mpc83xx: make dtb basename file references equal those of linux

[karo-tx-uboot.git] / doc / README.m5475evb

diff --git a/doc/README.m5475evb b/doc/README.m5475evb
index cec4fd0434ca04ccbf48f5a878659d4d7f920d3a..37d14387851404dc13993a0aa918b34c34968395 100644 (file)
--- a/doc/README.m5475evb
+++ b/doc/README.m5475evb
@@ -106,8 +106,8 @@ CFG_I2C_SLAVE               -- define for I2C slave address
 CFG_I2C_OFFSET         -- define for I2C base address offset
 CFG_IMMR               -- define for MBAR offset
 
-CONFIG_PCI              -- define for PCI support
-CONFIG_PCI_PNP          -- define for Plug n play support
+CONFIG_PCI             -- define for PCI support
+CONFIG_PCI_PNP         -- define for Plug n play support
 CONFIG_SKIPPCI_HOSTBRIDGE      -- SKIP PCI Host bridge
 CFG_PCI_MEM_BUS                -- PCI memory logical offset
 CFG_PCI_MEM_PHYS       -- PCI memory physical offset
@@ -143,7 +143,7 @@ CFG_SDRAM_BASE      -- defines the DRAM Base
 3. COMPILATION
 ==============
 3.1    To create U-Boot the gcc-4.x compiler set (ColdFire ELF or uclinux
-        version) from codesourcery.com was used. Download it from:
+       version) from codesourcery.com was used. Download it from:
        http://www.codesourcery.com/gnu_toolchains/coldfire/download.html
 
 3.2 Compilation
@@ -206,68 +206,68 @@ flashsize   = 0x01200000
 flashoffset = 0x00000000
 sramstart   = 0xF2000000
 sramsize    = 0x00001000
-mbar        = 0xF0000000
+mbar       = 0xF0000000
 busfreq     = 133.333 MHz
-pcifreq     =      0 MHz
+pcifreq     =     0 MHz
 ethaddr     = 00:E0:0C:BC:E5:60
 eth1addr    = 00:E0:0C:BC:E5:61
 ip_addr     = 192.162.1.2
 baudrate    = 115200 bps
 -> ?
-?       - alias for 'help'
+?      - alias for 'help'
 autoscr - run script from memory
-base    - print or set address offset
-bdinfo  - print Board Info structure
-boot    - boot default, i.e., run 'bootcmd'
-bootd   - boot default, i.e., run 'bootcmd'
+base   - print or set address offset
+bdinfo - print Board Info structure
+boot   - boot default, i.e., run 'bootcmd'
+bootd  - boot default, i.e., run 'bootcmd'
 bootelf - Boot from an ELF image in memory
-bootm   - boot application image from memory
+bootm  - boot application image from memory
 bootp  - boot image via network using BootP/TFTP protocol
-bootvx  - Boot vxWorks from an ELF image
-cmp     - memory compare
+bootvx - Boot vxWorks from an ELF image
+cmp    - memory compare
 coninfo - print console devices and information
-cp      - memory copy
-crc32   - checksum calculation
-dcache  - enable or disable data cache
-echo    - echo args to console
-erase   - erase FLASH memory
-flinfo  - print FLASH memory information
-go      - start application at address 'addr'
-help    - print online help
-icache  - enable or disable instruction cache
-icrc32  - checksum calculation
-iloop   - infinite loop on address range
-imd     - i2c memory display
-iminfo  - print header information for application image
-imls    - list all images found in flash
-imm     - i2c memory modify (auto-incrementing)
-imw     - memory write (fill)
-inm     - memory modify (constant address)
-iprobe  - probe to discover valid I2C chip addresses
+cp     - memory copy
+crc32  - checksum calculation
+dcache - enable or disable data cache
+echo   - echo args to console
+erase  - erase FLASH memory
+flinfo - print FLASH memory information
+go     - start application at address 'addr'
+help   - print online help
+icache - enable or disable instruction cache
+icrc32 - checksum calculation
+iloop  - infinite loop on address range
+imd    - i2c memory display
+iminfo - print header information for application image
+imls   - list all images found in flash
+imm    - i2c memory modify (auto-incrementing)
+imw    - memory write (fill)
+inm    - memory modify (constant address)
+iprobe - probe to discover valid I2C chip addresses
 itest  - return true/false on integer compare
-loadb   - load binary file over serial line (kermit mode)
-loads   - load S-Record file over serial line
-loady   - load binary file over serial line (ymodem mode)
-loop    - infinite loop on address range
-md      - memory display
-mii     - MII utility commands
-mm      - memory modify (auto-incrementing)
-mtest   - simple RAM test
-mw      - memory write (fill)
+loadb  - load binary file over serial line (kermit mode)
+loads  - load S-Record file over serial line
+loady  - load binary file over serial line (ymodem mode)
+loop   - infinite loop on address range
+md     - memory display
+mii    - MII utility commands
+mm     - memory modify (auto-incrementing)
+mtest  - simple RAM test
+mw     - memory write (fill)
 nfs    - boot image via network using NFS protocol
-nm      - memory modify (constant address)
-pci     - list and access PCI Configuration Space
+nm     - memory modify (constant address)
+pci    - list and access PCI Configuration Space
 ping   - send ICMP ECHO_REQUEST to network host
 printenv- print environment variables
 protect - enable or disable FLASH write protection
 rarpboot- boot image via network using RARP/TFTP protocol
-reset   - Perform RESET of the CPU
-run     - run commands in an environment variable
+reset  - Perform RESET of the CPU
+run    - run commands in an environment variable
 saveenv - save environment variables to persistent storage
-setenv  - set environment variables
-sleep   - delay execution for some time
+setenv - set environment variables
+sleep  - delay execution for some time
 tftpboot- boot image via network using TFTP protocol
-usb     - USB sub-system
+usb    - USB sub-system
 usbboot - boot from USB device
 version - print monitor version
 -> usb start