crash. This is needed for buggy hardware (uc101) where
no pull down resistor is connected to the signal IDE5V_DD7.
+ CONFIG_MACH_TYPE [relevant for ARM only][mandatory]
+
+ This setting is mandatory for all boards that have only one
+ machine type and must be used to specify the machine type
+ number as it appears in the ARM machine registry
+ (see http://www.arm.linux.org.uk/developer/machines/).
+ Only boards that have multiple machine types supported
+ in a single configuration file and the machine type is
+ runtime discoverable, do not have to use this setting.
+
- vxWorks boot parameters:
bootvx constructs a valid bootline using the following
Note: If a "bootargs" environment is defined, it will overwride
the defaults discussed just above.
+- Cache Configuration:
+ CONFIG_SYS_ICACHE_OFF - Do not enable instruction cache in U-Boot
+ CONFIG_SYS_DCACHE_OFF - Do not enable data cache in U-Boot
+ CONFIG_SYS_L2CACHE_OFF- Do not enable L2 cache in U-Boot
+
+- Cache Configuration for ARM:
+ CONFIG_SYS_L2_PL310 - Enable support for ARM PL310 L2 cache
+ controller
+ CONFIG_SYS_PL310_BASE - Physical base address of PL310
+ controller register space
+
- Serial Ports:
CONFIG_PL010_SERIAL
CONFIG_CMD_SPI * SPI serial bus support
CONFIG_CMD_TFTPSRV * TFTP transfer in server mode
CONFIG_CMD_USB * USB support
- CONFIG_CMD_VFD * VFD support (TRAB)
CONFIG_CMD_CDP * Cisco Discover Protocol support
CONFIG_CMD_FSL * Microblaze FSL support
enabled with CONFIG_CMD_MMC. The MMC driver also works with
the FAT fs. This is enabled with CONFIG_CMD_FAT.
+ CONFIG_SH_MMCIF
+ Support for Renesas on-chip MMCIF controller
+
+ CONFIG_SH_MMCIF_ADDR
+ Define the base address of MMCIF registers
+
+ CONFIG_SH_MMCIF_CLK
+ Define the clock frequency for MMCIF
+
- Journaling Flash filesystem support:
CONFIG_JFFS2_NAND, CONFIG_JFFS2_NAND_OFF, CONFIG_JFFS2_NAND_SIZE,
CONFIG_JFFS2_NAND_DEV
=>
If you now switch to the new I2C Bus 3 with "i2c dev 3"
- u-boot sends First the Commando to the mux@70 to enable
- channel 6, and then the Commando to the mux@71 to enable
+ u-boot first sends the command to the mux@70 to enable
+ channel 6, and then the command to the mux@71 to enable
the channel 4.
After that, you can use the "normal" i2c commands as
- usual, to communicate with your I2C devices behind
+ usual to communicate with your I2C devices behind
the 2 muxes.
This option is actually implemented for the bitbanging
Adds the MTD partitioning infrastructure from the Linux
kernel. Needed for UBI support.
+- SPL framework
+ CONFIG_SPL
+ Enable building of SPL globally.
+
+ CONFIG_SPL_TEXT_BASE
+ TEXT_BASE for linking the SPL binary.
+
+ CONFIG_SPL_LDSCRIPT
+ LDSCRIPT for linking the SPL binary.
+
+ CONFIG_SPL_LIBCOMMON_SUPPORT
+ Support for common/libcommon.o in SPL binary
+
+ CONFIG_SPL_LIBDISK_SUPPORT
+ Support for disk/libdisk.o in SPL binary
+
+ CONFIG_SPL_I2C_SUPPORT
+ Support for drivers/i2c/libi2c.o in SPL binary
+
+ CONFIG_SPL_GPIO_SUPPORT
+ Support for drivers/gpio/libgpio.o in SPL binary
+
+ CONFIG_SPL_MMC_SUPPORT
+ Support for drivers/mmc/libmmc.o in SPL binary
+
+ CONFIG_SPL_SERIAL_SUPPORT
+ Support for drivers/serial/libserial.o in SPL binary
+
+ CONFIG_SPL_SPI_FLASH_SUPPORT
+ Support for drivers/mtd/spi/libspi_flash.o in SPL binary
+
+ CONFIG_SPL_SPI_SUPPORT
+ Support for drivers/spi/libspi.o in SPL binary
+
+ CONFIG_SPL_FAT_SUPPORT
+ Support for fs/fat/libfat.o in SPL binary
+
+ CONFIG_SPL_LIBGENERIC_SUPPORT
+ Support for lib/libgeneric.o in SPL binary
Modem Support:
--------------
-[so far only for SMDK2400 and TRAB boards]
+[so far only for SMDK2400 boards]
- Modem support enable:
CONFIG_MODEM_SUPPORT
of environment data (variable area); in general, we support the
following configurations:
+- CONFIG_BUILD_ENVCRC:
+
+ Builds up envcrc with the target environment so that external utils
+ may easily extract it and embed it in final U-Boot images.
+
- CONFIG_ENV_IS_IN_FLASH:
Define this if the environment is in flash memory.
- CONFIG_SYS_SRIOn_MEM_SIZE:
Size of SRIO port 'n' memory region
+- CONFIG_SYS_NDFC_16
+ Defined to tell the NDFC that the NAND chip is using a
+ 16 bit bus.
+
+- CONFIG_SYS_NDFC_EBC0_CFG
+ Sets the EBC0_CFG register for the NDFC. If not defined
+ a default value will be used.
+
- CONFIG_SPD_EEPROM
Get DDR timing information from an I2C EEPROM. Common
with pluggable memory modules such as SODIMMs
one, specify here. Note that the value must resolve
to something your driver can deal with.
+- CONFIG_SYS_DDR_RAW_TIMING
+ Get DDR timing information from other than SPD. Common with
+ soldered DDR chips onboard without SPD. DDR raw timing
+ parameters are extracted from datasheet and hard-coded into
+ header files or board specific files.
+
- CONFIG_SYS_83XX_DDR_USES_CS0
Only for 83xx systems. If specified, then DDR should
be configured using CS0 and CS1 instead of CS2 and CS3.
other boot loader or by a debugger which performs
these initializations itself.
-- CONFIG_PRELOADER
+- CONFIG_SPL_BUILD
Modifies the behaviour of start.S when compiling a loader
that is executed before the actual U-Boot. E.g. when
compiling a NAND SPL.
This can be used to load and uncompress arbitrary
data.
+ fdt_high - if set this restricts the maximum address that the
+ flattened device tree will be copied into upon boot.
+ If this is set to the special value 0xFFFFFFFF then
+ the fdt will not be copied at all on boot. For this
+ to work it must reside in writable memory, have
+ sufficient padding on the end of it for u-boot to
+ add the information it needs into it, and the memory
+ must be accessible by the kernel.
+
i2cfast - (PPC405GP|PPC405EP only)
if set to 'y' configures Linux I2C driver for fast
mode (400kHZ). This environment variable is used in
All contributions to U-Boot should conform to the Linux kernel
coding style; see the file "Documentation/CodingStyle" and the script
-"scripts/Lindent" in your Linux kernel source directory. In sources
-originating from U-Boot a style corresponding to "Lindent -pcs" (adding
-spaces before parameters to function calls) is actually used.
+"scripts/Lindent" in your Linux kernel source directory.
Source files originating from a different project (for example the
MTD subsystem) are generally exempt from these guidelines and are not
Please also stick to the following formatting rules:
- remove any trailing white space
-- use TAB characters for indentation, not spaces
+- use TAB characters for indentation and vertical alignment, not spaces
- make sure NOT to use DOS '\r\n' line feeds
-- do not add more than 2 empty lines to source files
+- do not add more than 2 consecutive empty lines to source files
- do not add trailing empty lines to source files
Submissions which do not conform to the standards may be returned
* For major contributions, your entry to the CREDITS file
* When you add support for a new board, don't forget to add this
- board to the MAKEALL script, too.
+ board to the MAINTAINERS file, too.
* If your patch adds new configuration options, don't forget to
document these in the README file.
* The patch itself. If you are using git (which is *strongly*
recommended) you can easily generate the patch using the
- "git-format-patch". If you then use "git-send-email" to send it to
+ "git format-patch". If you then use "git send-email" to send it to
the U-Boot mailing list, you will avoid most of the common problems
with some other mail clients.
projects / karo-tx-uboot.git / blobdiff