+++ /dev/null
-#ifndef __ASM_SH_SMC37C93X_H
-#define __ASM_SH_SMC37C93X_H
-
-/*
- * linux/include/asm-sh/smc37c93x.h
- *
- * Copyright (C) 2000 Kazumoto Kojima
- *
- * SMSC 37C93x Super IO Chip support
- */
-
-/* Default base I/O address */
-#define FDC_PRIMARY_BASE 0x3f0
-#define IDE1_PRIMARY_BASE 0x1f0
-#define IDE1_SECONDARY_BASE 0x170
-#define PARPORT_PRIMARY_BASE 0x378
-#define COM1_PRIMARY_BASE 0x2f8
-#define COM2_PRIMARY_BASE 0x3f8
-#define RTC_PRIMARY_BASE 0x070
-#define KBC_PRIMARY_BASE 0x060
-#define AUXIO_PRIMARY_BASE 0x000 /* XXX */
-
-/* Logical device number */
-#define LDN_FDC 0
-#define LDN_IDE1 1
-#define LDN_IDE2 2
-#define LDN_PARPORT 3
-#define LDN_COM1 4
-#define LDN_COM2 5
-#define LDN_RTC 6
-#define LDN_KBC 7
-#define LDN_AUXIO 8
-
-/* Configuration port and key */
-#define CONFIG_PORT 0x3f0
-#define INDEX_PORT CONFIG_PORT
-#define DATA_PORT 0x3f1
-#define CONFIG_ENTER 0x55
-#define CONFIG_EXIT 0xaa
-
-/* Configuration index */
-#define CURRENT_LDN_INDEX 0x07
-#define POWER_CONTROL_INDEX 0x22
-#define ACTIVATE_INDEX 0x30
-#define IO_BASE_HI_INDEX 0x60
-#define IO_BASE_LO_INDEX 0x61
-#define IRQ_SELECT_INDEX 0x70
-#define DMA_SELECT_INDEX 0x74
-
-#define GPIO46_INDEX 0xc6
-#define GPIO47_INDEX 0xc7
-
-/* UART stuff. Only for debugging. */
-/* UART Register */
-
-#define UART_RBR 0x0 /* Receiver Buffer Register (Read Only) */
-#define UART_THR 0x0 /* Transmitter Holding Register (Write Only) */
-#define UART_IER 0x2 /* Interrupt Enable Register */
-#define UART_IIR 0x4 /* Interrupt Ident Register (Read Only) */
-#define UART_FCR 0x4 /* FIFO Control Register (Write Only) */
-#define UART_LCR 0x6 /* Line Control Register */
-#define UART_MCR 0x8 /* MODEM Control Register */
-#define UART_LSR 0xa /* Line Status Register */
-#define UART_MSR 0xc /* MODEM Status Register */
-#define UART_SCR 0xe /* Scratch Register */
-#define UART_DLL 0x0 /* Divisor Latch (LS) */
-#define UART_DLM 0x2 /* Divisor Latch (MS) */
-
-#ifndef __ASSEMBLY__
-typedef struct uart_reg {
- volatile __u16 rbr;
- volatile __u16 ier;
- volatile __u16 iir;
- volatile __u16 lcr;
- volatile __u16 mcr;
- volatile __u16 lsr;
- volatile __u16 msr;
- volatile __u16 scr;
-} uart_reg;
-#endif /* ! __ASSEMBLY__ */
-
-/* Alias for Write Only Register */
-
-#define thr rbr
-#define tcr iir
-
-/* Alias for Divisor Latch Register */
-
-#define dll rbr
-#define dlm ier
-#define fcr iir
-
-/* Interrupt Enable Register */
-
-#define IER_ERDAI 0x0100 /* Enable Received Data Available Interrupt */
-#define IER_ETHREI 0x0200 /* Enable Transmitter Holding Register Empty Interrupt */
-#define IER_ELSI 0x0400 /* Enable Receiver Line Status Interrupt */
-#define IER_EMSI 0x0800 /* Enable MODEM Status Interrupt */
-
-/* Interrupt Ident Register */
-
-#define IIR_IP 0x0100 /* "0" if Interrupt Pending */
-#define IIR_IIB0 0x0200 /* Interrupt ID Bit 0 */
-#define IIR_IIB1 0x0400 /* Interrupt ID Bit 1 */
-#define IIR_IIB2 0x0800 /* Interrupt ID Bit 2 */
-#define IIR_FIFO 0xc000 /* FIFOs enabled */
-
-/* FIFO Control Register */
-
-#define FCR_FEN 0x0100 /* FIFO enable */
-#define FCR_RFRES 0x0200 /* Receiver FIFO reset */
-#define FCR_TFRES 0x0400 /* Transmitter FIFO reset */
-#define FCR_DMA 0x0800 /* DMA mode select */
-#define FCR_RTL 0x4000 /* Receiver triger (LSB) */
-#define FCR_RTM 0x8000 /* Receiver triger (MSB) */
-
-/* Line Control Register */
-
-#define LCR_WLS0 0x0100 /* Word Length Select Bit 0 */
-#define LCR_WLS1 0x0200 /* Word Length Select Bit 1 */
-#define LCR_STB 0x0400 /* Number of Stop Bits */
-#define LCR_PEN 0x0800 /* Parity Enable */
-#define LCR_EPS 0x1000 /* Even Parity Select */
-#define LCR_SP 0x2000 /* Stick Parity */
-#define LCR_SB 0x4000 /* Set Break */
-#define LCR_DLAB 0x8000 /* Divisor Latch Access Bit */
-
-/* MODEM Control Register */
-
-#define MCR_DTR 0x0100 /* Data Terminal Ready */
-#define MCR_RTS 0x0200 /* Request to Send */
-#define MCR_OUT1 0x0400 /* Out 1 */
-#define MCR_IRQEN 0x0800 /* IRQ Enable */
-#define MCR_LOOP 0x1000 /* Loop */
-
-/* Line Status Register */
-
-#define LSR_DR 0x0100 /* Data Ready */
-#define LSR_OE 0x0200 /* Overrun Error */
-#define LSR_PE 0x0400 /* Parity Error */
-#define LSR_FE 0x0800 /* Framing Error */
-#define LSR_BI 0x1000 /* Break Interrupt */
-#define LSR_THRE 0x2000 /* Transmitter Holding Register Empty */
-#define LSR_TEMT 0x4000 /* Transmitter Empty */
-#define LSR_FIFOE 0x8000 /* Receiver FIFO error */
-
-/* MODEM Status Register */
-
-#define MSR_DCTS 0x0100 /* Delta Clear to Send */
-#define MSR_DDSR 0x0200 /* Delta Data Set Ready */
-#define MSR_TERI 0x0400 /* Trailing Edge Ring Indicator */
-#define MSR_DDCD 0x0800 /* Delta Data Carrier Detect */
-#define MSR_CTS 0x1000 /* Clear to Send */
-#define MSR_DSR 0x2000 /* Data Set Ready */
-#define MSR_RI 0x4000 /* Ring Indicator */
-#define MSR_DCD 0x8000 /* Data Carrier Detect */
-
-/* Baud Rate Divisor */
-
-#define UART_CLK (1843200) /* 1.8432 MHz */
-#define UART_BAUD(x) (UART_CLK / (16 * (x)))
-
-/* RTC register definition */
-#define RTC_SECONDS 0
-#define RTC_SECONDS_ALARM 1
-#define RTC_MINUTES 2
-#define RTC_MINUTES_ALARM 3
-#define RTC_HOURS 4
-#define RTC_HOURS_ALARM 5
-#define RTC_DAY_OF_WEEK 6
-#define RTC_DAY_OF_MONTH 7
-#define RTC_MONTH 8
-#define RTC_YEAR 9
-#define RTC_FREQ_SELECT 10
-# define RTC_UIP 0x80
-# define RTC_DIV_CTL 0x70
-/* This RTC can work under 32.768KHz clock only. */
-# define RTC_OSC_ENABLE 0x20
-# define RTC_OSC_DISABLE 0x00
-#define RTC_CONTROL 11
-# define RTC_SET 0x80
-# define RTC_PIE 0x40
-# define RTC_AIE 0x20
-# define RTC_UIE 0x10
-# define RTC_SQWE 0x08
-# define RTC_DM_BINARY 0x04
-# define RTC_24H 0x02
-# define RTC_DST_EN 0x01
-
-#endif /* __ASM_SH_SMC37C93X_H */
projects / karo-tx-linux.git / blobdiff