API: Use stack pointer as API signature search hint in the glue layer.

[karo-tx-uboot.git] / README

diff --git a/README b/README
index 132650ee53e4b7f90e49cbd524bd93ab989c903c..b23a51258ed75bed57a114b71851b0d728f18547 100644 (file)
--- a/README
+++ b/README
@@ -484,6 +484,14 @@ The following options need to be configured:
                CONFIG_SYS_BAUDRATE_TABLE, see below.
                CONFIG_SYS_BRGCLK_PRESCALE, baudrate prescale
 
+- Console Rx buffer length
+               With CONFIG_SYS_SMC_RXBUFLEN it is possible to define
+               the maximum receive buffer length for the SMC.
+               This option is actual only for 82xx and 8xx possible.
+               If using CONFIG_SYS_SMC_RXBUFLEN also CONFIG_SYS_MAXIDLE
+               must be defined, to setup the maximum idle timeout for
+               the SMC.
+
 - Interrupt driven serial port input:
                CONFIG_SERIAL_SOFTWARE_FIFO
 
@@ -592,6 +600,10 @@ The following options need to be configured:
                CONFIG_CMD_DHCP         * DHCP support
                CONFIG_CMD_DIAG         * Diagnostics
                CONFIG_CMD_DOC          * Disk-On-Chip Support
+               CONFIG_CMD_DS4510       * ds4510 I2C gpio commands
+               CONFIG_CMD_DS4510_INFO  * ds4510 I2C info command
+               CONFIG_CMD_DS4510_MEM   * ds4510 I2C eeprom/sram commansd
+               CONFIG_CMD_DS4510_RST   * ds4510 I2C rst command
                CONFIG_CMD_DTT          * Digital Therm and Thermostat
                CONFIG_CMD_ECHO           echo arguments
                CONFIG_CMD_EEPROM       * EEPROM read/write support
@@ -1505,6 +1517,15 @@ The following options need to be configured:
                Bus on the MPC8260. But it should be not so difficult
                to add this option to other architectures.
 
+               CONFIG_SOFT_I2C_READ_REPEATED_START
+
+               defining this will force the i2c_read() function in
+               the soft_i2c driver to perform an I2C repeated start
+               between writing the address pointer and reading the
+               data.  If this define is omitted the default behaviour
+               of doing a stop-start sequence will be used.  Most I2C
+               devices can use either method, but some require one or
+               the other.
 
 - SPI Support: CONFIG_SPI
 
@@ -2032,6 +2053,9 @@ Configuration Settings:
 - CONFIG_SYS_LONGHELP: Defined when you want long help messages included;
                undefine this when you're short of memory.
 
+- CONFIG_SYS_HELP_CMD_WIDTH: Defined when you want to override the default
+               width of the commands listed in the 'help' command output.
+
 - CONFIG_SYS_PROMPT:   This is what U-Boot prints on the console to
                prompt for user input.
 
@@ -2579,6 +2603,10 @@ Low Level (hardware related) configuration options:
   CONFIG_SYS_POCMR2_MASK_ATTRIB: (MPC826x only)
                Overrides the default PCI memory map in cpu/mpc8260/pci.c if set.
 
+- CONFIG_PCI_DISABLE_PCIE:
+               Disable PCI-Express on systems where it is supported but not
+               required.
+
 - CONFIG_SPD_EEPROM
                Get DDR timing information from an I2C EEPROM. Common
                with pluggable memory modules such as SODIMMs
@@ -3005,8 +3033,7 @@ Some configuration options can be set using Environment Variables:
                  Useful on scripts which control the retry operation
                  themselves.
 
-  npe_ucode    - see CONFIG_IXP4XX_NPE_EXT_UCOD
-                 if set load address for the NPE microcode
+  npe_ucode    - set load address for the NPE microcode
 
   tftpsrcport  - If this is set, the value is used for TFTP's
                  UDP source port.