*/
#include <common.h>
-#include <asm/processor.h>
#include <ppc440.h>
+#include <asm/processor.h>
#include <asm/gpio.h>
+#include <asm/io.h>
DECLARE_GLOBAL_DATA_PTR;
extern flash_info_t flash_info[CFG_MAX_FLASH_BANKS]; /* info for FLASH chips */
-ulong flash_get_size (ulong base, int banknum);
+ulong flash_get_size(ulong base, int banknum);
+int misc_init_r_kbd(void);
int board_early_init_f(void)
{
u32 sdr0_pfc1, sdr0_pfc2;
u32 reg;
- /* PLB Write pipelining disabled. Denali Core workaround */
- mtdcr(plb0_acr, 0xDE000000);
- mtdcr(plb1_acr, 0xDE000000);
+ /* PLB Write pipelining disabled. Denali Core workaround */
+ mtdcr(plb0_acr, 0xDE000000);
+ mtdcr(plb1_acr, 0xDE000000);
/*--------------------------------------------------------------------
* Setup the interrupt controller polarities, triggers, etc.
mtdcr(uic0sr, 0xffffffff); /* clear all. if write with 1 then the status is cleared */
mtdcr(uic0er, 0x00000000); /* disable all */
mtdcr(uic0cr, 0x00000000); /* we have not critical interrupts at the moment */
- mtdcr(uic0pr, 0xfffff7ff); /* Adjustment of the polarity */
- mtdcr(uic0tr, 0x00000810); /* per ref-board manual */
+ mtdcr(uic0pr, 0xFFBFF1EF); /* Adjustment of the polarity */
+ mtdcr(uic0tr, 0x00000900); /* per ref-board manual */
mtdcr(uic0vr, 0x00000000); /* int31 highest, base=0x000 is within DDRAM */
mtdcr(uic0sr, 0xffffffff); /* clear all */
mtdcr(uic1sr, 0xffffffff); /* clear all */
mtdcr(uic1er, 0x00000000); /* disable all */
mtdcr(uic1cr, 0x00000000); /* all non-critical */
- mtdcr(uic1pr, 0xFFFFC7AD); /* Adjustment of the polarity */
- mtdcr(uic1tr, 0x0600384A); /* per ref-board manual */
+ mtdcr(uic1pr, 0xFFFFC6A5); /* Adjustment of the polarity */
+ mtdcr(uic1tr, 0x60000040); /* per ref-board manual */
mtdcr(uic1vr, 0x00000000); /* int31 highest, base=0x000 is within DDRAM */
mtdcr(uic1sr, 0xffffffff); /* clear all */
mtdcr(uic2er, 0x00000000); /* disable all */
mtdcr(uic2cr, 0x00000000); /* all non-critical */
mtdcr(uic2pr, 0x27C00000); /* Adjustment of the polarity */
- mtdcr(uic2tr, 0xDFC00000); /* per ref-board manual */
+ mtdcr(uic2tr, 0x3C000000); /* per ref-board manual */
mtdcr(uic2vr, 0x00000000); /* int31 highest, base=0x000 is within DDRAM */
- mtdcr(uic2sr, 0xffffffff); /* clear all. Why this??? */
+ mtdcr(uic2sr, 0xffffffff); /* clear all */
/* Trace Pins are disabled. SDR0_PFC0 Register */
mtsdr(SDR0_PFC0, 0x0);
mtsdr(SDR0_PFC4, 0x80000000);
/* PCI arbiter disabled */
- /* PCI Host Configuration disbaled */
+ /* PCI Host Configuration disbaled */
mfsdr(sdr_pci0, reg);
- reg = 0;
+ reg = 0;
mtsdr(sdr_pci0, 0x00000000 | reg);
gpio_write_bit(CFG_GPIO_FLASH_WP, 1);
(void)flash_protect(FLAG_PROTECT_SET,
-CFG_MONITOR_LEN,
0xffffffff,
- &flash_info[0]);
+ &flash_info[1]);
/* Env protection ON by default */
(void)flash_protect(FLAG_PROTECT_SET,
CFG_ENV_ADDR_REDUND,
CFG_ENV_ADDR_REDUND + 2*CFG_ENV_SECT_SIZE - 1,
- &flash_info[0]);
+ &flash_info[1]);
/*
* USB suff...
udelay(500);
gpio_write_bit(CFG_GPIO_LIME_RST, 1);
+ /* Lime memory clock adjusted to 100MHz */
+ out_be32((void *)CFG_LIME_SDRAM_CLOCK, CFG_LIME_CLOCK_100MHZ);
+ /* Wait untill time expired. Because of requirements in lime manual */
+ udelay(300);
+ /* Write lime controller memory parameters */
+ out_be32((void *)CFG_LIME_MMR, CFG_LIME_MMR_VALUE);
+
/*
* Reset PHY's
*/
gpio_write_bit(CFG_GPIO_PHY1_RST, 1);
/*
- * Reset USB hub
+ * Init display controller
*/
- gpio_write_bit(CFG_GPIO_HUB_RST, 0);
- udelay(100);
- gpio_write_bit(CFG_GPIO_HUB_RST, 1);
+ /* Setup dot clock (internal PLL, division rate 1/16) */
+ out_be32((void *)0xc1fd0100, 0x00000f00);
+
+ /* Lime L0 init (16 bpp, 640x480) */
+ out_be32((void *)0xc1fd0020, 0x801401df);
+ out_be32((void *)0xc1fd0024, 0x0);
+ out_be32((void *)0xc1fd0028, 0x0);
+ out_be32((void *)0xc1fd002c, 0x0);
+ out_be32((void *)0xc1fd0110, 0x0);
+ out_be32((void *)0xc1fd0114, 0x0);
+ out_be32((void *)0xc1fd0118, 0x01df0280);
+
+ /* Display timing init */
+ out_be32((void *)0xc1fd0004, 0x031f0000);
+ out_be32((void *)0xc1fd0008, 0x027f027f);
+ out_be32((void *)0xc1fd000c, 0x015f028f);
+ out_be32((void *)0xc1fd0010, 0x020c0000);
+ out_be32((void *)0xc1fd0014, 0x01df01ea);
+ out_be32((void *)0xc1fd0018, 0x0);
+ out_be32((void *)0xc1fd001c, 0x01e00280);
+
+#if 1
+ /*
+ * Clear framebuffer using Lime's drawing engine
+ * (draw blue rect. with white border around it)
+ */
+ /* Setup mode and fbbase, xres, fg, bg */
+ out_be32((void *)0xc1ff0420, 0x8300);
+ out_be32((void *)0xc1ff0440, 0x0000);
+ out_be32((void *)0xc1ff0444, 0x0280);
+ out_be32((void *)0xc1ff0480, 0x7fff);
+ out_be32((void *)0xc1ff0484, 0x0000);
+ /* Reset clipping rectangle */
+ out_be32((void *)0xc1ff0454, 0x0000);
+ out_be32((void *)0xc1ff0458, 0x0280);
+ out_be32((void *)0xc1ff045c, 0x0000);
+ out_be32((void *)0xc1ff0460, 0x01e0);
+ /* Draw white rect. */
+ out_be32((void *)0xc1ff04a0, 0x09410000);
+ out_be32((void *)0xc1ff04a0, 0x00000000);
+ out_be32((void *)0xc1ff04a0, 0x01e00280);
+ udelay(2000);
+ /* Draw blue rect. */
+ out_be32((void *)0xc1ff0480, 0x001f);
+ out_be32((void *)0xc1ff04a0, 0x09410000);
+ out_be32((void *)0xc1ff04a0, 0x00010001);
+ out_be32((void *)0xc1ff04a0, 0x01de027e);
+#endif
+ /* Display enable, L0 layer */
+ out_be32((void *)0xc1fd0100, 0x80010f00);
+
+ /* TFT-LCD enable - PWM duty, lamp on */
+ out_be32((void *)0xc4000024, 0x64);
+ out_be32((void *)0xc4000020, 0x701);
+
+ /*
+ * Init matrix keyboard
+ */
+ misc_init_r_kbd();
return 0;
}
* certain pre-initialization actions.
*
************************************************************************/
-#if defined(CONFIG_PCI) && defined(CFG_PCI_PRE_INIT)
+#if defined(CONFIG_PCI)
int pci_pre_init(struct pci_controller *hose)
{
unsigned long addr;
return 1;
}
-#endif /* defined(CONFIG_PCI) && defined(CFG_PCI_PRE_INIT) */
+#endif /* defined(CONFIG_PCI) */
/*************************************************************************
* pci_target_init
projects / karo-tx-uboot.git / blobdiff