+++ /dev/null
-/*
- * Copyright (C) 2006 Mihai Georgian <u-boot@linuxnotincluded.org.uk>
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-/*
- * Valid values for CONFIG_SYS_TEXT_BASE are:
- *
- * Standard configuration - all models
- * 0xFFF00000 boot from flash
- *
- * Test configuration (boot from RAM using uloader.o)
- * LinkStation HD-HLAN and KuroBox Standard
- * 0x03F00000 boot from RAM
- * LinkStation HD-HGLAN and KuroBox HG
- * 0x07F00000 boot from RAM
- */
-#ifndef CONFIG_SYS_TEXT_BASE
-#define CONFIG_SYS_TEXT_BASE 0xFFF00000
-#endif
-
-#if 0
-#define DEBUG
-#endif
-
-#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_early_init_f */
-
-/*-----------------------------------------------------------------------
- * User configurable settings:
- * Mandatory settings:
- * CONFIG_IPADDR_LS - the IP address of the LinkStation
- * CONFIG_SERVERIP_LS - the address of the server for NFS/TFTP/DHCP/BOOTP
- * Optional settins:
- * CONFIG_NCIP_LS - the adress of the computer running net console
- * if not configured, it will be set to
- * CONFIG_SERVERIP_LS
- */
-
-
-#define CONFIG_IPADDR_LS 192.168.11.150
-#define CONFIG_SERVERIP_LS 192.168.11.149
-
-#if !defined(CONFIG_IPADDR_LS) || !defined(CONFIG_SERVERIP_LS)
-#error Both CONFIG_IPADDR_LS and CONFIG_SERVERIP_LS must be defined
-#endif
-
-#if !defined(CONFIG_NCIP_LS)
-#define CONFIG_NCIP_LS CONFIG_SERVERIP_LS
-#endif
-
-/*----------------------------------------------------------------------
- * DO NOT CHANGE ANYTHING BELOW, UNLESS YOU KNOW WHAT YOU ARE DOING
- *---------------------------------------------------------------------*/
-
-#define CONFIG_MPC8245 1
-#define CONFIG_LINKSTATION 1
-
-/*---------------------------------------
- * Supported models
- *
- * LinkStation HDLAN /KuroBox Standard (CONFIG_HLAN)
- * LinkStation old model (CONFIG_LAN) - totally untested
- * LinkStation HGLAN / KuroBox HG (CONFIG_HGLAN)
- *
- * Models not supported yet
- * TeraStatin (CONFIG_HTGL)
- */
-
-#if defined(CONFIG_HLAN) || defined(CONFIG_LAN)
-#define CONFIG_IDENT_STRING " LinkStation / KuroBox"
-#elif defined(CONFIG_HGLAN)
-#define CONFIG_IDENT_STRING " LinkStation HG / KuroBox HG"
-#elif defined(CONFIG_HTGL)
-#define CONFIG_IDENT_STRING " TeraStation"
-#else
-#error No LinkStation model defined
-#endif
-
-#define CONFIG_BOOTDELAY 5
-#define CONFIG_ZERO_BOOTDELAY_CHECK
-#undef CONFIG_BOOT_RETRY_TIME
-
-#define CONFIG_AUTOBOOT_KEYED
-#define CONFIG_AUTOBOOT_PROMPT \
- "Boot in %02d seconds ('s' to stop)...", bootdelay
-#define CONFIG_AUTOBOOT_STOP_STR "s"
-
-#define CONFIG_CMD_IDE
-#define CONFIG_CMD_PCI
-#define CONFIG_CMD_DHCP
-#define CONFIG_CMD_PING
-#define CONFIG_CMD_EXT2
-
-#define CONFIG_BOOTP_SUBNETMASK
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
-#define CONFIG_BOOTP_NISDOMAIN
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_BOOTFILESIZE
-#define CONFIG_BOOTP_DNS
-#define CONFIG_BOOTP_DNS2
-#define CONFIG_BOOTP_SEND_HOSTNAME
-#define CONFIG_BOOTP_NTPSERVER
-#define CONFIG_BOOTP_TIMEOFFSET
-
-#define CONFIG_OF_LIBFDT 1
-
-#define OF_STDOUT_PATH "/soc10x/serial@80004600"
-
-/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
-#include <config_cmd_default.h>
-
-/*
- * Miscellaneous configurable options
- */
-#define CONFIG_SYS_LONGHELP /* undef to save memory */
-#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
-
-#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16)
-#define CONFIG_SYS_MAXARGS 16 /* Max number of command args */
-#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
-#define CONFIG_SYS_LOAD_ADDR 0x00800000 /* Default load address: 8 MB */
-
-#define CONFIG_BOOTCOMMAND "run bootcmd1"
-#define CONFIG_BOOTARGS "root=/dev/sda1 console=ttyS1,57600 netconsole=@192.168.1.7/eth0,@192.168.1.1/00:50:BF:A4:59:71 rtc-rs5c372.probe=0,0x32 debug"
-#define CONFIG_NFSBOOTCOMMAND "bootp;run nfsargs;bootm"
-
-#define CONFIG_SYS_CONSOLE_IS_IN_ENV
-
-#if defined(CONFIG_HLAN) || defined(CONFIG_LAN)
-#define UBFILE "share/u-boot/u-boot-hd.flash.bin"
-#elif defined(CONFIG_HGLAN)
-#define UBFILE "share/u-boot/u-boot-hg.flash.bin"
-#elif defined(CONFIG_HTGL)
-#define UBFILE "share/u-boot/u-boot-ht.flash.bin"
-#else
-#error No LinkStation model defined
-#endif
-
-#define CONFIG_EXTRA_ENV_SETTINGS \
- "autoload=no\0" \
- "stdin=nc\0" \
- "stdout=nc\0" \
- "stderr=nc\0" \
- "ipaddr="__stringify(CONFIG_IPADDR_LS)"\0" \
- "netmask=255.255.255.0\0" \
- "serverip="__stringify(CONFIG_SERVERIP_LS)"\0" \
- "ncip="__stringify(CONFIG_NCIP_LS)"\0" \
- "netretry=no\0" \
- "nc=setenv stdin nc;setenv stdout nc;setenv stderr nc\0" \
- "ser=setenv stdin serial;setenv stdout serial;setenv stderr serial\0" \
- "ldaddr=800000\0" \
- "hdpart=0:1\0" \
- "hdfile=boot/uImage\0" \
- "hdload=echo Loading ${hdpart}:${hdfile};ext2load ide ${hdpart} ${ldaddr} ${hdfile};ext2load ide ${hdpart} 7f0000 boot/kuroboxHG.dtb\0" \
- "boothd=setenv bootargs " CONFIG_BOOTARGS ";bootm ${ldaddr} - 7f0000\0" \
- "hdboot=run hdload;run boothd\0" \
- "flboot=setenv bootargs root=/dev/hda1;bootm ffc00000\0" \
- "emboot=setenv bootargs root=/dev/ram0;bootm ffc00000\0" \
- "nfsargs=setenv bootargs root=/dev/nfs rw nfsroot=${serverip}:${rootpath} " \
- "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}:${hostname}::off\0" \
- "bootretry=30\0" \
- "bootcmd1=run hdboot;run flboot\0" \
- "bootcmd2=run flboot\0" \
- "bootcmd3=run emboot\0" \
- "writeng=protect off fff70000 fff7ffff;era fff70000 fff7ffff;mw.l 800000 4e474e47 1;cp.b 800000 fff70000 4\0" \
- "writeok=protect off fff70000 fff7ffff;era fff70000 fff7ffff;mw.l 800000 4f4b4f4b 1;cp.b 800000 fff70000 4\0" \
- "ubpart=0:3\0" \
- "ubfile="UBFILE"\0" \
- "ubload=echo Loading ${ubpart}:${ubfile};ext2load ide ${ubpart} ${ldaddr} ${ubfile}\0" \
- "ubsaddr=fff00000\0" \
- "ubeaddr=fff2ffff\0" \
- "ubflash=protect off ${ubsaddr} ${ubeaddr};era ${ubsaddr} ${ubeaddr};cp.b ${ldaddr} ${ubsaddr} ${filesize};cmp.b ${ldaddr} ${ubsaddr} ${filesize}\0" \
- "upgrade=run ubload ubflash\0"
-
-/*-----------------------------------------------------------------------
- * PCI stuff
- */
-#define CONFIG_PCI
-#define CONFIG_PCI_INDIRECT_BRIDGE
-/* Verified: CONFIG_PCI_PNP doesn't work */
-#undef CONFIG_PCI_PNP
-#define CONFIG_PCI_SCAN_SHOW
-
-#ifndef CONFIG_PCI_PNP
-/* Keep the following defines in sync with the BAT mappings */
-
-#define PCI_ETH_IOADDR 0xbfff00
-#define PCI_ETH_MEMADDR 0xbffffc00
-#define PCI_IDE_IOADDR 0xbffed0
-#define PCI_IDE_MEMADDR 0xbffffb00
-#define PCI_USB0_IOADDR 0
-#define PCI_USB0_MEMADDR 0xbfffe000
-#define PCI_USB1_IOADDR 0
-#define PCI_USB1_MEMADDR 0xbfffd000
-#define PCI_USB2_IOADDR 0
-#define PCI_USB2_MEMADDR 0xbfffcf00
-
-#endif
-
-/*-----------------------------------------------------------------------
- * Ethernet stuff
- */
-
-#if defined(CONFIG_LAN) || defined(CONFIG_HLAN)
-#define CONFIG_TULIP
-#define CONFIG_TULIP_USE_IO
-#elif defined(CONFIG_HGLAN) || defined(CONFIG_HTGL)
-#define CONFIG_RTL8169
-#endif
-
-#define CONFIG_NET_RETRY_COUNT 5
-
-#define CONFIG_NETCONSOLE
-
-/*-----------------------------------------------------------------------
- * Start addresses for the final memory configuration
- * (Set up by the startup code)
- * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
- */
-#define CONFIG_SYS_SDRAM_BASE 0x00000000
-
-#define CONFIG_SYS_FLASH_BASE 0xFFC00000
-#define CONFIG_SYS_FLASH_SIZE 0x00400000
-#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE
-
-#define CONFIG_SYS_RESET_ADDRESS 0xFFF00100
-#define CONFIG_SYS_EUMB_ADDR 0x80000000
-#define CONFIG_SYS_PCI_MEM_ADDR 0xB0000000
-#define CONFIG_SYS_MISC_REGION_ADDR 0xFE000000
-
-#define CONFIG_SYS_MONITOR_LEN 0x00040000 /* 256 kB */
-#define CONFIG_SYS_MALLOC_LEN (512 << 10) /* Reserve some kB for malloc() */
-
-#define CONFIG_SYS_MEMTEST_START 0x00100000 /* memtest works on */
-#define CONFIG_SYS_MEMTEST_END 0x00800000 /* 1M ... 8M in DRAM */
-
-/* Maximum amount of RAM */
-#if defined(CONFIG_HLAN) || defined(CONFIG_LAN)
-#define CONFIG_SYS_MAX_RAM_SIZE 0x04000000 /* 64MB of SDRAM */
-#elif defined(CONFIG_HGLAN) || defined(CONFIG_HTGL)
-#define CONFIG_SYS_MAX_RAM_SIZE 0x08000000 /* 128MB of SDRAM */
-#else
-#error Unknown LinkStation type
-#endif
-
-/*-----------------------------------------------------------------------
- * Change CONFIG_SYS_TEXT_BASE in bord/linkstation/config.mk to get a RAM build
- *
- * RAM based builds are for testing purposes. A Linux module, uloader.o,
- * exists to load U-Boot and pass control to it
- *
- * Always do "make clean" after changing the build type
- */
-#if CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE
-#define CONFIG_SYS_RAMBOOT
-#endif
-
-/*-----------------------------------------------------------------------
- * Definitions for initial stack pointer and data area
- */
-#if 1 /* RAM is available when the first C function is called */
-#define CONFIG_SYS_INIT_RAM_ADDR (CONFIG_SYS_SDRAM_BASE + CONFIG_SYS_MAX_RAM_SIZE - 0x1000)
-#else
-#define CONFIG_SYS_INIT_RAM_ADDR 0x40000000
-#endif
-#define CONFIG_SYS_INIT_RAM_SIZE 0x1000
-#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
-
-/*----------------------------------------------------------------------
- * Serial configuration
- */
-#define CONFIG_CONS_INDEX 1
-#define CONFIG_BAUDRATE 57600
-
-#define CONFIG_SYS_NS16550
-#define CONFIG_SYS_NS16550_SERIAL
-
-#define CONFIG_SYS_NS16550_REG_SIZE 1
-
-#define CONFIG_SYS_NS16550_CLK get_bus_freq(0)
-
-#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_EUMB_ADDR + 0x4600) /* Console port */
-#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_EUMB_ADDR + 0x4500) /* AVR port */
-
-/*
- * Low Level Configuration Settings
- * (address mappings, register initial values, etc.)
- * You should know what you are doing if you make changes here.
- * For the detail description refer to the MPC8245 user's manual.
- *
- * Unless indicated otherwise, the values are
- * taken from the orignal Linkstation boot code
- *
- * Most of the low level configuration setttings are normally used
- * in arch/powerpc/cpu/mpc824x/cpu_init.c which is NOT used by this implementation.
- * Low level initialisation is done in board/linkstation/early_init.S
- * The values below are included for reference purpose only
- */
-
-/* FIXME: 32.768 MHz is the crystal frequency but */
-/* the real frequency is lower by about 0.75% */
-#define CONFIG_SYS_CLK_FREQ 32768000
-
-/* Bit-field values for MCCR1. */
-#define CONFIG_SYS_ROMNAL 0
-#define CONFIG_SYS_ROMFAL 11
-
-#define CONFIG_SYS_BANK0_ROW 2 /* Only bank 0 used: 13 x n x 4 */
-#define CONFIG_SYS_BANK1_ROW 0
-#define CONFIG_SYS_BANK2_ROW 0
-#define CONFIG_SYS_BANK3_ROW 0
-#define CONFIG_SYS_BANK4_ROW 0
-#define CONFIG_SYS_BANK5_ROW 0
-#define CONFIG_SYS_BANK6_ROW 0
-#define CONFIG_SYS_BANK7_ROW 0
-
-/* Bit-field values for MCCR2. */
-#define CONFIG_SYS_TSWAIT 0
-#if defined(CONFIG_LAN) || defined(CONFIG_HLAN)
-#define CONFIG_SYS_REFINT 0x15e0
-#elif defined(CONFIG_HGLAN) || defined(CONFIG_HTGL)
-#define CONFIG_SYS_REFINT 0x1580
-#endif
-
-/* Burst To Precharge. Bits of this value go to MCCR3 and MCCR4. */
-#define CONFIG_SYS_BSTOPRE 0x91c
-
-/* Bit-field values for MCCR3. */
-#define CONFIG_SYS_REFREC 7
-
-/* Bit-field values for MCCR4. */
-#define CONFIG_SYS_PRETOACT 2
-#define CONFIG_SYS_ACTTOPRE 2 /* Original value was 2 */
-#define CONFIG_SYS_ACTORW 2
-#if defined(CONFIG_LAN) || defined(CONFIG_HLAN)
-#define CONFIG_SYS_SDMODE_CAS_LAT 2 /* For 100MHz bus */
-/*#define CONFIG_SYS_SDMODE_BURSTLEN 3*/
-#elif defined(CONFIG_HGLAN) || defined(CONFIG_HTGL)
-#define CONFIG_SYS_SDMODE_CAS_LAT 3 /* For 133MHz bus */
-/*#define CONFIG_SYS_SDMODE_BURSTLEN 2*/
-#endif
-#define CONFIG_SYS_REGISTERD_TYPE_BUFFER 1
-#define CONFIG_SYS_EXTROM 1 /* Original setting but there is no EXTROM */
-#define CONFIG_SYS_REGDIMM 0
-#define CONFIG_SYS_DBUS_SIZE2 1
-#define CONFIG_SYS_SDMODE_WRAP 0
-
-#define CONFIG_SYS_PGMAX 0x32 /* All boards use this setting. Original 0x92 */
-#define CONFIG_SYS_SDRAM_DSCD 0x30
-
-/* Memory bank settings.
- * Only bits 20-29 are actually used from these vales to set the
- * start/end addresses. The upper two bits will always be 0, and the lower
- * 20 bits will be 0x00000 for a start address, or 0xfffff for an end
- * address. Refer to the MPC8240 book.
- */
-
-#define CONFIG_SYS_BANK0_START 0x00000000
-#define CONFIG_SYS_BANK0_END (CONFIG_SYS_MAX_RAM_SIZE - 1)
-#define CONFIG_SYS_BANK0_ENABLE 1
-#define CONFIG_SYS_BANK1_START 0x3ff00000
-#define CONFIG_SYS_BANK1_END 0x3fffffff
-#define CONFIG_SYS_BANK1_ENABLE 0
-#define CONFIG_SYS_BANK2_START 0x3ff00000
-#define CONFIG_SYS_BANK2_END 0x3fffffff
-#define CONFIG_SYS_BANK2_ENABLE 0
-#define CONFIG_SYS_BANK3_START 0x3ff00000
-#define CONFIG_SYS_BANK3_END 0x3fffffff
-#define CONFIG_SYS_BANK3_ENABLE 0
-#define CONFIG_SYS_BANK4_START 0x3ff00000
-#define CONFIG_SYS_BANK4_END 0x3fffffff
-#define CONFIG_SYS_BANK4_ENABLE 0
-#define CONFIG_SYS_BANK5_START 0x3ff00000
-#define CONFIG_SYS_BANK5_END 0x3fffffff
-#define CONFIG_SYS_BANK5_ENABLE 0
-#define CONFIG_SYS_BANK6_START 0x3ff00000
-#define CONFIG_SYS_BANK6_END 0x3fffffff
-#define CONFIG_SYS_BANK6_ENABLE 0
-#define CONFIG_SYS_BANK7_START 0x3ff00000
-#define CONFIG_SYS_BANK7_END 0x3fffffff
-#define CONFIG_SYS_BANK7_ENABLE 0
-
-#define CONFIG_SYS_ODCR 0x15
-
-/*----------------------------------------------------------------------
- * Initial BAT mappings
- */
-
-/* NOTES:
- * 1) GUARDED and WRITETHROUGH not allowed in IBATS
- * 2) CACHEINHIBIT and WRITETHROUGH not allowed together in same BAT
- */
-
-/* SDRAM */
-#define CONFIG_SYS_IBAT0L (CONFIG_SYS_SDRAM_BASE | BATL_PP_10 | BATL_MEMCOHERENCE)
-#define CONFIG_SYS_IBAT0U (CONFIG_SYS_SDRAM_BASE | BATU_BL_128M | BATU_VS | BATU_VP)
-
-#define CONFIG_SYS_DBAT0L CONFIG_SYS_IBAT0L
-#define CONFIG_SYS_DBAT0U CONFIG_SYS_IBAT0U
-
-/* EUMB: 1MB of address space */
-#define CONFIG_SYS_IBAT1L (CONFIG_SYS_EUMB_ADDR | BATL_PP_10 | BATL_CACHEINHIBIT)
-#define CONFIG_SYS_IBAT1U (CONFIG_SYS_EUMB_ADDR | BATU_BL_1M | BATU_VS | BATU_VP)
-
-#define CONFIG_SYS_DBAT1L (CONFIG_SYS_IBAT1L | BATL_GUARDEDSTORAGE)
-#define CONFIG_SYS_DBAT1U CONFIG_SYS_IBAT1U
-
-/* PCI Mem: 256MB of address space */
-#define CONFIG_SYS_IBAT2L (CONFIG_SYS_PCI_MEM_ADDR | BATL_PP_10 | BATL_CACHEINHIBIT)
-#define CONFIG_SYS_IBAT2U (CONFIG_SYS_PCI_MEM_ADDR | BATU_BL_256M | BATU_VS | BATU_VP)
-
-#define CONFIG_SYS_DBAT2L (CONFIG_SYS_IBAT2L | BATL_GUARDEDSTORAGE)
-#define CONFIG_SYS_DBAT2U CONFIG_SYS_IBAT2U
-
-/* PCI and local ROM/Flash: last 32MB of address space */
-#define CONFIG_SYS_IBAT3L (CONFIG_SYS_MISC_REGION_ADDR | BATL_PP_10 | BATL_CACHEINHIBIT)
-#define CONFIG_SYS_IBAT3U (CONFIG_SYS_MISC_REGION_ADDR | BATU_BL_32M | BATU_VS | BATU_VP)
-
-#define CONFIG_SYS_DBAT3L (CONFIG_SYS_IBAT3L | BATL_GUARDEDSTORAGE)
-#define CONFIG_SYS_DBAT3U CONFIG_SYS_IBAT3U
-
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 8 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- *
- * FIXME: This doesn't appear to be true for the newer kernels
- * which map more that 8 MB
- */
-#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
-
-/*-----------------------------------------------------------------------
- * FLASH organization
- */
-#define CONFIG_SYS_FLASH_CFI /* The flash is CFI compatible */
-#define CONFIG_FLASH_CFI_DRIVER /* Use common CFI driver */
-
-#undef CONFIG_SYS_FLASH_PROTECTION
-#define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_FLASH_BASE }
-#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* Max number of flash banks */
-#define CONFIG_SYS_MAX_FLASH_SECT 72 /* Max number of sectors per flash */
-
-#define CONFIG_SYS_FLASH_ERASE_TOUT 12000
-#define CONFIG_SYS_FLASH_WRITE_TOUT 1000
-
-#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 1 /* use buffered writes (20x faster) */
-
-#define CONFIG_SYS_FLASH_EMPTY_INFO /* print 'E' for empty sector on flinfo */
-#define CONFIG_SYS_FLASH_QUIET_TEST 1 /* don't warn upon unknown flash */
-
-#define CONFIG_ENV_IS_IN_FLASH
-/*
- * The original LinkStation flash organisation uses
- * 448 kB (0xFFF00000 - 0xFFF6FFFF) for the boot loader
- * We use the last sector of this area to store the environment
- * which leaves max. 384 kB for the U-Boot itself
- */
-#define CONFIG_ENV_ADDR 0xFFF60000
-#define CONFIG_ENV_SIZE 0x00010000
-#define CONFIG_ENV_SECT_SIZE 0x00010000
-
-/*-----------------------------------------------------------------------
- * Cache Configuration
- */
-#define CONFIG_SYS_CACHELINE_SIZE 32
-#ifdef CONFIG_CMD_KGDB
-#define CONFIG_SYS_CACHELINE_SHIFT 5 /* log base 2 of the above value */
-#endif
-
-/*-----------------------------------------------------------------------
- * IDE/ATA definitions
- */
-#undef CONFIG_IDE_LED /* No IDE LED */
-#define CONFIG_IDE_RESET /* no reset for ide supported */
-#define CONFIG_IDE_PREINIT /* check for units */
-#define CONFIG_LBA48 /* 48 bit LBA supported */
-
-#if defined(CONFIG_LAN) || defined(CONFIG_HLAN) || defined(CONFIG_HGLAN)
-#define CONFIG_SYS_IDE_MAXBUS 1 /* Scan only 1 IDE bus */
-#define CONFIG_SYS_IDE_MAXDEVICE 1 /* Only 1 drive per IDE bus */
-#elif defined(CONFIG_HGTL)
-#define CONFIG_SYS_IDE_MAXBUS 2 /* Max. 2 IDE busses */
-#define CONFIG_SYS_IDE_MAXDEVICE 2 /* max. 2 drives per IDE bus */
-#else
-#error Config IDE: Unknown LinkStation type
-#endif
-
-#define CONFIG_SYS_ATA_BASE_ADDR 0
-
-#define CONFIG_SYS_ATA_DATA_OFFSET 0 /* Offset for data I/O */
-#define CONFIG_SYS_ATA_REG_OFFSET 0 /* Offset for normal registers */
-#define CONFIG_SYS_ATA_ALT_OFFSET 0 /* Offset for alternate registers */
-
-/*-----------------------------------------------------------------------
- * Partitions and file system
- */
-#define CONFIG_DOS_PARTITION
-
-#endif /* __CONFIG_H */
projects / karo-tx-uboot.git / blobdiff