#ifndef __CONFIG_H
#define __CONFIG_H
-#include <asm/sizes.h>
/*
* High Level Configuration Options
*/
-#define CONFIG_ARMCORTEXA8 1 /* This is an ARM V7 CPU core */
#define CONFIG_OMAP 1 /* in a TI OMAP core */
#define CONFIG_OMAP34XX 1 /* which is a 34XX */
-#define CONFIG_OMAP3430 1 /* which is in a 3430 */
#define CONFIG_OMAP3_ZOOM2 1 /* working with Zoom II */
+#define CONFIG_OMAP_GPIO
+
+#define CONFIG_SDRC /* The chip has SDRC controller */
#include <asm/arch/cpu.h> /* get chip and board defs */
#include <asm/arch/omap3.h>
#define V_OSCK 26000000 /* Clock output from T2 */
#define V_SCLK (V_OSCK >> 1)
-#undef CONFIG_USE_IRQ /* no support for IRQs */
#define CONFIG_MISC_INIT_R
#define CONFIG_CMDLINE_TAG 1 /* enable passing of ATAGs */
#define CONFIG_INITRD_TAG 1
#define CONFIG_REVISION_TAG 1
+#define CONFIG_OF_LIBFDT 1
+
/*
* Size of malloc() pool
*/
-#define CONFIG_ENV_SIZE SZ_128K /* Total Size Environment */
+#define CONFIG_ENV_SIZE (128 << 10) /* 128 KiB */
/* Sector */
-#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + SZ_128K)
-#define CONFIG_SYS_GBL_DATA_SIZE 128 /* bytes reserved for */
- /* initial data */
+#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + (128 << 10))
/*
* Hardware drivers
*/
* NS16550 Configuration
* Zoom2 uses the TL16CP754C on the debug board
*/
-#define CONFIG_SERIAL_MULTI 1
/*
* 0 - 1 : first USB with respect to the left edge of the debug board
* 2 - 3 : second USB with respect to the left edge of the debug board
*/
-#define ZOOM2_DEFAULT_SERIAL_DEVICE (&zoom2_serial_device0)
+#define ZOOM2_DEFAULT_SERIAL_DEVICE 0
#define V_NS16550_CLK (1843200) /* 1.8432 Mhz */
/* allow to overwrite serial and ethaddr */
#define CONFIG_ENV_OVERWRITE
+#define CONFIG_GENERIC_MMC 1
#define CONFIG_MMC 1
-#define CONFIG_OMAP3_MMC 1
+#define CONFIG_OMAP_HSMMC 1
#define CONFIG_DOS_PARTITION 1
/* Status LED */
#define CONFIG_OMAP3_GPIO_3 /* board revision */
#define CONFIG_OMAP3_GPIO_5 /* debug board detection, ZOOM2_LED_BLUE */
+/* USB */
+#define CONFIG_MUSB_UDC 1
+#define CONFIG_USB_OMAP3 1
+#define CONFIG_TWL4030_USB 1
+
+/* USB device configuration */
+#define CONFIG_USB_DEVICE 1
+#define CONFIG_USB_TTY 1
+/* Change these to suit your needs */
+#define CONFIG_USBD_VENDORID 0x0451
+#define CONFIG_USBD_PRODUCTID 0x5678
+#define CONFIG_USBD_MANUFACTURER "Texas Instruments"
+#define CONFIG_USBD_PRODUCT_NAME "Zoom2"
+
/* commands to include */
#include <config_cmd_default.h>
#define CONFIG_HARD_I2C 1
#define CONFIG_SYS_I2C_SPEED 100000
#define CONFIG_SYS_I2C_SLAVE 1
-#define CONFIG_SYS_I2C_BUS 0
-#define CONFIG_SYS_I2C_BUS_SELECT 1
#define CONFIG_DRIVER_OMAP34XX_I2C 1
/*
#define GPMC_NAND_ECC_LP_x16_LAYOUT 1
#define CONFIG_SYS_MAX_NAND_DEVICE 1
-#define CONFIG_SYS_64BIT_VSPRINTF /* needed for nand_util.c */
-
/* Environment information */
#define CONFIG_BOOTDELAY 10
+#define CONFIG_EXTRA_ENV_SETTINGS \
+ "usbtty=cdc_acm\0" \
+
+#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM_1
+#define CONFIG_SYS_INIT_RAM_ADDR 0x4020f800
+#define CONFIG_SYS_INIT_RAM_SIZE 0x800
+#define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_INIT_RAM_ADDR + \
+ CONFIG_SYS_INIT_RAM_SIZE - \
+ GENERATED_GBL_DATA_SIZE)
/*
* Miscellaneous configurable options
*/
#define CONFIG_SYS_PROMPT "OMAP3 Zoom2 # "
#define CONFIG_SYS_LONGHELP
-#define CONFIG_SYS_CBSIZE 256
+#define CONFIG_SYS_CBSIZE 512
#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + \
sizeof(CONFIG_SYS_PROMPT) + 16)
#define CONFIG_SYS_MAXARGS 16
#define CONFIG_SYS_PTV 7 /* 2^(PTV+1) */
#define CONFIG_SYS_HZ ((V_SCLK) / (2 << CONFIG_SYS_PTV))
-/*-----------------------------------------------------------------------
- * Stack sizes
- *
- * The stack sizes are set up in start.S using these settings
- */
-#define CONFIG_STACKSIZE SZ_128K
-#ifdef CONFIG_USE_IRQ
-#define CONFIG_STACKSIZE_IRQ SZ_4K
-#define CONFIG_STACKSIZE_FIQ SZ_4K
-#endif
-
/*-----------------------------------------------------------------------
* Physical Memory Map
*/
#define CONFIG_NR_DRAM_BANKS 2 /* CS1 may or may not be populated */
#define PHYS_SDRAM_1 OMAP34XX_SDRC_CS0
-#define PHYS_SDRAM_1_SIZE SZ_32M /* at least 32 meg */
#define PHYS_SDRAM_2 OMAP34XX_SDRC_CS1
-/* SDRAM Bank Allocation method */
-#define SDRC_R_B_C 1
-
/*-----------------------------------------------------------------------
* FLASH and environment organization
*/
#define PISMO1_NAND_SIZE GPMC_SIZE_128M
#define PISMO1_ONEN_SIZE GPMC_SIZE_128M
-#define CONFIG_SYS_MAX_FLASH_SECT 520 /* max number of sectors on */
- /* one chip */
-#define CONFIG_SYS_MAX_FLASH_BANKS 2 /* max number of flash banks */
-#define CONFIG_SYS_MONITOR_LEN SZ_256K /* Reserve 2 sectors */
+#define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 2 sectors */
-#define CONFIG_SYS_FLASH_BASE boot_flash_base
+#if defined(CONFIG_CMD_NAND)
+#define CONFIG_SYS_FLASH_BASE PISMO1_NAND_BASE
+#endif
/* Monitor at start of flash */
#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE
#define CONFIG_ENV_IS_IN_NAND 1
#define SMNAND_ENV_OFFSET 0x0c0000 /* environment starts here */
-#define CONFIG_SYS_ENV_SECT_SIZE boot_flash_sec
-#define CONFIG_ENV_OFFSET boot_flash_off
+#define CONFIG_SYS_ENV_SECT_SIZE (128 << 10) /* 128 KiB */
+#define CONFIG_ENV_OFFSET SMNAND_ENV_OFFSET
#define CONFIG_ENV_ADDR SMNAND_ENV_OFFSET
-/*-----------------------------------------------------------------------
- * CFI FLASH driver setup
- */
-/* timeout values are in ticks */
-#define CONFIG_SYS_FLASH_ERASE_TOUT (100 * CONFIG_SYS_HZ)
-#define CONFIG_SYS_FLASH_WRITE_TOUT (100 * CONFIG_SYS_HZ)
-
-#ifndef __ASSEMBLY__
-extern struct gpmc *gpmc_cfg;
-extern unsigned int boot_flash_base;
-extern volatile unsigned int boot_flash_env_addr;
-extern unsigned int boot_flash_off;
-extern unsigned int boot_flash_sec;
-extern unsigned int boot_flash_type;
-#endif
+#define CONFIG_SYS_CACHELINE_SIZE 64
#endif /* __CONFIG_H */
projects / karo-tx-uboot.git / blobdiff