#define CONFIG_SPL_INIT_MINIMAL
#define CONFIG_SPL_SERIAL_SUPPORT
#define CONFIG_SPL_NAND_SUPPORT
-#define CONFIG_SPL_NAND_MINIMAL
+#define CONFIG_SPL_NAND_BOOT
#define CONFIG_SPL_FLUSH_IMAGE
#define CONFIG_SPL_TARGET "u-boot-with-spl.bin"
#define CONFIG_SYS_MEMTEST_END 0x01ffffff
/* DDR Setup */
-#define CONFIG_FSL_DDR3
+#define CONFIG_SYS_FSL_DDR3
#undef CONFIG_SYS_DDR_RAW_TIMING
#undef CONFIG_DDR_SPD
#define CONFIG_SYS_SPD_BUS_NUM 0
| CSOR_NAND_PB(64)) /*Pages Per Block = 64*/
/* NAND Flash Timing Params */
-#define CONFIG_SYS_NAND_FTIM0 (FTIM0_NAND_TCCST(0x08) \
- | FTIM0_NAND_TWP(0x06) \
- | FTIM0_NAND_TWCHT(0x03) \
+#define CONFIG_SYS_NAND_FTIM0 (FTIM0_NAND_TCCST(0x03) \
+ | FTIM0_NAND_TWP(0x05) \
+ | FTIM0_NAND_TWCHT(0x02) \
| FTIM0_NAND_TWH(0x04))
-#define CONFIG_SYS_NAND_FTIM1 (FTIM1_NAND_TADLE(0x18) \
- | FTIM1_NAND_TWBE(0x23) \
- | FTIM1_NAND_TRR(0x08) \
+#define CONFIG_SYS_NAND_FTIM1 (FTIM1_NAND_TADLE(0x1C) \
+ | FTIM1_NAND_TWBE(0x1E) \
+ | FTIM1_NAND_TRR(0x07) \
| FTIM1_NAND_TRP(0x05))
#define CONFIG_SYS_NAND_FTIM2 (FTIM2_NAND_TRAD(0x08) \
| FTIM2_NAND_TREH(0x04) \
- | FTIM2_NAND_TWHRE(0x3f))
-#define CONFIG_SYS_NAND_FTIM3 FTIM3_NAND_TWW(0x22)
+ | FTIM2_NAND_TWHRE(0x11))
+#define CONFIG_SYS_NAND_FTIM3 FTIM3_NAND_TWW(0x04)
#define CONFIG_SYS_NAND_BASE_LIST { CONFIG_SYS_NAND_BASE }
#define CONFIG_SYS_MAX_NAND_DEVICE 1
#define CONFIG_CMDLINE_EDITING /* Command-line editing */
#define CONFIG_AUTO_COMPLETE /* add autocompletion support */
#define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */
-#define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */
#if defined(CONFIG_CMD_KGDB)
#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
/* Print Buffer Size */
#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE/* Boot Argument Buffer Size */
-#define CONFIG_SYS_HZ 1000 /* decrementer freq: 1ms ticks */
/*
* For booting Linux, the board info and command line data
#if defined(CONFIG_CMD_KGDB)
#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */
-#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */
#endif
#define CONFIG_USB_EHCI