Merge branch 'master' of /home/stefan/git/u-boot/u-boot into next

[karo-tx-uboot.git] / board / atmel / at91sam9260ek / at91sam9260ek.c

diff --git a/board/atmel/at91sam9260ek/at91sam9260ek.c b/board/atmel/at91sam9260ek/at91sam9260ek.c
index ef4d486be57309dcb77ed168e59cf6a5b04cff41..06d8512cc99448cfca5981eb3381a5d7bcc373b9 100644 (file)
--- a/board/atmel/at91sam9260ek/at91sam9260ek.c
+++ b/board/atmel/at91sam9260ek/at91sam9260ek.c
@@ -80,8 +80,8 @@ static void at91sam9260ek_nand_hw_init(void)
 
        /* Configure SMC CS3 for NAND/SmartMedia */
        at91_sys_write(AT91_SMC_SETUP(3),
-                      AT91_SMC_NWESETUP_(0) | AT91_SMC_NCS_WRSETUP_(0) |
-                      AT91_SMC_NRDSETUP_(0) | AT91_SMC_NCS_RDSETUP_(0));
+                      AT91_SMC_NWESETUP_(1) | AT91_SMC_NCS_WRSETUP_(0) |
+                      AT91_SMC_NRDSETUP_(1) | AT91_SMC_NCS_RDSETUP_(0));
        at91_sys_write(AT91_SMC_PULSE(3),
                       AT91_SMC_NWEPULSE_(3) | AT91_SMC_NCS_WRPULSE_(3) |
                       AT91_SMC_NRDPULSE_(3) | AT91_SMC_NCS_RDPULSE_(3));
@@ -149,7 +149,7 @@ static void at91sam9260ek_macb_hw_init(void)
 
        /* Need to reset PHY -> 500ms reset */
        at91_sys_write(AT91_RSTC_MR, AT91_RSTC_KEY |
-                                    AT91_RSTC_ERSTL | (0x0D << 8) |
+                                    (AT91_RSTC_ERSTL & (0x0D << 8)) |
                                     AT91_RSTC_URSTEN);
 
        at91_sys_write(AT91_RSTC_CR, AT91_RSTC_KEY | AT91_RSTC_EXTRST);
@@ -159,7 +159,7 @@ static void at91sam9260ek_macb_hw_init(void)
 
        /* Restore NRST value */
        at91_sys_write(AT91_RSTC_MR, AT91_RSTC_KEY |
-                                    AT91_RSTC_ERSTL | (0x0 << 8) |
+                                    (AT91_RSTC_ERSTL & (0x0 << 8)) |
                                     AT91_RSTC_URSTEN);
 
        /* Re-enable pull-up */
@@ -188,8 +188,17 @@ static void at91sam9260ek_macb_hw_init(void)
        at91_set_B_periph(AT91_PIN_PA25, 0);    /* ERX2 */
        at91_set_B_periph(AT91_PIN_PA26, 0);    /* ERX3 */
        at91_set_B_periph(AT91_PIN_PA27, 0);    /* ERXCK */
+#if defined(CONFIG_AT91SAM9260EK)
+       /*
+        * use PA10, PA11 for ETX2, ETX3.
+        * PA23 and PA24 are for TWI EEPROM
+        */
+       at91_set_B_periph(AT91_PIN_PA10, 0);    /* ETX2 */
+       at91_set_B_periph(AT91_PIN_PA11, 0);    /* ETX3 */
+#else
        at91_set_B_periph(AT91_PIN_PA23, 0);    /* ETX2 */
        at91_set_B_periph(AT91_PIN_PA24, 0);    /* ETX3 */
+#endif
        at91_set_B_periph(AT91_PIN_PA22, 0);    /* ETXER */
 #endif