* Each interface may have alternate settings. The initial configuration
* of a device sets altsetting 0, but the device driver can change
* that setting using usb_set_interface(). Alternate settings are often
- * used to control the the use of periodic endpoints, such as by having
+ * used to control the use of periodic endpoints, such as by having
* different endpoints use different amounts of reserved USB bandwidth.
* All standards-conformant USB devices that use isochronous endpoints
* will use them in non-default settings.
* active alternate setting */
unsigned num_altsetting; /* number of alternate settings */
+ /* If there is an interface association descriptor then it will list
+ * the associated interfaces */
+ struct usb_interface_assoc_descriptor *intf_assoc;
+
int minor; /* minor number this interface is
* bound to */
enum usb_interface_condition condition; /* state of binding */
/* this maximum is arbitrary */
#define USB_MAXINTERFACES 32
+#define USB_MAXIADS USB_MAXINTERFACES/2
/**
* struct usb_interface_cache - long-term representation of a device interface
struct usb_config_descriptor desc;
char *string; /* iConfiguration string, if present */
+
+ /* List of any Interface Association Descriptors in this
+ * configuration. */
+ struct usb_interface_assoc_descriptor *intf_assoc[USB_MAXIADS];
+
/* the interfaces associated with this configuration,
* stored in no particular order */
struct usb_interface *interface[USB_MAXINTERFACES];
unsigned auto_pm:1; /* autosuspend/resume in progress */
unsigned do_remote_wakeup:1; /* remote wakeup should be enabled */
+ unsigned reset_resume:1; /* needs reset instead of resume */
+ unsigned persist_enabled:1; /* USB_PERSIST enabled for this dev */
unsigned autosuspend_disabled:1; /* autosuspend and autoresume */
unsigned autoresume_disabled:1; /* disabled by the user */
#endif
.idVendor = (vend), .idProduct = (prod), \
.bcdDevice_lo = (lo), .bcdDevice_hi = (hi)
+/**
+ * USB_DEVICE_INTERFACE_PROTOCOL - macro used to describe a usb
+ * device with a specific interface protocol
+ * @vend: the 16 bit USB Vendor ID
+ * @prod: the 16 bit USB Product ID
+ * @pr: bInterfaceProtocol value
+ *
+ * This macro is used to create a struct usb_device_id that matches a
+ * specific interface protocol of devices.
+ */
+#define USB_DEVICE_INTERFACE_PROTOCOL(vend,prod,pr) \
+ .match_flags = USB_DEVICE_ID_MATCH_DEVICE | USB_DEVICE_ID_MATCH_INT_PROTOCOL, \
+ .idVendor = (vend), \
+ .idProduct = (prod), \
+ .bInterfaceProtocol = (pr)
+
/**
* USB_DEVICE_INFO - macro used to describe a class of usb devices
* @cl: bDeviceClass value
.match_flags = USB_DEVICE_ID_MATCH_INT_INFO, .bInterfaceClass = (cl), \
.bInterfaceSubClass = (sc), .bInterfaceProtocol = (pr)
+/**
+ * USB_DEVICE_AND_INTERFACE_INFO - macro used to describe a specific usb device
+ * with a class of usb interfaces
+ * @vend: the 16 bit USB Vendor ID
+ * @prod: the 16 bit USB Product ID
+ * @cl: bInterfaceClass value
+ * @sc: bInterfaceSubClass value
+ * @pr: bInterfaceProtocol value
+ *
+ * This macro is used to create a struct usb_device_id that matches a
+ * specific device with a specific class of interfaces.
+ *
+ * This is especially useful when explicitly matching devices that have
+ * vendor specific bDeviceClass values, but standards-compliant interfaces.
+ */
+#define USB_DEVICE_AND_INTERFACE_INFO(vend,prod,cl,sc,pr) \
+ .match_flags = USB_DEVICE_ID_MATCH_INT_INFO \
+ | USB_DEVICE_ID_MATCH_DEVICE, \
+ .idVendor = (vend), .idProduct = (prod), \
+ .bInterfaceClass = (cl), \
+ .bInterfaceSubClass = (sc), .bInterfaceProtocol = (pr)
+
/* ----------------------------------------------------------------------- */
/* Stuff for dynamic usb ids */
* do (or don't) show up otherwise in the filesystem.
* @suspend: Called when the device is going to be suspended by the system.
* @resume: Called when the device is being resumed by the system.
+ * @reset_resume: Called when the suspended device has been reset instead
+ * of being resumed.
* @pre_reset: Called by usb_reset_composite_device() when the device
* is about to be reset.
* @post_reset: Called by usb_reset_composite_device() after the device
- * has been reset.
+ * has been reset, or in lieu of @resume following a reset-resume
+ * (i.e., the device is reset instead of being resumed, as might
+ * happen if power was lost). The second argument tells which is
+ * the reason.
* @id_table: USB drivers use ID table to support hotplugging.
* Export this with MODULE_DEVICE_TABLE(usb,...). This must be set
* or your driver's probe function will never get called.
int (*suspend) (struct usb_interface *intf, pm_message_t message);
int (*resume) (struct usb_interface *intf);
+ int (*reset_resume)(struct usb_interface *intf);
- void (*pre_reset) (struct usb_interface *intf);
- void (*post_reset) (struct usb_interface *intf);
+ int (*pre_reset)(struct usb_interface *intf);
+ int (*post_reset)(struct usb_interface *intf);
const struct usb_device_id *id_table;
#define URB_ZERO_PACKET 0x0040 /* Finish bulk OUT with short packet */
#define URB_NO_INTERRUPT 0x0080 /* HINT: no non-error interrupt
* needed */
+#define URB_FREE_BUFFER 0x0100 /* Free transfer buffer with the URB */
struct usb_iso_packet_descriptor {
unsigned int offset;
struct urb;
+struct usb_anchor {
+ struct list_head urb_list;
+ wait_queue_head_t wait;
+ spinlock_t lock;
+};
+
+static inline void init_usb_anchor(struct usb_anchor *anchor)
+{
+ INIT_LIST_HEAD(&anchor->urb_list);
+ init_waitqueue_head(&anchor->wait);
+ spin_lock_init(&anchor->lock);
+}
+
typedef void (*usb_complete_t)(struct urb *);
/**
* struct urb - USB Request Block
* @urb_list: For use by current owner of the URB.
+ * @anchor_list: membership in the list of an anchor
+ * @anchor: to anchor URBs to a common mooring
* @pipe: Holds endpoint number, direction, type, and more.
* Create these values with the eight macros available;
* usb_{snd,rcv}TYPEpipe(dev,endpoint), where the TYPE is "ctrl"
/* public: documented fields in the urb that can be used by drivers */
struct list_head urb_list; /* list head for use by the urb's
* current owner */
+ struct list_head anchor_list; /* the URB may be anchored by the driver */
+ struct usb_anchor *anchor;
struct usb_device *dev; /* (in) pointer to associated device */
unsigned int pipe; /* (in) pipe information */
int status; /* (return) non-ISO status */
extern int usb_submit_urb(struct urb *urb, gfp_t mem_flags);
extern int usb_unlink_urb(struct urb *urb);
extern void usb_kill_urb(struct urb *urb);
+extern void usb_kill_anchored_urbs(struct usb_anchor *anchor);
+extern void usb_anchor_urb(struct urb *urb, struct usb_anchor *anchor);
+extern void usb_unanchor_urb(struct urb *urb);
+extern int usb_wait_anchor_empty_timeout(struct usb_anchor *anchor,
+ unsigned int timeout);
void *usb_buffer_alloc (struct usb_device *dev, size_t size,
gfp_t mem_flags, dma_addr_t *dma);