at91sam9260ek: move board id setup to config header

[karo-tx-uboot.git] / include / configs / PM828.h

diff --git a/include/configs/PM828.h b/include/configs/PM828.h
index 96c86f7e90130f9657bc08543e2a0088bf594c32..c37aafdd47a2c3e19126272965ce2deca8a72c09 100644 (file)
--- a/include/configs/PM828.h
+++ b/include/configs/PM828.h
@@ -39,6 +39,10 @@
 #define CONFIG_PM828           1       /* ...on a PM828 module */
 #define CONFIG_CPM2            1       /* Has a CPM2 */
 
+#ifndef CONFIG_SYS_TEXT_BASE
+#define CONFIG_SYS_TEXT_BASE   0x40000000      /* Standard: boot 64-bit flash */
+#endif
+
 #undef CONFIG_DB_CR826_J30x_ON         /* J30x jumpers on D.B. carrier */
 
 #define CONFIG_BOOTDELAY       5       /* autoboot after 5 seconds     */
@@ -96,16 +100,13 @@
  *
  * if CONFIG_ETHER_ON_SCC is selected, then
  *   - CONFIG_ETHER_INDEX must be set to the channel number (1-4)
- *   - CONFIG_NET_MULTI must not be defined
  *
  * if CONFIG_ETHER_ON_FCC is selected, then
  *   - one or more CONFIG_ETHER_ON_FCCx (x=1,2,3) must also be selected
- *   - CONFIG_NET_MULTI must be defined
  *
  * if CONFIG_ETHER_NONE is defined, then either the ethernet routines must be
  * defined elsewhere (as for the console), or CONFIG_CMD_NET must be unset.
  */
-#define CONFIG_NET_MULTI
 #undef CONFIG_ETHER_NONE               /* define if ether on something else */
 
 #undef CONFIG_ETHER_ON_SCC             /* define if ether on SCC       */
@@ -169,7 +170,6 @@
 #define CONFIG_CMD_BEDBUG
 #define CONFIG_CMD_DATE
 #define CONFIG_CMD_DHCP
-#define CONFIG_CMD_DOC
 #define CONFIG_CMD_EEPROM
 #define CONFIG_CMD_I2C
 #define CONFIG_CMD_NFS
@@ -179,18 +179,6 @@
 #define CONFIG_CMD_PCI
 #endif
 
-
-/*
- * Disk-On-Chip configuration
- */
-#define CONFIG_NAND_LEGACY
-
-#define CONFIG_SYS_DOC_SHORT_TIMEOUT
-#define CONFIG_SYS_MAX_DOC_DEVICE      1       /* Max number of DOC devices    */
-
-#define CONFIG_SYS_DOC_SUPPORT_2000
-#define CONFIG_SYS_DOC_SUPPORT_MILLENNIUM
-
 /*
  * Miscellaneous configurable options
  */
@@ -212,8 +200,6 @@
 
 #define CONFIG_SYS_HZ          1000            /* decrementer freq: 1 ms ticks */
 
-#define CONFIG_SYS_BAUDRATE_TABLE      { 9600, 19200, 38400, 57600, 115200 }
-
 #define CONFIG_SYS_RESET_ADDRESS 0xFDFFFFFC    /* "bad" address                */
 
 /*
@@ -296,9 +282,8 @@
  * Definitions for initial stack pointer and data area (in DPRAM)
  */
 #define CONFIG_SYS_INIT_RAM_ADDR       CONFIG_SYS_IMMR
-#define CONFIG_SYS_INIT_RAM_END        0x4000  /* End of used area in DPRAM    */
-#define CONFIG_SYS_GBL_DATA_SIZE       128 /* size in bytes reserved for initial data*/
-#define CONFIG_SYS_GBL_DATA_OFFSET     (CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE)
+#define CONFIG_SYS_INIT_RAM_SIZE       0x4000  /* Size of used area in DPRAM   */
+#define CONFIG_SYS_GBL_DATA_OFFSET     (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
 #define CONFIG_SYS_INIT_SP_OFFSET      CONFIG_SYS_GBL_DATA_OFFSET
 
 /*-----------------------------------------------------------------------
@@ -311,7 +296,7 @@
  */
 #define CONFIG_SYS_SDRAM_BASE          0x00000000
 #define CONFIG_SYS_FLASH_BASE          CONFIG_SYS_FLASH0_BASE
-#define CONFIG_SYS_MONITOR_BASE        TEXT_BASE
+#define CONFIG_SYS_MONITOR_BASE        CONFIG_SYS_TEXT_BASE
 #define CONFIG_SYS_MONITOR_LEN         (256 << 10)     /* Reserve 256 kB for Monitor */
 #define CONFIG_SYS_MALLOC_LEN          (128 << 10)     /* Reserve 128 kB for malloc()*/
 
@@ -325,15 +310,6 @@
 #define CONFIG_SYS_RX_ETH_BUFFER       8               /* use 8 rx buffer on eepro100  */
 #endif
 
-/*
- * Internal Definitions
- *
- * Boot Flags
- */
-#define BOOTFLAG_COLD          0x01    /* Normal Power-On: Boot from FLASH*/
-#define BOOTFLAG_WARM          0x02    /* Software reboot                 */
-
-
 /*-----------------------------------------------------------------------
  * Cache Configuration
  */