static void sdhci_finish_command(struct sdhci_host *);
static int sdhci_execute_tuning(struct mmc_host *mmc, u32 opcode);
static void sdhci_tuning_timer(unsigned long data);
+static void sdhci_enable_preset_value(struct sdhci_host *host, bool enable);
#ifdef CONFIG_PM_RUNTIME
static int sdhci_runtime_pm_get(struct sdhci_host *host);
}
}
+static u16 sdhci_get_preset_value(struct sdhci_host *host)
+{
+ u16 ctrl, preset = 0;
+
+ ctrl = sdhci_readw(host, SDHCI_HOST_CONTROL2);
+
+ switch (ctrl & SDHCI_CTRL_UHS_MASK) {
+ case SDHCI_CTRL_UHS_SDR12:
+ preset = sdhci_readw(host, SDHCI_PRESET_FOR_SDR12);
+ break;
+ case SDHCI_CTRL_UHS_SDR25:
+ preset = sdhci_readw(host, SDHCI_PRESET_FOR_SDR25);
+ break;
+ case SDHCI_CTRL_UHS_SDR50:
+ preset = sdhci_readw(host, SDHCI_PRESET_FOR_SDR50);
+ break;
+ case SDHCI_CTRL_UHS_SDR104:
+ preset = sdhci_readw(host, SDHCI_PRESET_FOR_SDR104);
+ break;
+ case SDHCI_CTRL_UHS_DDR50:
+ preset = sdhci_readw(host, SDHCI_PRESET_FOR_DDR50);
+ break;
+ default:
+ pr_warn("%s: Invalid UHS-I mode selected\n",
+ mmc_hostname(host->mmc));
+ preset = sdhci_readw(host, SDHCI_PRESET_FOR_SDR12);
+ break;
+ }
+ return preset;
+}
+
static void sdhci_set_clock(struct sdhci_host *host, unsigned int clock)
{
int div = 0; /* Initialized for compiler warning */
goto out;
if (host->version >= SDHCI_SPEC_300) {
+ if (sdhci_readw(host, SDHCI_HOST_CONTROL2) &
+ SDHCI_CTRL_PRESET_VAL_ENABLE) {
+ u16 pre_val;
+
+ clk = sdhci_readw(host, SDHCI_CLOCK_CONTROL);
+ pre_val = sdhci_get_preset_value(host);
+ div = (pre_val & SDHCI_PRESET_SDCLK_FREQ_MASK)
+ >> SDHCI_PRESET_SDCLK_FREQ_SHIFT;
+ if (host->clk_mul &&
+ (pre_val & SDHCI_PRESET_CLKGEN_SEL_MASK)) {
+ clk = SDHCI_PROG_CLOCK_MODE;
+ real_div = div + 1;
+ clk_mul = host->clk_mul;
+ } else {
+ real_div = max_t(int, 1, div << 1);
+ }
+ goto clock_set;
+ }
+
/*
* Check if the Host Controller supports Programmable Clock
* Mode.
*/
if (host->clk_mul) {
- u16 ctrl;
-
+ for (div = 1; div <= 1024; div++) {
+ if ((host->max_clk * host->clk_mul / div)
+ <= clock)
+ break;
+ }
/*
- * We need to figure out whether the Host Driver needs
- * to select Programmable Clock Mode, or the value can
- * be set automatically by the Host Controller based on
- * the Preset Value registers.
+ * Set Programmable Clock Mode in the Clock
+ * Control register.
*/
- ctrl = sdhci_readw(host, SDHCI_HOST_CONTROL2);
- if (!(ctrl & SDHCI_CTRL_PRESET_VAL_ENABLE)) {
- for (div = 1; div <= 1024; div++) {
- if (((host->max_clk * host->clk_mul) /
- div) <= clock)
- break;
- }
- /*
- * Set Programmable Clock Mode in the Clock
- * Control register.
- */
- clk = SDHCI_PROG_CLOCK_MODE;
- real_div = div;
- clk_mul = host->clk_mul;
- div--;
- }
+ clk = SDHCI_PROG_CLOCK_MODE;
+ real_div = div;
+ clk_mul = host->clk_mul;
+ div--;
} else {
/* Version 3.00 divisors must be a multiple of 2. */
if (host->max_clk <= clock)
div >>= 1;
}
+clock_set:
if (real_div)
host->mmc->actual_clock = (host->max_clk * clk_mul) / real_div;
host->clock = clock;
}
+static inline void sdhci_update_clock(struct sdhci_host *host)
+{
+ unsigned int clock;
+
+ clock = host->clock;
+ host->clock = 0;
+ sdhci_set_clock(host, clock);
+}
+
static int sdhci_set_power(struct sdhci_host *host, unsigned short power)
{
u8 pwr = 0;
static void sdhci_request(struct mmc_host *mmc, struct mmc_request *mrq)
{
struct sdhci_host *host;
- bool present;
+ int present;
unsigned long flags;
u32 tuning_opcode;
host->mrq = mrq;
- /* If polling, assume that the card is always present. */
- if (host->quirks & SDHCI_QUIRK_BROKEN_CARD_DETECTION)
- present = true;
- else
- present = sdhci_readl(host, SDHCI_PRESENT_STATE) &
- SDHCI_CARD_PRESENT;
-
- /* If we're using a cd-gpio, testing the presence bit might fail. */
- if (!present) {
- int ret = mmc_gpio_get_cd(host->mmc);
- if (ret > 0)
- present = true;
+ /*
+ * Firstly check card presence from cd-gpio. The return could
+ * be one of the following possibilities:
+ * negative: cd-gpio is not available
+ * zero: cd-gpio is used, and card is removed
+ * one: cd-gpio is used, and card is present
+ */
+ present = mmc_gpio_get_cd(host->mmc);
+ if (present < 0) {
+ /* If polling, assume that the card is always present. */
+ if (host->quirks & SDHCI_QUIRK_BROKEN_CARD_DETECTION)
+ present = 1;
+ else
+ present = sdhci_readl(host, SDHCI_PRESENT_STATE) &
+ SDHCI_CARD_PRESENT;
}
if (!present || host->flags & SDHCI_DEVICE_DEAD) {
sdhci_reinit(host);
}
+ if (host->version >= SDHCI_SPEC_300 &&
+ (ios->power_mode == MMC_POWER_UP))
+ sdhci_enable_preset_value(host, false);
+
sdhci_set_clock(host, ios->clock);
if (ios->power_mode == MMC_POWER_OFF)
/*
* If your platform has 8-bit width support but is not a v3 controller,
* or if it requires special setup code, you should implement that in
- * platform_8bit_width().
+ * platform_bus_width().
*/
- if (host->ops->platform_8bit_width)
- host->ops->platform_8bit_width(host, ios->bus_width);
- else {
+ if (host->ops->platform_bus_width) {
+ host->ops->platform_bus_width(host, ios->bus_width);
+ } else {
ctrl = sdhci_readb(host, SDHCI_HOST_CONTROL);
if (ios->bus_width == MMC_BUS_WIDTH_8) {
ctrl &= ~SDHCI_CTRL_4BITBUS;
if (host->version >= SDHCI_SPEC_300) {
u16 clk, ctrl_2;
- unsigned int clock;
/* In case of UHS-I modes, set High Speed Enable */
if ((ios->timing == MMC_TIMING_MMC_HS200) ||
sdhci_writeb(host, ctrl, SDHCI_HOST_CONTROL);
/* Re-enable SD Clock */
- clock = host->clock;
- host->clock = 0;
- sdhci_set_clock(host, clock);
+ sdhci_update_clock(host);
}
sdhci_writew(host, ctrl_2, SDHCI_HOST_CONTROL2);
}
+ if (!(host->quirks2 & SDHCI_QUIRK2_PRESET_VALUE_BROKEN) &&
+ ((ios->timing == MMC_TIMING_UHS_SDR12) ||
+ (ios->timing == MMC_TIMING_UHS_SDR25) ||
+ (ios->timing == MMC_TIMING_UHS_SDR50) ||
+ (ios->timing == MMC_TIMING_UHS_SDR104) ||
+ (ios->timing == MMC_TIMING_UHS_DDR50))) {
+ u16 preset;
+
+ sdhci_enable_preset_value(host, true);
+ preset = sdhci_get_preset_value(host);
+ ios->drv_type = (preset & SDHCI_PRESET_DRV_MASK)
+ >> SDHCI_PRESET_DRV_SHIFT;
+ }
+
/* Re-enable SD Clock */
- clock = host->clock;
- host->clock = 0;
- sdhci_set_clock(host, clock);
+ sdhci_update_clock(host);
} else
sdhci_writeb(host, ctrl, SDHCI_HOST_CONTROL);
spin_unlock_irqrestore(&host->lock, flags);
}
-static int sdhci_do_3_3v_signal_voltage_switch(struct sdhci_host *host,
- u16 ctrl)
+static int sdhci_do_start_signal_voltage_switch(struct sdhci_host *host,
+ struct mmc_ios *ios)
{
+ u16 ctrl;
int ret;
- /* Set 1.8V Signal Enable in the Host Control2 register to 0 */
- ctrl &= ~SDHCI_CTRL_VDD_180;
- sdhci_writew(host, ctrl, SDHCI_HOST_CONTROL2);
-
- if (host->vqmmc) {
- ret = regulator_set_voltage(host->vqmmc, 3300000, 3300000);
- if (ret) {
- pr_warning("%s: Switching to 3.3V signalling voltage "
- " failed\n", mmc_hostname(host->mmc));
- return -EIO;
- }
- }
- /* Wait for 5ms */
- usleep_range(5000, 5500);
+ /*
+ * Signal Voltage Switching is only applicable for Host Controllers
+ * v3.00 and above.
+ */
+ if (host->version < SDHCI_SPEC_300)
+ return 0;
- /* 3.3V regulator output should be stable within 5 ms */
ctrl = sdhci_readw(host, SDHCI_HOST_CONTROL2);
- if (!(ctrl & SDHCI_CTRL_VDD_180))
- return 0;
- pr_warning("%s: 3.3V regulator output did not became stable\n",
- mmc_hostname(host->mmc));
+ switch (ios->signal_voltage) {
+ case MMC_SIGNAL_VOLTAGE_330:
+ /* Set 1.8V Signal Enable in the Host Control2 register to 0 */
+ ctrl &= ~SDHCI_CTRL_VDD_180;
+ sdhci_writew(host, ctrl, SDHCI_HOST_CONTROL2);
- return -EIO;
-}
+ if (host->vqmmc) {
+ ret = regulator_set_voltage(host->vqmmc, 2700000, 3600000);
+ if (ret) {
+ pr_warning("%s: Switching to 3.3V signalling voltage "
+ " failed\n", mmc_hostname(host->mmc));
+ return -EIO;
+ }
+ }
+ /* Wait for 5ms */
+ usleep_range(5000, 5500);
-static int sdhci_do_1_8v_signal_voltage_switch(struct sdhci_host *host,
- u16 ctrl)
-{
- u8 pwr;
- u16 clk;
- u32 present_state;
- int ret;
+ /* 3.3V regulator output should be stable within 5 ms */
+ ctrl = sdhci_readw(host, SDHCI_HOST_CONTROL2);
+ if (!(ctrl & SDHCI_CTRL_VDD_180))
+ return 0;
- /* Stop SDCLK */
- clk = sdhci_readw(host, SDHCI_CLOCK_CONTROL);
- clk &= ~SDHCI_CLOCK_CARD_EN;
- sdhci_writew(host, clk, SDHCI_CLOCK_CONTROL);
+ pr_warning("%s: 3.3V regulator output did not became stable\n",
+ mmc_hostname(host->mmc));
+
+ return -EAGAIN;
+ case MMC_SIGNAL_VOLTAGE_180:
+ if (host->vqmmc) {
+ ret = regulator_set_voltage(host->vqmmc,
+ 1700000, 1950000);
+ if (ret) {
+ pr_warning("%s: Switching to 1.8V signalling voltage "
+ " failed\n", mmc_hostname(host->mmc));
+ return -EIO;
+ }
+ }
- /* Check whether DAT[3:0] is 0000 */
- present_state = sdhci_readl(host, SDHCI_PRESENT_STATE);
- if (!((present_state & SDHCI_DATA_LVL_MASK) >>
- SDHCI_DATA_LVL_SHIFT)) {
/*
* Enable 1.8V Signal Enable in the Host Control2
* register
*/
- if (host->vqmmc)
- ret = regulator_set_voltage(host->vqmmc,
- 1800000, 1800000);
- else
- ret = 0;
+ ctrl |= SDHCI_CTRL_VDD_180;
+ sdhci_writew(host, ctrl, SDHCI_HOST_CONTROL2);
- if (!ret) {
- ctrl |= SDHCI_CTRL_VDD_180;
- sdhci_writew(host, ctrl, SDHCI_HOST_CONTROL2);
+ /* Wait for 5ms */
+ usleep_range(5000, 5500);
- /* Wait for 5ms */
- usleep_range(5000, 5500);
+ /* 1.8V regulator output should be stable within 5 ms */
+ ctrl = sdhci_readw(host, SDHCI_HOST_CONTROL2);
+ if (ctrl & SDHCI_CTRL_VDD_180)
+ return 0;
- ctrl = sdhci_readw(host, SDHCI_HOST_CONTROL2);
- if (ctrl & SDHCI_CTRL_VDD_180) {
- /* Provide SDCLK again and wait for 1ms */
- clk = sdhci_readw(host, SDHCI_CLOCK_CONTROL);
- clk |= SDHCI_CLOCK_CARD_EN;
- sdhci_writew(host, clk, SDHCI_CLOCK_CONTROL);
- usleep_range(1000, 1500);
+ pr_warning("%s: 1.8V regulator output did not became stable\n",
+ mmc_hostname(host->mmc));
- /*
- * If DAT[3:0] level is 1111b, then the card
- * was successfully switched to 1.8V signaling.
- */
- present_state = sdhci_readl(host,
- SDHCI_PRESENT_STATE);
- if ((present_state & SDHCI_DATA_LVL_MASK) ==
- SDHCI_DATA_LVL_MASK)
- return 0;
+ return -EAGAIN;
+ case MMC_SIGNAL_VOLTAGE_120:
+ if (host->vqmmc) {
+ ret = regulator_set_voltage(host->vqmmc, 1100000, 1300000);
+ if (ret) {
+ pr_warning("%s: Switching to 1.2V signalling voltage "
+ " failed\n", mmc_hostname(host->mmc));
+ return -EIO;
}
}
- }
-
- /*
- * If we are here, that means the switch to 1.8V signaling
- * failed. We power cycle the card, and retry initialization
- * sequence by setting S18R to 0.
- */
- pwr = sdhci_readb(host, SDHCI_POWER_CONTROL);
- pwr &= ~SDHCI_POWER_ON;
- sdhci_writeb(host, pwr, SDHCI_POWER_CONTROL);
- if (host->vmmc)
- regulator_disable(host->vmmc);
-
- /* Wait for 1ms as per the spec */
- usleep_range(1000, 1500);
- pwr |= SDHCI_POWER_ON;
- sdhci_writeb(host, pwr, SDHCI_POWER_CONTROL);
- if (host->vmmc)
- regulator_enable(host->vmmc);
-
- pr_warning("%s: Switching to 1.8V signalling voltage failed, "
- "retrying with S18R set to 0\n", mmc_hostname(host->mmc));
-
- return -EAGAIN;
-}
-
-static int sdhci_do_start_signal_voltage_switch(struct sdhci_host *host,
- struct mmc_ios *ios)
-{
- u16 ctrl;
-
- /*
- * Signal Voltage Switching is only applicable for Host Controllers
- * v3.00 and above.
- */
- if (host->version < SDHCI_SPEC_300)
return 0;
-
- /*
- * We first check whether the request is to set signalling voltage
- * to 3.3V. If so, we change the voltage to 3.3V and return quickly.
- */
- ctrl = sdhci_readw(host, SDHCI_HOST_CONTROL2);
- if (ios->signal_voltage == MMC_SIGNAL_VOLTAGE_330)
- return sdhci_do_3_3v_signal_voltage_switch(host, ctrl);
- else if (!(ctrl & SDHCI_CTRL_VDD_180) &&
- (ios->signal_voltage == MMC_SIGNAL_VOLTAGE_180))
- return sdhci_do_1_8v_signal_voltage_switch(host, ctrl);
- else
+ default:
/* No signal voltage switch required */
return 0;
+ }
}
static int sdhci_start_signal_voltage_switch(struct mmc_host *mmc,
return err;
}
+static int sdhci_card_busy(struct mmc_host *mmc)
+{
+ struct sdhci_host *host = mmc_priv(mmc);
+ u32 present_state;
+
+ sdhci_runtime_pm_get(host);
+ /* Check whether DAT[3:0] is 0000 */
+ present_state = sdhci_readl(host, SDHCI_PRESENT_STATE);
+ sdhci_runtime_pm_put(host);
+
+ return !(present_state & SDHCI_DATA_LVL_MASK);
+}
+
static int sdhci_execute_tuning(struct mmc_host *mmc, u32 opcode)
{
struct sdhci_host *host;
return err;
}
-static void sdhci_do_enable_preset_value(struct sdhci_host *host, bool enable)
+
+static void sdhci_enable_preset_value(struct sdhci_host *host, bool enable)
{
u16 ctrl;
- unsigned long flags;
/* Host Controller v3.00 defines preset value registers */
if (host->version < SDHCI_SPEC_300)
return;
- spin_lock_irqsave(&host->lock, flags);
-
ctrl = sdhci_readw(host, SDHCI_HOST_CONTROL2);
/*
sdhci_writew(host, ctrl, SDHCI_HOST_CONTROL2);
host->flags &= ~SDHCI_PV_ENABLED;
}
-
- spin_unlock_irqrestore(&host->lock, flags);
}
-static void sdhci_enable_preset_value(struct mmc_host *mmc, bool enable)
+static void sdhci_card_event(struct mmc_host *mmc)
{
struct sdhci_host *host = mmc_priv(mmc);
+ unsigned long flags;
- sdhci_runtime_pm_get(host);
- sdhci_do_enable_preset_value(host, enable);
- sdhci_runtime_pm_put(host);
+ spin_lock_irqsave(&host->lock, flags);
+
+ /* Check host->mrq first in case we are runtime suspended */
+ if (host->mrq &&
+ !(sdhci_readl(host, SDHCI_PRESENT_STATE) & SDHCI_CARD_PRESENT)) {
+ pr_err("%s: Card removed during transfer!\n",
+ mmc_hostname(host->mmc));
+ pr_err("%s: Resetting controller.\n",
+ mmc_hostname(host->mmc));
+
+ sdhci_reset(host, SDHCI_RESET_CMD);
+ sdhci_reset(host, SDHCI_RESET_DATA);
+
+ host->mrq->cmd->error = -ENOMEDIUM;
+ tasklet_schedule(&host->finish_tasklet);
+ }
+
+ spin_unlock_irqrestore(&host->lock, flags);
}
static const struct mmc_host_ops sdhci_ops = {
.enable_sdio_irq = sdhci_enable_sdio_irq,
.start_signal_voltage_switch = sdhci_start_signal_voltage_switch,
.execute_tuning = sdhci_execute_tuning,
- .enable_preset_value = sdhci_enable_preset_value,
+ .card_event = sdhci_card_event,
+ .card_busy = sdhci_card_busy,
};
/*****************************************************************************\
static void sdhci_tasklet_card(unsigned long param)
{
- struct sdhci_host *host;
- unsigned long flags;
-
- host = (struct sdhci_host*)param;
-
- spin_lock_irqsave(&host->lock, flags);
-
- /* Check host->mrq first in case we are runtime suspended */
- if (host->mrq &&
- !(sdhci_readl(host, SDHCI_PRESENT_STATE) & SDHCI_CARD_PRESENT)) {
- pr_err("%s: Card removed during transfer!\n",
- mmc_hostname(host->mmc));
- pr_err("%s: Resetting controller.\n",
- mmc_hostname(host->mmc));
+ struct sdhci_host *host = (struct sdhci_host*)param;
- sdhci_reset(host, SDHCI_RESET_CMD);
- sdhci_reset(host, SDHCI_RESET_DATA);
-
- host->mrq->cmd->error = -ENOMEDIUM;
- tasklet_schedule(&host->finish_tasklet);
- }
-
- spin_unlock_irqrestore(&host->lock, flags);
+ sdhci_card_event(host->mmc);
mmc_detect_change(host->mmc, msecs_to_jiffies(200));
}
(host->quirks & SDHCI_QUIRK_RESET_AFTER_REQUEST))) {
/* Some controllers need this kick or reset won't work here */
- if (host->quirks & SDHCI_QUIRK_CLOCK_BEFORE_RESET) {
- unsigned int clock;
-
+ if (host->quirks & SDHCI_QUIRK_CLOCK_BEFORE_RESET)
/* This is to force an update */
- clock = host->clock;
- host->clock = 0;
- sdhci_set_clock(host, clock);
- }
+ sdhci_update_clock(host);
/* Spec says we should do both at the same time, but Ricoh
controllers do not like that. */
pr_err("%s: ADMA error\n", mmc_hostname(host->mmc));
sdhci_show_adma_error(host);
host->data->error = -EIO;
+ if (host->ops->adma_workaround)
+ host->ops->adma_workaround(host, intmask);
}
if (host->data->error)
\*****************************************************************************/
#ifdef CONFIG_PM
+void sdhci_enable_irq_wakeups(struct sdhci_host *host)
+{
+ u8 val;
+ u8 mask = SDHCI_WAKE_ON_INSERT | SDHCI_WAKE_ON_REMOVE
+ | SDHCI_WAKE_ON_INT;
+
+ val = sdhci_readb(host, SDHCI_WAKE_UP_CONTROL);
+ val |= mask ;
+ /* Avoid fake wake up */
+ if (host->quirks & SDHCI_QUIRK_BROKEN_CARD_DETECTION)
+ val &= ~(SDHCI_WAKE_ON_INSERT | SDHCI_WAKE_ON_REMOVE);
+ sdhci_writeb(host, val, SDHCI_WAKE_UP_CONTROL);
+}
+EXPORT_SYMBOL_GPL(sdhci_enable_irq_wakeups);
+
+void sdhci_disable_irq_wakeups(struct sdhci_host *host)
+{
+ u8 val;
+ u8 mask = SDHCI_WAKE_ON_INSERT | SDHCI_WAKE_ON_REMOVE
+ | SDHCI_WAKE_ON_INT;
+
+ val = sdhci_readb(host, SDHCI_WAKE_UP_CONTROL);
+ val &= ~mask;
+ sdhci_writeb(host, val, SDHCI_WAKE_UP_CONTROL);
+}
+EXPORT_SYMBOL_GPL(sdhci_disable_irq_wakeups);
int sdhci_suspend_host(struct sdhci_host *host)
{
return ret;
}
- free_irq(host->irq, host);
-
+ if (!device_may_wakeup(mmc_dev(host->mmc))) {
+ sdhci_mask_irqs(host, SDHCI_INT_ALL_MASK);
+ free_irq(host->irq, host);
+ } else {
+ sdhci_enable_irq_wakeups(host);
+ enable_irq_wake(host->irq);
+ }
return ret;
}
host->ops->enable_dma(host);
}
- ret = request_irq(host->irq, sdhci_irq, IRQF_SHARED,
- mmc_hostname(host->mmc), host);
- if (ret)
- return ret;
+ if (!device_may_wakeup(mmc_dev(host->mmc))) {
+ ret = request_irq(host->irq, sdhci_irq, IRQF_SHARED,
+ mmc_hostname(host->mmc), host);
+ if (ret)
+ return ret;
+ } else {
+ sdhci_disable_irq_wakeups(host);
+ disable_irq_wake(host->irq);
+ }
if ((host->mmc->pm_flags & MMC_PM_KEEP_POWER) &&
(host->quirks2 & SDHCI_QUIRK2_HOST_OFF_CARD_ON)) {
}
EXPORT_SYMBOL_GPL(sdhci_resume_host);
-
-void sdhci_enable_irq_wakeups(struct sdhci_host *host)
-{
- u8 val;
- val = sdhci_readb(host, SDHCI_WAKE_UP_CONTROL);
- val |= SDHCI_WAKE_ON_INT;
- sdhci_writeb(host, val, SDHCI_WAKE_UP_CONTROL);
-}
-
-EXPORT_SYMBOL_GPL(sdhci_enable_irq_wakeups);
-
#endif /* CONFIG_PM */
#ifdef CONFIG_PM_RUNTIME
sdhci_do_set_ios(host, &host->mmc->ios);
sdhci_do_start_signal_voltage_switch(host, &host->mmc->ios);
- if (host_flags & SDHCI_PV_ENABLED)
- sdhci_do_enable_preset_value(host, true);
+ if ((host_flags & SDHCI_PV_ENABLED) &&
+ !(host->quirks2 & SDHCI_QUIRK2_PRESET_VALUE_BROKEN)) {
+ spin_lock_irqsave(&host->lock, flags);
+ sdhci_enable_preset_value(host, true);
+ spin_unlock_irqrestore(&host->lock, flags);
+ }
/* Set the re-tuning expiration flag */
if (host->flags & SDHCI_USING_RETUNING_TIMER)
mmc_hostname(mmc));
host->vqmmc = NULL;
}
- }
- else if (regulator_is_supported_voltage(host->vqmmc, 1800000, 1800000))
+ } else {
regulator_enable(host->vqmmc);
- else
+ if (!regulator_is_supported_voltage(host->vqmmc, 1700000,
+ 1950000))
+ caps[1] &= ~(SDHCI_SUPPORT_SDR104 |
+ SDHCI_SUPPORT_SDR50 |
+ SDHCI_SUPPORT_DDR50);
+ }
+
+ if (host->quirks2 & SDHCI_QUIRK2_NO_1_8_V)
caps[1] &= ~(SDHCI_SUPPORT_SDR104 | SDHCI_SUPPORT_SDR50 |
SDHCI_SUPPORT_DDR50);
mmc_hostname(mmc));
host->vmmc = NULL;
}
- } else
- regulator_enable(host->vmmc);
+ }
#ifdef CONFIG_REGULATOR
- if (host->vmmc) {
- ret = regulator_is_supported_voltage(host->vmmc, 3300000,
- 3300000);
+ /*
+ * Voltage range check makes sense only if regulator reports
+ * any voltage value.
+ */
+ if (host->vmmc && regulator_get_voltage(host->vmmc) > 0) {
+ ret = regulator_is_supported_voltage(host->vmmc, 2700000,
+ 3600000);
if ((ret <= 0) || (!(caps[0] & SDHCI_CAN_VDD_330)))
caps[0] &= ~SDHCI_CAN_VDD_330;
- ret = regulator_is_supported_voltage(host->vmmc, 3000000,
- 3000000);
if ((ret <= 0) || (!(caps[0] & SDHCI_CAN_VDD_300)))
caps[0] &= ~SDHCI_CAN_VDD_300;
- ret = regulator_is_supported_voltage(host->vmmc, 1800000,
- 1800000);
+ ret = regulator_is_supported_voltage(host->vmmc, 1700000,
+ 1950000);
if ((ret <= 0) || (!(caps[0] & SDHCI_CAN_VDD_180)))
caps[0] &= ~SDHCI_CAN_VDD_180;
}
#ifdef SDHCI_USE_LEDS_CLASS
reset:
sdhci_reset(host, SDHCI_RESET_ALL);
+ sdhci_mask_irqs(host, SDHCI_INT_ALL_MASK);
free_irq(host->irq, host);
#endif
untasklet:
if (!dead)
sdhci_reset(host, SDHCI_RESET_ALL);
+ sdhci_mask_irqs(host, SDHCI_INT_ALL_MASK);
free_irq(host->irq, host);
del_timer_sync(&host->timer);