Drop support for GTH board

[karo-tx-uboot.git] / board / gth / ee_dev.h

diff --git a/board/gth/ee_dev.h b/board/gth/ee_dev.h
deleted file mode 100644 (file)
index 3004b46..0000000
--- a/board/gth/ee_dev.h
+++ /dev/null
@@ -1,85 +0,0 @@
-/* By Thomas.Lange@Corelatus.com 001025
-   $Revision: 1.6 $
-
-   Definitions for EEPROM/VOLT METER  DS2438
-   Copyright (C) 2000-2001 Corelatus AB */
-
-#ifndef INCeedevh
-#define INCeedevh
-
-#define E_DEBUG(fmt,args...) if( Debug ) printk(KERN_DEBUG"EE: " fmt, ##args)
-
-#define PORT_B_PAR ((volatile immap_t *)CONFIG_SYS_IMMR)->im_cpm.cp_pbpar
-#define PORT_B_ODR ((volatile immap_t *)CONFIG_SYS_IMMR)->im_cpm.cp_pbodr
-#define PORT_B_DIR ((volatile immap_t *)CONFIG_SYS_IMMR)->im_cpm.cp_pbdir
-#define PORT_B_DAT ((volatile immap_t *)CONFIG_SYS_IMMR)->im_cpm.cp_pbdat
-
-#define SET_PORT_B_INPUT(Mask)  PORT_B_DIR &= ~(Mask)
-#define SET_PORT_B_OUTPUT(Mask) PORT_B_DIR |= Mask
-
-#define WRITE_PORT_B(Mask,Value) { \
-                       if (Value) PORT_B_DAT |= Mask; \
-                       else PORT_B_DAT &= ~(Mask); \
-               }
-#define WRITE_PORT(Value) WRITE_PORT_B(PB_EEPROM,Value)
-
-#define READ_PORT (PORT_B_DAT&PB_EEPROM)
-
-/* 64 bytes chip */
-#define EE_CHIP_SIZE 64
-
-/* We use this resistor for measuring the current drain on 3.3V */
-#define CURRENT_RESISTOR 0.022
-
-/* microsecs
-   Pull line down at least this long for reset pulse */
-#define RESET_LOW_TIME    490
-
-/* Read presence pulse after we release reset pulse */
-#define PRESENCE_TIMEOUT  100
-#define PRESENCE_LOW_TIME 200
-
-#define WRITE_0_LOW 80
-#define WRITE_1_LOW 2
-#define TOTAL_WRITE_LOW 80
-
-#define READ_LOW        2
-#define READ_TIMEOUT   10
-#define TOTAL_READ_LOW 80
-
-/*** Rom function commands ***/
-#define READ_ROM   0x33
-#define MATCH_ROM  0x55
-#define SKIP_ROM   0xCC
-#define SEARCH_ROM 0xF0
-
-
-/*** Memory_command_function ***/
-#define WRITE_SCRATCHPAD 0x4E
-#define READ_SCRATCHPAD  0xBE
-#define COPY_SCRATCHPAD  0x48
-#define RECALL_MEMORY    0xB8
-#define CONVERT_TEMP     0x44
-#define CONVERT_VOLTAGE  0xB4
-
-/* Chip is divided in 8 pages, 8 bytes each */
-
-#define EE_PAGE_SIZE 8
-
-/* All chip data we want are in page 0 */
-
-/* Bytes in page 0 */
-#define EE_P0_STATUS   0
-#define EE_P0_TEMP_LSB 1
-#define EE_P0_TEMP_MSB 2
-#define EE_P0_VOLT_LSB 3
-#define EE_P0_VOLT_MSB 4
-#define EE_P0_CURRENT_LSB 5
-#define EE_P0_CURRENT_MSB 6
-
-
-/* 40 byte user data is located at page 3-7 */
-#define EE_USER_PAGE_0 3
-#define USER_PAGES 5
-
-#endif /* INCeedevh */