fs: Add command to retrieve the filesystem type

[karo-tx-uboot.git] / include / configs / cm_t35.h

diff --git a/include/configs/cm_t35.h b/include/configs/cm_t35.h
index cfc4f9bb8ebb2856c6508ca1e0c304d876453cfb..9767512a5cf03771a5008932433b417cdacfbe56 100644 (file)
--- a/include/configs/cm_t35.h
+++ b/include/configs/cm_t35.h
@@ -21,11 +21,11 @@
  * High Level Configuration Options
  */
 #define CONFIG_OMAP    /* in a TI OMAP core */
-#define CONFIG_OMAP34XX        /* which is a 34XX */
 #define CONFIG_OMAP_GPIO
 #define CONFIG_CMD_GPIO
 #define CONFIG_CM_T3X  /* working with CM-T35 and CM-T3730 */
 #define CONFIG_OMAP_COMMON
+#define CONFIG_SYS_GENERIC_BOARD
 
 #define CONFIG_SDRC    /* The chip has SDRC controller */
 
@@ -104,8 +104,6 @@
 #define CONFIG_USB_DEVICE
 #define CONFIG_USB_TTY
 #define CONFIG_SYS_CONSOLE_IS_IN_ENV
-/* This delay is really for slow-to-power-on USB sticks, not the hub */
-#define CONFIG_USB_HUB_MIN_POWER_ON_DELAY 500
 
 /* commands to include */
 #include <config_cmd_default.h>
@@ -138,6 +136,7 @@
 #define CONFIG_SYS_I2C_OMAP34XX
 #define CONFIG_SYS_I2C_EEPROM_ADDR     0x50
 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
+#define CONFIG_SYS_I2C_EEPROM_BUS      0
 #define CONFIG_I2C_MULTI_BUS
 
 /*
@@ -158,6 +157,7 @@
                                                        /* CS0 */
 #define CONFIG_SYS_MAX_NAND_DEVICE     1               /* Max number of NAND */
                                                        /* devices */
+
 /* Environment information */
 #define CONFIG_BOOTDELAY               3
 #define CONFIG_ZERO_BOOTDELAY_CHECK
@@ -259,9 +259,6 @@
  */
 
 /* **** PISMO SUPPORT *** */
-/* Configure the PISMO */
-#define PISMO1_NAND_SIZE               GPMC_SIZE_128M
-
 /* Monitor at start of flash */
 #define CONFIG_SYS_MONITOR_BASE                CONFIG_SYS_FLASH_BASE
 #define CONFIG_SYS_MONITOR_LEN         (256 << 10)     /* Reserve 2 sectors */
@@ -320,14 +317,13 @@
 #define CONFIG_OMAP3_SPI
 
 /* Defines for SPL */
-#define CONFIG_SPL
 #define CONFIG_SPL_FRAMEWORK
 #define CONFIG_SPL_NAND_SIMPLE
 
 #define CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR        0x300 /* address 0x60000 */
 #define CONFIG_SYS_U_BOOT_MAX_SIZE_SECTORS     0x200 /* 256 KB */
-#define CONFIG_SYS_MMC_SD_FAT_BOOT_PARTITION   1
-#define CONFIG_SPL_FAT_LOAD_PAYLOAD_NAME       "u-boot.img"
+#define CONFIG_SYS_MMCSD_FS_BOOT_PARTITION     1
+#define CONFIG_SPL_FS_LOAD_PAYLOAD_NAME        "u-boot.img"
 
 #define CONFIG_SPL_BOARD_INIT
 #define CONFIG_SPL_LIBCOMMON_SUPPORT