cm_t35: prevent splashimage from being set to a bad value

[karo-tx-uboot.git] / include / configs / JSE.h

diff --git a/include/configs/JSE.h b/include/configs/JSE.h
index 98f5661a09d285e773fe170b1bebe75b60ce2339..e0a0d8e46bd54a906df4af8e56f84cdfc680e755 100644 (file)
--- a/include/configs/JSE.h
+++ b/include/configs/JSE.h
@@ -37,7 +37,7 @@
   /* JSE has a PPC405GPr */
 #define CONFIG_405GP 1
   /* ... which is a 4xxx series */
-#define CONFIG_4xx   1
+#define CONFIG_4x   1
   /* ... with a 33MHz OSC. connected to the SysCLK input */
 #define CONFIG_SYS_CLK_FREQ    33333333
   /* ... with on-chip memory here (4KBytes) */
@@ -46,6 +46,8 @@
   /* Do not set up locked dcache as init ram. */
 #undef CONFIG_SYS_INIT_DCACHE_CS
 
+#define        CONFIG_SYS_TEXT_BASE    0xFFF80000
+
   /* Map the SystemACE chip (CS#1) here. (Must be a multiple of 1Meg) */
 #define CONFIG_SYSTEMACE 1
 #define CONFIG_SYS_SYSTEMACE_BASE 0xf0000000
@@ -57,10 +59,9 @@
   /* ... place INIT RAM in the OCM address */
 # define CONFIG_SYS_INIT_RAM_ADDR      CONFIG_SYS_OCM_DATA_ADDR
   /* ... give it the whole init ram */
-# define CONFIG_SYS_INIT_RAM_END       CONFIG_SYS_OCM_DATA_SIZE
+# define CONFIG_SYS_INIT_RAM_SIZE      CONFIG_SYS_OCM_DATA_SIZE
   /* ... Shave a bit off the end for global data */
-# define CONFIG_SYS_GBL_DATA_SIZE      128
-# define CONFIG_SYS_GBL_DATA_OFFSET    (CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE)
+# define CONFIG_SYS_GBL_DATA_OFFSET    (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
   /* ... and place the stack pointer at the top of what's left. */
 # define CONFIG_SYS_INIT_SP_OFFSET     CONFIG_SYS_GBL_DATA_OFFSET
 
@@ -95,18 +96,16 @@
 #define CONFIG_ENV_OFFSET      0x00
 #define CONFIG_ENV_SIZE        512
 
-
   /* The JSE connects UART1 to the console tap connector. */
-#define CONFIG_UART1_CONSOLE   1
+#define CONFIG_CONS_INDEX      2
+#define CONFIG_SYS_NS16550
+#define CONFIG_SYS_NS16550_SERIAL
+#define CONFIG_SYS_NS16550_REG_SIZE    1
+#define CONFIG_SYS_NS16550_CLK         get_serial_clock()
+
   /* Set console baudrate to 9600 */
 #define CONFIG_BAUDRATE                9600
 
-/* Size (bytes) of interrupt driven serial port buffer.
- * Set to 0 to use polling instead of interrupts.
- * Setting to 0 will also disable RTS/CTS handshaking.
- */
-#undef CONFIG_SERIAL_SOFTWARE_FIFO
-
 /*
  * Configuration related to auto-boot.
  *
@@ -135,7 +134,6 @@
 #define CONFIG_PPC4xx_EMAC
 #define CONFIG_MII             1       /* MII PHY management           */
 #define CONFIG_PHY_ADDR                1       /* PHY address                  */
-#define CONFIG_NET_MULTI
 
 
 /*
@@ -177,9 +175,6 @@
 #define CONFIG_SYS_PROMPT      "=> "           /* Monitor Command Prompt       */
 
 #define CONFIG_SYS_HUSH_PARSER                 /* use "hush" command parser    */
-#ifdef CONFIG_SYS_HUSH_PARSER
-#define CONFIG_SYS_PROMPT_HUSH_PS2     "> "
-#endif
 
 #if defined(CONFIG_CMD_KGDB)
 #define CONFIG_SYS_CBSIZE      1024            /* Console I/O Buffer Size      */
@@ -295,15 +290,6 @@
 /* Configuration Port location */
 #define CONFIG_PORT_ADDR       0xF0000500
 
-
-/*
- * Internal Definitions
- *
- * Boot Flags
- */
-#define BOOTFLAG_COLD  0x01            /* Normal Power-On: Boot from FLASH     */
-#define BOOTFLAG_WARM  0x02            /* Software reboot                      */
-
 #if defined(CONFIG_CMD_KGDB)
 #define CONFIG_KGDB_BAUDRATE   230400  /* speed to run kgdb serial port */
 #define CONFIG_KGDB_SER_INDEX  2       /* which serial port to use */