vexpress64: use uncompressed kernel by default

[karo-tx-uboot.git] / include / configs / xilinx_zynqmp.h

diff --git a/include/configs/xilinx_zynqmp.h b/include/configs/xilinx_zynqmp.h
index d0ec3c066f33014b825fa2d65095a18071a8f8e7..880d29ca7157119e3de7b80137741d19bc141c13 100644 (file)
--- a/include/configs/xilinx_zynqmp.h
+++ b/include/configs/xilinx_zynqmp.h
@@ -61,16 +61,26 @@
 #define CONFIG_SYS_BAUDRATE_TABLE \
        { 4800, 9600, 19200, 38400, 57600, 115200 }
 
+#define CONFIG_ZYNQ_SDHCI0
+
 /* Command line configuration */
 #define CONFIG_CMD_ENV
 #define CONFIG_CMD_EXT2
 #define CONFIG_CMD_EXT4
 #define CONFIG_CMD_FAT
+#define CONFIG_CMD_FS_GENERIC
 #define CONFIG_CMD_MEMORY
 #define CONFIG_DOS_PARTITION
 #define CONFIG_CMD_ELF
 #define CONFIG_MP
 
+/* SPI */
+#ifdef CONFIG_ZYNQ_SPI
+# define CONFIG_SPI_FLASH
+# define CONFIG_SPI_FLASH_SST
+# define CONFIG_CMD_SF
+#endif
+
 #if defined(CONFIG_ZYNQ_SDHCI0) || defined(CONFIG_ZYNQ_SDHCI1)
 # define CONFIG_MMC
 # define CONFIG_GENERIC_MMC
@@ -92,8 +102,8 @@
        "kernel_addr=0x80000\0" \
        "fdt_addr=0x7000000\0" \
        "fdt_high=0x10000000\0" \
-       "sdboot=mmcinfo && fatload mmc 0:0 $fdt_addr system.dtb && " \
-               "fatload mmc 0:0 $kernel_addr Image && booti $kernel_addr - $fdt_addr\0"
+       "sdboot=mmcinfo && load mmc 0:0 $fdt_addr system.dtb && " \
+               "load mmc 0:0 $kernel_addr Image && booti $kernel_addr - $fdt_addr\0"
 
 #define CONFIG_BOOTARGS                "setenv bootargs console=ttyPS0,${baudrate} " \
                                "earlycon=cdns,mmio,0xff000000,${baudrate}n8"
@@ -119,6 +129,29 @@
 #define CONFIG_CMDLINE_EDITING
 #define CONFIG_SYS_MAXARGS             64
 
+#define CONFIG_ZYNQ_I2C0
+#define CONFIG_SYS_I2C_ZYNQ
+
+/* I2C */
+#if defined(CONFIG_SYS_I2C_ZYNQ)
+# define CONFIG_CMD_I2C
+# define CONFIG_SYS_I2C
+# define CONFIG_SYS_I2C_ZYNQ_SPEED             100000
+# define CONFIG_SYS_I2C_ZYNQ_SLAVE             0
+#endif
+
+#define CONFIG_ZYNQMP_EEPROM
+
+/* EEPROM */
+#ifdef CONFIG_ZYNQMP_EEPROM
+# define CONFIG_CMD_EEPROM
+# define CONFIG_SYS_I2C_EEPROM_ADDR_LEN                2
+# define CONFIG_SYS_I2C_EEPROM_ADDR            0x54
+# define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS     4
+# define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 5
+# define CONFIG_SYS_EEPROM_SIZE                        (64 * 1024)
+#endif
+
 #define CONFIG_FIT
 #define CONFIG_FIT_VERBOSE       /* enable fit_format_{error,warning}() */