/mpc5xx Files specific to Freescale MPC5xx CPUs
/mpc5xxx Files specific to Freescale MPC5xxx CPUs
/mpc8xx Files specific to Freescale MPC8xx CPUs
- /mpc8220 Files specific to Freescale MPC8220 CPUs
/mpc824x Files specific to Freescale MPC824x CPUs
/mpc8260 Files specific to Freescale MPC8260 CPUs
/mpc85xx Files specific to Freescale MPC85xx CPUs
CONFIG_CMD_SF * Read/write/erase SPI NOR flash
CONFIG_CMD_SHA1SUM print sha1 memory digest
(requires CONFIG_CMD_MEMORY)
+ CONFIG_CMD_SOFTSWITCH * Soft switch setting command for BF60x
CONFIG_CMD_SOURCE "source" command Support
CONFIG_CMD_SPI * SPI serial bus support
CONFIG_CMD_TFTPSRV * TFTP transfer in server mode
If this option is set, the driver enables cache flush.
- TPM Support:
- CONFIG_GENERIC_LPC_TPM
+ CONFIG_TPM
+ Support TPM devices.
+
+ CONFIG_TPM_TIS_I2C
+ Support for i2c bus TPM devices. Only one device
+ per system is supported at this time.
+
+ CONFIG_TPM_TIS_I2C_BUS_NUMBER
+ Define the the i2c bus number for the TPM device
+
+ CONFIG_TPM_TIS_I2C_SLAVE_ADDRESS
+ Define the TPM's address on the i2c bus
+
+ CONFIG_TPM_TIS_I2C_BURST_LIMITATION
+ Define the burst count bytes upper limit
+
+ CONFIG_TPM_TIS_LPC
Support for generic parallel port TPM devices. Only one device
per system is supported at this time.
Address, size and partition on the MMC to load U-Boot from
when the MMC is being used in raw mode.
+ CONFIG_SYS_MMCSD_RAW_MODE_KERNEL_SECTOR
+ Sector to load kernel uImage from when MMC is being
+ used in raw mode (for Falcon mode)
+
+ CONFIG_SYS_MMCSD_RAW_MODE_ARGS_SECTOR,
+ CONFIG_SYS_MMCSD_RAW_MODE_ARGS_SECTORS
+ Sector and number of sectors to load kernel argument
+ parameters from when MMC is being used in raw mode
+ (for falcon mode)
+
CONFIG_SPL_FAT_SUPPORT
Support for fs/fat/libfat.o in SPL binary
CONFIG_SPL_FAT_LOAD_PAYLOAD_NAME
Filename to read to load U-Boot when reading from FAT
+ CONFIG_SPL_FAT_LOAD_KERNEL_NAME
+ Filename to read to load kernel uImage when reading
+ from FAT (for Falcon mode)
+
+ CONFIG_SPL_FAT_LOAD_ARGS_NAME
+ Filename to read to load kernel argument parameters
+ when reading from FAT (for Falcon mode)
+
CONFIG_SPL_MPC83XX_WAIT_FOR_NAND
Set this for NAND SPL on PPC mpc83xx targets, so that
start.S waits for the rest of the SPL to load before
use an arch-specific makefile fragment instead, for
example if more than one image needs to be produced.
+ CONFIG_FIT_SPL_PRINT
+ Printing information about a FIT image adds quite a bit of
+ code to SPL. So this is normally disabled in SPL. Use this
+ option to re-enable it. This will affect the output of the
+ bootm command when booting a FIT image.
+
Modem Support:
--------------
You will probably want to define these to avoid a really noisy system
when storing the env in UBI.
+- CONFIG_ENV_IS_IN_MMC:
+
+ Define this if you have an MMC device which you want to use for the
+ environment.
+
+ - CONFIG_SYS_MMC_ENV_DEV:
+
+ Specifies which MMC device the environment is stored in.
+
+ - CONFIG_SYS_MMC_ENV_PART (optional):
+
+ Specifies which MMC partition the environment is stored in. If not
+ set, defaults to partition 0, the user area. Common values might be
+ 1 (first MMC boot partition), 2 (second MMC boot partition).
+
+ - CONFIG_ENV_OFFSET:
+ - CONFIG_ENV_SIZE:
+
+ These two #defines specify the offset and size of the environment
+ area within the specified MMC device.
+
+ If offset is positive (the usual case), it is treated as relative to
+ the start of the MMC partition. If offset is negative, it is treated
+ as relative to the end of the MMC partition. This can be useful if
+ your board may be fitted with different MMC devices, which have
+ different sizes for the MMC partitions, and you always want the
+ environment placed at the very end of the partition, to leave the
+ maximum possible space before it, to store other data.
+
+ These two values are in units of bytes, but must be aligned to an
+ MMC sector boundary.
+
+ - CONFIG_ENV_OFFSET_REDUND (optional):
+
+ Specifies a second storage area, of CONFIG_ENV_SIZE size, used to
+ hold a redundant copy of the environment data. This provides a
+ valid backup copy in case the other copy is corrupted, e.g. due
+ to a power failure during a "saveenv" operation.
+
+ This value may also be positive or negative; this is handled in the
+ same way as CONFIG_ENV_OFFSET.
+
+ This value is also in units of bytes, but must also be aligned to
+ an MMC sector boundary.
+
+ - CONFIG_ENV_SIZE_REDUND (optional):
+
+ This value need not be set, even when CONFIG_ENV_OFFSET_REDUND is
+ set. If this value is set, it must be set to the same value as
+ CONFIG_ENV_SIZE.
+
- CONFIG_SYS_SPI_INIT_OFFSET
Defines offset to the initial SPI buffer area in DPRAM. The
a second time. Useful for platforms that are pre-booted
by coreboot or similar.
+- CONFIG_PCI_INDIRECT_BRIDGE:
+ Enable support for indirect PCI bridges.
+
- CONFIG_SYS_SRIO:
Chip has SRIO or not
using the "bootz" command. The syntax of "bootz" command is the same
as the syntax of "bootm" command.
-Note, defining the CONFIG_SUPPORT_INITRD_RAW allows user to supply
+Note, defining the CONFIG_SUPPORT_RAW_INITRD allows user to supply
kernel with raw initrd images. The syntax is slightly different, the
address of the initrd must be augmented by it's size, in the following
format: "<initrd addres>:<initrd size>".