/*
- * Copyright 2006 Freescale Semiconductor, Inc.
+ * Copyright 2006,2009 Freescale Semiconductor, Inc.
*
* This program is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License
#include <common.h>
-#ifdef CONFIG_FSL_I2C
#ifdef CONFIG_HARD_I2C
#include <command.h>
#include <asm/io.h>
#include <asm/fsl_i2c.h> /* HW definitions */
-#define I2C_TIMEOUT (CFG_HZ / 4)
+/* The maximum number of microseconds we will wait until another master has
+ * released the bus. If not defined in the board header file, then use a
+ * generic value.
+ */
+#ifndef CONFIG_I2C_MBB_TIMEOUT
+#define CONFIG_I2C_MBB_TIMEOUT 100000
+#endif
+
+/* The maximum number of microseconds we will wait for a read or write
+ * operation to complete. If not defined in the board header file, then use a
+ * generic value.
+ */
+#ifndef CONFIG_I2C_TIMEOUT
+#define CONFIG_I2C_TIMEOUT 10000
+#endif
#define I2C_READ_BIT 1
#define I2C_WRITE_BIT 0
* runs from ROM, and we can't switch buses because we can't modify
* the global variables.
*/
-#ifdef CFG_SPD_BUS_NUM
-static unsigned int i2c_bus_num __attribute__ ((section ("data"))) = CFG_SPD_BUS_NUM;
-#else
-static unsigned int i2c_bus_num __attribute__ ((section ("data"))) = 0;
+#ifndef CONFIG_SYS_SPD_BUS_NUM
+#define CONFIG_SYS_SPD_BUS_NUM 0
+#endif
+static unsigned int i2c_bus_num __attribute__ ((section (".data"))) = CONFIG_SYS_SPD_BUS_NUM;
+#if defined(CONFIG_I2C_MUX)
+static unsigned int i2c_bus_num_mux __attribute__ ((section ("data"))) = 0;
#endif
-static unsigned int i2c_bus_speed[2] = {CFG_I2C_SPEED, CFG_I2C_SPEED};
+static unsigned int i2c_bus_speed[2] = {CONFIG_SYS_I2C_SPEED, CONFIG_SYS_I2C_SPEED};
static const struct fsl_i2c *i2c_dev[2] = {
- (struct fsl_i2c *) (CFG_IMMR + CFG_I2C_OFFSET),
-#ifdef CFG_I2C2_OFFSET
- (struct fsl_i2c *) (CFG_IMMR + CFG_I2C2_OFFSET)
+ (struct fsl_i2c *) (CONFIG_SYS_IMMR + CONFIG_SYS_I2C_OFFSET),
+#ifdef CONFIG_SYS_I2C2_OFFSET
+ (struct fsl_i2c *) (CONFIG_SYS_IMMR + CONFIG_SYS_I2C2_OFFSET)
#endif
};
* For this table, the values are based on a value of 1 for the DFSR
* register. See the application note AN2919 "Determining the I2C Frequency
* Divider Ratio for SCL"
+ *
+ * ColdFire I2C frequency dividers for FDR values are different from
+ * PowerPC. The protocol to use the I2C module is still the same.
+ * A different table is defined and are based on MCF5xxx user manual.
+ *
*/
static const struct {
unsigned short divider;
- u8 dfsr;
u8 fdr;
} fsl_i2c_speed_map[] = {
- {160, 1, 32}, {192, 1, 33}, {224, 1, 34}, {256, 1, 35},
- {288, 1, 0}, {320, 1, 1}, {352, 6, 1}, {384, 1, 2}, {416, 6, 2},
- {448, 1, 38}, {480, 1, 3}, {512, 1, 39}, {544, 11, 3}, {576, 1, 4},
- {608, 22, 3}, {640, 1, 5}, {672, 32, 3}, {704, 11, 5}, {736, 43, 3},
- {768, 1, 6}, {800, 54, 3}, {832, 11, 6}, {896, 1, 42}, {960, 1, 7},
- {1024, 1, 43}, {1088, 22, 7}, {1152, 1, 8}, {1216, 43, 7}, {1280, 1, 9},
- {1408, 22, 9}, {1536, 1, 10}, {1664, 22, 10}, {1792, 1, 46},
- {1920, 1, 11}, {2048, 1, 47}, {2176, 43, 11}, {2304, 1, 12},
- {2560, 1, 13}, {2816, 43, 13}, {3072, 1, 14}, {3328, 43, 14},
- {3584, 1, 50}, {3840, 1, 15}, {4096, 1, 51}, {4608, 1, 16},
- {5120, 1, 17}, {6144, 1, 18}, {7168, 1, 54}, {7680, 1, 19},
- {8192, 1, 55}, {9216, 1, 20}, {10240, 1, 21}, {12288, 1, 22},
- {14336, 1, 58}, {15360, 1, 23}, {16384, 1, 59}, {18432, 1, 24},
- {20480, 1, 25}, {24576, 1, 26}, {28672, 1, 62}, {30720, 1, 27},
- {32768, 1, 63}, {36864, 1, 28}, {40960, 1, 29}, {49152, 1, 30},
- {61440, 1, 31}, {-1, 1, 31}
+#ifdef __M68K__
+ {20, 32}, {22, 33}, {24, 34}, {26, 35},
+ {28, 0}, {28, 36}, {30, 1}, {32, 37},
+ {34, 2}, {36, 38}, {40, 3}, {40, 39},
+ {44, 4}, {48, 5}, {48, 40}, {56, 6},
+ {56, 41}, {64, 42}, {68, 7}, {72, 43},
+ {80, 8}, {80, 44}, {88, 9}, {96, 41},
+ {104, 10}, {112, 42}, {128, 11}, {128, 43},
+ {144, 12}, {160, 13}, {160, 48}, {192, 14},
+ {192, 49}, {224, 50}, {240, 15}, {256, 51},
+ {288, 16}, {320, 17}, {320, 52}, {384, 18},
+ {384, 53}, {448, 54}, {480, 19}, {512, 55},
+ {576, 20}, {640, 21}, {640, 56}, {768, 22},
+ {768, 57}, {960, 23}, {896, 58}, {1024, 59},
+ {1152, 24}, {1280, 25}, {1280, 60}, {1536, 26},
+ {1536, 61}, {1792, 62}, {1920, 27}, {2048, 63},
+ {2304, 28}, {2560, 29}, {3072, 30}, {3840, 31},
+ {-1, 31}
+#endif
};
/**
unsigned int i2c_clk, unsigned int speed)
{
unsigned short divider = min(i2c_clk / speed, (unsigned short) -1);
- unsigned int i;
/*
* We want to choose an FDR/DFSR that generates an I2C bus speed that
* want the first divider that is equal to or greater than the
* calculated divider.
*/
+#ifdef __PPC__
+ u8 dfsr, fdr = 0x31; /* Default if no FDR found */
+ /* a, b and dfsr matches identifiers A,B and C respectively in AN2919 */
+ unsigned short a, b, ga, gb;
+ unsigned long c_div, est_div;
+
+#ifdef CONFIG_FSL_I2C_CUSTOM_DFSR
+ dfsr = CONFIG_FSL_I2C_CUSTOM_DFSR;
+#else
+ /* Condition 1: dfsr <= 50/T */
+ dfsr = (5 * (i2c_clk / 1000)) / 100000;
+#endif
+#ifdef CONFIG_FSL_I2C_CUSTOM_FDR
+ fdr = CONFIG_FSL_I2C_CUSTOM_FDR;
+ speed = i2c_clk / divider; /* Fake something */
+#else
+ debug("Requested speed:%d, i2c_clk:%d\n", speed, i2c_clk);
+ if (!dfsr)
+ dfsr = 1;
+
+ est_div = ~0;
+ for (ga = 0x4, a = 10; a <= 30; ga++, a += 2) {
+ for (gb = 0; gb < 8; gb++) {
+ b = 16 << gb;
+ c_div = b * (a + ((3*dfsr)/b)*2);
+ if ((c_div > divider) && (c_div < est_div)) {
+ unsigned short bin_gb, bin_ga;
+
+ est_div = c_div;
+ bin_gb = gb << 2;
+ bin_ga = (ga & 0x3) | ((ga & 0x4) << 3);
+ fdr = bin_gb | bin_ga;
+ speed = i2c_clk / est_div;
+ debug("FDR:0x%.2x, div:%ld, ga:0x%x, gb:0x%x, "
+ "a:%d, b:%d, speed:%d\n",
+ fdr, est_div, ga, gb, a, b, speed);
+ /* Condition 2 not accounted for */
+ debug("Tr <= %d ns\n",
+ (b - 3 * dfsr) * 1000000 /
+ (i2c_clk / 1000));
+ }
+ }
+ if (a == 20)
+ a += 2;
+ if (a == 24)
+ a += 4;
+ }
+ debug("divider:%d, est_div:%ld, DFSR:%d\n", divider, est_div, dfsr);
+ debug("FDR:0x%.2x, speed:%d\n", fdr, speed);
+#endif
+ writeb(dfsr, &dev->dfsrr); /* set default filter */
+ writeb(fdr, &dev->fdr); /* set bus speed */
+#else
+ unsigned int i;
for (i = 0; i < ARRAY_SIZE(fsl_i2c_speed_map); i++)
if (fsl_i2c_speed_map[i].divider >= divider) {
- u8 fdr, dfsr;
- dfsr = fsl_i2c_speed_map[i].dfsr;
+ u8 fdr;
+
fdr = fsl_i2c_speed_map[i].fdr;
speed = i2c_clk / fsl_i2c_speed_map[i].divider;
writeb(fdr, &dev->fdr); /* set bus speed */
- writeb(dfsr, &dev->dfsrr); /* set default filter */
+
break;
}
-
+#endif
return speed;
}
struct fsl_i2c *dev;
unsigned int temp;
- dev = (struct fsl_i2c *) (CFG_IMMR + CFG_I2C_OFFSET);
+#ifdef CONFIG_SYS_I2C_INIT_BOARD
+ /* Call board specific i2c bus reset routine before accessing the
+ * environment, which might be in a chip on that bus. For details
+ * about this problem see doc/I2C_Edge_Conditions.
+ */
+ i2c_init_board();
+#endif
+ dev = (struct fsl_i2c *) (CONFIG_SYS_IMMR + CONFIG_SYS_I2C_OFFSET);
writeb(0, &dev->cr); /* stop I2C controller */
udelay(5); /* let it shutdown in peace */
writeb(0x0, &dev->sr); /* clear status register */
writeb(I2C_CR_MEN, &dev->cr); /* start I2C controller */
-#ifdef CFG_I2C2_OFFSET
- dev = (struct fsl_i2c *) (CFG_IMMR + CFG_I2C2_OFFSET);
+#ifdef CONFIG_SYS_I2C2_OFFSET
+ dev = (struct fsl_i2c *) (CONFIG_SYS_IMMR + CONFIG_SYS_I2C2_OFFSET);
writeb(0, &dev->cr); /* stop I2C controller */
udelay(5); /* let it shutdown in peace */
writeb(0x0, &dev->sr); /* clear status register */
writeb(I2C_CR_MEN, &dev->cr); /* start I2C controller */
#endif
+
+#ifdef CONFIG_SYS_I2C_BOARD_LATE_INIT
+ /* Call board specific i2c bus reset routine AFTER the bus has been
+ * initialized. Use either this callpoint or i2c_init_board;
+ * which is called before i2c_init operations.
+ * For details about this problem see doc/I2C_Edge_Conditions.
+ */
+ i2c_board_late_init();
+#endif
}
-static __inline__ int
+static int
i2c_wait4bus(void)
{
- ulong timeval = get_timer(0);
+ unsigned long long timeval = get_ticks();
+ const unsigned long long timeout = usec2ticks(CONFIG_I2C_MBB_TIMEOUT);
while (readb(&i2c_dev[i2c_bus_num]->sr) & I2C_SR_MBB) {
- if (get_timer(timeval) > I2C_TIMEOUT) {
+ if ((get_ticks() - timeval) > timeout)
return -1;
- }
}
return 0;
i2c_wait(int write)
{
u32 csr;
- ulong timeval = get_timer(0);
+ unsigned long long timeval = get_ticks();
+ const unsigned long long timeout = usec2ticks(CONFIG_I2C_TIMEOUT);
do {
csr = readb(&i2c_dev[i2c_bus_num]->sr);
if (!(csr & I2C_SR_MIF))
continue;
+ /* Read again to allow register to stabilise */
+ csr = readb(&i2c_dev[i2c_bus_num]->sr);
writeb(0x0, &i2c_dev[i2c_bus_num]->sr);
}
return 0;
- } while (get_timer (timeval) < I2C_TIMEOUT);
+ } while ((get_ticks() - timeval) < timeout);
debug("i2c_wait: timed out\n");
return -1;
{
int i;
- writeb(I2C_CR_MEN | I2C_CR_MSTA | I2C_CR_MTX,
- &i2c_dev[i2c_bus_num]->cr);
-
for (i = 0; i < length; i++) {
writeb(data[i], &i2c_dev[i2c_bus_num]->dr);
writeb(I2C_CR_MEN | I2C_CR_MSTA | I2C_CR_TXAK,
&i2c_dev[i2c_bus_num]->cr);
- /* Generate stop on last byte */
+ /* Do not generate stop on last byte */
if (i == length - 1)
- writeb(I2C_CR_MEN | I2C_CR_TXAK, &i2c_dev[i2c_bus_num]->cr);
+ writeb(I2C_CR_MEN | I2C_CR_MSTA | I2C_CR_MTX,
+ &i2c_dev[i2c_bus_num]->cr);
data[i] = readb(&i2c_dev[i2c_bus_num]->dr);
}
writeb(I2C_CR_MEN, &i2c_dev[i2c_bus_num]->cr);
+ if (i2c_wait4bus()) /* Wait until STOP */
+ debug("i2c_read: wait4bus timed out\n");
+
if (i == length)
return 0;
}
writeb(I2C_CR_MEN, &i2c_dev[i2c_bus_num]->cr);
+ if (i2c_wait4bus()) /* Wait until STOP */
+ debug("i2c_write: wait4bus timed out\n");
if (i == length)
return 0;
return i2c_read(chip, 0, 0, NULL, 0);
}
-uchar
-i2c_reg_read(uchar i2c_addr, uchar reg)
-{
- uchar buf[1];
-
- i2c_read(i2c_addr, reg, 1, buf, 1);
-
- return buf[0];
-}
-
-void
-i2c_reg_write(uchar i2c_addr, uchar reg, uchar val)
-{
- i2c_write(i2c_addr, reg, 1, &val, 1);
-}
-
int i2c_set_bus_num(unsigned int bus)
{
-#ifdef CFG_I2C2_OFFSET
+#if defined(CONFIG_I2C_MUX)
+ if (bus < CONFIG_SYS_MAX_I2C_BUS) {
+ i2c_bus_num = bus;
+ } else {
+ int ret;
+
+ ret = i2x_mux_select_mux(bus);
+ if (ret)
+ return ret;
+ i2c_bus_num = 0;
+ }
+ i2c_bus_num_mux = bus;
+#else
+#ifdef CONFIG_SYS_I2C2_OFFSET
if (bus > 1) {
#else
if (bus > 0) {
}
i2c_bus_num = bus;
-
+#endif
return 0;
}
unsigned int i2c_get_bus_num(void)
{
+#if defined(CONFIG_I2C_MUX)
+ return i2c_bus_num_mux;
+#else
return i2c_bus_num;
+#endif
}
unsigned int i2c_get_bus_speed(void)
}
#endif /* CONFIG_HARD_I2C */
-#endif /* CONFIG_FSL_I2C */
projects / karo-tx-uboot.git / blobdiff