x86: Remove eNET boards

[karo-tx-uboot.git] / include / configs / xpedite550x.h

diff --git a/include/configs/xpedite550x.h b/include/configs/xpedite550x.h
index a051913ffb27694c1033138176b26449f5fd40a6..2acf6c80a5eee260f9e75691b04e0284d8513c16 100644 (file)
--- a/include/configs/xpedite550x.h
+++ b/include/configs/xpedite550x.h
@@ -67,7 +67,7 @@
 #define CONFIG_SPD_EEPROM              /* Use SPD EEPROM for DDR setup */
 #define CONFIG_DDR_SPD
 #define CONFIG_MEM_INIT_VALUE          0xdeadbeef
-#define SPD_EEPROM_ADDRESS1                    0x54
+#define SPD_EEPROM_ADDRESS                     0x54
 #define SPD_EEPROM_OFFSET              0x200   /* OFFSET of SPD in EEPROM */
 #define CONFIG_NUM_DDR_CONTROLLERS     1
 #define CONFIG_DIMM_SLOTS_PER_CTLR     1
@@ -93,14 +93,8 @@ extern unsigned long get_board_ddr_clk(unsigned long dummy);
 #define CONFIG_BTB                     /* toggle branch predition */
 #define CONFIG_ENABLE_36BIT_PHYS       1
 
-/*
- * Base addresses -- Note these are effective addresses where the
- * actual resources get mapped (not physical addresses)
- */
-#define CONFIG_SYS_CCSRBAR_DEFAULT     0xff700000      /* CCSRBAR Default */
-#define CONFIG_SYS_CCSRBAR             0xef000000      /* relocated CCSRBAR */
-#define CONFIG_SYS_CCSRBAR_PHYS        CONFIG_SYS_CCSRBAR      /* physical addr of CCSRBAR */
-#define CONFIG_SYS_IMMR                CONFIG_SYS_CCSRBAR      /* PQII uses CONFIG_SYS_IMMR */
+#define CONFIG_SYS_CCSRBAR             0xef000000
+#define CONFIG_SYS_CCSRBAR_PHYS_LOW    CONFIG_SYS_CCSRBAR
 
 /*
  * Diagnostics
@@ -242,7 +236,6 @@ extern unsigned long get_board_ddr_clk(unsigned long dummy);
  * Use the HUSH parser
  */
 #define CONFIG_SYS_HUSH_PARSER
-#define CONFIG_SYS_PROMPT_HUSH_PS2     "> "
 
 /*
  * Pass open firmware flat tree
@@ -339,7 +332,6 @@ extern unsigned long get_board_ddr_clk(unsigned long dummy);
  */
 #define CONFIG_TSEC_ENET               /* tsec ethernet support */
 #define CONFIG_PHY_GIGE                1       /* Include GbE speed/duplex detection */
-#define CONFIG_NET_MULTI       1
 #define CONFIG_TSEC_TBI
 #define CONFIG_MII             1       /* MII PHY management */
 #define CONFIG_MII_DEFAULT_TSEC        1       /* Allow unregistered phys */
@@ -441,12 +433,6 @@ extern unsigned long get_board_ddr_clk(unsigned long dummy);
 #define CONFIG_SYS_BOOTMAPSZ   (16 << 20)      /* Initial Memory map for Linux*/
 #define CONFIG_SYS_BOOTM_LEN   (16 << 20)      /* Increase max gunzip size */
 
-/*
- * Boot Flags
- */
-#define BOOTFLAG_COLD          0x01            /* Normal Power-On: Boot from FLASH */
-#define BOOTFLAG_WARM          0x02            /* Software reboot */
-
 /*
  * Environment Configuration
  */
@@ -469,12 +455,12 @@ extern unsigned long get_board_ddr_clk(unsigned long dummy);
  * f6f00000 - f7efffff     Sec OS image (16MB)
  * f0000000 - f6efffff     Sec OS Use/Filesystem (111MB)
  */
-#define CONFIG_UBOOT1_ENV_ADDR MK_STR(0xfff80000)
-#define CONFIG_UBOOT2_ENV_ADDR MK_STR(0xf7f80000)
-#define CONFIG_FDT1_ENV_ADDR   MK_STR(0xfff00000)
-#define CONFIG_FDT2_ENV_ADDR   MK_STR(0xf7f00000)
-#define CONFIG_OS1_ENV_ADDR    MK_STR(0xfef00000)
-#define CONFIG_OS2_ENV_ADDR    MK_STR(0xf6f00000)
+#define CONFIG_UBOOT1_ENV_ADDR __stringify(0xfff80000)
+#define CONFIG_UBOOT2_ENV_ADDR __stringify(0xf7f80000)
+#define CONFIG_FDT1_ENV_ADDR   __stringify(0xfff00000)
+#define CONFIG_FDT2_ENV_ADDR   __stringify(0xf7f00000)
+#define CONFIG_OS1_ENV_ADDR    __stringify(0xfef00000)
+#define CONFIG_OS2_ENV_ADDR    __stringify(0xf6f00000)
 
 #define CONFIG_PROG_UBOOT1                                             \
        "$download_cmd $loadaddr $ubootfile; "                          \