#ifndef __CONFIG_EZKIT533_H__
#define __CONFIG_EZKIT533_H__
+#include <asm/blackfin-config-pre.h>
+
#define CONFIG_BAUDRATE 57600
-#define CONFIG_STAMP 1
#define CONFIG_BOOTDELAY 5
-#define CFG_AUTOLOAD "no" /*rarpb, bootp or dhcp commands will perform only a */
+#define CONFIG_SYS_AUTOLOAD "no" /*rarpb, bootp or dhcp commands will perform only a */
-#define CFG_LONGHELP 1
+#define CONFIG_SYS_LONGHELP 1
#define CONFIG_CMDLINE_EDITING 1
#define CONFIG_LOADADDR 0x01000000 /* default load address */
#define CONFIG_BOOTCOMMAND "tftp $(loadaddr) linux"
#if 0
#define CONFIG_MII
-#define CFG_DISCOVER_PHY
+#define CONFIG_SYS_DISCOVER_PHY
#endif
#define CONFIG_RTC_BFIN 1
#define CONFIG_BOOT_RETRY_TIME -1 /* Enable this if bootretry required, currently its disabled */
-/*
- * Boot Mode Set
- * Blackfin can support several boot modes
- */
-#define BF533_BYPASS_BOOT 0x0001 /* Bootmode 0: Execute from 16-bit externeal memory ( bypass BOOT ROM) */
-#define BF533_PARA_BOOT 0x0002 /* Bootmode 1: Boot from 8-bit or 16-bit flash */
-#define BF533_SPI_BOOT 0x0004 /* Bootmode 3: Boot from SPI flash */
-/* Define the boot mode */
-#define BFIN_BOOT_MODE BF533_BYPASS_BOOT
-/* #define BFIN_BOOT_MODE BF533_SPI_BOOT */
-
#define CONFIG_PANIC_HANG 1
-#define ADSP_BF531 0x31
-#define ADSP_BF532 0x32
-#define ADSP_BF533 0x33
-#define BFIN_CPU ADSP_BF533
+#define CONFIG_BFIN_CPU bf533-0.3
+#define CONFIG_BFIN_BOOT_MODE BFIN_BOOT_BYPASS
/* This sets the default state of the cache on U-Boot's boot */
#define CONFIG_ICACHE_ON
#define CONFIG_DCACHE_ON
-/* Define where the uboot will be loaded by on-chip boot rom */
-#define APP_ENTRY 0x00001000
-
/* CONFIG_CLKIN_HZ is any value in Hz */
#define CONFIG_CLKIN_HZ 27000000
/* CONFIG_CLKIN_HALF controls what is passed to PLL 0=CLKIN */
#define CONFIG_BOOTARGS "root=/dev/mtdblock0 ip=192.168.0.15:192.168.0.2:192.168.0.1:255.255.255.0:ezkit:eth0:off console=ttyBF0,57600"
-#define CFG_PROMPT "ezkit> " /* Monitor Command Prompt */
+#define CONFIG_SYS_PROMPT "bfin> " /* Monitor Command Prompt */
#if defined(CONFIG_CMD_KGDB)
-#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
+#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
#else
-#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
+#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
#endif
-#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
-#define CFG_MAXARGS 16 /* max number of command args */
-#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
-#define CFG_MEMTEST_START 0x00000000 /* memtest works on */
-#define CFG_MEMTEST_END ( (CONFIG_MEM_SIZE - 1) * 1024 * 1024) /* 1 ... 31 MB in DRAM */
-#define CFG_LOAD_ADDR 0x01000000 /* default load address */
-#define CFG_HZ 1000 /* decrementer freq: 10 ms ticks */
-#define CFG_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 }
-#define CFG_SDRAM_BASE 0x00000000
-#define CFG_MAX_RAM_SIZE (CONFIG_MEM_SIZE * 1024 * 1024)
-#define CFG_FLASH_BASE 0x20000000
-
-#define CFG_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */
-#define CFG_MONITOR_BASE (CFG_MAX_RAM_SIZE - CFG_MONITOR_LEN)
-#define CFG_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */
-#define CFG_MALLOC_BASE (CFG_MONITOR_BASE - CFG_MALLOC_LEN)
-#define CFG_GBL_DATA_SIZE 0x4000
-#define CFG_GBL_DATA_ADDR (CFG_MALLOC_BASE - CFG_GBL_DATA_SIZE)
-#define CONFIG_STACKBASE (CFG_GBL_DATA_ADDR - 4)
-
-#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
-#define CFG_FLASH0_BASE 0x20000000
-#define CFG_FLASH1_BASE 0x20200000
-#define CFG_FLASH2_BASE 0x20280000
-#define CFG_MAX_FLASH_BANKS 3 /* max number of memory banks */
-#define CFG_MAX_FLASH_SECT 40 /* max number of sectors on one chip */
-
-#define CFG_ENV_IS_IN_FLASH 1
-#define CFG_ENV_ADDR 0x20020000
-#define CFG_ENV_SECT_SIZE 0x10000 /* Total Size of Environment Sector */
+#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
+#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
+#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
+#define CONFIG_SYS_MEMTEST_START 0x00000000 /* memtest works on */
+#define CONFIG_SYS_MEMTEST_END ( (CONFIG_MEM_SIZE - 1) * 1024 * 1024) /* 1 ... 31 MB in DRAM */
+#define CONFIG_SYS_LOAD_ADDR 0x01000000 /* default load address */
+#define CONFIG_SYS_HZ 1000 /* decrementer freq: 10 ms ticks */
+#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 }
+#define CONFIG_SYS_SDRAM_BASE 0x00000000
+#define CONFIG_SYS_MAX_RAM_SIZE (CONFIG_MEM_SIZE * 1024 * 1024)
+#define CONFIG_SYS_FLASH_BASE 0x20000000
+
+#define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */
+#define CONFIG_SYS_MONITOR_BASE (CONFIG_SYS_MAX_RAM_SIZE - CONFIG_SYS_MONITOR_LEN)
+#define CONFIG_SYS_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */
+#define CONFIG_SYS_MALLOC_BASE (CONFIG_SYS_MONITOR_BASE - CONFIG_SYS_MALLOC_LEN)
+#define CONFIG_SYS_GBL_DATA_SIZE 0x4000
+#define CONFIG_SYS_GBL_DATA_ADDR (CONFIG_SYS_MALLOC_BASE - CONFIG_SYS_GBL_DATA_SIZE)
+#define CONFIG_STACKBASE (CONFIG_SYS_GBL_DATA_ADDR - 4)
+
+#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
+#define CONFIG_SYS_FLASH0_BASE 0x20000000
+#define CONFIG_SYS_FLASH1_BASE 0x20200000
+#define CONFIG_SYS_FLASH2_BASE 0x20280000
+#define CONFIG_SYS_MAX_FLASH_BANKS 3 /* max number of memory banks */
+#define CONFIG_SYS_MAX_FLASH_SECT 40 /* max number of sectors on one chip */
+
+#define CONFIG_ENV_IS_IN_FLASH 1
+#define CONFIG_ENV_ADDR 0x20020000
+#define CONFIG_ENV_SECT_SIZE 0x10000 /* Total Size of Environment Sector */
/* JFFS Partition offset set */
-#define CFG_JFFS2_FIRST_BANK 0
-#define CFG_JFFS2_NUM_BANKS 1
+#define CONFIG_SYS_JFFS2_FIRST_BANK 0
+#define CONFIG_SYS_JFFS2_NUM_BANKS 1
/* 512k reserved for u-boot */
-#define CFG_JFFS2_FIRST_SECTOR 11
+#define CONFIG_SYS_JFFS2_FIRST_SECTOR 11
/*
#define POLL_MODE 1
#define FLASH_TOT_SECT 40
#define FLASH_SIZE 0x220000
-#define CFG_FLASH_SIZE 0x220000
+#define CONFIG_SYS_FLASH_SIZE 0x220000
/*
* Initialize PSD4256 registers for using I2C
}
#define I2C_DELAY udelay(5) /* 1/4 I2C clock duration */
-#define CFG_I2C_SPEED 50000
-#define CFG_I2C_SLAVE 0xFE
-
-#define CFG_BOOTM_LEN 0x4000000 /* Large Image Length, set to 64 Meg */
-
-/* 0xFF, 0x7BB07BB0, 0x22547BB0 */
-/* #define AMGCTLVAL (AMBEN_P0 | AMBEN_P1 | AMBEN_P2 | AMCKEN)
-#define AMBCTL0VAL (B1WAT_7 | B1RAT_11 | B1HT_2 | B1ST_3 | B1TT_4 | ~B1RDYPOL | \
- ~B1RDYEN | B0WAT_7 | B0RAT_11 | B0HT_2 | B0ST_3 | B0TT_4 | ~B0RDYPOL | ~B0RDYEN)
-#define AMBCTL1VAL (B3WAT_2 | B3RAT_2 | B3HT_1 | B3ST_1 | B3TT_4 | B3RDYPOL | ~B3RDYEN | \
- B2WAT_7 | B2RAT_11 | B2HT_2 | B2ST_3 | B2TT_4 | ~B2RDYPOL | ~B2RDYEN)
-*/
-#define AMGCTLVAL 0xFF
-#define AMBCTL0VAL 0x7BB07BB0
-#define AMBCTL1VAL 0xFFC27BB0
-
-#define CONFIG_VDSP 1
-
-#ifdef CONFIG_VDSP
-#define ET_EXEC_VDSP 0x8
-#define SHT_STRTAB_VDSP 0x1
-#define ELFSHDRSIZE_VDSP 0x2C
-#define VDSP_ENTRY_ADDR 0xFFA00000
-#endif
+#define CONFIG_SYS_I2C_SPEED 50000
+#define CONFIG_SYS_I2C_SLAVE 0xFE
+
+#define CONFIG_SYS_BOOTM_LEN 0x4000000 /* Large Image Length, set to 64 Meg */
+
+#define CONFIG_EBIU_SDRRC_VAL 0x398
+#define CONFIG_EBIU_SDGCTL_VAL 0x91118d
+#define CONFIG_EBIU_SDBCTL_VAL 0x13
+
+#define CONFIG_EBIU_AMGCTL_VAL 0xFF
+#define CONFIG_EBIU_AMBCTL0_VAL 0x7BB07BB0
+#define CONFIG_EBIU_AMBCTL1_VAL 0xFFC27BB0
+
+#include <asm/blackfin-config-post.h>
#endif
projects / karo-tx-uboot.git / blobdiff