ARM: IXP: Remove dvl_host board

[karo-tx-uboot.git] / include / configs / ti_armv7_common.h

diff --git a/include/configs/ti_armv7_common.h b/include/configs/ti_armv7_common.h
index e0ab6912baf29ca2c9253c4f42ecd23f93663404..69d69a54212655ea772a46bb9f1fd5dbd5c6e6e5 100644 (file)
--- a/include/configs/ti_armv7_common.h
+++ b/include/configs/ti_armv7_common.h
@@ -45,27 +45,29 @@
 #define CONFIG_BOOTDELAY               1
 
 /*
- * DDR information.  We say (for simplicity) that we have 1 bank,
- * always, even when we have more.  We always start at 0x80000000,
- * and we place the initial stack pointer in our SRAM.
+ * DDR information.  If the CONFIG_NR_DRAM_BANKS is not defined,
+ * we say (for simplicity) that we have 1 bank, always, even when
+ * we have more.  We always start at 0x80000000, and we place the
+ * initial stack pointer in our SRAM. Otherwise, we can define
+ * CONFIG_NR_DRAM_BANKS before including this file.
  */
+#ifndef CONFIG_NR_DRAM_BANKS
 #define CONFIG_NR_DRAM_BANKS           1
+#endif
 #define CONFIG_SYS_SDRAM_BASE          0x80000000
 #define CONFIG_SYS_INIT_SP_ADDR         (NON_SECURE_SRAM_END - \
                                                GENERATED_GBL_DATA_SIZE)
 
 /* Timer information. */
 #define CONFIG_SYS_PTV                 2       /* Divisor: 2^(PTV+1) => 8 */
-#define CONFIG_SYS_HZ                  1000    /* 1ms clock */
 
 /* I2C IP block */
 #define CONFIG_I2C
 #define CONFIG_CMD_I2C
-#define CONFIG_HARD_I2C
-#define CONFIG_SYS_I2C_SPEED           100000
-#define CONFIG_SYS_I2C_SLAVE           1
-#define CONFIG_I2C_MULTI_BUS
-#define CONFIG_DRIVER_OMAP24XX_I2C
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_OMAP24_I2C_SPEED    100000
+#define CONFIG_SYS_OMAP24_I2C_SLAVE    1
+#define CONFIG_SYS_I2C_OMAP24XX
 
 /* MMC/SD IP block */
 #define CONFIG_MMC
@@ -87,10 +89,10 @@
  * access CS0 at is 0x8000000.
  */
 #ifdef CONFIG_NAND
-#define CONFIG_CMD_NAND
 #define CONFIG_NAND_OMAP_GPMC
 #define CONFIG_SYS_NAND_BASE           0x8000000
 #define CONFIG_SYS_MAX_NAND_DEVICE     1
+#define CONFIG_CMD_NAND
 #endif
 
 /*
@@ -103,14 +105,18 @@
  * console baudrate of 115200 and use the default baud rate table.
  */
 #define CONFIG_SYS_MALLOC_LEN          (1024 << 10)
-#define CONFIG_SYS_LONGHELP
 #define CONFIG_SYS_HUSH_PARSER
+#define CONFIG_SYS_PROMPT              "U-Boot# "
+#define CONFIG_SYS_CONSOLE_INFO_QUIET
+#define CONFIG_BAUDRATE                        115200
+#define CONFIG_ENV_VARS_UBOOT_CONFIG   /* Strongly encouraged */
+#define CONFIG_ENV_OVERWRITE           /* Overwrite ethaddr / serial# */
+
+/* As stated above, the following choices are optional. */
+#define CONFIG_SYS_LONGHELP
 #define CONFIG_AUTO_COMPLETE
 #define CONFIG_CMDLINE_EDITING
-#define CONFIG_SYS_PROMPT              "U-Boot# "
 #define CONFIG_VERSION_VARIABLE
-#define CONFIG_ENV_VARS_UBOOT_CONFIG
-#define CONFIG_BAUDRATE                        115200
 
 /* We set the max number of command args high to avoid HUSH bugs. */
 #define CONFIG_SYS_MAXARGS             64
@@ -123,9 +129,6 @@
 /* Boot Argument Buffer Size */
 #define CONFIG_SYS_BARGSIZE            CONFIG_SYS_CBSIZE
 
-#define CONFIG_ENV_OVERWRITE
-#define CONFIG_SYS_CONSOLE_INFO_QUIET
-
 /*
  * When we have SPI, NOR or NAND flash we expect to be making use of
  * mtdparts, both for ease of use in U-Boot and for passing information
@@ -141,7 +144,8 @@
  * useful commands.  Note that we must have set CONFIG_SYS_NO_FLASH
  * prior to this include, in order to skip a few commands.  When we do
  * have flash, if we expect these commands they must be enabled in that
- * config.
+ * config.  If desired, a specific list of desired commands can be used
+ * instead.
  */
 #include <config_cmd_default.h>
 #define CONFIG_CMD_ASKENV
@@ -200,7 +204,7 @@
 #define CONFIG_SPL_FAT_LOAD_PAYLOAD_NAME       "u-boot.img"
 
 #ifdef CONFIG_SPL_OS_BOOT
-#define CONFIG_SYS_SPL_ARGS_ADDR               (CONFIG_SYS_SDRAM_BASE + 0x100)
+#define CONFIG_SYS_SPL_ARGS_ADDR               0x80F80000
 
 /* FAT */
 #define CONFIG_SPL_FAT_LOAD_KERNEL_NAME                "uImage"
@@ -223,21 +227,20 @@
 #endif
 
 #ifdef CONFIG_MMC
+#define CONFIG_SPL_LIBDISK_SUPPORT
 #define CONFIG_SPL_MMC_SUPPORT
 #define CONFIG_SPL_FAT_SUPPORT
 #endif
 
-/* General parts of the framework. */
+/* General parts of the framework, required. */
 #define CONFIG_SPL_I2C_SUPPORT
 #define CONFIG_SPL_LIBCOMMON_SUPPORT
-#define CONFIG_SPL_LIBDISK_SUPPORT
 #define CONFIG_SPL_LIBGENERIC_SUPPORT
 #define CONFIG_SPL_SERIAL_SUPPORT
 #define CONFIG_SPL_GPIO_SUPPORT
 #define CONFIG_SPL_BOARD_INIT
 
 #ifdef CONFIG_NAND
-#define CONFIG_SPL_NAND_AM33XX_BCH     /* OMAP4 and later ELM support */
 #define CONFIG_SPL_NAND_SUPPORT
 #define CONFIG_SPL_NAND_BASE
 #define CONFIG_SPL_NAND_DRIVERS