u32 gps_clk_cfg; /* 0xd0 */
u32 spi3_clk_cfg; /* 0xd4 */
u8 res5[0x28];
- u32 dram_clk_cfg; /* 0x100 */
+ u32 dram_clk_gate; /* 0x100 */
u32 be0_clk_cfg; /* 0x104 */
u32 be1_clk_cfg; /* 0x108 */
u32 fe0_clk_cfg; /* 0x10c */
#define PLL1_CFG_DEFAULT 0xa1005000
+#if defined CONFIG_OLD_SUNXI_KERNEL_COMPAT && defined CONFIG_MACH_SUN5I
+/*
+ * Older linux-sunxi-3.4 kernels override our PLL6 setting with 300 MHz,
+ * halving the mbus frequency, so set it to 300 MHz ourselves and base the
+ * mbus divider on that.
+ */
+#define PLL6_CFG_DEFAULT 0xa1009900
+#else
#define PLL6_CFG_DEFAULT 0xa1009911
+#endif
/* nand clock */
#define NAND_CLK_SRC_OSC24 0
#define AHB_GATE_OFFSET_USB_EHCI1 3
#define AHB_GATE_OFFSET_USB_OHCI0 2
#define AHB_GATE_OFFSET_USB_EHCI0 1
-#define AHB_GATE_OFFSET_USB 0
+#define AHB_GATE_OFFSET_USB0 0
/* ahb clock gate bit offset (second register) */
#define AHB_GATE_OFFSET_GMAC 17
+#define AHB_GATE_OFFSET_DE_FE0 14
+#define AHB_GATE_OFFSET_DE_BE0 12
+#define AHB_GATE_OFFSET_HDMI 11
+#define AHB_GATE_OFFSET_LCD1 5
+#define AHB_GATE_OFFSET_LCD0 4
+#define AHB_GATE_OFFSET_TVE1 3
+#define AHB_GATE_OFFSET_TVE0 2
#define CCM_AHB_GATE_GPS (0x1 << 26)
#define CCM_AHB_GATE_SDRAM (0x1 << 14)
#define CCM_AHB_GATE_DLL (0x1 << 15)
#define CCM_AHB_GATE_ACE (0x1 << 16)
+#define CCM_PLL3_CTRL_M(n) (((n) & 0x7f) << 0)
+#define CCM_PLL3_CTRL_INTEGER_MODE (0x1 << 15)
+#define CCM_PLL3_CTRL_EN (0x1 << 31)
+
#define CCM_PLL5_CTRL_M(n) (((n) & 0x3) << 0)
#define CCM_PLL5_CTRL_M_MASK CCM_PLL5_CTRL_M(0x3)
#define CCM_PLL5_CTRL_M_X(n) ((n) - 1)
#define CCM_MBUS_CTRL_CLK_SRC_PLL5 0x2
#define CCM_MBUS_CTRL_GATE (0x1 << 31)
-#define CCM_MMC_CTRL_OSCM24 (0x0 << 24)
-#define CCM_MMC_CTRL_PLL6 (0x1 << 24)
-#define CCM_MMC_CTRL_PLL5 (0x2 << 24)
+#define CCM_MMC_CTRL_M(x) ((x) - 1)
+#define CCM_MMC_CTRL_OCLK_DLY(x) ((x) << 8)
+#define CCM_MMC_CTRL_N(x) ((x) << 16)
+#define CCM_MMC_CTRL_SCLK_DLY(x) ((x) << 20)
+#define CCM_MMC_CTRL_OSCM24 (0x0 << 24)
+#define CCM_MMC_CTRL_PLL6 (0x1 << 24)
+#define CCM_MMC_CTRL_PLL5 (0x2 << 24)
+#define CCM_MMC_CTRL_ENABLE (0x1 << 31)
+
+#define CCM_DRAM_GATE_OFFSET_DE_FE1 24 /* Note the order of FE1 and */
+#define CCM_DRAM_GATE_OFFSET_DE_FE0 25 /* FE0 is swapped ! */
+#define CCM_DRAM_GATE_OFFSET_DE_BE0 26
+#define CCM_DRAM_GATE_OFFSET_DE_BE1 27
+
+#define CCM_LCD_CH0_CTRL_PLL3 (0 << 24)
+#define CCM_LCD_CH0_CTRL_PLL7 (1 << 24)
+#define CCM_LCD_CH0_CTRL_PLL3_2X (2 << 24)
+#define CCM_LCD_CH0_CTRL_PLL7_2X (3 << 24)
+#define CCM_LCD_CH0_CTRL_RST (0x1 << 30)
+#define CCM_LCD_CH0_CTRL_GATE (0x1 << 31)
-#define CCM_MMC_CTRL_ENABLE (0x1 << 31)
+#define CCM_LCD_CH1_CTRL_M(n) ((((n) - 1) & 0xf) << 0)
+/* We leave bit 11 set to 0, so sclk1 == sclk2 */
+#define CCM_LCD_CH1_CTRL_PLL3 (0 << 24)
+#define CCM_LCD_CH1_CTRL_PLL7 (1 << 24)
+#define CCM_LCD_CH1_CTRL_PLL3_2X (2 << 24)
+#define CCM_LCD_CH1_CTRL_PLL7_2X (3 << 24)
+/* Enable / disable both ch1 sclk1 and sclk2 at the same time */
+#define CCM_LCD_CH1_CTRL_GATE (0x1 << 31 | 0x1 << 15)
+
+#define CCM_LVDS_CTRL_RST (1 << 0)
+
+#define CCM_HDMI_CTRL_M(n) ((((n) - 1) & 0xf) << 0)
+#define CCM_HDMI_CTRL_PLL_MASK (3 << 24)
+#define CCM_HDMI_CTRL_PLL3 (0 << 24)
+#define CCM_HDMI_CTRL_PLL7 (1 << 24)
+#define CCM_HDMI_CTRL_PLL3_2X (2 << 24)
+#define CCM_HDMI_CTRL_PLL7_2X (3 << 24)
+/* No separate ddc gate on sun4i, sun5i and sun7i */
+#define CCM_HDMI_CTRL_DDC_GATE 0
+#define CCM_HDMI_CTRL_GATE (0x1 << 31)
#define CCM_GMAC_CTRL_TX_CLK_SRC_MII 0x0
#define CCM_GMAC_CTRL_TX_CLK_SRC_EXT_RGMII 0x1
#define CCM_GMAC_CTRL_TX_CLK_SRC_INT_RGMII 0x2
#define CCM_GMAC_CTRL_GPIT_MII (0x0 << 2)
#define CCM_GMAC_CTRL_GPIT_RGMII (0x1 << 2)
+#define CCM_GMAC_CTRL_RX_CLK_DELAY(x) ((x) << 5)
+#define CCM_GMAC_CTRL_TX_CLK_DELAY(x) ((x) << 10)
+#define CCM_USB_CTRL_PHY0_RST (0x1 << 0)
#define CCM_USB_CTRL_PHY1_RST (0x1 << 1)
#define CCM_USB_CTRL_PHY2_RST (0x1 << 2)
+#define CCM_USB_CTRL_OHCI0_CLK (0x1 << 6)
+#define CCM_USB_CTRL_OHCI1_CLK (0x1 << 7)
#define CCM_USB_CTRL_PHYGATE (0x1 << 8)
+/* These 3 are sun6i only, define them as 0 on sun4i */
+#define CCM_USB_CTRL_PHY0_CLK 0
+#define CCM_USB_CTRL_PHY1_CLK 0
+#define CCM_USB_CTRL_PHY2_CLK 0
+
+/* CCM bits common to all Display Engine (and IEP) clock ctrl regs */
+#define CCM_DE_CTRL_M(n) ((((n) - 1) & 0xf) << 0)
+#define CCM_DE_CTRL_PLL_MASK (3 << 24)
+#define CCM_DE_CTRL_PLL3 (0 << 24)
+#define CCM_DE_CTRL_PLL7 (1 << 24)
+#define CCM_DE_CTRL_PLL5P (2 << 24)
+#define CCM_DE_CTRL_RST (1 << 30)
+#define CCM_DE_CTRL_GATE (1 << 31)
+
+#ifndef __ASSEMBLY__
+void clock_set_pll1(unsigned int hz);
+void clock_set_pll3(unsigned int hz);
+unsigned int clock_get_pll5p(void);
+unsigned int clock_get_pll6(void);
+#endif
#endif /* _SUNXI_CLOCK_SUN4I_H */
projects / karo-tx-uboot.git / blobdiff