+++ /dev/null
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-#define CONFIG_SYS_TEXT_BASE 0x80F00000
-
-/*****************************************************************************
- *
- * These settings must match the way _your_ board is set up
- *
- *****************************************************************************/
-/* for the AY-Revision which does not use the HRCW */
-#define CONFIG_SYS_DEFAULT_IMMR 0x00010000
-
-/* What is the oscillator's (UX2) frequency in Hz? */
-#define CONFIG_8260_CLKIN (66 * 1000 * 1000)
-
-/* How is switch S2 set? We really only want the MODCK[1-3] bits, so
- * only the 3 least significant bits are important.
-*/
-#define CONFIG_SYS_SBC_S2 0x04
-
-/* What should MODCK_H be? It is dependent on the oscillator
- * frequency, MODCK[1-3], and desired CPM and core frequencies.
- * Some example values (all frequencies are in MHz):
- *
- * MODCK_H MODCK[1-3] Osc CPM Core
- * 0x2 0x2 33 133 133
- * 0x2 0x4 33 133 200
- * 0x5 0x5 66 133 133
- * 0x5 0x7 66 133 200
- */
-#define CONFIG_SYS_SBC_MODCK_H 0x06
-
-#define CONFIG_SYS_SBC_BOOT_LOW 1 /* only for HRCW */
-#undef CONFIG_SYS_SBC_BOOT_LOW
-
-/* What should the base address of the main FLASH be and how big is
- * it (in MBytes)? This must contain CONFIG_SYS_TEXT_BASE.
- * The main FLASH is whichever is connected to *CS0. U-Boot expects
- * this to be the SIMM.
- */
-#define CONFIG_SYS_FLASH0_BASE 0x80000000
-#define CONFIG_SYS_FLASH0_SIZE 16
-
-/* What should the base address of the secondary FLASH be and how big
- * is it (in Mbytes)? The secondary FLASH is whichever is connected
- * to *CS6. U-Boot expects this to be the on board FLASH. If you don't
- * want it enabled, don't define these constants.
- */
-#define CONFIG_SYS_FLASH1_BASE 0
-#define CONFIG_SYS_FLASH1_SIZE 0
-#undef CONFIG_SYS_FLASH1_BASE
-#undef CONFIG_SYS_FLASH1_SIZE
-
-/* What should be the base address of SDRAM DIMM and how big is
- * it (in Mbytes)?
-*/
-#define CONFIG_SYS_SDRAM0_BASE 0x00000000
-#define CONFIG_SYS_SDRAM0_SIZE 64
-
-/* What should be the base address of SDRAM DIMM and how big is
- * it (in Mbytes)?
-*/
-#define CONFIG_SYS_SDRAM1_BASE 0x04000000
-#define CONFIG_SYS_SDRAM1_SIZE 32
-
-/* What should be the base address of the LEDs and switch S0?
- * If you don't want them enabled, don't define this.
- */
-#define CONFIG_SYS_LED_BASE 0x00000000
-
-/*
- * select serial console configuration
- *
- * if either CONFIG_CONS_ON_SMC or CONFIG_CONS_ON_SCC is selected, then
- * CONFIG_CONS_INDEX must be set to the channel number (1-2 for SMC, 1-4
- * for SCC).
- *
- * if CONFIG_CONS_NONE is defined, then the serial console routines must
- * defined elsewhere.
- */
-#define CONFIG_CONS_ON_SMC /* define if console on SMC */
-#undef CONFIG_CONS_ON_SCC /* define if console on SCC */
-#undef CONFIG_CONS_NONE /* define if console on neither */
-#define CONFIG_CONS_INDEX 1 /* which SMC/SCC channel for console */
-
-/*
- * select ethernet configuration
- *
- * if either CONFIG_ETHER_ON_SCC or CONFIG_ETHER_ON_FCC is selected, then
- * CONFIG_ETHER_INDEX must be set to the channel number (1-4 for SCC, 1-3
- * for FCC)
- *
- * if CONFIG_ETHER_NONE is defined, then either the ethernet routines must be
- * defined elsewhere (as for the console), or CONFIG_CMD_NET must be unset.
- */
-#undef CONFIG_ETHER_ON_SCC /* define if ethernet on SCC */
-#define CONFIG_ETHER_ON_FCC /* define if ethernet on FCC */
-#undef CONFIG_ETHER_NONE /* define if ethernet on neither */
-#define CONFIG_ETHER_INDEX 3 /* which SCC/FCC channel for ethernet */
-
-#if ( CONFIG_ETHER_INDEX == 3 )
-
-/*
- * - Rx-CLK is CLK15
- * - Tx-CLK is CLK16
- * - RAM for BD/Buffers is on the 60x Bus (see 28-13)
- * - Enable Half Duplex in FSMR
- */
-# define CONFIG_SYS_CMXFCR_MASK3 (CMXFCR_FC3|CMXFCR_RF3CS_MSK|CMXFCR_TF3CS_MSK)
-# define CONFIG_SYS_CMXFCR_VALUE3 (CMXFCR_RF3CS_CLK15|CMXFCR_TF3CS_CLK16)
-# define CONFIG_SYS_CPMFCR_RAMTYPE 0
-/*#define CONFIG_SYS_FCC_PSMR (FCC_PSMR_FDE|FCC_PSMR_LPB) */
-# define CONFIG_SYS_FCC_PSMR 0
-
-#else /* CONFIG_ETHER_INDEX */
-# error "on RPX Super ethernet must be FCC3"
-#endif /* CONFIG_ETHER_INDEX */
-
-#define CONFIG_HARD_I2C 1 /* I2C with hardware support */
-#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */
-#define CONFIG_SYS_I2C_SLAVE 0x7F
-
-
-/* Define this to reserve an entire FLASH sector (256 KB) for
- * environment variables. Otherwise, the environment will be
- * put in the same sector as U-Boot, and changing variables
- * will erase U-Boot temporarily
- */
-#define CONFIG_ENV_IN_OWN_SECT
-
-/* Define to allow the user to overwrite serial and ethaddr */
-#define CONFIG_ENV_OVERWRITE
-
-/* What should the console's baud rate be? */
-#define CONFIG_BAUDRATE 115200
-
-/* Ethernet MAC address */
-#define CONFIG_ETHADDR 08:00:22:50:70:63
-
-#define CONFIG_IPADDR 192.168.1.99
-#define CONFIG_SERVERIP 192.168.1.3
-
-/* Set to a positive value to delay for running BOOTCOMMAND */
-#define CONFIG_BOOTDELAY -1
-
-/* undef this to save memory */
-#define CONFIG_SYS_LONGHELP
-
-/* Monitor Command Prompt */
-
-
-/*
- * BOOTP options
- */
-#define CONFIG_BOOTP_BOOTFILESIZE
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
-
-
-/*
- * Command line configuration.
- */
-#include <config_cmd_default.h>
-
-#define CONFIG_CMD_IMMAP
-#define CONFIG_CMD_ASKENV
-#define CONFIG_CMD_I2C
-#define CONFIG_CMD_REGINFO
-
-#undef CONFIG_CMD_KGDB
-
-
-/* Where do the internal registers live? */
-#define CONFIG_SYS_IMMR 0xF0000000
-
-/* Where do the on board registers (CS4) live? */
-#define CONFIG_SYS_REGS_BASE 0xFA000000
-
-/*****************************************************************************
- *
- * You should not have to modify any of the following settings
- *
- *****************************************************************************/
-
-#define CONFIG_RPXSUPER 1 /* on an Embedded Planet RPX Super Board */
-#define CONFIG_CPM2 1 /* Has a CPM2 */
-
-#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_early_init_f */
-#define CONFIG_RESET_PHY_R 1 /* Call reset_phy() */
-
-/*
- * Miscellaneous configurable options
- */
-#if defined(CONFIG_CMD_KGDB)
-# define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
-#else
-# define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
-#endif
-
-/* Print Buffer Size */
-#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT)+16)
-
-#define CONFIG_SYS_MAXARGS 8 /* max number of command args */
-
-#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
-
-#define CONFIG_SYS_MEMTEST_START 0x04000000 /* memtest works on */
-#define CONFIG_SYS_MEMTEST_END 0x06000000 /* 64-96 MB in SDRAM */
-
-#define CONFIG_CLOCKS_IN_MHZ 1 /* clocks passsed to Linux in MHz */
-
-#define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */
-
-/*
- * Low Level Configuration Settings
- * (address mappings, register initial values, etc.)
- * You should know what you are doing if you make changes here.
- */
-
-#define CONFIG_SYS_FLASH_BASE CONFIG_SYS_FLASH0_BASE
-#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_SDRAM0_BASE
-
-/*-----------------------------------------------------------------------
- * Hard Reset Configuration Words
- */
-#if defined(CONFIG_SYS_SBC_BOOT_LOW)
-# define CONFIG_SYS_SBC_HRCW_BOOT_FLAGS (HRCW_CIP | HRCW_BMS)
-#else
-# define CONFIG_SYS_SBC_HRCW_BOOT_FLAGS (0)
-#endif /* defined(CONFIG_SYS_SBC_BOOT_LOW) */
-
-/* get the HRCW ISB field from CONFIG_SYS_IMMR */
-#define CONFIG_SYS_SBC_HRCW_IMMR ( ((CONFIG_SYS_IMMR & 0x10000000) >> 10) |\
- ((CONFIG_SYS_IMMR & 0x01000000) >> 7) |\
- ((CONFIG_SYS_IMMR & 0x00100000) >> 4) )
-
-#define CONFIG_SYS_HRCW_MASTER (HRCW_BPS11 |\
- HRCW_DPPC11 |\
- CONFIG_SYS_SBC_HRCW_IMMR |\
- HRCW_MMR00 |\
- HRCW_LBPC11 |\
- HRCW_APPC10 |\
- HRCW_CS10PC00 |\
- (CONFIG_SYS_SBC_MODCK_H & HRCW_MODCK_H1111) |\
- CONFIG_SYS_SBC_HRCW_BOOT_FLAGS)
-
-/* no slaves */
-#define CONFIG_SYS_HRCW_SLAVE1 0
-#define CONFIG_SYS_HRCW_SLAVE2 0
-#define CONFIG_SYS_HRCW_SLAVE3 0
-#define CONFIG_SYS_HRCW_SLAVE4 0
-#define CONFIG_SYS_HRCW_SLAVE5 0
-#define CONFIG_SYS_HRCW_SLAVE6 0
-#define CONFIG_SYS_HRCW_SLAVE7 0
-
-/*-----------------------------------------------------------------------
- * Definitions for initial stack pointer and data area (in DPRAM)
- */
-#define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_IMMR
-#define CONFIG_SYS_INIT_RAM_SIZE 0x4000 /* Size of used area in DPRAM */
-#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
-#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
-
-/*-----------------------------------------------------------------------
- * Start addresses for the final memory configuration
- * (Set up by the startup code)
- * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
- * Note also that the logic that sets CONFIG_SYS_RAMBOOT is platform dependent.
- */
-#define CONFIG_SYS_MONITOR_BASE (CONFIG_SYS_FLASH0_BASE + 0x00F00000)
-
-#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE)
-# define CONFIG_SYS_RAMBOOT
-#endif
-
-#define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */
-#define CONFIG_SYS_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */
-
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 8 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
-
-/*-----------------------------------------------------------------------
- * FLASH and environment organization
- */
-#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */
-#define CONFIG_SYS_MAX_FLASH_SECT 71 /* max number of sectors on one chip */
-
-#define CONFIG_SYS_FLASH_ERASE_TOUT 8000 /* Timeout for Flash Erase (in ms) */
-#define CONFIG_SYS_FLASH_WRITE_TOUT 1 /* Timeout for Flash Write (in ms) */
-
-#ifndef CONFIG_SYS_RAMBOOT
-# define CONFIG_ENV_IS_IN_FLASH 1
-
-# ifdef CONFIG_ENV_IN_OWN_SECT
-# define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE + 0x40000)
-# define CONFIG_ENV_SECT_SIZE 0x40000
-# else
-# define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + CONFIG_SYS_MONITOR_LEN - CONFIG_ENV_SECT_SIZE)
-# define CONFIG_ENV_SIZE 0x1000 /* Total Size of Environment Sector */
-# define CONFIG_ENV_SECT_SIZE 0x10000 /* see README - env sect real size */
-# endif /* CONFIG_ENV_IN_OWN_SECT */
-#else
-# define CONFIG_ENV_IS_IN_NVRAM 1
-# define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - 0x1000)
-# define CONFIG_ENV_SIZE 0x200
-#endif /* CONFIG_SYS_RAMBOOT */
-
-/*-----------------------------------------------------------------------
- * Cache Configuration
- */
-#define CONFIG_SYS_CACHELINE_SIZE 32 /* For MPC8260 CPU */
-
-#if defined(CONFIG_CMD_KGDB)
-# define CONFIG_SYS_CACHELINE_SHIFT 5 /* log base 2 of the above value */
-#endif
-
-/*-----------------------------------------------------------------------
- * HIDx - Hardware Implementation-dependent Registers 2-11
- *-----------------------------------------------------------------------
- * HID0 also contains cache control - initially enable both caches and
- * invalidate contents, then the final state leaves only the instruction
- * cache enabled. Note that Power-On and Hard reset invalidate the caches,
- * but Soft reset does not.
- *
- * HID1 has only read-only information - nothing to set.
- */
-#define CONFIG_SYS_HID0_INIT (/*HID0_ICE |*/\
- /*HID0_DCE |*/\
- HID0_ICFI |\
- HID0_DCI |\
- HID0_IFEM |\
- HID0_ABE)
-
-#define CONFIG_SYS_HID0_FINAL (/*HID0_ICE |*/\
- HID0_IFEM |\
- HID0_ABE |\
- HID0_EMCP)
-#define CONFIG_SYS_HID2 0
-
-/*-----------------------------------------------------------------------
- * RMR - Reset Mode Register
- *-----------------------------------------------------------------------
- */
-#define CONFIG_SYS_RMR 0
-
-/*-----------------------------------------------------------------------
- * BCR - Bus Configuration 4-25
- *-----------------------------------------------------------------------
- */
-#define CONFIG_SYS_BCR (BCR_EBM |\
- BCR_PLDP |\
- BCR_EAV |\
- BCR_NPQM0)
-
-/*-----------------------------------------------------------------------
- * SIUMCR - SIU Module Configuration 4-31
- *-----------------------------------------------------------------------
- */
-
-#define CONFIG_SYS_SIUMCR (SIUMCR_L2CPC01 |\
- SIUMCR_APPC10 |\
- SIUMCR_CS10PC01)
-
-
-/*-----------------------------------------------------------------------
- * SYPCR - System Protection Control 11-9
- * SYPCR can only be written once after reset!
- *-----------------------------------------------------------------------
- * Watchdog & Bus Monitor Timer max, 60x Bus Monitor enable
- */
-#define CONFIG_SYS_SYPCR (SYPCR_SWTC |\
- SYPCR_BMT |\
- SYPCR_PBME |\
- SYPCR_LBME |\
- SYPCR_SWRI |\
- SYPCR_SWP)
-
-/*-----------------------------------------------------------------------
- * TMCNTSC - Time Counter Status and Control 4-40
- *-----------------------------------------------------------------------
- * Clear once per Second and Alarm Interrupt Status, Set 32KHz timersclk,
- * and enable Time Counter
- */
-#define CONFIG_SYS_TMCNTSC (TMCNTSC_SEC |\
- TMCNTSC_ALR |\
- TMCNTSC_TCF |\
- TMCNTSC_TCE)
-
-/*-----------------------------------------------------------------------
- * PISCR - Periodic Interrupt Status and Control 4-42
- *-----------------------------------------------------------------------
- * Clear Periodic Interrupt Status, Set 32KHz timersclk, and enable
- * Periodic timer
- */
-#define CONFIG_SYS_PISCR (PISCR_PS |\
- PISCR_PTF |\
- PISCR_PTE)
-
-/*-----------------------------------------------------------------------
- * SCCR - System Clock Control 9-8
- *-----------------------------------------------------------------------
- */
-#define CONFIG_SYS_SCCR (SCCR_DFBRG01)
-
-/*-----------------------------------------------------------------------
- * RCCR - RISC Controller Configuration 13-7
- *-----------------------------------------------------------------------
- */
-#define CONFIG_SYS_RCCR 0
-
-/*
- * Init Memory Controller:
- *
- * Bank Bus Machine PortSz Device
- * ---- --- ------- ------ ------
- * 0 60x GPCM 64 bit FLASH (BGA - 16MB AMD AM29DL323DB90)
- * 1 60x SDRAM 64 bit SDRAM (BGA - 64MB Hitachi HM5225325FBP-B60)
- * 2 Local SDRAM 32 bit SDRAM (BGA - 32MB Hitachi HM5225325FBP-B60)
- * 3 unused
- * 4 60x GPCM 8 bit Board Regs, LEDs, switches
- * 5 unused
- * 6 unused
- * 7 unused
- * 8 PCMCIA
- * 9 unused
- * 10 unused
- * 11 unused
-*/
-
-/* Bank 0 - FLASH
- *
- */
-#define CONFIG_SYS_BR0_PRELIM ((CONFIG_SYS_FLASH0_BASE & BRx_BA_MSK) |\
- BRx_PS_64 |\
- BRx_DECC_NONE |\
- BRx_MS_GPCM_P |\
- BRx_V)
-
-#define CONFIG_SYS_OR0_PRELIM (MEG_TO_AM(CONFIG_SYS_FLASH0_SIZE) |\
- ORxG_CSNT |\
- ORxG_ACS_DIV1 |\
- ORxG_SCY_6_CLK |\
- ORxG_EHTR)
-
-/* Bank 1 - SDRAM
- *
- */
-#define CONFIG_SYS_BR1_PRELIM ((CONFIG_SYS_SDRAM0_BASE & BRx_BA_MSK) |\
- BRx_PS_64 |\
- BRx_MS_SDRAM_P |\
- BRx_V)
-
-#define CONFIG_SYS_OR1_PRELIM (MEG_TO_AM(CONFIG_SYS_SDRAM0_SIZE) |\
- ORxS_BPD_4 |\
- ORxS_ROWST_PBI0_A8 |\
- ORxS_NUMR_12 |\
- ORxS_IBID)
-
-#define CONFIG_SYS_PSDMR 0x014DA412
-#define CONFIG_SYS_PSRT 0x79
-
-
-/* Bank 2 - SDRAM
- *
- */
-#define CONFIG_SYS_BR2_PRELIM ((CONFIG_SYS_SDRAM1_BASE & BRx_BA_MSK) |\
- BRx_PS_32 |\
- BRx_MS_SDRAM_L |\
- BRx_V)
-
-#define CONFIG_SYS_OR2_PRELIM (MEG_TO_AM(CONFIG_SYS_SDRAM1_SIZE) |\
- ORxS_BPD_4 |\
- ORxS_ROWST_PBI0_A9 |\
- ORxS_NUMR_12)
-
-#define CONFIG_SYS_LSDMR 0x0169A512
-#define CONFIG_SYS_LSRT 0x79
-
-#define CONFIG_SYS_MPTPR (0x0800 & MPTPR_PTP_MSK)
-
-/* Bank 4 - On board registers
- *
- */
-#define CONFIG_SYS_BR4_PRELIM ((CONFIG_SYS_REGS_BASE & BRx_BA_MSK) |\
- BRx_PS_8 |\
- BRx_MS_GPCM_P |\
- BRx_V)
-
-#define CONFIG_SYS_OR4_PRELIM (ORxG_AM_MSK |\
- ORxG_CSNT |\
- ORxG_ACS_DIV1 |\
- ORxG_SCY_5_CLK |\
- ORxG_TRLX)
-
-#endif /* __CONFIG_H */
projects / karo-tx-uboot.git / blobdiff