MX5: fix warning in clock.c

[karo-tx-uboot.git] / include / configs / sbc8560.h

diff --git a/include/configs/sbc8560.h b/include/configs/sbc8560.h
index 435b148f3c39ec9c11f868dc474c00131d0af126..46d60985d325e9750d29a00c069cf56144d71a5f 100644 (file)
--- a/include/configs/sbc8560.h
+++ b/include/configs/sbc8560.h
@@ -92,20 +92,6 @@
 #error "You can only use ONE of PCI Ethernet Card or TSEC Ethernet or CPM FCC."
 #endif
 
-/*
- * Base addresses -- Note these are effective addresses where the
- * actual resources get mapped (not physical addresses)
- */
-#define CONFIG_SYS_CCSRBAR_DEFAULT     0xff700000      /* CCSRBAR Default      */
-
-#if XXX
-  #define CONFIG_SYS_CCSRBAR           0xfdf00000      /* relocated CCSRBAR    */
-#else
-  #define CONFIG_SYS_CCSRBAR           0xff700000      /* default CCSRBAR      */
-#endif
-#define CONFIG_SYS_CCSRBAR_PHYS        CONFIG_SYS_CCSRBAR      /* physical addr of CCSRBAR */
-#define CONFIG_SYS_IMMR                CONFIG_SYS_CCSRBAR      /* PQII uses CONFIG_SYS_IMMR    */
-
 #define CONFIG_SYS_SDRAM_SIZE          512             /* DDR is 512MB */
 
 /* DDR Setup */
@@ -218,9 +204,6 @@
 
 /* Use the HUSH parser */
 #define CONFIG_SYS_HUSH_PARSER
-#ifdef CONFIG_SYS_HUSH_PARSER
-#define CONFIG_SYS_PROMPT_HUSH_PS2 "> "
-#endif
 
 /* pass open firmware flat tree */
 #define CONFIG_OF_LIBFDT                1
@@ -244,10 +227,6 @@
 
 #ifdef CONFIG_TSEC_ENET
 
-#ifndef CONFIG_NET_MULTI
-#define CONFIG_NET_MULTI       1
-#endif
-
 #ifndef CONFIG_MII
 #define CONFIG_MII             1       /* MII PHY management */
 #endif
@@ -278,8 +257,8 @@
      * - Select bus for bd/buffers
      * - Full duplex
      */
-    #define CONFIG_SYS_CMXFCR_MASK     (CMXFCR_FC2 | CMXFCR_RF2CS_MSK | CMXFCR_TF2CS_MSK)
-    #define CONFIG_SYS_CMXFCR_VALUE    (CMXFCR_RF2CS_CLK13 | CMXFCR_TF2CS_CLK14)
+    #define CONFIG_SYS_CMXFCR_MASK2    (CMXFCR_FC2 | CMXFCR_RF2CS_MSK | CMXFCR_TF2CS_MSK)
+    #define CONFIG_SYS_CMXFCR_VALUE2   (CMXFCR_RF2CS_CLK13 | CMXFCR_TF2CS_CLK14)
     #define CONFIG_SYS_CPMFCR_RAMTYPE  0
     #define CONFIG_SYS_FCC_PSMR        (FCC_PSMR_FDE)
 
@@ -446,8 +425,8 @@
  */
 
 #define CONFIG_HOSTNAME                SBC8560
-#define CONFIG_ROOTPATH                /home/ppc
-#define CONFIG_BOOTFILE                uImage
+#define CONFIG_ROOTPATH                "/home/ppc"
+#define CONFIG_BOOTFILE                "uImage"
 
 #define        CONFIG_EXTRA_ENV_SETTINGS               \
        "netdev=eth0\0"                         \