#include <asm/arch/gpio.h>
#include <asm/arch/mmc.h>
#include <asm/arch/usb_phy.h>
+#ifndef CONFIG_ARM64
+#include <asm/armv7.h>
+#endif
#include <asm/gpio.h>
#include <asm/io.h>
#include <nand.h>
#include <net.h>
+#include <sy8106a.h>
#if defined CONFIG_VIDEO_LCD_PANEL_I2C && !(defined CONFIG_SPL_BUILD)
/* So that we can use pin names in Kconfig and sunxi_name_to_gpio() */
/* add board specific code here */
int board_init(void)
{
- int id_pfr1, ret;
+ __maybe_unused int id_pfr1, ret;
gd->bd->bi_boot_params = (PHYS_SDRAM_0 + 0x100);
+#ifndef CONFIG_ARM64
asm volatile("mrc p15, 0, %0, c0, c1, 1" : "=r"(id_pfr1));
debug("id_pfr1: 0x%08x\n", id_pfr1);
/* Generic Timer Extension available? */
- if ((id_pfr1 >> 16) & 0xf) {
+ if ((id_pfr1 >> CPUID_ARM_GENTIMER_SHIFT) & 0xf) {
+ uint32_t freq;
+
debug("Setting CNTFRQ\n");
- /* CNTFRQ == 24 MHz */
- asm volatile("mcr p15, 0, %0, c14, c0, 0" : : "r"(24000000));
+
+ /*
+ * CNTFRQ is a secure register, so we will crash if we try to
+ * write this from the non-secure world (read is OK, though).
+ * In case some bootcode has already set the correct value,
+ * we avoid the risk of writing to it.
+ */
+ asm volatile("mrc p15, 0, %0, c14, c0, 0" : "=r"(freq));
+ if (freq != CONFIG_TIMER_CLK_FREQ) {
+ debug("arch timer frequency is %d Hz, should be %d, fixing ...\n",
+ freq, CONFIG_TIMER_CLK_FREQ);
+#ifdef CONFIG_NON_SECURE
+ printf("arch timer frequency is wrong, but cannot adjust it\n");
+#else
+ asm volatile("mcr p15, 0, %0, c14, c0, 0"
+ : : "r"(CONFIG_TIMER_CLK_FREQ));
+#endif
+ }
}
+#endif /* !CONFIG_ARM64 */
ret = axp_gpio_init();
if (ret)
return ret;
+#ifdef CONFIG_SATAPWR
+ gpio_request(CONFIG_SATAPWR, "satapwr");
+ gpio_direction_output(CONFIG_SATAPWR, 1);
+#endif
+#ifdef CONFIG_MACPWR
+ gpio_request(CONFIG_MACPWR, "macpwr");
+ gpio_direction_output(CONFIG_MACPWR, 1);
+#endif
+
/* Uses dm gpio code so do this here and not in i2c_init_board() */
return soft_i2c_board_init();
}
sunxi_gpio_set_pull(SUNXI_GPC(24), SUNXI_GPIO_PULL_UP);
sunxi_gpio_set_drv(SUNXI_GPC(24), 2);
}
-#elif defined(CONFIG_MACH_SUN8I)
+#elif defined(CONFIG_MACH_SUN8I) || defined(CONFIG_MACH_SUN50I)
/* SDC2: PC5-PC6, PC8-PC16 */
for (pin = SUNXI_GPC(5); pin <= SUNXI_GPC(6); pin++) {
sunxi_gpio_set_cfgpin(pin, SUNXI_GPC_SDC2);
if (!sunxi_mmc_has_egon_boot_signature(mmc0) &&
sunxi_mmc_has_egon_boot_signature(mmc1)) {
/* Booting from emmc / mmc2, swap */
- mmc0->block_dev.dev = 1;
- mmc1->block_dev.dev = 0;
+ mmc0->block_dev.devnum = 1;
+ mmc1->block_dev.devnum = 0;
}
#endif
int power_failed = 0;
unsigned long ramsize;
+#ifdef CONFIG_SY8106A_POWER
+ power_failed = sy8106a_set_vout1(CONFIG_SY8106A_VOUT1_VOLT);
+#endif
+
#if defined CONFIG_AXP152_POWER || defined CONFIG_AXP209_POWER || \
- defined CONFIG_AXP221_POWER || defined CONFIG_AXP818_POWER
+ defined CONFIG_AXP221_POWER || defined CONFIG_AXP809_POWER || \
+ defined CONFIG_AXP818_POWER
power_failed = axp_init();
-#if defined CONFIG_AXP221_POWER || defined CONFIG_AXP818_POWER
+#if defined CONFIG_AXP221_POWER || defined CONFIG_AXP809_POWER || \
+ defined CONFIG_AXP818_POWER
power_failed |= axp_set_dcdc1(CONFIG_AXP_DCDC1_VOLT);
#endif
power_failed |= axp_set_dcdc2(CONFIG_AXP_DCDC2_VOLT);
#if !defined(CONFIG_AXP209_POWER) && !defined(CONFIG_AXP818_POWER)
power_failed |= axp_set_dcdc4(CONFIG_AXP_DCDC4_VOLT);
#endif
-#if defined CONFIG_AXP221_POWER || defined CONFIG_AXP818_POWER
+#if defined CONFIG_AXP221_POWER || defined CONFIG_AXP809_POWER || \
+ defined CONFIG_AXP818_POWER
power_failed |= axp_set_dcdc5(CONFIG_AXP_DCDC5_VOLT);
#endif
-#ifdef CONFIG_AXP221_POWER
+#if defined CONFIG_AXP221_POWER || defined CONFIG_AXP809_POWER || \
+ defined CONFIG_AXP818_POWER
power_failed |= axp_set_aldo1(CONFIG_AXP_ALDO1_VOLT);
#endif
-#ifndef CONFIG_AXP818_POWER
power_failed |= axp_set_aldo2(CONFIG_AXP_ALDO2_VOLT);
-#endif
-#if !defined(CONFIG_AXP152_POWER) && !defined(CONFIG_AXP818_POWER)
+#if !defined(CONFIG_AXP152_POWER)
power_failed |= axp_set_aldo3(CONFIG_AXP_ALDO3_VOLT);
#endif
#ifdef CONFIG_AXP209_POWER
power_failed |= axp_set_aldo4(CONFIG_AXP_ALDO4_VOLT);
#endif
-#ifdef CONFIG_AXP221_POWER
- power_failed |= axp_set_dldo1(CONFIG_AXP_DLDO1_VOLT);
- power_failed |= axp_set_dldo2(CONFIG_AXP_DLDO2_VOLT);
- power_failed |= axp_set_dldo3(CONFIG_AXP_DLDO3_VOLT);
- power_failed |= axp_set_dldo4(CONFIG_AXP_DLDO4_VOLT);
+#if defined(CONFIG_AXP221_POWER) || defined(CONFIG_AXP809_POWER) || \
+ defined(CONFIG_AXP818_POWER)
+ power_failed |= axp_set_dldo(1, CONFIG_AXP_DLDO1_VOLT);
+ power_failed |= axp_set_dldo(2, CONFIG_AXP_DLDO2_VOLT);
+#if !defined CONFIG_AXP809_POWER
+ power_failed |= axp_set_dldo(3, CONFIG_AXP_DLDO3_VOLT);
+ power_failed |= axp_set_dldo(4, CONFIG_AXP_DLDO4_VOLT);
+#endif
power_failed |= axp_set_eldo(1, CONFIG_AXP_ELDO1_VOLT);
power_failed |= axp_set_eldo(2, CONFIG_AXP_ELDO2_VOLT);
power_failed |= axp_set_eldo(3, CONFIG_AXP_ELDO3_VOLT);
#endif
+
+#ifdef CONFIG_AXP818_POWER
+ power_failed |= axp_set_fldo(1, CONFIG_AXP_FLDO1_VOLT);
+ power_failed |= axp_set_fldo(2, CONFIG_AXP_FLDO2_VOLT);
+ power_failed |= axp_set_fldo(3, CONFIG_AXP_FLDO3_VOLT);
+#endif
+
+#if defined CONFIG_AXP809_POWER || defined CONFIG_AXP818_POWER
+ power_failed |= axp_set_sw(IS_ENABLED(CONFIG_AXP_SW_ON));
+#endif
#endif
printf("DRAM:");
ramsize = sunxi_dram_init();
- printf(" %lu MiB\n", ramsize >> 20);
+ printf(" %d MiB\n", (int)(ramsize >> 20));
if (!ramsize)
hang();
#if !defined(CONFIG_SPL_BUILD)
#include <asm/arch/spl.h>
+#include <environment.h>
/*
* Check the SPL header for the "sunxi" variant. If found: parse values
*/
static void parse_spl_header(const uint32_t spl_addr)
{
- struct boot_file_head *spl = (void *)spl_addr;
- if (memcmp(spl->spl_signature, SPL_SIGNATURE, 3) == 0) {
- uint8_t spl_header_version = spl->spl_signature[3];
- if (spl_header_version == SPL_HEADER_VERSION) {
- if (spl->fel_script_address)
- setenv_hex("fel_scriptaddr",
- spl->fel_script_address);
- return;
- }
+ struct boot_file_head *spl = (void *)(ulong)spl_addr;
+ if (memcmp(spl->spl_signature, SPL_SIGNATURE, 3) != 0)
+ return; /* signature mismatch, no usable header */
+
+ uint8_t spl_header_version = spl->spl_signature[3];
+ if (spl_header_version != SPL_HEADER_VERSION) {
printf("sunxi SPL version mismatch: expected %u, got %u\n",
SPL_HEADER_VERSION, spl_header_version);
+ return;
+ }
+ if (!spl->fel_script_address)
+ return;
+
+ if (spl->fel_uEnv_length != 0) {
+ /*
+ * data is expected in uEnv.txt compatible format, so "env
+ * import -t" the string(s) at fel_script_address right away.
+ */
+ himport_r(&env_htab, (char *)spl->fel_script_address,
+ spl->fel_uEnv_length, '\n', H_NOCLEAR, 0, 0, NULL);
+ return;
}
+ /* otherwise assume .scr format (mkimage-type script) */
+ setenv_hex("fel_scriptaddr", spl->fel_script_address);
}
#endif
}
#endif
-#ifdef CONFIG_OF_BOARD_SETUP
int ft_board_setup(void *blob, bd_t *bd)
{
+ int __maybe_unused r;
+
#ifdef CONFIG_VIDEO_DT_SIMPLEFB
- return sunxi_simplefb_setup(blob);
+ r = sunxi_simplefb_setup(blob);
+ if (r)
+ return r;
#endif
+ return 0;
}
-#endif /* CONFIG_OF_BOARD_SETUP */
projects / karo-tx-uboot.git / blobdiff