*
* Configuration settings for the CompuLab CM-T35 and CM-T3730 boards
*
- * See file CREDITS for list of people who contributed to this
- * project.
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc.
+ * SPDX-License-Identifier: GPL-2.0+
*/
#ifndef __CONFIG_H
*/
#define CONFIG_OMAP /* in a TI OMAP core */
#define CONFIG_OMAP34XX /* which is a 34XX */
+#define CONFIG_OMAP_GPIO
+#define CONFIG_CMD_GPIO
#define CONFIG_CM_T3X /* working with CM-T35 and CM-T3730 */
+#define CONFIG_OMAP_COMMON
#define CONFIG_SYS_TEXT_BASE 0x80008000
#define V_OSCK 26000000 /* Clock output from T2 */
#define V_SCLK (V_OSCK >> 1)
-#undef CONFIG_USE_IRQ /* no support for IRQs */
#define CONFIG_MISC_INIT_R
#define CONFIG_OF_LIBFDT 1
#define CONFIG_DOS_PARTITION
/* USB */
-#define CONFIG_MUSB_UDC
#define CONFIG_USB_OMAP3
+#define CONFIG_USB_EHCI
+#define CONFIG_USB_EHCI_OMAP
+#define CONFIG_USB_ULPI
+#define CONFIG_USB_ULPI_VIEWPORT_OMAP
+#define CONFIG_USB_STORAGE
+#define CONFIG_MUSB_UDC
#define CONFIG_TWL4030_USB
+#define CONFIG_CMD_USB
/* USB device configuration */
#define CONFIG_USB_DEVICE
#define CONFIG_CMD_CACHE
#define CONFIG_CMD_EXT2 /* EXT2 Support */
#define CONFIG_CMD_FAT /* FAT support */
-#define CONFIG_CMD_JFFS2 /* JFFS2 Support */
#define CONFIG_CMD_MTDPARTS /* Enable MTD parts commands */
#define CONFIG_MTD_DEVICE /* needed for mtdparts commands */
+#define CONFIG_MTD_PARTITIONS
#define MTDIDS_DEFAULT "nand0=nand"
#define MTDPARTS_DEFAULT "mtdparts=nand:512k(x-loader),"\
- "1920k(u-boot),128k(u-boot-env),"\
+ "1920k(u-boot),256k(u-boot-env),"\
"4m(kernel),-(fs)"
#define CONFIG_CMD_I2C /* I2C serial bus support */
#undef CONFIG_CMD_IMLS /* List all found images */
#define CONFIG_SYS_NO_FLASH
-#define CONFIG_HARD_I2C
-#define CONFIG_SYS_I2C_SPEED 100000
-#define CONFIG_SYS_I2C_SLAVE 1
-#define CONFIG_SYS_I2C_BUS 0
-#define CONFIG_SYS_I2C_BUS_SELECT 1
-#define CONFIG_DRIVER_OMAP34XX_I2C
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_OMAP24_I2C_SPEED 100000
+#define CONFIG_SYS_OMAP24_I2C_SLAVE 1
+#define CONFIG_SYS_I2C_OMAP34XX
#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50
#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
#define CONFIG_I2C_MULTI_BUS
#define CONFIG_SYS_MAX_NAND_DEVICE 1 /* Max number of NAND */
/* devices */
-#define CONFIG_JFFS2_NAND
-/* nand device jffs2 lives on */
-#define CONFIG_JFFS2_DEV "nand0"
-/* start of jffs2 partition */
-#define CONFIG_JFFS2_PART_OFFSET 0x680000
-#define CONFIG_JFFS2_PART_SIZE 0xf980000 /* size of jffs2 */
- /* partition */
-
/* Environment information */
-#define CONFIG_BOOTDELAY 10
+#define CONFIG_BOOTDELAY 3
+#define CONFIG_ZERO_BOOTDELAY_CHECK
#define CONFIG_EXTRA_ENV_SETTINGS \
"loadaddr=0x82000000\0" \
"defaultdisplay=dvi\0" \
"mmcdev=0\0" \
"mmcroot=/dev/mmcblk0p2 rw\0" \
- "mmcrootfstype=ext3 rootwait\0" \
+ "mmcrootfstype=ext4 rootwait\0" \
"nandroot=/dev/mtdblock4 rw\0" \
- "nandrootfstype=jffs2\0" \
+ "nandrootfstype=ubifs\0" \
"mmcargs=setenv bootargs console=${console} " \
"mpurate=${mpurate} " \
"vram=${vram} " \
"bootm ${loadaddr}\0" \
"nandboot=echo Booting from nand ...; " \
"run nandargs; " \
- "nand read ${loadaddr} 280000 400000; " \
+ "nand read ${loadaddr} 2a0000 400000; " \
"bootm ${loadaddr}\0" \
#define CONFIG_BOOTCOMMAND \
- "if mmc rescan ${mmcdev}; then " \
+ "mmc dev ${mmcdev}; if mmc rescan; then " \
"if run loadbootscript; then " \
"run bootscript; " \
"else " \
*/
#define CONFIG_SYS_TIMERBASE (OMAP34XX_GPT2)
#define CONFIG_SYS_PTV 2 /* Divisor: 2^(PTV+1) => 8 */
-#define CONFIG_SYS_HZ 1000
-
-/*-----------------------------------------------------------------------
- * Stack sizes
- *
- * The stack sizes are set up in start.S using the settings below
- */
-#define CONFIG_STACKSIZE (128 << 10) /* regular stack 128 KiB */
/*-----------------------------------------------------------------------
* Physical Memory Map
*/
#define CONFIG_NR_DRAM_BANKS 1 /* CS1 is never populated */
#define PHYS_SDRAM_1 OMAP34XX_SDRC_CS0
-#define PHYS_SDRAM_1_SIZE (32 << 20) /* at least 32 MiB */
/*-----------------------------------------------------------------------
* FLASH and environment organization
*/
/* **** PISMO SUPPORT *** */
-
/* Configure the PISMO */
#define PISMO1_NAND_SIZE GPMC_SIZE_128M
-#define PISMO1_ONEN_SIZE GPMC_SIZE_128M
-
-#define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 2 sectors */
-
-#if defined(CONFIG_CMD_NAND)
-#define CONFIG_SYS_FLASH_BASE PISMO1_NAND_BASE
-#endif
/* Monitor at start of flash */
#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE
-#define CONFIG_SYS_ONENAND_BASE ONENAND_MAP
+#define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 2 sectors */
#define CONFIG_ENV_IS_IN_NAND
-#define ONENAND_ENV_OFFSET 0x260000 /* environment starts here */
#define SMNAND_ENV_OFFSET 0x260000 /* environment starts here */
-
#define CONFIG_ENV_OFFSET SMNAND_ENV_OFFSET
#define CONFIG_ENV_ADDR SMNAND_ENV_OFFSET
/* Status LED */
#define CONFIG_STATUS_LED /* Status LED enabled */
#define CONFIG_BOARD_SPECIFIC_LED
-#define STATUS_LED_GREEN 0
-#define STATUS_LED_BIT STATUS_LED_GREEN
+#define CONFIG_GPIO_LED
+#define GREEN_LED_GPIO 186 /* CM-T35 Green LED is GPIO186 */
+#define GREEN_LED_DEV 0
+#define STATUS_LED_BIT GREEN_LED_GPIO
#define STATUS_LED_STATE STATUS_LED_ON
#define STATUS_LED_PERIOD (CONFIG_SYS_HZ / 2)
-#define STATUS_LED_BOOT STATUS_LED_BIT
-#define GREEN_LED_GPIO 186 /* CM-T35 Green LED is GPIO186 */
+#define STATUS_LED_BOOT GREEN_LED_DEV
+
+#define CONFIG_SPLASHIMAGE_GUARD
/* GPIO banks */
#ifdef CONFIG_STATUS_LED
#define CONFIG_OMAP3_GPIO_6 /* GPIO186 is in GPIO bank 6 */
#endif
+/* Display Configuration */
+#define CONFIG_OMAP3_GPIO_2
+#define CONFIG_VIDEO_OMAP3
+#define LCD_BPP LCD_COLOR16
+
+#define CONFIG_LCD
+#define CONFIG_SPLASH_SCREEN
+#define CONFIG_CMD_BMP
+#define CONFIG_BMP_16BPP
+#define CONFIG_SCF0403_LCD
+
+#define CONFIG_OMAP3_SPI
+
#endif /* __CONFIG_H */