blackfin: fix build error on bct-brettl2 board

[karo-tx-uboot.git] / README

diff --git a/README b/README
index f5a719db9d3a43e0bf7e45a20e8362fc207cd770..119bbc994d22db4dc544f16544be622d55d5d2eb 100644 (file)
--- a/README
+++ b/README
@@ -690,6 +690,14 @@ The following options need to be configured:
                exists, unlike the similar options in the Linux kernel. Do not
                set these options unless they apply!
 
+               COUNTER_FREQUENCY
+               Generic timer clock source frequency.
+
+               COUNTER_FREQUENCY_REAL
+               Generic timer clock source frequency if the real clock is
+               different from COUNTER_FREQUENCY, and can only be determined
+               at run time.
+
                NOTE: The following can be machine specific errata. These
                do have ability to provide rudimentary version and machine
                specific checks, but expect no product checks.
@@ -940,6 +948,9 @@ The following options need to be configured:
                bytes are output before the console is initialised, the
                earlier bytes are discarded.
 
+               Note that when printing the buffer a copy is made on the
+               stack so CONFIG_PRE_CON_BUF_SZ must fit on the stack.
+
                'Sane' compilers will generate smaller code if
                CONFIG_PRE_CON_BUF_SZ is a power of 2
 
@@ -1865,12 +1876,6 @@ CBFS (Coreboot Filesystem) support
                boot.  See the documentation file README.video for a
                description of this variable.
 
-               CONFIG_VIDEO_VGA
-
-               Enable the VGA video / BIOS for x86. The alternative if you
-               are using coreboot is to use the coreboot frame buffer
-               driver.
-
 
 - Keyboard Support:
                CONFIG_KEYBOARD
@@ -2105,18 +2110,6 @@ CBFS (Coreboot Filesystem) support
                Some PHY like Intel LXT971A need extra delay after
                command issued before MII status register can be read
 
-- Ethernet address:
-               CONFIG_ETHADDR
-               CONFIG_ETH1ADDR
-               CONFIG_ETH2ADDR
-               CONFIG_ETH3ADDR
-               CONFIG_ETH4ADDR
-               CONFIG_ETH5ADDR
-
-               Define a default value for Ethernet address to use
-               for the respective Ethernet interface, in case this
-               is not determined automatically.
-
 - IP address:
                CONFIG_IPADDR
 
@@ -2871,8 +2864,8 @@ CBFS (Coreboot Filesystem) support
                completely disabled. Anybody can change or delete
                these parameters.
 
-               Alternatively, if you #define _both_ CONFIG_ETHADDR
-               _and_ CONFIG_OVERWRITE_ETHADDR_ONCE, a default
+               Alternatively, if you define _both_ an ethaddr in the
+               default env _and_ CONFIG_OVERWRITE_ETHADDR_ONCE, a default
                Ethernet address is installed in the environment,
                which can be changed exactly ONCE by the user. [The
                serial# is unaffected by this, i. e. it remains
@@ -3088,17 +3081,6 @@ CBFS (Coreboot Filesystem) support
                memories can be connected with a given cs line.
                Currently Xilinx Zynq qspi supports these type of connections.
 
-               CONFIG_SYS_SPI_ST_ENABLE_WP_PIN
-               enable the W#/Vpp signal to disable writing to the status
-               register on ST MICRON flashes like the N25Q128.
-               The status register write enable/disable bit, combined with
-               the W#/VPP signal provides hardware data protection for the
-               device as follows: When the enable/disable bit is set to 1,
-               and the W#/VPP signal is driven LOW, the status register
-               nonvolatile bits become read-only and the WRITE STATUS REGISTER
-               operation will not execute. The only way to exit this
-               hardware-protected mode is to drive W#/VPP HIGH.
-
 - SystemACE Support:
                CONFIG_SYSTEMACE
 
@@ -4160,6 +4142,10 @@ Configuration Settings:
                list, simply add an entry for the same variable name to the
                ".flags" variable.
 
+       If CONFIG_REGEX is defined, the variable_name above is evaluated as a
+       regular expression. This allows multiple variables to define the same
+       flags without explicitly listing them for each variable.
+
 - CONFIG_ENV_ACCESS_IGNORE_FORCE
        If defined, don't allow the -f switch to env set override variable
        access flags.
@@ -5482,7 +5468,7 @@ loaded to, and "Flash Location" gives the image's address in NOR
 flash or offset in NAND flash.
 
 *Note* - these variables don't have to be defined for all boards, some
-boards currenlty use other variables for these purposes, and some
+boards currently use other variables for these purposes, and some
 boards use these variables for other purposes.
 
 Image              File Name        RAM Address       Flash Location
@@ -5558,6 +5544,10 @@ override any association in the static list. You can define
 CONFIG_ENV_CALLBACK_LIST_DEFAULT to a list (string) to define the
 ".callbacks" environment variable in the default or embedded environment.
 
+If CONFIG_REGEX is defined, the variable_name above is evaluated as a
+regular expression. This allows multiple variables to be connected to
+the same callback without explicitly listing them all out.
+
 
 Command Line Parsing:
 =====================
@@ -5632,7 +5622,8 @@ o If both the SROM and the environment contain a MAC address, and the
   warning is printed.
 
 o If neither SROM nor the environment contain a MAC address, an error
-  is raised.
+  is raised. If CONFIG_NET_RANDOM_ETHADDR is defined, then in this case
+  a random, locally-assigned MAC is used.
 
 If Ethernet drivers implement the 'write_hwaddr' function, valid MAC addresses
 will be programmed into hardware as part of the initialization process.         This