* Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
*/
+#include <linux/mfd/tmio.h>
+#include <linux/mmc/host.h>
+#include <linux/mtd/partitions.h>
#include <linux/pinctrl/machine.h>
#include <linux/platform_device.h>
+#include <linux/regulator/fixed.h>
+#include <linux/regulator/machine.h>
#include <linux/smsc911x.h>
+#include <linux/spi/spi.h>
+#include <linux/spi/flash.h>
#include <mach/common.h>
#include <mach/irqs.h>
#include <mach/r8a7778.h>
#include <asm/mach/arch.h>
+/*
+ * CN9(Upper side) SCIF/RCAN selection
+ *
+ * 1,4 3,6
+ * SW40 SCIF RCAN
+ * SW41 SCIF RCAN
+ */
+
+/*
+ * MMC (CN26) pin
+ *
+ * SW6 (D2) 3 pin
+ * SW7 (D5) ON
+ * SW8 (D3) 3 pin
+ * SW10 (D4) 1 pin
+ * SW12 (CLK) 1 pin
+ * SW13 (D6) 3 pin
+ * SW14 (CMD) ON
+ * SW15 (D6) 1 pin
+ * SW16 (D0) ON
+ * SW17 (D1) ON
+ * SW18 (D7) 3 pin
+ * SW19 (MMC) 1 pin
+ */
+
+/* Dummy supplies, where voltage doesn't matter */
+static struct regulator_consumer_supply dummy_supplies[] = {
+ REGULATOR_SUPPLY("vddvario", "smsc911x"),
+ REGULATOR_SUPPLY("vdd33a", "smsc911x"),
+};
+
static struct smsc911x_platform_config smsc911x_data = {
.irq_polarity = SMSC911X_IRQ_POLARITY_ACTIVE_LOW,
.irq_type = SMSC911X_IRQ_TYPE_PUSH_PULL,
DEFINE_RES_IRQ(irq_pin(0)), /* IRQ 0 */
};
+/* USB */
static struct rcar_phy_platform_data usb_phy_platform_data __initdata;
+/* SDHI */
+static struct sh_mobile_sdhi_info sdhi0_info = {
+ .tmio_caps = MMC_CAP_SD_HIGHSPEED,
+ .tmio_ocr_mask = MMC_VDD_165_195 | MMC_VDD_32_33 | MMC_VDD_33_34,
+ .tmio_flags = TMIO_MMC_HAS_IDLE_WAIT,
+};
+
+static struct sh_eth_plat_data ether_platform_data __initdata = {
+ .phy = 0x01,
+ .edmac_endian = EDMAC_LITTLE_ENDIAN,
+ .register_type = SH_ETH_REG_FAST_RCAR,
+ .phy_interface = PHY_INTERFACE_MODE_RMII,
+ /*
+ * Although the LINK signal is available on the board, it's connected to
+ * the link/activity LED output of the PHY, thus the link disappears and
+ * reappears after each packet. We'd be better off ignoring such signal
+ * and getting the link state from the PHY indirectly.
+ */
+ .no_ether_link = 1,
+};
+
+/* I2C */
+static struct i2c_board_info i2c0_devices[] = {
+ {
+ I2C_BOARD_INFO("rx8581", 0x51),
+ },
+};
+
+/* HSPI*/
+static struct mtd_partition m25p80_spi_flash_partitions[] = {
+ {
+ .name = "data(spi)",
+ .size = 0x0100000,
+ .offset = 0,
+ },
+};
+
+static struct flash_platform_data spi_flash_data = {
+ .name = "m25p80",
+ .type = "s25fl008k",
+ .parts = m25p80_spi_flash_partitions,
+ .nr_parts = ARRAY_SIZE(m25p80_spi_flash_partitions),
+};
+
+static struct spi_board_info spi_board_info[] __initdata = {
+ {
+ .modalias = "m25p80",
+ .max_speed_hz = 104000000,
+ .chip_select = 0,
+ .bus_num = 0,
+ .mode = SPI_MODE_0,
+ .platform_data = &spi_flash_data,
+ },
+};
+
+/* MMC */
+static struct sh_mmcif_plat_data sh_mmcif_plat = {
+ .sup_pclk = 0,
+ .ocr = MMC_VDD_165_195 | MMC_VDD_32_33 | MMC_VDD_33_34,
+ .caps = MMC_CAP_4_BIT_DATA |
+ MMC_CAP_8_BIT_DATA |
+ MMC_CAP_NEEDS_POLL,
+};
+
static const struct pinctrl_map bockw_pinctrl_map[] = {
+ /* Ether */
+ PIN_MAP_MUX_GROUP_DEFAULT("r8a777x-ether", "pfc-r8a7778",
+ "ether_rmii", "ether"),
+ /* HSPI0 */
+ PIN_MAP_MUX_GROUP_DEFAULT("sh-hspi.0", "pfc-r8a7778",
+ "hspi0_a", "hspi0"),
+ /* MMC */
+ PIN_MAP_MUX_GROUP_DEFAULT("sh_mmcif", "pfc-r8a7778",
+ "mmc_data8", "mmc"),
+ PIN_MAP_MUX_GROUP_DEFAULT("sh_mmcif", "pfc-r8a7778",
+ "mmc_ctrl", "mmc"),
/* SCIF0 */
PIN_MAP_MUX_GROUP_DEFAULT("sh-sci.0", "pfc-r8a7778",
"scif0_data_a", "scif0"),
PIN_MAP_MUX_GROUP_DEFAULT("sh-sci.0", "pfc-r8a7778",
"scif0_ctrl", "scif0"),
+ /* USB */
PIN_MAP_MUX_GROUP_DEFAULT("ehci-platform", "pfc-r8a7778",
"usb0", "usb0"),
PIN_MAP_MUX_GROUP_DEFAULT("ehci-platform", "pfc-r8a7778",
"usb1", "usb1"),
+ /* SDHI0 */
+ PIN_MAP_MUX_GROUP_DEFAULT("sh_mobile_sdhi.0", "pfc-r8a7778",
+ "sdhi0", "sdhi0"),
};
+#define FPGA 0x18200000
#define IRQ0MR 0x30
+#define PFC 0xfffc0000
+#define PUPR4 0x110
static void __init bockw_init(void)
{
- void __iomem *fpga;
+ void __iomem *base;
r8a7778_clock_init();
r8a7778_init_irq_extpin(1);
r8a7778_add_standard_devices();
r8a7778_add_usb_phy_device(&usb_phy_platform_data);
+ r8a7778_add_ether_device(ðer_platform_data);
+ r8a7778_add_i2c_device(0);
+ r8a7778_add_hspi_device(0);
+ r8a7778_add_mmc_device(&sh_mmcif_plat);
+ i2c_register_board_info(0, i2c0_devices,
+ ARRAY_SIZE(i2c0_devices));
+ spi_register_board_info(spi_board_info,
+ ARRAY_SIZE(spi_board_info));
pinctrl_register_mappings(bockw_pinctrl_map,
ARRAY_SIZE(bockw_pinctrl_map));
r8a7778_pinmux_init();
- fpga = ioremap_nocache(0x18200000, SZ_1M);
- if (fpga) {
+ /* for SMSC */
+ base = ioremap_nocache(FPGA, SZ_1M);
+ if (base) {
/*
* CAUTION
*
* it should be cared in the future
* Now, it is assuming IRQ0 was used only from SMSC.
*/
- u16 val = ioread16(fpga + IRQ0MR);
+ u16 val = ioread16(base + IRQ0MR);
val &= ~(1 << 4); /* enable SMSC911x */
- iowrite16(val, fpga + IRQ0MR);
- iounmap(fpga);
+ iowrite16(val, base + IRQ0MR);
+ iounmap(base);
+
+ regulator_register_fixed(0, dummy_supplies,
+ ARRAY_SIZE(dummy_supplies));
platform_device_register_resndata(
&platform_bus, "smsc911x", -1,
smsc911x_resources, ARRAY_SIZE(smsc911x_resources),
&smsc911x_data, sizeof(smsc911x_data));
}
+
+ /* for SDHI */
+ base = ioremap_nocache(PFC, 0x200);
+ if (base) {
+ /*
+ * FIXME
+ *
+ * SDHI CD/WP pin needs pull-up
+ */
+ iowrite32(ioread32(base + PUPR4) | (3 << 26), base + PUPR4);
+ iounmap(base);
+
+ r8a7778_sdhi_init(0, &sdhi0_info);
+ }
}
static const char *bockw_boards_compat_dt[] __initdata = {
projects / karo-tx-linux.git / blobdiff