mxs: Make ehci-mxs multiport capable

[karo-tx-uboot.git] / include / configs / P1023RDS.h

diff --git a/include/configs/P1023RDS.h b/include/configs/P1023RDS.h
index 95f3a2c181443a0dc2924884edf14dfc670d70a3..878bd5fa5e6e9b7627be2466fefd8b1e560b491b 100644 (file)
--- a/include/configs/P1023RDS.h
+++ b/include/configs/P1023RDS.h
@@ -1,5 +1,5 @@
 /*
- * Copyright 2010-2011 Freescale Semiconductor, Inc.
+ * Copyright 2010-2012 Freescale Semiconductor, Inc.
  *
  * Authors:  Roy Zang <tie-fei.zang@freescale.com>
  *          Chunhe Lan <b25806@freescale.com>
@@ -99,15 +99,6 @@ extern unsigned long get_clock_freq(void);
 
 #define CONFIG_SYS_LBC_LBCR    0x00000000      /* Implement conversion of
                                                addresses in the LBC */
-/*
- * Base addresses -- Note these are effective addresses where the
- * actual resources get mapped (not physical addresses)
- */
-#define CONFIG_SYS_CCSRBAR_DEFAULT     0xff600000      /* CCSRBAR Default */
-#define CONFIG_SYS_CCSRBAR             0xff600000      /* relocated CCSRBAR */
-/* physical addr of CCSRBAR */
-#define CONFIG_SYS_CCSRBAR_PHYS        CONFIG_SYS_CCSRBAR
-#define CONFIG_SYS_IMMR        CONFIG_SYS_CCSRBAR      /* PQII uses CONFIG_SYS_IMMR */
 
 /* DDR Setup */
 #define CONFIG_VERY_BIG_RAM
@@ -308,9 +299,6 @@ extern unsigned long get_clock_freq(void);
 
 /* Use the HUSH parser */
 #define CONFIG_SYS_HUSH_PARSER
-#ifdef CONFIG_SYS_HUSH_PARSER
-#define CONFIG_SYS_PROMPT_HUSH_PS2 "> "
-#endif
 
 /*
  * Pass open firmware flat tree
@@ -319,9 +307,6 @@ extern unsigned long get_clock_freq(void);
 #define CONFIG_OF_BOARD_SETUP
 #define CONFIG_OF_STDOUT_VIA_ALIAS
 
-#define CONFIG_SYS_64BIT_VSPRINTF
-#define CONFIG_SYS_64BIT_STRTOUL
-
 /* new uImage format support */
 #define CONFIG_FIT
 #define CONFIG_FIT_VERBOSE     /* enable fit_format_{error,warning}() */
@@ -403,15 +388,10 @@ extern unsigned long get_clock_freq(void);
 
 #if defined(CONFIG_PCI)
 #define CONFIG_E1000           /* Defind e1000 pci Ethernet card */
-#define CONFIG_NET_MULTI
 #define CONFIG_PCI_PNP         /* do pci plug-and-play */
 #define CONFIG_PCI_SCAN_SHOW   /* show pci devices on startup */
 #endif /* CONFIG_PCI */
 
-#ifndef CONFIG_NET_MULTI
-#define CONFIG_NET_MULTI
-#endif
-
 /*
  * Environment
  */
@@ -461,6 +441,8 @@ extern unsigned long get_clock_freq(void);
 /*
  * USB
  */
+#define CONFIG_HAS_FSL_DR_USB
+#ifdef CONFIG_HAS_FSL_DR_USB
 #define CONFIG_USB_EHCI
 
 #ifdef CONFIG_USB_EHCI
@@ -473,6 +455,7 @@ extern unsigned long get_clock_freq(void);
 #define CONFIG_CMD_FAT
 #define CONFIG_DOS_PARTITION
 #endif
+#endif
 
 /*
  * Miscellaneous configurable options
@@ -509,7 +492,7 @@ extern unsigned long get_clock_freq(void);
 /*
  * Environment Configuration
  */
-#define CONFIG_BOOTFILE                uImage
+#define CONFIG_BOOTFILE                "uImage"
 #define CONFIG_UBOOTPATH       (u-boot.bin) /* U-Boot image on TFTP server */
 
 /* default location for tftp and bootm */
@@ -534,18 +517,20 @@ extern unsigned long get_clock_freq(void);
 
 #ifdef CONFIG_SYS_DPAA_FMAN
 #define CONFIG_FMAN_ENET
+#define CONFIG_PHY_MARVELL
 #endif
 
-#define CONFIG_SYS_FMAN_FW
 #ifndef CONFIG_NAND
 /* Default address of microcode for the Linux Fman driver */
 /* QE microcode/firmware address */
-#define CONFIG_SYS_FMAN_FW_ADDR                0xEF000000
+#define CONFIG_SYS_QE_FMAN_FW_IN_NOR
+#define CONFIG_SYS_QE_FMAN_FW_ADDR     0xEFF40000
 #else
-#define CONFIG_SYS_QE_FW_IN_NAND       0x1f00000
+#define CONFIG_SYS_QE_FMAN_FW_IN_NAND
+#define CONFIG_SYS_QE_FMAN_FW_ADDR     0x1f00000
 #endif
-#define CONFIG_SYS_FMAN_FW_LENGTH      0x10000
-#define CONFIG_SYS_FDT_PAD             (0x3000 + CONFIG_SYS_FMAN_FW_LENGTH)
+#define CONFIG_SYS_QE_FMAN_FW_LENGTH   0x10000
+#define CONFIG_SYS_FDT_PAD             (0x3000 + CONFIG_SYS_QE_FMAN_FW_LENGTH)
 
 #ifdef CONFIG_FMAN_ENET
 #define CONFIG_SYS_FM1_DTSEC1_PHY_ADDR 0x2