#define CONFIG_405EX 1 /* Specifc 405EX support*/
#define CONFIG_SYS_CLK_FREQ 33333333 /* ext frequency to pll */
+#ifndef CONFIG_SYS_TEXT_BASE
+#define CONFIG_SYS_TEXT_BASE 0xFFFA0000
+#endif
+
+/*
+ * CHIP_21 errata - you must set this to match your exact CPU, else your
+ * board will not boot. DO NOT enable this unless you have JTAG available
+ * for recovery, in the event you get it wrong.
+ *
+ * Kilauea uses the 405EX, while Haleakala uses the 405EXr. Either board
+ * may be equipped for security or not. You must look at the CPU part
+ * number to be sure what you have.
+ */
+/* #define CONFIG_SYS_4xx_CHIP_21_405EX_NO_SECURITY */
+/* #define CONFIG_SYS_4xx_CHIP_21_405EX_SECURITY */
+/* #define CONFIG_SYS_4xx_CHIP_21_405EXr_NO_SECURITY */
+/* #define CONFIG_SYS_4xx_CHIP_21_405EXr_SECURITY */
+
/*
* Include common defines/options for all AMCC eval boards
*/
#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_early_init_f */
#define CONFIG_MISC_INIT_R 1 /* Call misc_init_r */
+#define CONFIG_BOARD_TYPES
#define CONFIG_BOARD_EMAC_COUNT
/*-----------------------------------------------------------------------
#define CONFIG_SYS_FLASH_BASE 0xFC000000
#define CONFIG_SYS_NAND_ADDR 0xF8000000
#define CONFIG_SYS_FPGA_BASE 0xF0000000
-#define CONFIG_SYS_PERIPHERAL_BASE 0xEF600000 /* internal peripherals*/
/*-----------------------------------------------------------------------
* Initial RAM & Stack Pointer Configuration Options
#define CONFIG_SYS_INIT_RAM_ADDR (CONFIG_SYS_SDRAM_BASE + (32 << 20)) /* 32 MiB */
#endif /* defined(CONFIG_SYS_INIT_DCACHE_CS) */
-#define CONFIG_SYS_INIT_RAM_END (4 << 10) /* 4 KiB */
-#define CONFIG_SYS_GBL_DATA_SIZE 256 /* num bytes initial data */
-#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE)
+#define CONFIG_SYS_INIT_RAM_SIZE (4 << 10) /* 4 KiB */
+#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
/*
* If the data cache is being used for the primordial stack and global
#if defined(CONFIG_SYS_INIT_DCACHE_CS)
# define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
-# define CONFIG_SYS_POST_ALT_WORD_ADDR (CONFIG_SYS_PERIPHERAL_BASE + GPT0_COMP6)
+# define CONFIG_SYS_POST_WORD_ADDR (CONFIG_SYS_PERIPHERAL_BASE + GPT0_COMP6)
#else
# define CONFIG_SYS_INIT_EXTRA_SIZE 16
# define CONFIG_SYS_INIT_SP_OFFSET (CONFIG_SYS_GBL_DATA_OFFSET - CONFIG_SYS_INIT_EXTRA_SIZE)
-# define CONFIG_SYS_POST_WORD_ADDR (CONFIG_SYS_GBL_DATA_OFFSET - 4)
# define CONFIG_SYS_OCM_DATA_ADDR CONFIG_SYS_INIT_RAM_ADDR
#endif /* defined(CONFIG_SYS_INIT_DCACHE_CS) */
* Serial Port
*----------------------------------------------------------------------*/
#define CONFIG_SYS_EXT_SERIAL_CLOCK 11059200 /* ext. 11.059MHz clk */
-/* define this if you want console on UART1 */
-#undef CONFIG_UART1_CONSOLE
+#define CONFIG_CONS_INDEX 1 /* Use UART0 */
/*-----------------------------------------------------------------------
* Environment
#define CONFIG_SYS_NAND_ECCSIZE 256
#define CONFIG_SYS_NAND_ECCBYTES 3
-#define CONFIG_SYS_NAND_ECCSTEPS (CONFIG_SYS_NAND_PAGE_SIZE / CONFIG_SYS_NAND_ECCSIZE)
#define CONFIG_SYS_NAND_OOBSIZE 16
-#define CONFIG_SYS_NAND_ECCTOTAL (CONFIG_SYS_NAND_ECCBYTES * CONFIG_SYS_NAND_ECCSTEPS)
#define CONFIG_SYS_NAND_ECCPOS {0, 1, 2, 3, 6, 7}
#ifdef CONFIG_ENV_IS_IN_NAND
#define CONFIG_SYS_NAND_BASE (CONFIG_SYS_NAND_ADDR + CONFIG_SYS_NAND_CS)
#define CONFIG_SYS_NAND_SELECT_DEVICE 1 /* nand driver supports mutipl. chips */
-#define CONFIG_SYS_64BIT_VSPRINTF /* needed for nand_util.c */
-
/*-----------------------------------------------------------------------
* DDR SDRAM
*----------------------------------------------------------------------*/
* SDRAM Controller DDR autocalibration values and takes a lot longer
* to run than Method_B.
* (See the Method_A and Method_B algorithm discription in the file:
- * cpu/ppc4xx/4xx_ibm_ddr2_autocalib.c)
+ * arch/powerpc/cpu/ppc4xx/4xx_ibm_ddr2_autocalib.c)
* Define CONFIG_PPC4xx_DDR_METHOD_A to use DDR autocalibration Method_A
*
* DDR Autocalibration Method_B is the default.
*/
#define CONFIG_CMD_CHIP_CONFIG
#define CONFIG_CMD_DATE
-#define CONFIG_CMD_LOG
#define CONFIG_CMD_NAND
#define CONFIG_CMD_PCI
#define CONFIG_CMD_SNTP
CONFIG_SYS_POST_UART)
/* Define here the base-addresses of the UARTs to test in POST */
-#define CONFIG_SYS_POST_UART_TABLE {UART0_BASE, UART1_BASE}
+#define CONFIG_SYS_POST_UART_TABLE { CONFIG_SYS_NS16550_COM1, \
+ CONFIG_SYS_NS16550_COM2 }
#define CONFIG_LOGBUFFER
#define CONFIG_SYS_POST_CACHE_ADDR 0x00800000 /* free virtual address */
#define CONFIG_SYS_EBC_PB1CR (CONFIG_SYS_NAND_ADDR | 0x1e000)
#endif
-/* Memory Bank 2 (FPGA) initialization */
-#define CONFIG_SYS_EBC_PB2AP 0x9400C800
-#define CONFIG_SYS_EBC_PB2CR (CONFIG_SYS_FPGA_BASE | 0x18000)
+/* Memory Bank 2 (FPGA) initialization */
+#define CONFIG_SYS_EBC_PB2AP (EBC_BXAP_BME_ENABLED | \
+ EBC_BXAP_FWT_ENCODE(6) | \
+ EBC_BXAP_BWT_ENCODE(1) | \
+ EBC_BXAP_BCE_DISABLE | \
+ EBC_BXAP_BCT_2TRANS | \
+ EBC_BXAP_CSN_ENCODE(0) | \
+ EBC_BXAP_OEN_ENCODE(0) | \
+ EBC_BXAP_WBN_ENCODE(3) | \
+ EBC_BXAP_WBF_ENCODE(1) | \
+ EBC_BXAP_TH_ENCODE(4) | \
+ EBC_BXAP_RE_DISABLED | \
+ EBC_BXAP_SOR_DELAYED | \
+ EBC_BXAP_BEM_WRITEONLY | \
+ EBC_BXAP_PEN_DISABLED)
+#define CONFIG_SYS_EBC_PB2CR (CONFIG_SYS_FPGA_BASE | 0x18000)
#define CONFIG_SYS_EBC_CFG 0x7FC00000 /* EBC0_CFG */
* Some Kilauea stuff..., mainly fpga registers
*/
#define CONFIG_SYS_FPGA_REG_BASE CONFIG_SYS_FPGA_BASE
-#define CONFIG_SYS_FPGA_FIFO_BASE (in32(CONFIG_SYS_FPGA_BASE) | (1 << 10))
+#define CONFIG_SYS_FPGA_FIFO_BASE (CONFIG_SYS_FPGA_BASE | (1 << 10))
/* interrupt */
#define CONFIG_SYS_FPGA_SLIC0_R_DPRAM_INT 0x80000000
#define CONFIG_SYS_FPGA_USER_LED0 0x00000200
#define CONFIG_SYS_FPGA_USER_LED1 0x00000100
+#define CONFIG_SYS_FPGA_MAGIC_MASK 0xffff0000
+#define CONFIG_SYS_FPGA_MAGIC 0xabcd0000
+#define CONFIG_SYS_FPGA_VER_MASK 0x0000ff00
+
#endif /* __CONFIG_H */
projects / karo-tx-uboot.git / blobdiff