* Marvell Semiconductor <www.marvell.com>
* Written-by: Prafulla Wadaskar <prafulla@marvell.com>
*
- * See file CREDITS for list of people who contributed to this
- * project.
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
- * MA 02110-1301 USA
+ * SPDX-License-Identifier: GPL-2.0+
*/
#ifndef _CONFIG_EDMINIV2_H
* - GPIO16 is Power LED control (0 = on, 1 = off)
* - GPIO17 is Power LED source select (0 = CPLD, 1 = GPIO16)
* - GPIO18 is Power Button status (0 = Released, 1 = Pressed)
- * - Last GPIO is 26, further bits are supposed to be 0.
+ * - GPIO19 is SATA disk power toggle (toggles on 0-to-1)
+ * - GPIO22 is SATA disk power status ()
+ * - GPIO23 is supply status for SATA disk ()
+ * - GPIO24 is supply control for board (write 1 to power off)
+ * Last GPIO is 25, further bits are supposed to be 0.
* Enable mask has ones for INPUT, 0 for OUTPUT.
- * Default is LED ON.
+ * Default is LED ON, board ON :)
*/
-#define ORION5X_GPIO_OUT_ENABLE 0x03fcffff
-#define ORION5X_GPIO_OUT_VALUE 0x03fcffff
+#define ORION5X_GPIO_OUT_ENABLE 0xfef4f0ca
+#define ORION5X_GPIO_OUT_VALUE 0x00000000
+#define ORION5X_GPIO_IN_POLARITY 0x000000d0
/*
* NS16550 Configuration
#include <config_cmd_default.h>
#define CONFIG_CMD_IDE
#define CONFIG_CMD_I2C
+#define CONFIG_CMD_USB
/*
* Network
/* end of IDE defines */
#endif /* CMD_IDE */
+/*
+ * Common USB/EHCI configuration
+ */
+#ifdef CONFIG_CMD_USB
+#define CONFIG_USB_EHCI /* Enable EHCI USB support */
+#define CONFIG_USB_EHCI_MARVELL
+#define ORION5X_USB20_HOST_PORT_BASE ORION5X_USB20_PORT0_BASE
+#define CONFIG_USB_STORAGE
+#define CONFIG_DOS_PARTITION
+#define CONFIG_ISO_PARTITION
+#define CONFIG_SUPPORT_VFAT
+#endif /* CONFIG_CMD_USB */
+
/*
* I2C related stuff
*/
/*
* Size of malloc() pool
*/
-#define CONFIG_SYS_MALLOC_LEN (1024 * 128) /* 128kB for malloc() */
+#define CONFIG_SYS_MALLOC_LEN (1024 * 256) /* 256kB for malloc() */
/*
* Other required minimal configurations
#define CONFIG_DISPLAY_CPUINFO /* Display cpu info */
#define CONFIG_NR_DRAM_BANKS 1
-#define CONFIG_STACKSIZE 0x00100000
#define CONFIG_SYS_LOAD_ADDR 0x00800000
#define CONFIG_SYS_MEMTEST_START 0x00400000
#define CONFIG_SYS_MEMTEST_END 0x007fffff
#define CONFIG_SYS_RESET_ADDRESS 0xffff0000
#define CONFIG_SYS_MAXARGS 16
+/* Use the HUSH parser */
+#define CONFIG_SYS_HUSH_PARSER
+
+/* Enable command line editing */
+#define CONFIG_CMDLINE_EDITING
+
+/* provide extensive help */
+#define CONFIG_SYS_LONGHELP
+
/* additions for new relocation code, must be added to all boards */
#define CONFIG_SYS_SDRAM_BASE 0
#define CONFIG_SYS_INIT_SP_ADDR \