - CONFIG_SYS_I2C_IHS_SLAVE_1 slave addr channel 1
+ - CONFIG_SYS_I2C_IHS_CH2 activate hardware channel 2
+ - CONFIG_SYS_I2C_IHS_SPEED_2 speed channel 2
+ - CONFIG_SYS_I2C_IHS_SLAVE_2 slave addr channel 2
+ - CONFIG_SYS_I2C_IHS_CH3 activate hardware channel 3
+ - CONFIG_SYS_I2C_IHS_SPEED_3 speed channel 3
+ - CONFIG_SYS_I2C_IHS_SLAVE_3 slave addr channel 3
+
additional defines:
CONFIG_SYS_NUM_I2C_BUSES
Enables the driver for the SPI controllers on i.MX and MXC
SoCs. Currently i.MX31/35/51 are supported.
+ CONFIG_SYS_SPI_MXC_WAIT
+ Timeout for waiting until spi transfer completed.
+ default: (CONFIG_SYS_HZ/100) /* 10 ms */
+
- FPGA Support: CONFIG_FPGA
Enables FPGA subsystem.
Specify the number of FPGA devices to support.
+ CONFIG_CMD_FPGA_LOADMK
+
+ Enable support for fpga loadmk command
+
+ CONFIG_CMD_FPGA_LOADP
+
+ Enable support for fpga loadp command - load partial bitstream
+
+ CONFIG_CMD_FPGA_LOADBP
+
+ Enable support for fpga loadbp command - load partial bitstream
+ (Xilinx only)
+
CONFIG_SYS_FPGA_PROG_FEEDBACK
Enable printing of hash marks during FPGA configuration.
Define this option to use the Bank addr/Extended addr
support on SPI flashes which has size > 16Mbytes.
+ CONFIG_SF_DUAL_FLASH Dual flash memories
+
+ Define this option to use dual flash support where two flash
+ memories can be connected with a given cs line.
+ currently Xilinx Zynq qspi support these type of connections.
+
+ CONFIG_SYS_SPI_ST_ENABLE_WP_PIN
+ enable the W#/Vpp signal to disable writing to the status
+ register on ST MICRON flashes like the N25Q128.
+ The status register write enable/disable bit, combined with
+ the W#/VPP signal provides hardware data protection for the
+ device as follows: When the enable/disable bit is set to 1,
+ and the W#/VPP signal is driven LOW, the status register
+ nonvolatile bits become read-only and the WRITE STATUS REGISTER
+ operation will not execute. The only way to exit this
+ hardware-protected mode is to drive W#/VPP HIGH.
+
- SystemACE Support:
CONFIG_SYSTEMACE
CONFIG_RSA
This enables the RSA algorithm used for FIT image verification
- in U-Boot. See doc/uImage/signature for more information.
+ in U-Boot. See doc/uImage.FIT/signature.txt for more information.
The signing part is build into mkimage regardless of this
option.
+- bootcount support:
+ CONFIG_BOOTCOUNT_LIMIT
+
+ This enables the bootcounter support, see:
+ http://www.denx.de/wiki/DULG/UBootBootCountLimit
+
+ CONFIG_AT91SAM9XE
+ enable special bootcounter support on at91sam9xe based boards.
+ CONFIG_BLACKFIN
+ enable special bootcounter support on blackfin based boards.
+ CONFIG_SOC_DA8XX
+ enable special bootcounter support on da850 based boards.
+ CONFIG_BOOTCOUNT_RAM
+ enable support for the bootcounter in RAM
+ CONFIG_BOOTCOUNT_I2C
+ enable support for the bootcounter on an i2c (like RTC) device.
+ CONFIG_SYS_I2C_RTC_ADDR = i2c chip address
+ CONFIG_SYS_BOOTCOUNT_ADDR = i2c addr which is used for
+ the bootcounter.
+ CONFIG_BOOTCOUNT_ALEN = address len
- Show boot progress:
CONFIG_SHOW_BOOT_PROGRESS
-150 common/cmd_nand.c Incorrect FIT image format
151 common/cmd_nand.c FIT image format OK
+- legacy image format:
+ CONFIG_IMAGE_FORMAT_LEGACY
+ enables the legacy image format support in U-Boot.
+
+ Default:
+ enabled if CONFIG_FIT_SIGNATURE is not defined.
+
+ CONFIG_DISABLE_IMAGE_LEGACY
+ disable the legacy image format
+
+ This define is introduced, as the legacy image format is
+ enabled per default for backward compatibility.
+
- FIT image support:
CONFIG_FIT
Enable support for the FIT uImage format.
using a hash signed and verified using RSA. See
doc/uImage.FIT/signature.txt for more details.
+ WARNING: When relying on signed FIT images with required
+ signature check the legacy image format is default
+ disabled. If a board need legacy image format support
+ enable this through CONFIG_IMAGE_FORMAT_LEGACY
+
+ CONFIG_FIT_DISABLE_SHA256
+ Supporting SHA256 hashes has quite an impact on binary size.
+ For constrained systems sha256 hash support can be disabled
+ with this option.
+
- Standalone program support:
CONFIG_STANDALONE_LOAD_ADDR
Adds the MTD partitioning infrastructure from the Linux
kernel. Needed for UBI support.
+ CONFIG_MTD_NAND_VERIFY_WRITE
+ verify if the written data is correct reread.
+
- UBI support
CONFIG_CMD_UBI
Make the verbose messages from UBI stop printing. This leaves
warnings and errors enabled.
+
+ CONFIG_MTD_UBI_WL_THRESHOLD
+ This parameter defines the maximum difference between the highest
+ erase counter value and the lowest erase counter value of eraseblocks
+ of UBI devices. When this threshold is exceeded, UBI starts performing
+ wear leveling by means of moving data from eraseblock with low erase
+ counter to eraseblocks with high erase counter.
+
+ The default value should be OK for SLC NAND flashes, NOR flashes and
+ other flashes which have eraseblock life-cycle 100000 or more.
+ However, in case of MLC NAND flashes which typically have eraseblock
+ life-cycle less than 10000, the threshold should be lessened (e.g.,
+ to 128 or 256, although it does not have to be power of 2).
+
+ default: 4096
+
+ CONFIG_MTD_UBI_BEB_LIMIT
+ This option specifies the maximum bad physical eraseblocks UBI
+ expects on the MTD device (per 1024 eraseblocks). If the
+ underlying flash does not admit of bad eraseblocks (e.g. NOR
+ flash), this value is ignored.
+
+ NAND datasheets often specify the minimum and maximum NVM
+ (Number of Valid Blocks) for the flashes' endurance lifetime.
+ The maximum expected bad eraseblocks per 1024 eraseblocks
+ then can be calculated as "1024 * (1 - MinNVB / MaxNVB)",
+ which gives 20 for most NANDs (MaxNVB is basically the total
+ count of eraseblocks on the chip).
+
+ To put it differently, if this value is 20, UBI will try to
+ reserve about 1.9% of physical eraseblocks for bad blocks
+ handling. And that will be 1.9% of eraseblocks on the entire
+ NAND chip, not just the MTD partition UBI attaches. This means
+ that if you have, say, a NAND flash chip admits maximum 40 bad
+ eraseblocks, and it is split on two MTD partitions of the same
+ size, UBI will reserve 40 eraseblocks when attaching a
+ partition.
+
+ default: 20
+
+ CONFIG_MTD_UBI_FASTMAP
+ Fastmap is a mechanism which allows attaching an UBI device
+ in nearly constant time. Instead of scanning the whole MTD device it
+ only has to locate a checkpoint (called fastmap) on the device.
+ The on-flash fastmap contains all information needed to attach
+ the device. Using fastmap makes only sense on large devices where
+ attaching by scanning takes long. UBI will not automatically install
+ a fastmap on old images, but you can set the UBI parameter
+ CONFIG_MTD_UBI_FASTMAP_AUTOCONVERT to 1 if you want so. Please note
+ that fastmap-enabled images are still usable with UBI implementations
+ without fastmap support. On typical flash devices the whole fastmap
+ fits into one PEB. UBI will reserve PEBs to hold two fastmaps.
+
+ CONFIG_MTD_UBI_FASTMAP_AUTOCONVERT
+ Set this parameter to enable fastmap automatically on images
+ without a fastmap.
+ default: 0
+
- UBIFS support
CONFIG_CMD_UBIFS
supports MMC, NAND and YMODEM loading of U-Boot and NAND
NAND loading of the Linux Kernel.
+ CONFIG_SPL_OS_BOOT
+ Enable booting directly to an OS from SPL.
+ See also: doc/README.falcon
+
CONFIG_SPL_DISPLAY_PRINT
For ARM, enable an optional function to print more information
about the running system.
continuing (the hardware starts execution after just
loading the first page rather than the full 4K).
+ CONFIG_SPL_SKIP_RELOCATE
+ Avoid SPL relocation
+
CONFIG_SPL_NAND_BASE
Include nand_base.c in the SPL. Requires
CONFIG_SPL_NAND_DRIVERS.
Support for NAND boot using simple NAND drivers that
expose the cmd_ctrl() interface.
+ CONFIG_SPL_MTD_SUPPORT
+ Support for the MTD subsystem within SPL. Useful for
+ environment on NAND support within SPL.
+
CONFIG_SPL_MPC8XXX_INIT_DDR_SUPPORT
Set for the SPL on PPC mpc8xxx targets, support for
drivers/ddr/fsl/libddr.o in SPL binary.
Configuration Settings:
-----------------------
+- CONFIG_SYS_SUPPORT_64BIT_DATA: Defined automatically if compiled as 64-bit.
+ Optionally it can be defined to support 64-bit memory commands.
+
- CONFIG_SYS_LONGHELP: Defined when you want long help messages included;
undefine this when you're short of memory.
- CONFIG_SYS_MALLOC_LEN:
Size of DRAM reserved for malloc() use.
+- CONFIG_SYS_MALLOC_F_LEN
+ Size of the malloc() pool for use before relocation. If
+ this is defined, then a very simple malloc() implementation
+ will become available before relocation. The address is just
+ below the global data, and the stack is moved down to make
+ space.
+
+ This feature allocates regions with increasing addresses
+ within the region. calloc() is supported, but realloc()
+ is not available. free() is supported but does nothing.
+ The memory will be freed (or in fact just forgotton) when
+ U-Boot relocates itself.
+
+ Pre-relocation malloc() is only supported on sandbox
+ at present but is fairly easy to enable for other archs.
+
+ Pre-relocation malloc() is only supported on ARM at present
+ but is fairly easy to enable for other archs.
+
- CONFIG_SYS_BOOTM_LEN:
Normally compressed uImages are limited to an
uncompressed size of 8 MBytes. If this is not enough,
its config.mk file). If you find problems enabling this option on
your board please report the problem and send patches!
-- CONFIG_SYS_SYM_OFFSETS
- This is set by architectures that use offsets for link symbols
- instead of absolute values. So bss_start is obtained using an
- offset _bss_start_ofs from CONFIG_SYS_TEXT_BASE, rather than
- directly. You should not need to touch this setting.
-
- CONFIG_OMAP_PLATFORM_RESET_TIME_MAX_USEC (OMAP only)
This is set by OMAP boards for the max time that reset should
be asserted. See doc/README.omap-reset-time for details on how
environment area within the total memory of your DataFlash placed
at the specified address.
+- CONFIG_ENV_IS_IN_SPI_FLASH:
+
+ Define this if you have a SPI Flash memory device which you
+ want to use for the environment.
+
+ - CONFIG_ENV_OFFSET:
+ - CONFIG_ENV_SIZE:
+
+ These two #defines specify the offset and size of the
+ environment area within the SPI Flash. CONFIG_ENV_OFFSET must be
+ aligned to an erase sector boundary.
+
+ - CONFIG_ENV_SECT_SIZE:
+
+ Define the SPI flash's sector size.
+
+ - CONFIG_ENV_OFFSET_REDUND (optional):
+
+ This setting describes a second storage area of CONFIG_ENV_SIZE
+ size used to hold a redundant copy of the environment data, so
+ that there is a valid backup copy in case there is a power failure
+ during a "saveenv" operation. CONFIG_ENV_OFFSET_RENDUND must be
+ aligned to an erase sector boundary.
+
+ - CONFIG_ENV_SPI_BUS (optional):
+ - CONFIG_ENV_SPI_CS (optional):
+
+ Define the SPI bus and chip select. If not defined they will be 0.
+
+ - CONFIG_ENV_SPI_MAX_HZ (optional):
+
+ Define the SPI max work clock. If not defined then use 1MHz.
+
+ - CONFIG_ENV_SPI_MODE (optional):
+
+ Define the SPI work mode. If not defined then use SPI_MODE_3.
+
- CONFIG_ENV_IS_IN_REMOTE:
Define this if you have a remote memory space which you
You will probably want to define these to avoid a really noisy system
when storing the env in UBI.
+- CONFIG_ENV_IS_IN_FAT:
+ Define this if you want to use the FAT file system for the environment.
+
+ - FAT_ENV_INTERFACE:
+
+ Define this to a string that is the name of the block device.
+
+ - FAT_ENV_DEV_AND_PART:
+
+ Define this to a string to specify the partition of the device. It can
+ be as following:
+
+ "D:P", "D:0", "D", "D:" or "D:auto" (D, P are integers. And P >= 1)
+ - "D:P": device D partition P. Error occurs if device D has no
+ partition table.
+ - "D:0": device D.
+ - "D" or "D:": device D partition 1 if device D has partition
+ table, or the whole device D if has no partition
+ table.
+ - "D:auto": first partition in device D with bootable flag set.
+ If none, first valid paratition in device D. If no
+ partition table then means device D.
+
+ - FAT_ENV_FILE:
+
+ It's a string of the FAT file name. This file use to store the
+ envrionment.
+
+ - CONFIG_FAT_WRITE:
+ This should be defined. Otherwise it cannot save the envrionment file.
+
- CONFIG_ENV_IS_IN_MMC:
Define this if you have an MMC device which you want to use for the
later, once stdio is running and output goes to the LCD, if
present.
+- CONFIG_BOARD_SIZE_LIMIT:
+ Maximum size of the U-Boot image. When defined, the
+ build system checks that the actual size does not
+ exceed it.
+
Low Level (hardware related) configuration options:
---------------------------------------------------
- CONFIG_SPL_AM33XX_ENABLE_RTC32K_OSC:
Enables the RTC32K OSC on AM33xx based plattforms
+- CONFIG_SYS_NAND_NO_SUBPAGE_WRITE
+ Option to disable subpage write in NAND driver
+ driver that uses this:
+ drivers/mtd/nand/davinci_nand.c
+
Freescale QE/FMAN Firmware Support:
-----------------------------------
are used to identify the storage device (NOR flash, SPI, etc) and the address
within that device.
-- CONFIG_SYS_QE_FMAN_FW_ADDR
- The address in the storage device where the firmware is located. The
+- CONFIG_SYS_FMAN_FW_ADDR
+ The address in the storage device where the FMAN microcode is located. The
+ meaning of this address depends on which CONFIG_SYS_QE_FW_IN_xxx macro
+ is also specified.
+
+- CONFIG_SYS_QE_FW_ADDR
+ The address in the storage device where the QE microcode is located. The
meaning of this address depends on which CONFIG_SYS_QE_FW_IN_xxx macro
is also specified.
window->master inbound window->master LAW->the ucode address in
master's memory space.
+Freescale Layerscape Management Complex Firmware Support:
+---------------------------------------------------------
+The Freescale Layerscape Management Complex (MC) supports the loading of
+"firmware".
+This firmware often needs to be loaded during U-Boot booting, so macros
+are used to identify the storage device (NOR flash, SPI, etc) and the address
+within that device.
+
+- CONFIG_FSL_MC_ENET
+ Enable the MC driver for Layerscape SoCs.
+
+- CONFIG_SYS_LS_MC_FW_ADDR
+ The address in the storage device where the firmware is located. The
+ meaning of this address depends on which CONFIG_SYS_LS_MC_FW_IN_xxx macro
+ is also specified.
+
+- CONFIG_SYS_LS_MC_FW_LENGTH
+ The maximum possible size of the firmware. The firmware binary format
+ has a field that specifies the actual size of the firmware, but it
+ might not be possible to read any part of the firmware unless some
+ local storage is allocated to hold the entire firmware first.
+
+- CONFIG_SYS_LS_MC_FW_IN_NOR
+ Specifies that MC firmware is located in NOR flash, mapped as
+ normal addressable memory via the LBC. CONFIG_SYS_LS_MC_FW_ADDR is the
+ virtual address in NOR flash.
+
Building the Software:
======================
sources you must configure U-Boot for one specific board type. This
is done by typing:
- make NAME_config
+ make NAME_defconfig
-where "NAME_config" is the name of one of the existing configu-
+where "NAME_defconfig" is the name of one of the existing configu-
rations; see boards.cfg for supported names.
Note: for some board special configuration names may exist; check if
or with LCD support. You can select such additional "features"
when choosing the configuration, i. e.
- make TQM823L_config
+ make TQM823L_defconfig
- will configure for a plain TQM823L, i. e. no LCD support
- make TQM823L_LCD_config
+ make TQM823L_LCD_defconfig
- will configure for a TQM823L with U-Boot console on LCD
etc.
1. Add O= to the make command line invocations:
make O=/tmp/build distclean
- make O=/tmp/build NAME_config
+ make O=/tmp/build NAME_defconfig
make O=/tmp/build all
2. Set environment variable BUILD_DIR to point to the desired location:
export BUILD_DIR=/tmp/build
make distclean
- make NAME_config
+ make NAME_defconfig
make all
Note that the command line "O=" setting overrides the BUILD_DIR environment
your board
3. If you're porting U-Boot to a new CPU, then also create a new
directory to hold your CPU specific code. Add any files you need.
-4. Run "make <board>_config" with your new name.
+4. Run "make <board>_defconfig" with your new name.
5. Type "make", and you should get a working "u-boot.srec" file
to be installed on your target system.
6. Debug and solve any problems that might arise.
and make sure that your definition of IMAP_ADDR uses the same value
as your U-Boot configuration in CONFIG_SYS_IMMR.
+Note that U-Boot now has a driver model, a unified model for drivers.
+If you are adding a new driver, plumb it into driver model. If there
+is no uclass available, you are encouraged to create one. See
+doc/driver-model.
+
Configuring the Linux kernel:
-----------------------------
Example:
- make TQM850L_config
+ make TQM850L_defconfig
make oldconfig
make dep
make uImage